芴取代的有机膦化合物的合成及发光性能

合成了以芴为取代基，P原子为核的一类新型有机膦化合物．此类化合物的HOMO值在-5．35～-5．24eV之间．在二氯甲烷中的最大紫外吸收光谱峰值在313～351nm之间，荧光光谱峰值在334～397nm之间．利用此类小分子与纯聚芴进行掺杂，制作了有机电致发光器件．低HOMO值有机膦化合物的引入有效地降低了聚芴发光器件的开启电压，提高了器件的发光效率．     

电致蓝光芴取代聚芴的合成与光谱稳定性

为了筛选高效稳定的聚合物电致蓝光材料, 设计合成了三苯胺和芴取代的二芳基芴单体, 并通过Suzuki缩聚合成了交替共聚物TPAFF-co-F和TPAFF-co-P. 将二辛基芴引入聚芴的9位可以增加其溶解度, 同时具有屏蔽主链和减少主链芴9位被氧化的作用, 三苯胺基团将有利于提高空穴在阳极界面的注入能力. 200 ℃下空气中退火24 h实验表明, 在相同条件下, 绿光指数(Igreen/Iblue)顺序为聚(9,9-二辛基芴)(1.07)>TPAFF-co-F(0.65)>TPAFF-co-P (0.47), 证明了烷基芴引入减少了主链氧化的几率. 还制作了发光二极管器件, 其结构为ITO/PEDOT:PSS(40 nm)/TPAFF-co-F或TPAFF-co-P(80 nm)/Ba(4 nm)/Al(120 nm). 在高电流密度下它们保持了良好的光谱稳定性, 在547 mA·cm-2电流密度下, TPAFF-co-F的CIE(国际发光照明委员会)坐标为(0.22, 0.24), TPAFF-co-P的CIE坐标为(0.24, 0.26), 后者的电流效率为0.712 cd·A-1.     

烷基芴与三苯胺取代-3,6-芴共聚物的合成及其性能

用Suzuki偶联反应制备了一系列新型的9,9-二辛基-2,7-芴(DOF)与9,9-二(4-二苯胺基苯基)-3,6-芴(36FT)的共聚物. 所有的聚合物均可溶于常见的有机溶剂(如THF, CHCl3和甲苯等), 分子量在47000~189000之间. 电化学研究结果表明, 所有聚合物的HOMO能级都高于均聚烷基芴, 并且随着36FT含量的增加, HOMO值逐渐上升. 以该类聚合物为发光层制作了结构为ITO/PEDOT/PVK/polymer/Ba/Al的器件, 获得了稳定的蓝光发射, 其中以36PFT10为发光层的器件获得了0.52%的最大外量子效率.     

低聚乙氧基醚链修饰的两亲性钯化合物及催化合成聚芴

合成了一系列不同链长的双低聚乙氧基醚链修饰的三苯基膦,并以此为配体制备了相应的二价钯化合物.此类化合物在空气中具有良好稳定性,易溶于常用的有机溶剂.作为单组份催化剂,在无相转移试剂及无需补加膦配体条件下,能够有效催化Suzuki缩聚反应.在甲苯/水聚合体系中,可得到数均分子量(Mn)为7×104左右的聚芴.随着乙氧基醚链单元数的增加,Mn提高至近1×105.GPC谱图分析证实,亲水基团的引入使钯化合物具有了明显的两亲性,进而促进了金属转移步骤,使得聚合物分子量得以提高.     

螺二芴基可溶性共聚物的合成及发光性能

以9,9'-螺二芴和不同链长的二烷氧基苯为单体, 以FeCl3为催化剂, 采用化学氧化法合成了一系列聚合物发光材料. 溶解度测试表明, 共聚物在二氯甲烷、四氢呋喃(THF)、氯仿等极性溶剂中具有良好的溶解性. 利用核磁共振氢谱(1H NMR)、傅里叶变换红外(FT-IR)光谱、紫外-可见(UV-Vis)光谱和荧光(PL)光谱研究了共聚物的化学结构和发光性能, 结果表明共聚物在二甲基亚砜(DMSO)中均发射蓝色荧光, 最大吸收和荧光发射峰分别为356和413 nm. 以硫酸奎宁溶液作为参比, 测得共聚物的荧光量子效率为0.69至0.77. 通过循环伏安法(CV)测得所合成的三种共聚物的最高占有分子轨道(HOMO)能级均位于-5.85至-5.69 eV之间.     

9,9-二己基芴基四乙炔基聚炔铂的合成及发光性质

Soluble platinum(Ⅱ)polyyne polymers trans-{Pt-[P(C_4H_8N)_3]_2(C≡C)_2R(C≡C)_(2-)}_n and trans-{Pt-[P(C_4-H_3O)_3]_2(C≡C)_2R(C≡C)_(2-)}_n(R=9,9-dihexylfluorene-2,7-diyl)have been prepared in good yields by CuI-catalyzedpolymerization involving the dehydrohalogenating coupling of trans-{PtCl_2[P(C_4H_8N)_3]_2} and trans-{PtCl_2[P-(C_4H_3O)_3]_2} with H(C≡C)_2R(C≡C)_2H,respectively.We report the optical spectroscopy of these polyplatinaynes.The influence of the heavy metal atom in these metal alkynyl systems on the intersystem crossing rate and the spa-tial extent of lowest singlet and triplet excitons was systematically characterized.Our investigations indicate that theorganic triplet emissions can be harvested by the heavy-atom effect which enables efficient intersystem crossingfrom the S_1 singlet excited state to the T_1 triplet excited state.     

含有手性和发光官能团侧基的聚1-苯基-1-辛炔的合成与性能研究

设计并合成了一系列含手性和发光生色团侧基的聚（1-苯基-1-辛炔）衍生物{-[（C6H13）C=C（C6H4-p-CO2-R）]n-,R=[（1S）-endo]-（-）-冰片基（P3）,（1R,2S,5R）-（-）-薄荷基（P4）,-C6H4-p-（1R,2S,5R）-（-）-薄荷基（P5）,2-萘基（P6）,4-联苯基（P7）}.用WCl6-Ph4Sn作催化剂,成功地制备了这些具有中等产率和高分子量（Mw高达64000）的聚合物.聚合物的结构和性能通过NMR,TGA,UV,CD,PL和EL等分析方法进行了表征.所有聚合物都表现出良好的热稳定性,在N2保护条件下,其失重5%的温度在300～416℃之间.所有聚合物的带隙约为3.0eV.聚合物P4和P5表现出与聚合物链段螺旋性相对应的CD吸收.在UV辐照下,P3～P7的THF溶液均发射强烈蓝光,其最大发射波长位于485nm左右,量子效率均高于20%.聚合物薄膜发射与其溶液发射在相同的光谱区域,并表现出轻微的聚集诱导猝灭.制备了ITO/聚合物：PVK/BCP/Alq3/LiF/Al多层聚合物EL器件,其最大发射波长为487nm.随着侧基的改变,器件的最大亮度和外量子效率也随之发生变化,其中P6表现出最高的外量子效率（0.16%）.EL器件均具有良好的光谱稳定性,其EL最大发射峰几乎不随外加电压的变化而改变.     

聚芴类发光材料合成中间体的质谱分析

利用电喷雾电离（ESI）质谱－质谱（MS－MS）技术，分析了新化合物2，7－双（4，4，5，5－四甲基－1，3，2－二氧杂硼烷－2－基）－9，9－二辛基芴的EI和ESI的质谱，确认了该谱图中母离子和子离子的关系，讨论了其碎裂途径，为其结构鉴定提供了依据。     

残留凝胶对聚辛基芴薄膜光致发光性能的影响

用荧光光谱、紫外可见吸收光谱、原子力显微镜表征了在55℃的条件下分别溶解12min、30min、80min的聚辛基芴甲苯溶液通过旋涂法制备的薄膜。结果表明用溶解时间较短的条件制备的薄膜内有平均尺寸约为120nm×80nm的凝胶团,这使荧光光谱呈现部分卢相发光。当溶解时间增长后薄膜完全呈现非晶相发光,薄膜内部凝胶团消失。...     

桥联二芴基稀土氯化物的合成及表征

用二（9－芴基）二甲基硅烷（Me2SiFlu2）的双锂盐与三氯稀土在室下反应合成了5个通式为Me2SiFlu2LnCl(Ln=Yb,Sm,La,Pr,Nd）的桥联二芴基稀土氯化物，所有配合物均经元素分析、IR，MS和^1H NMR表征。     

Synthesis,Structures and Photophysical Properties of Cationic Cyclometalated Iridium(III) Complexes Bearing N-Phenylcarbazole Group

Four cationic cyclometalated Ir^III complexes [(MeOPCz)₂Ir(bpy)]PF₆ ( 3 ), [(MeOPCz)₂Ir(dtb-bpy)]PF₆ ( 4 ), [(TFPCz)₂Ir(bpy)]PF₆ ( 5 ), and [(TFPCz)₂Ir(dtb-bpy)]PF₆ ( 6 ) were successfully synthesized using two new cyclometalated ligands 9-phenyl-3-(4-methoxypyridin-2-yl)-9H-carbazole (MeOPCz) 1 and 9-phenyl-3-(4-trifluoromethylpyridin-2-yl)-9H-carbazole (TFPCz) 2 in combination with 2,2'-bipyridine (bpy) and 4,4'-di-tert-butyl-2,2'-bipyridine (dtb-bpy) as ancillary ligands. These complexes adopt the distorted octahedral configuration, and the complexes 5 and 6 crystallize in the centrosymmetric space group C2/c. Emission wavelength of these complexes can be tuned from 583 nm to 628 nm by the substituents (methoxy, trifluoromethyl and tert-butyl groups) in ligands. All of these complexes show relatively high emission efficiencies (0.28–0.41) and short lifetimes (0.242–0.461 μs).     

Luminescent lanthanide complexes with 4-acetamidobenzoate: Synthesis, supramolecular assembly via hydrogen bonds, crystal structures and photoluminescence

Four new luminescent complexes, namely, [Eu(aba)₂(NO₃)(C₂H₅OH)₂] (1), [Eu(aba)₃(H₂O)₂]·0.5 (4, 4′-bpy)·2H₂O (2), [Eu₂(aba)₄(2, 2′-bpy)₂(NO₃)₂]·4H₂O (3) and [Tb₂(aba)₄(phen)₂(NO₃)₂]·2C₂H₅OH (4) were obtained by treating Ln(NO₃)₃·6H₂O and 4-acetamidobenzoic acid (Haba) with different coligands (4, 4′-bpy=4, 4′-bipyridine, 2, 2′-bpy=2, 2′-bipyridine, and phen=1, 10-phenanthroline). They exhibit 1D chains (1-2) and dimeric structures (3-4), respectively. This structural variation is mainly attributed to the change of coligands and various coordination modes of aba molecules. Moreover, the coordination units are further connected via hydrogen bonds to form 2D even 3D supramolecular networks. These complexes show characteristic emissions in the visible region at room temperature. In addition, thermal behaviors of four complexes have been investigated under air atmosphere. The relationship between the structures and physical properties has been discussed.     

Sm(DBM)3phen的光致发光和电致发光性质

制备了一系列基于配合物Sm(DBM)3phen的电致发光器件. 研究了其光致发光(PL)和电致发光(EL)性质, 实验结果表明, Sm(DBM)3phen具有良好的电子注入和传输性能以及电致发光性能. 器件ITO/TPD(50 nm)/Sm(DBM)3phen(50 nm)/Alq3(30 nm)/LiF(1.0 nm)/Al的最大亮度和最大效率分别为150 cd/m2和0.72 cd/A, 器件表现为纯Sm3+离子的发光.     

Theoretical Investigation on the Luminescent Properties of Polyfluorene and Poly（fluorene-co-thiophene）

The density functional theory was employed to study the structures, ionization potentials(IPs), electron affinities(EAs), and HOMO-LUMO gaps(ΔH-L) of the oligomers. The time-dependent density functional theory(TD-DFT) and ZINDO were employed to study the lowest excitation energies(Egs) and the absorption and emission spectra of the oligomers of polyfluorene(PF) and poly(fluorene-co-thiophene)(PFT). By extrapolating ΔH-L and Egs to those of infinite chain length, band gaps and effective conjugation lengths o...     

咔唑基四苯乙烯多功能发光材料的合成与性能

设计合成了一个以四苯乙烯为核心,四端连接长烷基链的咔唑基四苯乙烯衍生物(TPECz),该化合物具有典型的聚集诱导发光(AIE)特性.紫外光谱(UV-Vis)、荧光光谱(PL)、热重(TG)和示差扫描量热(DSC)研究表明,该化合物属于深蓝光材料、具有较好的热稳定性,并且对金属Fe3+具有很好的识别作用,有望用于金属离子检测;同时,该化合物外围的咔唑基团具有电化学活性,采用电化学聚合方法可制备其聚合物交联荧光薄膜,扫描电镜(SEM)和原子力显微镜(AFM)研究表明,该荧光薄膜表面平整,有望用于制备有机电致发光器件(OLED),可见该化合物是一种多功能材料.     

三苯胺-芴类共聚物的合成及发光性能

在主链上嵌入三苯胺基团来改善聚芴的空穴传输能力、平衡载流子的注入是目前改善聚芴材料发光效率的一种好方法。本文用Suzuki缩聚法合成了芴-三苯胺类共聚物。实验结果表明．在聚芴主链上引入少量的TPA(10％～20％)时．不仅提高了EL效率．而且可以改善光谱的色纯度。TPA含量为20％时,共聚物的EL效率为1．28％。     

新型吡唑啉酮稀土配合物的合成及荧光性能

通过分子设计,以吡啶-2,6-二甲酸为起始原料,合成了一种新型双吡唑啉酮吡啶配体:2,6-二(1-苯基4-乙氧羰基-5-吡唑啉酮-3-基)吡啶(H2L)。配体与稀土Eu(Ⅲ)和Tb(Ⅲ)离子成功螯合形成配合物。配体和配合物经FT-IR,1H NMR和元素分析进行表征,并确定配合物组成为RE2L3.4H2O。对配合物的紫外吸收和光致发光性能进行了检测,结果显示Eu(Ⅲ)和Tb(Ⅲ)离子能够有效地被有机配体敏化,发射出高亮、半峰宽狭窄的单色光。研究表明目标配合物能够成为优秀的发光材料。     

Synthesis, characterization and photophysics of fluorene-alt-oxadiazole copolymers containing pendent iridium (III) complex moiety

A series of fluorene-alt-oxadiazole copolymers containing a pendent phosphor chromophore of the (piq)₂Ir(pic) complex were synthesized via the palladium-catalyzed Suzuki coupling reaction, where piq is 1-phenylisoquinoline and pic is picolinic acid. These copolymers exhibited a similar absorption spectrum with a peak at about 330 nm and a typical emission peak at 408 nm in CH₂Cl₂ from the fluorene-alt-oxadiazole backbone. However, a significantly red-shifted emission peak at about 625 nm was observed in the neat films of these copolymers, which are attributed to the pendent iridium (III) complex unit. Using these copolymers as single emission layer, the polymer light-emitting devices with a configuration of ITO/PEDOT:PSS/copolymers/LiF/Al exhibited a saturated red emission with a peak at 632 nm. Significant influence of the attached iridium (III) complex ratio on EL performance was presented. A maximum current efficiency of 1.2 cd/A at 63 mA/cm² and a maximum luminance of 1125 cd/m² at 12 V were achieved from the device with the copolymer containing iridium (III) complex in a 3% molar ratio.     

Phosphine (oxide)‐(thio) phenolate palladium complexes: Synthesis,characterization and (co)polymerization of norbornene

A series of palladium complexes ( 2a–2g ) ( 2a : [6‐^tBu‐2‐PPh₂‐C₆H₃O]PdMe(Py); 2b : [6‐C₆F₅–2‐PPh₂‐C₆H₃O]PdMe(Py); 2c : [6‐^tBu‐2‐PPh^tBu‐C₆H₃O]PdMe(Py); 2d : [2‐PPh^tBu‐C₆H₄O] PdMe(Py); 2e : [6‐SiMe₃–2‐PPh₂‐C₆H₃O]PdMe(Py); 2f : [2‐^tBu‐6‐(Ph₂P=O)‐C₆H₃O]PdMe(Py); 2g : [6‐SiMe₃–2‐(Ph₂P=O)‐C₆H₃S]PdMe(Py)) bearing phosphine (oxide)‐(thio) phenolate ligand have been efficiently synthesized and characterized. The solid‐state structures of complexes 2d , 2f and 2g have been further confirmed by single‐crystal X‐ray diffraction, which revealed a square‐planar geometry of palladium center. In the presence of B(C₆F₅)₃, these complexes can be used as catalysts to polymerize norbornene (NB) with relatively high yields, producing vinyl‐addition polymers. Interestingly, 2a /B(C₆F₅)₃ system catalyzed the polymerization of NB in living polymerization manner at high temperature (polydispersity index 1.07, M_n up to 1.5 × 10⁴). The co‐polymerization of NB and polar monomers was also studied using catalysts 2a and 2f . All the obtained co‐polymers could dissolve in common solvent.