钙离子诱导的海藻酸钠/黄原胶凝胶化临界行为研究

研究了海藻酸钠/黄原胶混合体系的相行为及其对海藻酸钠-钙离子凝胶化临界行为的影响.当海藻酸钠浓度为0.5 wt%时,随着黄原胶的添加,混合体系出现相容、相分离及液晶3种不同的相行为.与纯黄原胶溶液相比,海藻酸钠/黄原胶混合溶液在更低的黄原胶浓度下开始形成液晶,这是由于混合体系中相分离的发生导致了黄原胶有效浓度升高.利用葡萄糖酸内酯(GDL)在线酸化Ca-EDTA,释放钙离子,研究了不同钙离子引入量时(f=[Ca2+]/[COO-])混合体系的黏弹性.Winter-Chambon分析发现临界凝胶点(f gel)随黄原胶浓度的增加而降低.当相分离发生时,临界凝胶点急剧降低,当液晶结构形成后,临界凝胶点呈现上升趋势.通过对比Winter-Chambon方法和临界凝胶点模量松弛法所测得的松弛临界指数(nw和nr),发现黄原胶的添加使海藻酸钠临界凝胶失去结构自相似性.相分离的发生导致临界凝胶结构排列更加致密,而液晶的出现使临界凝胶结构排列相对疏松.     

钛硅分子筛/H2O2 体系催化合成丁酮肟的反应行为

 钛硅分子筛/H2O2 体系催化酮氨肟化反应合成肟的过程中, 产物肟的反应行为直接影响氨肟化过程的反应效率和操作稳定性. 在 Ti-MWW/H2O2 体系催化丁酮氨肟化反应中研究了产物丁酮肟的反应行为, 发现 Ti-MWW 和 H2O2 的共同作用促使丁酮肟发生水解, 生成丁酮和氮氧化物, 使得反应体系从碱性变成了酸性. TS-1/H2O2 体系及产物环己酮肟均存在类似的现象.     

SDS对PEO-PPO-PEO嵌段共聚物溶液行为的影响

对PEO-PPO-PEO（127）三嵌段共聚物的水溶液行为及添加十二烷基硫酸钠（SDS）后对共聚物溶液行为的影响进行了研究．利用荧光探针技术对不同SDS浓度下F127／SDS体系的胶来形成进行研究,并研究了SDS对F127浓溶液凝胶化行为的影响．结果表明：随着SDS浓度的增大,F127稀溶液胶束的形成受到抑制,SDS浓度愈大,形成的胶束结构就愈疏松．对F127浓溶液来说,SDS与F127摩尔比小于2时,体系易于凝胶化;但当SDS浓度增大,其与F127摩尔比大于2时,体系开始难于凝胶化,直至摩尔比大于5时,体系不再形成凝胶．     

聚酰亚胺/聚丙烯腈共混黑膜的制备及其结构与性能

采用共混的方法制备聚酰胺酸/聚丙烯腈(PAA/PAN)共混溶液.其中2种PAA溶液分别由二酐(3,3′,4,4′-联苯二酐(BPDA)与均苯四甲酸二酐(PMDA))和二胺(对苯二胺(PDA)与4,4′-二氨基二苯醚(ODA))均聚或共聚而得,N,N-二甲基乙酰胺(DMAc)为溶剂,PAN溶于DMAc中制成溶液后与PAA溶液混合,涂膜后热处理制得聚酰亚胺(PI)/PAN共混薄膜.分析了PAA和PAN在热处理过程中的变化,以及PAN的加入量对共混薄膜的结构与性能的影响.结果表明,在热处理过程中,PAA完成了亚胺化成为PI,而PAN完成了预氧化,形成了稳定的梯形结构,制备出具有良好力学性能、黑色、不透光的薄膜,但是随着PAN含量的增加,体系发生明显的相分离,薄膜力学性能有所下降,(BPDA/PDA/ODA)PI中加入10%的PAN和(PMDA/ODA)PI中加入20%的PAN时能获得具有良好力学性能的黑色、低透光率的薄膜.     

MnCl2/DMSO溶液的拉曼光谱和理论计算

利用拉曼光谱研究了不同温度和浓度MnCl₂/DMSO溶液体系离子的溶剂化作用, 结果表明, 在0~0.8 mol/L浓度范围内, 随着浓度增加, Mn²⁺与DMSO的相互作用逐渐增强, S=O伸缩振动峰向低波数移动, S=O双键减弱; C—S伸缩振动峰向高波数移动, C—S键增强. 温度升高, S=O双键和C—S键伸缩振动峰均向相反的方向移动, 溶剂化作用减弱. 56 ℃以上, 单体DMSO迅速增加, 与Mn²⁺溶剂化作用的DMSO迅速减少, 二聚体DMSO减少缓慢, 温度对溶剂化作用的影响大于溶剂自身的缔合. 利用密度泛函理论对可能存在的溶剂化构型[Mn(DMSO)_n]²⁺进行了优化、 热力学性质及理论拉曼光谱计算, 从理论上证实了Mn²⁺与DMSO存在相互作用, 导致DMSO的S=O键拉伸和C—S键收缩, 与实验光谱结果一致.     

聚丙烯腈基碳纤维的组织结构演变过程研究

用丙烯腈（AN）、衣糠酸（IA）、丙烯酸甲酯（MA）进行三元自由基溶液共聚合，经湿法纺丝制得聚丙烯腈（PAN）原丝，然后进行预氧化和碳化处理，并用SEM和TEM等分析方法跟踪过程中纤维微观结构的变化。结果表明：碳纤维的微观组织结构与原丝的微观组织结构密切相关，高强度、高取向度、结构均匀和弥散性好的原丝是获得高强度和高模量碳纤维的前提。     

高效液相色谱法测定聚丙烯腈基碳纤维原丝中的二甲基亚砜残留

建立了聚丙烯腈（PAN）基碳纤维原丝中二甲基亚砜（DMSO）残留量的高效液相色谱（HPLC）检测方法。采用的色谱柱为Phenomenex C18柱（150 mm×4.6 mm,5 μm）,流动相为甲醇-三氟乙酸-水（体积比为29∶1∶70）混合溶液,流速为1.0 mL/min,进样量为10 μL,检测波长为205 nm,柱温为常温。研究结果表明,在DMSO的质量浓度为1.00~100.00 mg/L范围内,峰面积与质量浓度的线性关系良好,相关系数r=0.9989,最低检出限为0.3 mg/L,平均回收率为98.4%,相对标准偏差（RSD）为2.6%。该方法简便、快速、准确。另外,利用建立的HPLC方法,对原丝中残留的DMSO在水中的溶出规律也进行了研究。     

丙烯腈与衣康酸在DMSO/H_2O中的聚合及聚合物性能表征

采用丙烯腈 (AN)与衣康酸 (IA)为共聚单体 ,以偶氮二异丁腈为引发剂在混合介质二甲基亚砜 水(DMSO H2 O)中自由基沉淀共聚合 ,合成了高分子量的聚丙烯腈 .通过正交设计方法研究了聚合反应条件 ,如反应温度、单体浓度、混合介质DMSO H2 O配比等对聚合反应的转化率的影响 ,还重点探讨了混合介质DMSO H2 O配比对转化率和粘均分子量的影响 .采用DSC ,TG ,IR等手段研究了PAN均聚物及 (PAN co IA)的结构与性能 .研究结果表明 ,增加反应温度 ,降低单体浓度 ,降低喂料AN IA配比中IA的含量 ,均有利于提高聚合反应的转化率 .AN与IA共聚反应的转化率随着反应介质中DMSO含量的增加而降低 ,同时聚合物的粘均分子量也降低 .对于喂料AN IA配比中IA含量相同的P(AN co IA)共聚物 ,高分子量P(AN co IA)共聚物比常规低分子量的放热峰起始温度低 ,放热峰宽     

聚甲基丙烯酸甲酯/聚醋酸乙烯酯/纳米二氧化硅体系的相分离行为研究

研究了聚甲基丙烯酸甲酯/聚醋酸乙烯酯/纳米二氧化硅(PMMA/PVAc/silica)体系的相分离行为.通过傅里叶变换红外光谱和链缠结行为的研究发现PMMA和PVAc间存在较强的分子间相互作用,加入纳米二氧化硅导致2种聚合物在纳米粒子表面吸附,从而改变了分子间相互作用.体系中复杂的分子间相互作用以及纳米粒子-聚合物相互作用使得时温叠加严重失效,因此提出用归一化Cole-Cole图分析该体系的相分离过程.纳米粒子对不同组成体系相分离行为的影响不同,近临界组成中纳米粒子促进相分离并最终分布于两相界面,远临界组成中纳米粒子起成核作用并始终分布于海岛相中,这种由相分离机理决定的纳米粒子选择性分布为调控纳米粒子在聚合物中的组装结构提供了新的思路.     

高取向度碳纤维原丝制备工艺研究进展

碳纤维原丝的性能好坏在很大程度上决定着碳纤维的最终性能。缺陷少、细旦化、高取向、高纯化等是高性能原丝的基本要求。其中原丝的取向度在很大程度上决定了碳纤维在预氧化、碳化过程中形成的类石墨片层的取向结构，这会影响碳纤维最终的强度和模量，所以制备出高取向的碳纤维原丝具有重大意义。本文聚焦于高取向碳纤维原丝制备工艺，首先分析了高取向原丝的重要性，然后在原丝制备工艺上将纺丝方法以及牵伸工艺对取向度的影响进行总结分析，同时介绍了微积分纳米层叠法和高取向复合纤维原丝的制备工艺，指出优质的初生纤维以及具有稳定化取向排列的原丝是制备高取向碳纤维原丝的关键，以期对提升原丝的取向度进而提升碳纤维性能的研究有所贡献。     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.     

Synthesis and properties of the Co7Se8−xSx and Ni7Se8−xSx solid solutions

We report the synthesis and elementary properties of the Co₇Se_8−xS_x (x=0-8) and Ni₇Se_8−xS_x (x=0-7) solid solutions. Both systems form a NiAs-type structure with metal vacancies. In general, the lattice parameters decrease with increasing x, but in the Ni₇Se_8−xS_x system c increases on going from x=5 to 7. Magnetic susceptibility measurements show that all samples exhibit temperature-independent paramagnetism from 25-250 K. Samples within the Co₇Se_8−xS_x system, as well as Ni₇Se₈ and Ni₇SeS₇, were found to be poor metals with resistivities of ∼0.20 and ∼0.06 mΩ cm at 300 K, respectively. The Sommerfeld constant (γ) was determined from specific heat measurements to be ∼13 mJ/mol_CoK² and ∼7 mJ/mol_NiK² for Co₇Se_8−xS_x and Ni₇Se_8−xS_x, respectively.     

Electronic and magnetic properties of LaNi1−xCoxO3, LaCo1−xFexO3 and LaNi1−xFexO3

LaNi_1?xCo_xO₃ shows itinerant d-electron behavior similar to LaNiO₃ up to x = 0.5. In the range 0.5 < x < 1.0, the cobalt spin state equilibrium is markedly affected; the localized-itinerant electron transition of LaCoO₃ is not seen when x < 0.95. In LaCo_1?xFe_xO₃, itinerancy of d-electrons decreases with increase in x and the compositions with x > 0.5 are similar to LaFeO₃. If x > 0.1, the localized-itinerant electron transition is not seen and the cobalt spin state equilibrium is considerably altered. In LaNi_1?xFe_xO₃, itinerancy decreases with increase in x. These observations can be satisfactorily explained in terms of Goodenough's energy band schemes.     

Separation of Th/IV/ and U/VI/ by extraction chromatography

Application of extraction chromatographic technique to the analytical separation of Th/IV/ and U/VI/ has been investigated. The stationary phase was a macroporous resin Amberlite XE-270 impregnated with undiluted trin-n-butylphosphate /TBP/ and the mobile phase was either 5.OM HNO₃ or 6M HCl. Separation of traces of Th/IV/ from large quantities of U/VI/ was achieved on a laboratory column by elution of the absorbed Th/IV/ with 6M HCl.     

Rate of reactions between D2O and CaxAlyOz

The rate of the reaction between D₂O and the calcium aluminum oxides Ca₃Al₂O₆, Ca₅Al₆O₁₄, CaAl₂O₄, and CaAl₄O₇ was investigated by on-line neutron diffraction powder methods at temperatures from room temperature to 100°C. The rate of the reaction increases with increasing calcium content of the compounds and with increasing temperature for each of the compounds. The crystallographic stable hydrate Ca₃Al₂(OD)₁₂ is obtained from CaAl₄O₇ and CaAl₂O₄ at temperatures above 63°C, from Ca₅Al₆O₁₄ at temperatures above 49°C, and from Ca₃Al₂O₆ at temperatures as low as 7°C.