聚丁二烯/二氧化硅杂化新材料等温结晶动力学及结晶形态的研究

研究了所合成的新型高顺式聚丁二烯键合纳米二氧化硅杂化材料(PB-Si)的顺式-1,4微观结构、特性黏数([η])、微观形态及热稳定性与键合纳米二氧化硅含量的关系等,并采用示差扫描量热仪(DSC)和配有在线冷热台的偏光显微镜(POM)研究了杂化材料PB-Si中SiO_2含量及微观链结构特点对其低温下等温结晶动力学及结晶形态、球晶增长速率的影响.结果表明:当SiO_2含量小于2.5%时,杂化材料PB-Si的特性黏数和顺式-1,4结构含量均基本保持不变,短支链结构的杂化材料(PB-Si-Ni)的顺式-1,4结构含量约为96.6%,高度线性链结构的杂化材料(PB-Si-Nd)的顺式-1,4结构含量约为98.6%,热稳定性均随着SiO_2含量增加而有所提高;在PB顺式-1,4微观结构及SiO_2结合含量基本相同的前提下,与共混物PB/SiO_2相比,杂化材料PB-Si具有更快的结晶速率,且随着杂化材料PB-Si中SiO_2结合量增大,其结晶速率加快,半结晶时间(t1/2)缩短;若杂化材料中顺式-1,4微观结构含量和SiO_2结合量同时增加,杂化材料PB-Si的结晶速率进一步加快;在顺式结构含量及SiO_2含量确定的情况下,聚合物的拓扑结构对其结晶速率也有明显影响,高度线性结构(PB-Si-Nd)比短支链结构(PB-Si-Ni)的杂化材料也具有更快的结晶速率;杂化材料PB-Si在低温等温结晶过程中均呈现三维球晶的生长方式,Avrami指数(n)在2.0~3.0之间,球晶增长速率也随SiO_2结合量增加而加快.     

稀土顺1,4聚丁二烯的分子缠结与结晶

本文用电镜研究了经过分级得到的不同分子量及不同分子量分布的稀土顺1,4 聚丁二烯(Ln-PB)及镍顺1,4 聚丁二烯(Ni-PB)的低温结晶形态、结晶成核及生长机理。发现低分子量 PB以预现成核为主,而高分子量PB以大分子的缠结为中心的散现成核为主,得到两种不同片层缠结形态的PB球晶。其结晶形态及速率主要受高分子量中的大分子缠结影响。     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对PLLA的结晶行为有较大的影响。本文利用差示扫描量热仪(DSC)和偏光显微镜(POM)对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了系统研究。结果表明随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易形保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

稀土顺-1,4-聚丁二烯的搅拌溶液结晶

本工作研究了稀土顺-1,4-聚丁二烯(Ln-PB)的搅拌溶液结晶行为,发现当结晶温度为-15—-79℃、搅拌速度为180转/分时,经过一段时间,就有乳白色的丝状物缠绕在搅拌棒上.在电镜下可以看到,这些丝状物是由平行排列的纤维晶组成的.沉积在搅拌棒上的Ln-PB的量随结晶温度的下降而增加,大约在-65℃左右达到极大值.而后又随结晶温度的下降而减少.结晶温度愈高、沉积在搅拌棒上的Ln-PB的平均分子量愈高,分布愈窄,所以可利用搅拌溶液结晶的方法对Ln-PB进行分级.     

高顺式-1,4-聚丁二烯的结晶形态研究

用稀土催化剂得到的顺-1,4-聚丁二烯具有顺式含量高,支化度小及分子链结构规整性好等特点。在常温下为非晶态,但在低温下易于结晶,因而具有较高的力学性能。本文详细讨论了高顺式稀土顺丁生胶的低温结晶行为。用电子显微镜观察了在低温下球晶结构的形成及其分子结构规整性、结晶条件对结晶形态及结晶速率的影响。     

高氯酸锂对PEO结晶结构和结晶行为的影响

利用配备热台的偏光显微镜(POM)、红外光谱仪(FTIR)和示差扫描量热器(DSC)等实验方法研究了高氯酸锂(LiClO4)与聚氧化乙烯(PEO)之间的络合作用对PEO结晶行为和结晶形态的影响.DSC测试结果表明在LiClO4/PEO二元共混体系中,PEO的熔融温度、结晶温度随着锂盐含量的增加出现先增加后降低的现象;而结晶度则是先不变后降低.FTIR结果表明LiClO4影响聚合物结晶性能的原因是Li+能和PEO中的醚基的络合作用.POM观察结果发现LiClO4/PEO共混体系中存在聚合物的球晶,共混体系中聚合物的球晶生长速率都随着结晶温度的升高而下降,并且球晶生长速率还随着体系中随LiClO4含量的增加而减小.     

不同分子量聚L-乳酸的非等温结晶动力学研究

采用DSC方法研究了不同分子量聚乳酸在不同降温速率下的结晶过程,利用Ozawa方程和Kissinger方程研究了其非等温结晶动力学。结果表明,随着降温速率的增大和分子量增加,结晶峰向低温偏移,且峰形趋于平缓。求得分子量为2.6×104的聚乳酸的Ozawa指数m接近3,以异相成核的三维球晶生长为主,而分子量为14.3×104和19.2×104的聚乳酸的Ozawa指数m接近4,以均相成核的三维球晶生长为主,结晶活化能分别为-165.8kJ/mol、-82.1kJ/mol和-75.4kJ/mol。建立的"铰链"模型解释了不同分子量聚乳酸结晶活化能的显著差异,得到了聚乳酸分子量与结晶活化能的关系。     

异戊橡胶微观序列结构与结晶性能研究

天然橡胶特有的应变诱导结晶能力赋予其优异的力学性能.异戊橡胶作为唯一能够替代天然橡胶的合成橡胶品种,其应变诱导结晶能力受到关注.本文对3种异戊橡胶的微观序列结构进行了分析,并研究了其结晶性能.核磁分析结果表明:3种异戊橡胶的顺-1,4-结构含量差别不大;从1,4-结构单元的键接方式(序列结构)看,SKI-5和YS-IR分子链中顺-1,4-结构单元均以头-尾相接的方式沿分子链排列,不存在头-头键和尾-尾键接方式;SKI-3中约有0.4%~0.5%的1,4-单元采取头-头键接方式,约有0.3%~0.6%的1,4-单元采取尾-尾键接方式;根据定量计算结果,从分子链上1,4-结构单元的序列分布来看,SKI-3的规整性与SKI-5、YS-IR相近或略高.XRD研究结果表明:炭黑填充的天然橡胶硫化胶拉伸至400%以上时发生取向结晶;而炭黑填充的异戊橡胶硫化胶需拉伸至500%以上时才发生取向结晶.基本物理机械性能研究表明:3种异戊橡胶的性能相当,拉伸强度和撕裂强度明显低于天然橡胶;由于结构和组成上的差异,异戊橡胶的结晶能力较天然橡胶差.     

稀土顺-1,4-聚丁二烯的分子量及分子缠结对结晶行为的影响

本工作以线膨胀、体膨胀、DSC、扭辫等方法,在较宽的分子量和结晶温度范围内研究了稀土顺-1,4-聚丁二烯(Ln-PB)的分子量与结晶速率,结晶熔点,玻璃化温度及结晶比表面能之间的关系。进一步考察了分子链缠结对结晶速率的影响,并在结晶成核理论的基础上引入链缠结的影响,导出Ln-PB的结晶动力学方程,得到了与实验符合较好的结果。     

X-射线衍射法研究稀土顺-1,4-聚丁二烯低温结晶动力学

本文用广角X-射线衍射法(WAXD)研究了稀土催化聚合顺-1,4-聚丁二烯(Ln-PB)低温下分子量和温度对结晶过程的影响.随着分子量的改变,结晶速度在M_η=8×10~5左右有一极小值;在M_η=29×10~5左右有一极大值.最大结晶速度发生在T_(c,max)=-60～-70℃之间.最大平衡结晶度值,在M_η大于10~6以上与分子量无关,而最大平衡结晶度值所对应的温度与M_η呈线性关系.随着温度上升,晶胞参数略有增大.Ln-PB主级结晶属于非均相成核,以原纤状和盘状混合生长.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.