四乙基氢氧化铵改性聚偏氟乙烯接枝聚丙烯酸油水分离膜的制备

使用四乙基氢氧化铵(TEAH)液相本体改性聚偏氟乙烯(PVDF), 以过氧化苯甲酰(BPO)为引发剂, 将丙烯酸(AA)接枝到改性PVDF骨架上, 合成了聚偏氟乙烯接枝聚丙烯酸(PVDF-g-PAA)共聚物, 通过浸没沉淀法制备了PVDF-g-PAA亲水性油水分离膜. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)和过滤试验分析了膜的结构和分离性能. 研究了不同接枝条件对PVDF-g-PAA膜接枝率的影响. 同时, 通过膜接枝率与膜表面接触角的关系确定最佳接枝条件. 结果表明, TEAH使PVDF脱去HF产生碳碳双键且PAA接枝到改性的PVDF骨架上, 膜内外孔隙分布均匀; PVDF-g-PAA膜的接触角随着接枝率的提高而降低. 接枝单体AA含量为45%, 接枝温度为85 ℃, 接枝4 h制备的PVDF-g-PAA膜的接枝率为20.1%, 孔隙度为65.3%, 平均孔径为78.0 nm, 接触角为57.5°, 且在60 s内接触角降至14.3°; 纯水通量提高到571.33 L/(m²·h), 截留率和水通量恢复率分别达到94.3%和88.7%, 且通量衰减率仅为9.8%. 与纯PVDF膜相比, PVDF-g-PAA膜的分离性能显著提高.     

四甲基氢氧化铵改性聚偏氟乙烯一步接枝聚苯乙烯磺酸油水分离膜的制备及性能

利用四甲基氢氧化铵(TMAH)聚偏氟乙烯(PVDF)进行改性,以过氧化苯甲酰(BPO)为引发剂,将苯乙烯磺酸(SSA)接枝到改性的PVDF骨架上,制得聚偏氟乙烯接枝聚苯乙烯磺酸(PSSA-g-PVDF)油水分离膜。 研究了TMAH质量分数对PSSA的接枝率和油水分离膜性能的影响,同时采用傅立叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)和视频光学接触角测量仪测试了膜的结构和表面接触角。 结果表明,TMAH使PVDF脱去部分氟化氢(HF)产生碳碳双键,硫元素均匀地分布在分离膜中。 PSSA的接枝率随着TMAH的质量分数增加而升高,分离膜的水通量随接枝率的升高先增加后降低。 当TMAH质量分数为20%,分离膜的接触角在30 s内降低到37.2°,接枝率和水通量分别为22.1%、643.3 L/(m·h),截留率和水通量恢复率分别达到90.6%和93.7%,衰减率为7.1%。 循环测试显示膜的水通量恢复率和油水通量恢复率均在90%以上。     

甲基丙烯酸甲酯在聚偏氟乙烯膜上的辐照接枝

采用电子加速器(EB)预辐照接枝的方法,在聚偏氟乙烯(PVDF)膜上接枝甲基丙烯酸甲酯(MMA),制备了PVDF-g-PMMA膜。研究了辐照剂量、单体浓度、反应温度、反应时间以及溶剂等因素对接枝率的影响规律。结果表明,接枝率随辐照剂量的增大而增加;反应初期接枝率随着单体质量分数的增大迅速增加,当单体质量分数达40%时,增加缓慢;单体质量分数达70%时,接枝率最高;从40℃开始接枝率缓慢上升,至60℃时陡增,之后接枝率基本不变;醇类是接枝反应很好的溶剂。用FT-IR、DSC分析了接枝物的组成及热性能。接枝膜成分为PVDF-g-PMMA共聚物,接枝膜在117℃处出现Tg峰,随着接枝率的增加该峰越来越明显,说明发生了接枝反应。随着接枝率的增加,熔融峰左移并最终消失,说明PMMA的接枝破坏了原PVDF膜的结晶性。吸液率随着浸泡时间的增加而增大,PVDF接枝膜达到的最大吸液率为290%,所需要的时间比原PVDF膜长。接枝率为50%的PVDF膜的离子电导率为6.0×10-3S/cm,吸液率达290%,MMA的接枝改善了PVDF电解质膜的电学性能。     

TMAH改性PVDF一步接枝PSBMA质子交换膜的制备与性能

使用四甲基氢氧化铵(TMAH)液相改性聚偏氟乙烯(PVDF),以过氧化苯甲酰(BPO)为引发剂,一步将磺酸基甲基丙烯酸甲酯(SBMA)接枝到改性的PVDF上,制备了聚偏氟乙烯接枝聚磺酸基甲基丙烯酸甲酯(PVDFg-PSBMA)质子交换膜.利用傅里叶变换红外(FTIR)光谱和扫描电镜-X射线能谱(SEM-EDX)分析了膜的结构、形貌及硫元素分布情况.同时研究了不同质量分数的TMAH甲醇溶液对PVDF-g-PSBMA膜电导率和甲醇渗透率的影响.结果表明, TMAH使PVDF脱去HF产生碳碳双键且SBMA成功接枝到改性的PVDF骨架上,硫元素在膜内外分布均匀; PVDF-g-PSBMA膜的电导率和甲醇渗透率随TMAH在甲醇中质量分数的增多而增大, TMAH质量分数为20%的膜的质子电导率在20 ℃下达到0.0892 S·cm^-1,常温下的甲醇渗透率为4.04 × 10^-7cm²·s^-1;热重分析(TGA)表明,膜的热稳定性良好,耐热温度高达270 ℃.该膜作为电解质材料的直接甲醇燃料电池(DMFC)的最大功率密度达到17.06 mW·cm^-2.     

超亲水聚偏氟乙烯中空纤维膜的制备及性能

采用超声辅助接枝聚合技术, 将甲基丙烯酸缩水甘油酯(GMA)接枝到聚偏氟乙烯(PVDF)膜表面, 制备PVDF-g-GMA膜; 再利用氨基诱导环氧基团发生开环反应, 将苏氨酸(Thr)接枝到PVDF-g-GMA膜表面, 制备了具有两性离子结构表面的PVDF-g-GMA-Thr膜. 通过衰减全反射傅里叶变换红外光谱(ATR-FTIR)、 X射线光电子能谱(XPS)、 接触角测试仪、 场发射扫描电子显微镜(FESEM)和牛血清白蛋白(BSA)过滤实验等系统研究了改性前后PVDF膜表面的化学组成、 润湿性能、 表面形貌和抗污染性能. 研究结果表明, 随着PVDF-g-GMA接枝Thr反应时间的增加, PVDF-g-GMA-Thr膜的亲水性能明显提高, 接触角从90°降为0°, 呈现出超亲水性能. 同时PVDF-g-GMA-Thr膜的水通量明显提高, 当Thr诱导开环反应时间为12 h时, PVDF-g-GMA-Thr膜的水通量高达686 L/(m ²·h), 与PVDF原膜相比, 水通量提高了204.5%. 在BSA的过滤测试中, 与PVDF膜相比, PVDF-g-GMA-Thr膜呈现出良好的截留性能和抗污染性能, BSA截留率从42%提高到84%,水通量恢复率从53%提高到87%, 不可逆污染率从47%降到12%, 表明通过接枝Thr构筑两性离子结构表面可以有效减小膜污染.     

四甲基氢氧化铵改性聚偏氟乙烯接枝苯乙烯磺化膜的制备和性能

使用四甲基氢氧化铵(TMAH)甲醇溶液在液相中改性聚偏氟乙烯(PVDF),挥发溶剂得到改性聚偏氟乙烯膜(g-PVDF-M),再以过氧化苯甲酰(BPO)为引发剂,将苯乙烯接枝到g-PVDF-M膜中,磺化后制得改性聚偏氟乙烯接枝苯乙烯磺化(PVDF-g-PSSA)膜.利用傅里叶变换红外光谱(FTIR)和能谱仪的扫描电子显微镜分析了PVDF-g-PSSA膜(TMAH-25)的结构、形貌及硫元素分布情况.通过电化学工作站和气相色谱仪研究了TMAH在甲醇中的不同含量对PVDF-g-PSSA膜质子电导率和甲醇渗透率的影响.结果表明,TMAH使PVDF脱去HF生成碳碳双键,并且苯乙烯接枝到改性的聚偏氟乙烯膜中,磺化后S元素在PVDF-g-PSSA膜内部均匀分布;PVDF-g-PSSA膜的质子电导率和甲醇渗透率随TMAH在甲醇溶液中质量分数的增加而增大;TMAH的质量分数为25%时,PVDF-g-PSSA膜的电导率达1.28×10~(-2)S/cm,甲醇渗透率为4.58×10~(-7)cm~2/s.热重分析(TGA)表明,PVDF-g-PSSA膜的热稳性良好,耐热温度高达195℃,PVDF-g-PSSA膜作为电解质材料的直接甲醇燃料单电池(DMFC)功率密度达到16.45 mW/cm~2.     

改性聚偏氟乙烯接枝磺化聚(苯乙烯-co-丙烯酸)膜的研制

以过氧化苯甲酰(BPO)作引发剂,通过溶液接枝聚合法把苯乙烯/丙烯酸同时接枝到原硅酸钠改性的聚偏氟乙烯(PVDF)膜上,磺化后得到聚偏氟乙烯接枝磺化聚(苯乙烯-co-丙烯酸)膜(PVDF-g-P(SSA-co-AA)).研究了苯乙烯和丙烯酸的不同比例对膜的接枝反应及其相对湿度对膜电导率和含水量的影响.用傅立叶变换红外光谱(FTIR)检测原硅酸钠改性的PVDF膜经过接枝和磺化后所发生的结构变化,并用扫描电镜(SEM)观察PVDF膜接枝前后的形貌以及接枝磺化后产物PVDF-g-P(SSA-co-AA)膜的形貌及硫和硅分布.结果表明,原硅酸钠改性的PVDF膜与苯乙烯/丙烯酸同时发生接枝聚合反应,环境的相对湿度在20%～80%范围,对添加10wt%Na4SiO4的PVDF-g-P(SSA-co-AA)膜的电导率的影响基本不变,并达到0.0198S·cm-1.原硅酸钠改性的PVDF膜结构在接枝前后和磺化前后发生变化,确认磺化反应不只是在膜表面,同时渗入膜中进行.     

表面引发的原子转移自由基聚合法在聚偏二氟乙烯表面制备可控的聚甲基丙烯酸甲酯刷

采用表面引发的原子转移自由基聚合法(ATRP)在聚偏二氟乙烯(PVDF)表面制备结构可控的聚甲基丙烯酸甲酯刷。通过碱处理和紫外光照溴代的方法,将ATRP引入到PVDF表面; 然后采用ATRP法将甲基丙烯酸甲酯接枝到溴代的PVDF表面。采用傅里叶变换红外光谱和X-射线光电子能谱对改性前后PVDF表面的结构进行了表征。结果表明甲基丙烯酸甲酯成功地接枝到了PVDF表面。     

碱处理PVDF膜对制备高电导率质子交换膜的作用

燃料电池是一种高能量密度、低污染的新型能源. 质子交换膜是燃料电池的核心组件之一. 在对聚偏氟乙烯(PVDF)膜进行了碱处理改性的基础上制备了高电导率的聚偏氟乙烯接枝聚苯乙烯磺酸(PVDF-g-PSSA)质子交换膜, 对碱处理后的PVDF膜进行了傅立叶变换红外光谱(FTIR)、傅立叶变换拉曼光谱(FT-Raman)及电子自旋共振(ESR)分析. 振动光谱显示在处理后的膜中存在共轭碳碳双键. 首次用ESR检测到碱处理后的PVDF膜中形成了自由基, 其浓度在10¹⁶ spin/g. 研究表明碱处理引起的膜结构变化有利于接枝反应的进行, 对提高所合成的质子交换膜的电导率有重要作用, 电导率提高一个数量级, 至6.40×10^－2 S/cm.     

碳纳米管对聚偏氟乙烯膜的共混改性研究

用相转化法制备了聚偏氟乙烯/碳纳米管共混膜,研究了共混膜的表面结构、水通量、孔隙率、接触角和机械性能。结果显示碳纳米管的加入提高了聚偏氟乙烯膜的亲水性和水通量,当聚偏氟乙烯浓度为10wt.%,碳纳米管含量为1.5wt.%时,共混膜的水通量和孔隙率最高,从243 L/m2·h和86.2%提高到365 L/m2·h和91.4%;接触角也由82°减小为67°;同时,共混膜的机械性能也得到显著提高。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.