碱催化促进Ni-W/β分子筛催化剂氢解纤维素产1,2-丙二醇的研究

为提高纤维素催化氢解产醇类产物中1,2-丙二醇(1,2-PG)的收率,采用等体积浸渍法制备了以β分子筛为载体负载Ni和W的催化剂。结果表明,当7Ni-20W/β分子筛作为催化剂时,在240℃反应温度和6.0 MPa H_2的条件下反应30 min后,纤维素实现完全转化,1,2-PG和乙二醇(EG)产率分别达到19.3%和45.3%;不同于其他载体催化剂,β分子筛可以明显提高1,2-PG选择性。当不同碱催化剂加入到Ni-W/β分子筛催化剂反应体系后,可以进一步提高1,2-PG的选择性。尤其是当加入Ba(OH)_2后,1,2-丙二醇产率从19.3%提高了32.5%。为了探究碱催化剂在反应中的作用,以葡萄糖为底物进行了一系列的碱催化反应。结果表明,碱催化剂主要作用是有助于将葡萄糖异构化为果糖,从而促进纤维素转化为1,2-PG。催化剂在两次回收重复利用之后1,2-PG的收率只下降3.9%,乙二醇产率收率下降4.1%。     

酸碱解聚玉米秸秆分子结构的实验研究

以玉米秸秆为研究对象,分别采用5%H2SO4和5%NaOH溶液对秸秆进行解聚处理,并对解聚前后秸秆结构、化学组成、热稳定性等进行分析和表征。结果表明,与未处理前相比,经酸或碱解聚处理后,秸秆纤维结晶度由51.8%分别提高到63.5%和67.0%,秸秆中大部分半纤维素和部分木质素组分被脱除,半纤维素由29.10%分别降至7.02%和6.86%,木质素由38.12%分别降至32.21%和16.52%,而纤维素则由31.54%分别升至60.54%和76.15%。经酸碱处理后,秸秆表面形态结构变得疏松,出现小孔和裂缝,降解温度达到350℃,热稳定性能增加。上述结果说明,稀酸或稀碱均对玉米秸秆分子结构有一定程度的解聚作用,但就解聚溶出木质素而言,稀碱的解聚溶出效果要优于稀酸的。     

复合酶耦合酶解酸处理后玉米秸秆的研究

以玉米秸秆为研究对象,经过2%硫酸预处理后,利用果胶酶、β-葡萄糖苷酶、纤维素酶三种酶协同酶解,以提高玉米秸秆的酶解产糖量。结果表明:当酶解时间为48h,果胶酶、β-葡萄糖苷酶、纤维素酶分别为45U/mL、30U/mL、60U/mL时,葡萄糖、木糖和酶水解得率分别为67.83%、3.25%、73.65%,相比纤维素酶单一酶解的葡萄糖、木糖和酶水解得率分别提高了65.04%、20.82%、65.06%。分步糖化发酵5天后,相比单一酶解发酵乙醇含量提高了72.5%。说明利用三种酶复合处理,能明显提高酶解产糖量。研究结果为玉米秸秆转化为可发酵糖技术的研究提供重要参考。     

碱解聚对玉米秸秆的影响

以玉米秸秆为研究对象,氢氧化钠为解聚剂,研究了碱解聚前后玉米秸秆组份、表面形态、化学官能团和纤维结晶度的变化。结果表明:玉米秸秆中木质素的主要组成单体是H-木质素,解聚液中的酚类物质有4-羟基苯甲醛、香草醛、紫丁香醛、对香豆酸和阿魏酸。玉米秸秆经碱解聚,表面形态变得疏松而多孔,红外光谱下木质素的特征吸收峰消失,85%的木质素和52%的半纤维素被脱除,而纤维素的相对含量增加,结晶度增大。说明碱解聚有利于后续酶解和(或)其它生化方法的实施,以实现秸秆纤维的高值转化。     

不同方法预处理的玉米秸秆结构与酶解分析

在利用秸秆进行工业转化时,因为秸秆结构复杂,导致转化效率低,所以需对秸秆进行预处理,破坏秸秆复杂结构,提高转化效率。采用扫描电镜(SEM)、傅里叶变换红外光谱(FT-IR)和X射线衍射技术分析不同预处理方式对玉米秸秆微观结构的影响,并利用纤维素酶对不同预处理秸秆进行酶解,评价预处理效果。扫描电镜结果表明,不同预处理方式对秸秆表面形态和秸秆整体结构造成不同程度的破坏,其中NaOH预处理后的秸秆表面结构坍塌明显,表明木质纤维素结构被有效打破。利用傅里叶变换红外光谱对不同预处理方式的秸秆进行分析,其中1600和1510cm~(-1)为木质素的特征峰,NaOH预处理后的秸秆在此处的特征峰基本消失,表明NaOH预处理对秸秆木质素的去除效率比较明显。1744~1734 cm~(-1)为C=O伸缩振动特征峰,此峰的强度与木质素和半纤维素的含量有关,采用不同方法预处理后,此峰的吸收强度不同程度地减少,表明各种预处理方法不同程度地去除了秸秆的木质素和半纤维素。X-射线衍射分析表明,不同预处理后秸秆的结晶度均发生不同程度的改变,其中H_2SO_4预处理后秸秆的结晶度提高最大,达到43.4%。其中NaOH预处理秸秆后,用纤维素酶酶解60h,使其酶解产糖量达到33.32g/L。本研究分析了不同秸秆预处理方法的效果,为利用玉米秸秆生产生物化工产品提供了理论依据。     

不同热裂解温度下ZSM-5对玉米秸秆催化热裂解烃类选择性影响

为探讨不同热裂解温度下ZSM-5对玉米秸秆催化热裂解特性及烃类选择性的影响,本研究利用TGA对比有无ZSM-5时玉米秸秆的热裂解失重曲线,利用Py-GC/MS对比玉米秸秆在450、500、550和600℃下的热裂解和催化热裂解产物分布。结果表明,ZSM-5的使用可以降低玉米秸秆最高分解速率时对应的热裂解温度,降低温度为23℃。未使用ZSM-5时,热裂解产物种类以及烃类选择性均随热裂解温度的升高不断增加,在600℃时,烃类选择性达到最高,为11.33%;使用ZSM-5后,烃类产率随热裂解温度的升高先增加后减少,在550℃时,烃类选择性达到最高,为29.24%。使用ZSM-5后,玉米秸秆催化热裂解主要产物中出现了甲苯、茚、萘、二甲基萘等烃类,甲苯的最高产率为4.76%,萘的最高产率为3.96%。     

Hydrogenolysis of Lignin Catalyzed by NaBH4/I2

从麦草碱法制浆黑液中提取木质素,精制后,以苯乙酮为木质素的模型化合物,对催化剂组成及溶剂进行了考察.在此基础上,以NaBH4/I2为催化剂,无水乙醇为溶剂,对木质素进行加氢还原裂解反应研究.考察了温度和时间对木质素催化加氢效果的影响,采用红外光谱（FTIR）、元素分析及凝胶渗透色谱分析（GPC）,表征木质素反应前后结构的变化.凝胶渗透色谱分析表明,加氢还原后木质素的分子量明显降低.采用自动电位滴定法测定反应前后木质素中总羟基含量,反应后木质素中总羟基含量为10.19%.得到了NaBH4/I2催化木质素加氢还原反应的最优条件：以1,2-二氯乙烷和乙醇（2∶1,v/v）作溶剂,m（NaBH4）∶m（I2）=1∶1,温度175℃,反应时间15 h.     

NaBH4/I2催化加氢还原碱木质素的研究

从麦草碱法制浆黑液中提取木质素,精制后,以苯乙酮为木质素的模型化合物,对催化剂组成及溶剂进行了考察.在此基础上,以NaBH4/I2为催化剂,无水乙醇为溶剂,对木质素进行加氢还原裂解反应研究.考察了温度和时间对木质素催化加氢效果的影响,采用红外光谱(FTIR)、元素分析及凝胶渗透色谱分析(GPC),表征木质素反应前后结构的变化.凝胶渗透色谱分析表明,加氢还原后木质素的分子量明显降低.采用自动电位滴定法测定反应前后木质素中总羟基含量,反应后木质素中总羟基含量为10.19%.得到了NaBH4/I2催化木质素加氢还原反应的最优条件:以1,2-二氯乙烷和乙醇(2∶1,v/v)作溶剂,m(NaBH4)∶m(I2)=1∶1,温度175℃,反应时间15 h.     

Cu催化羟基自由基氧化断裂纤维二糖分子糖苷键反应及其在纤维素低温解聚中的应用

纤维素是葡萄糖通过β-1,4-糖苷键链接而成的高聚物,在木质纤维素中含量最高,结构稳定,较难水解.糖苷键的解聚主要有三种方式:酶水解、酸水解以及碱降解.酶解的优点是反应条件温和、副产物少,但存在成本高、活性低等缺点,限制了其大规模的工业化生产.碱水解纤维素的同时伴随着葡萄糖的peeling-off反应得到异变糖酸,需要消耗大量的碱,并且强碱也存在腐蚀性强和回收难等问题.酸水解是目前工业上常用的纤维素水解方法,在保持较高葡萄糖选择性的同时,通过对反应条件的控制(提高反应温度和酸浓度)来提高纤维素的水解效率,但是硫酸对设备的腐蚀性强,也难以回收,不符合绿色化学的发展要求.固体酸是近年来研究较多的纤维素水解催化剂.固体酸虽然腐蚀性弱、易回收,但是其活性低,水热稳定性较差,目前还不具备大规模生产的条件.本文发展了一种羟基自由基活化断裂糖苷键的方法,利用羟基自由基的高活性在低温下实现糖苷键的选择性断裂,同时羟基自由基与糖苷键作用后转化为无毒无害的水和氧气,将不会对环境造成污染.我们首先以纤维二糖作为纤维素的模型分子,通过羟基自由基能够优先与糖苷键反应得到葡萄糖和葡萄糖酸的实验证实所提出的方法的可行性.实验表明,来自H2O2的·OH自由基能够在铜基催化剂作用下选择性氧化断裂其糖苷键,生成葡萄糖和葡萄糖酸.比如:采用均相CuSO4体系,纤维二糖转化率约为20%时,葡萄糖和葡萄糖酸的选择性分别为28.5%和32.3%.采用多相CuO/SiO2(4 wt%CuO)体系,纤维二糖转化率约为20%时,葡萄糖和葡萄糖酸的选择性约分别为23.3%和25.7%,并且该催化剂具有良好的循环使用性能.与·OH类似,CuSO4催化过硫酸钾生成的·SO4-自由基也能够有效转化纤维二糖,在纤维二糖转化率为20%时,葡萄糖和葡萄糖酸的选择性分别为36.6%和39.9%.利用这种·OH和·SO4-自由基氧化的方法,也能够在较低温度下(333 K)解聚纤维素中的糖苷键.我们发展了H2O2浸渍预处理纤维浸渍预处理纤维素的方法,通过部分破坏纤维素糖苷键,提高了纤维素的水解活性.比如:处理后的纤维素在413 K条件下反应12 h,纤维素转化率和葡萄糖选择性分别达到约36.1%和42.5%.XRD结果表明,处理后的纤维素的晶体结构未发生明显的变化.FT-IR表征结果显示处理后的纤维素表面生成了大量的羧酸基团.     

Cu催化羟基自由基氧化断裂纤维二糖分子糖苷键反应及其在纤维素低温解聚中的应用（英文）

纤维素是葡萄糖通过β-1,4-糖苷键链接而成的高聚物,在木质纤维素中含量最高,结构稳定,较难水解.糖苷键的解聚主要有三种方式:酶水解、酸水解以及碱降解.酶解的优点是反应条件温和、副产物少,但存在成本高、活性低等缺点,限制了其大规模的工业化生产.碱水解纤维素的同时伴随着葡萄糖的peeling-off反应得到异变糖酸,需要消耗大量的碱,并且强碱也存在腐蚀性强和回收难等问题.酸水解是目前工业上常用的纤维素水解方法,在保持较高葡萄糖选择性的同时,通过对反应条件的控制(提高反应温度和酸浓度)来提高纤维素的水解效率,但是硫酸对设备的腐蚀性强,也难以回收,不符合绿色化学的发展要求.固体酸是近年来研究较多的纤维素水解催化剂.固体酸虽然腐蚀性弱、易回收,但是其活性低,水热稳定性较差,目前还不具备大规模生产的条件.本文发展了一种羟基自由基活化断裂糖苷键的方法,利用羟基自由基的高活性在低温下实现糖苷键的选择性断裂,同时羟基自由基与糖苷键作用后转化为无毒无害的水和氧气,将不会对环境造成污染.我们首先以纤维二糖作为纤维素的模型分子,通过羟基自由基能够优先与糖苷键反应得到葡萄糖和葡萄糖酸的实验证实所提出的方法的可行性.实验表明,来自H_2O_2的·OH自由基能够在铜基催化剂作用下选择性氧化断裂其糖苷键,生成葡萄糖和葡萄糖酸.比如:采用均相Cu SO_4体系,纤维二糖转化率约为20%时,葡萄糖和葡萄糖酸的选择性分别为28.5%和32.3%.采用多相CuO/SiO_2(4 wt%CuO)体系,纤维二糖转化率约为20%时,葡萄糖和葡萄糖酸的选择性约分别为23.3%和25.7%,并且该催化剂具有良好的循环使用性能.与·OH类似,CuSO_4催化过硫酸钾生成的·SO_4~?自由基也能够有效转化纤维二糖,在纤维二糖转化率为20%时,葡萄糖和葡萄糖酸的选择性分别为36.6%和39.9%.利用这种·OH和·SO_4~?自由基氧化的方法,也能够在较低温度下(333 K)解聚纤维素中的糖苷键.我们发展了H_2O_2浸渍预处理纤维浸渍预处理纤维素的方法,通过部分破坏纤维素糖苷键,提高了纤维素的水解活性.比如:处理后的纤维素在413 K条件下反应12 h,纤维素转化率和葡萄糖选择性分别达到约36.1%和42.5%.XRD结果表明,处理后的纤维素的晶体结构未发生明显的变化.FT-IR表征结果显示处理后的纤维素表面生成了大量的羧酸基团.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.