聚苯胺表面修饰芳纶浆粕及其纸基材料的导电性能

通过在芳纶浆粕(AP)表面修饰聚苯胺(PANI)制备了聚苯胺-芳纶浆粕(PANI-AP), 然后与碳纤维(CF)共混, 采用湿法抄纸技术制备导电性能优异的纸基材料(PANI-AP/CP). 对其形貌结构、 导电性能及PANI分布均匀性进行了表征, 并研究了环境湿度、 温度、 pH值及放置时间对PANI-AP/CP导电性能的影响. 研究结果表明, PANI-AP表面粗糙度增加, 结晶度增加, 出现含醌式结构的导电PANI的衍射峰, 说明PANI成功修饰于AP表面. 采用该方法制备的PANI-AP/CP导电性能与分布均匀性均得到提高, 相对于碳纤维纸基材(CP), PANI-AP/CP的电导率为3.937 S/cm, 导电性能提高153.5%. 与PANI原位生长于CP(AP/CP-PANI)相比, PANI-AP/CP的导电性能提高34.6%, 总色差值(DE)降低74.9%.     

不同质子酸掺杂对银/聚苯胺纳米复合材料结构和导电性的影响

利用紫外光作为辅助条件,在反胶束体系中采用一步双原位法合成了硝酸(HNO3)、对甲基苯磺酸(TSA)和5-磺基水杨酸(SSA)掺杂的银/聚苯胺(Ag/PANI)纳米复合材料.通过对复合材料进行红外光谱(FTIR)、紫外光谱(UV-Vis)、扫描电镜(SEM)、X射线衍射(XRD)和导电性能的测试,研究了不同质子酸对Ag/PANI纳米复合材料结构、形貌和导电性能的影响.测试结果表明,3种酸掺杂制备的Ag/PANI纳米复合材料均为聚苯胺包覆银粒子的核-壳结构.不同的质子酸掺杂会对Ag/PANI纳米复合材料的电性能有重要影响.在3种酸掺杂的复合材料中,TSA掺杂的复合材料的电导率最佳,为215.14 S·cm-1.     

PANI膜电聚合过程及电控分离苯酚的EQCM研究

通过电沉积方法在镀铂石英晶片上制备了导电聚苯胺(PANI)膜,采用电化学石英晶体微天平(EQCM)技术探讨了苯胺聚合机制及在苯酚溶液中的氧化还原特性.在0.5 mol/L硫酸溶液中结合循环伏安法考察了PANI膜在完全还原态(L)-半氧化态(E)-完全氧化态(P)之间的电活性和稳定性;在不同浓度的苯酚溶液中结合恒电压阶跃...     

尺寸可控的聚苯胺复合微球的电纺制备与表征

以十二烷基苯磺酸(DBSA)掺杂的导电聚苯胺与聚乙二醇(PEG)及Fe3O4的混合氯仿溶液,采用静电纺丝(spinning technology)方法制备含Fe3O4纳米颗粒的导电聚苯胺(PANI)/PEG/Fe3O4复合微球.SEM结果表明,电纺所得的PANI/PEG/Fe3O4复合微球结构依赖于PEG聚合物浓度、静...     

磁场对微乳液法合成聚苯胺结构及其电化学行为的影响

在不同磁场强度下,采用微乳液聚合法合成导电聚苯胺(PANI),以碳纸负载PANI为工作电极,通过循环伏安测试方法,探讨了磁场、氧化剂浓度和聚合时间对微乳液聚合法合成PANI电化学性能的影响;并通过X射线衍射(XRD)、四探针电导率测试和傅立叶红外光谱(FTIR)对产物结构和性能的表征分析,印证了循环伏安分析结果的可靠性.实验结果表明,与无磁条件下制备的PANI相比,磁场条件下制备的PANI具有较高的导电性和规整度;FTIR谱图分析表明,由于磁场的取向作用使分子间相互作用力降低,分子链离域程度增大,使磁场条件下合成PANI的主要特征峰有向低频方向移动的趋势,但分子的基本结构单元没有发生变化.研究结果显示,利用负载PANI的碳纸为工作电极,能够对微乳液法合成PANI的电化学行为进行有效的实时表征.     

电致变色型导电聚苯胺固态超级电容器的构建与性能研究

以苯胺硫酸溶液为沉积液,导电玻璃(FTO)为基底材料,在-0.2~1.2 V范围内先电位扫描一圈生成聚苯胺(PANI)晶种,然后在-0.2~0.8 V范围内用循环伏安法电沉积导电PANI材料.所得样品用红外光谱和扫描电子显微镜进行结构表征;以最佳循环伏安电沉积条件制备的PANI/FTO为活性电极,以H_2SO_4/聚乙烯醇(H2SO4/PVA)为凝胶电解质组装了电化学电容器,通过循环伏安、恒电流充放电和电化学阻抗法研究了组装电化学电容器的电化学性能.研究结果表明,以H_2SO_4/PVA凝胶电解质,沉积于导电玻璃表面的PANI活性电极材料的面比电容可达172.7 m F/cm~2,并且在2000次充放电以后,比电容值仍可保留初始值的92.8%.以分区沉积有PANI的导电玻璃可组装制备通过变色显示充放电过程的电化学电容器,在充电时,其颜色逐渐从浅绿色向深绿色转变,放电时,颜色逐渐从深绿色向浅绿色转变.     

原位聚合法制备PANI/PET导电织物及其性能分析

在聚酯纤维基材及其织物表面,原位聚合形成厚度约1~2μm聚苯胺包覆层,制得聚苯胺(PANI)/聚酯(PET)导电织物.PANI层优异的导电性能使之成为有广阔发展前景的柔性电磁屏蔽材料.正交试验分析研究了苯胺单体浓度、氧化剂:苯胺摩尔比、掺杂酸浓度、反应时间对PANI包覆层外观形态、与基体结合牢度以及导电性的影响.实验表明:在经适当前处理的PET基材表面,以苯胺单体浓度为0.25mol/L、氧化剂与苯胺摩尔比为1∶1、掺杂酸浓度0.5 mol/L、反应时间60 min、反应温度为0~20℃时制备的PANI/PET导电织物方阻最小,导电性最好;掺杂酸酸性越强,导电性越好.SEM、FTIR及XRD测试表明涤纶织物表面有均匀连续的聚苯胺膜存在.分析表明聚苯胺分子链中氧化结构与还原结构含量基本相等,说明聚苯胺渗入纤维内部,使纤维无定形区面积增加,结晶度减小.     

一步乳液聚合法制备高溶解性导电聚苯胺

报道了一种高溶解性导电聚苯胺(PANI)的制备方法,以聚2-丙烯酰胺-2-甲基丙磺酸(PAMPS)作为掺杂酸和乳化剂,利用其特有的长链、亲水性及强酸性基团效应,通过乳液聚合法一步合成出具有较高溶解性的导电聚苯胺。利用核磁共振光谱仪(NMR)、傅里叶红外光谱仪(FT-IR)和扫描电子显微镜(SEM)等技术手段对产物结构和性能进行了表征分析。结果表明,在m(苯胺)∶m(AMPS)∶m(APS)=1∶2∶1.5;AMPS质量分数为20%;APS质量分数为30%;反应时间为5 h;反应温度为5℃的条件下,聚苯胺的产率高达86%,在有机溶剂二甲基甲酰胺(DMF)中的溶解度可达0.3814 g/g,在水中的溶解度可达0.2123 g/g,电导率达5.9 S/cm。     

WO3/PANI核壳结构反蛋白石薄膜的电致变色性能

采用连续离子层吸附法在反蛋白石结构三氧化钨(IO-WO₃)薄膜表面引入导电聚合物聚苯胺(PANI)层, 制备了独特的WO₃/PANI核壳结构反蛋白石薄膜(IO-WO₃/PANI). 探究了IO-WO₃/PANI薄膜的形貌、 组成和电化学行为. 结果表明, 当电位扫描范围为-0.6~1.0 V时, IO-WO₃/PANI复合膜在不同电压状态下会呈现出4种不同的颜色, 分别为蓝色(1.0 V)、 绿色(0.2 V)、 浅绿色(0 V)和蓝紫色(-0.6 V). 与IO-WO₃薄膜相比, IO-WO₃/PANI复合膜的电致变色性能显著提高, 其着色与退色响应时间分别为3.8和6.14 s, 变色效率(CE)值为201.1 cm²/C. 电致变色性能的改善主要归因于WO₃与PANI形成给体-受体体系和核壳反蛋白石等级孔结构, 使得离子快速扩散, 并为电荷转移反应提供更大的表面积. 研究结果表明, IO-WO₃/PANI核壳结构反蛋白石薄膜是一种潜在的多色电致变色材料, 具有广阔的应用前景.     

电化学组装法制备对-巯基苯胺/聚苯胺纳米有序导电聚合物膜

提出了制备二维纳米有序有机导电聚合物膜的新方法--电化学组装法,应用该方法在电位脉冲的作用下使苯胺聚合到对-巯基苯胺修饰的金电极上,获得了致密、有序的对-巯基苯胺/聚苯胺(p-aminothiolphenol/polyaniline,PATP/PANI)导电寡聚物薄膜.用STM研究了Au(111)/PATP、Au(111)/PATP/PANI膜表面的二维有序性,用SERS谱表征了Au(粗糙表面)/PATP、Au(粗糙表面)/PATP/PANI膜的结构和成分,并以[Fe(CN)₆]^3-/[Fe(CN)₆]^4-为探针研究了其电子传递性能.结果表明用电化学组装法制备的PATP/PANI膜在纳米尺度上是二维有序的,且具有良好的电子传递性能.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.