辐射交联制备改性CMC水凝胶的溶胀行为研究

利用丙烯酰胺 (AAm)接枝改性纤维素 ,然后进行羧甲基化反应得到高取代度的丙烯酰胺 羧甲基纤维素钠 (AAm CMC Na) .对该材料进行γ射线辐照制备出新型改性CMC水凝胶 .研究了这种水凝胶的溶胀动力学、交联动力学以及温度、pH值和无机盐浓度对水凝胶溶胀行为的影响 ,并与CMC Na水凝胶进行了比较 .结果表明 ,该水凝胶和CMC Na水凝胶相比 ,优点在于辐照交联所用的剂量下降 ,而且所需的CMC浓度减少 .AAm CMC Na水凝胶的溶胀度随温度升高而增大 ,在pH为 6～ 8范围内达到最大值 ,并随无机盐浓度与吸收剂量增加而下降 ,表现出较好的温度敏感性和pH敏感性 ,可望作为吸水材料和水保持剂     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

含水状态对细菌纤维素/聚苯胺复合凝胶膜制备及性能的影响

以不同含水量细菌纤维素为模板,苯胺单体为原料原位聚合生成聚苯胺,制备出不同含水量细菌纤维素/聚苯胺(HBC/PANI、LBC/PANI及DBC/PANI)复合凝胶膜,系统研究了细菌纤维素凝胶膜含水量和反应时间对苯胺原位聚合以及复合凝胶膜微观形貌、电学性能和力学性能的影响.扫描电镜照片表明聚苯胺均匀包覆在BC纤维上形成导电网络结构;四探针测试表明聚合时间90 min时导电率最高;低含水量加快了聚合反应速度,提高了复合凝胶膜的电导率,而完全干燥则使电导率降低;交流阻抗测试也表明低含水量可以明显提高材料的离子导电性;力学性能测试结果表明了BC/PANI复合凝胶膜具有良好的机械性能,抗拉强度可达0.21 MPa,同时低含水量不会降低复合凝胶膜的力学性能.     

pH敏感的聚(L-谷氨酸)-交联聚丙烯酸水凝胶的合成与性能研究

通过在聚L-谷氨酸侧链部分接枝甲基丙烯酸2-羟乙酯得到含有双键的聚(L-谷氨酸),将其与丙烯酸共聚得到由聚(L-谷氨酸)侧链接枝并交联聚丙烯酸的pH敏感水凝胶.研究水凝胶在不同pH的缓冲溶液中的溶胀性、溶胀动力学,并通过SEM观察水凝胶的微观结构.结果表明,水凝胶在低pH环境下的溶胀率明显低于高pH环境中的溶胀率,不同...     

k-型卡拉胶/聚乙烯吡咯烷酮共混水凝胶的辐射制备及性质研究

采用辐射技术制备了κ-型卡拉胶(KC)/聚乙烯基吡咯烷酮(PVP)共混水凝胶,研究了共混凝胶内KC含量、PVP的分子量和辐照剂量等对KC/PVP共混水凝胶性质的影响.实验发现,KC与高分子量的PVP(k-90)共混后在一定剂量范围内辐照可得到高强度、高溶胀行为的KC/PVP共混水凝胶,随着共混凝胶内KC含量的增加,凝胶强度及溶胀性能均显著提高.分析表明,KC与高分子量的PVP共混后,在较低剂量下KC的降解被抑制,从而获得一种由物理交联的KC和化学交联的PVP形成的互穿网络(IPN)凝胶.     

κ-型卡拉胶/聚乙烯吡咯烷酮共混水凝胶的辐射制备及性质研究

采用辐射技术制备了κ-型卡拉胶 ( KC) /聚乙烯基吡咯烷酮 ( PVP)共混水凝胶 ,研究了共混凝胶内 KC含量、PVP的分子量和辐照剂量等对 KC/ PVP共混水凝胶性质的影响 .实验发现 ,KC与高分子量的 PVP( k-90 )共混后在一定剂量范围内辐照可得到高强度、高溶胀行为的 KC/ PVP共混水凝胶 ,随着共混凝胶内KC含量的增加 ,凝胶强度及溶胀性能均显著提高 .分析表明 ,KC与高分子量的 PVP共混后 ,在较低剂量下 KC的降解被抑制 ,从而获得一种由物理交联的 KC和化学交联的 PVP形成的互穿网络 ( IPN)凝胶 .     

温度敏感水凝胶包覆长周期光纤光栅传感器研究

以N-异丙基丙烯酰胺(NIPAM)为单体、N,N'-亚甲基双丙烯酰胺(MBAA)为交联剂、安息香二甲醚(DMPA)为引发剂,利用紫外光引发聚合制备了一系列温度敏感性聚(N-异丙基丙烯酰胺)(PNIPAM)水凝胶,并对其性能进行了测定.结果表明,PNIPAM水凝胶的平衡膨胀比随着交联程度的变化而改变.当交联程度适当时,水凝胶可具有最大的溶胀比.在此研究基础上,利用浸渍提拉法在长周期光纤光栅(LPFG)包层外制备了PNIPAM水凝胶薄膜包覆层.研究了得到的LPFG传感器对温度和湿度的响应性,该类型传感器表现出对温度的灵敏响应性.     

PANI导电水凝胶的制备及其进展

导电水凝胶结合了水凝胶和导电高分子电性能的独特特性,并且具有特殊三维网络结构。其中聚苯胺(PANI)由于其独特的导电性能得到了广泛应用,因此PANI导电水凝胶是导电水凝胶中研究最为广泛的。本文综述了PANI导电水凝胶的制备方法及其发展,详述了PANI导电水凝胶的四种制备方法:直接填充、原位聚合、化学交联和物理交联。其中,利用直接填充和原位聚合方法制得PANI水凝胶是较传统的方法,获得的PANI水凝胶是由绝缘的水凝胶组分和导电的PNAI组分组合在一起,电化学性能不高。化学交联法的应用提高了导电水凝胶的电化学性能,物理交联法应用较少。最后,对导电水凝胶材料的应用以及未来发展方向进行了展望。     

会变形的水凝胶

本实验是关于可变形水凝胶的制备及其复杂形变的设计和调控的新创综合实验。首先,利用自由基聚合交联法制备含有聚丙烯酸钠(PNaAAc)的聚乙烯基吡咯烷酮-聚丙烯酰胺(PVP-PAAm)水凝胶。该凝胶具有优良的力学性能,其中PNaAAc可与Fe3+等金属离子络合,从而增加水凝胶的交联密度,降低其溶胀程度。使用离子转移印花技术和新开发的离子墨水打印技术在凝胶单面或双面不同位置引入Fe3+交联,改变水凝胶局部表面的交联密度和溶胀性能。处理后的凝胶样品在溶胀或去溶胀时可发生由一维到二维、二维到三维以及简单三维到复杂三维的复杂可控形变。     

聚(N-异丙基丙烯酰胺)/聚丙烯酰胺无机/有机互穿网络水凝胶的制备及表征

通过紫外引发聚合方法制备了无机交联的聚(N-异丙基丙烯酰胺)(PNIPAAm)/有机交联的聚丙烯酰胺(PAAm)互穿网络(IPN)水凝胶.利用FTIR和SEM分别表征了凝胶的化学结构和内部形态;测定了凝胶在高温(50℃)时的退溶胀性能;利用DMA和DSC分别研究了凝胶的储能模量随温度的变化及热相转变行为.研究表明,该IPN凝胶具有温度敏感性;与未互穿的无机交联PNIPAAm凝胶相比,IPN凝胶具有多孔的网络结构和超快的响应速率,如10min内失去90%的水;其储能模量增加了3～4倍,相转变行为变弱,而最低临界溶解温度(LCST)提高了1.4℃.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。