Optical band gap and conductivity measurements of polypyrrole-chitosan composite thin films

Electrical conductivity and optical properties of polypyrrole-chitosan（PPy-CHI） conducting polymer composites have been investigated to determine the optical transition characteristics and energy band gap of composite films.The two electrode method and I-V characteristic technique were used to measure the conductivity of the PPy-CHI thin films,and the optical band gap was obtained from their ultraviolet absorption edges.Depending upon experimental parameter,the optical band gap（E_g） was found within 1.30-2.32 eV as estimated from optical absorption data.The band gap of the composite films decreased as the CHI content increased.The room temperature electrical conductivity of PPy-CHI thin films was found in the range of 5.84×10^-7-15.25×10^-7 S·cm^-1 depending on the chitosan content.The thermogravimetry analysis（TGA） showed that the CHI can improve the thermal stability of PPy-CHI composite films.     

Composition and structure of platinum-containing thin composite films prepared from silica sols

Chemical processes that can occur during aging of sols based on water–alcohol solutions of tetraethoxysilane (TEOS) and hexachloroplatinic acid and during formation of films from these sols are analyzed by the results of visible and UV spectroscopy and X-ray powder diffraction. The sizes and compositions of the platinum particles that are formed in xerogels and in thin films on the nanometer and submicron levels are estimated based on X-ray crystallography, energy dispersive spectral analysis, high-resolution scanning and transmission electron microscopy, and grazing incidence small-angle X-ray scattering studies.     

Ordered porous ZnO thin films formed by dip-coating method using PS templates

Monolayer polystyrene spheres (∼400 nm) array templates were assembled orderly on clean glass substrates by dip-coating method from emulsion of polystyrene (PS). Porous ZnO thin films were also prepared by dip-coating method to fill the interstices among the close-packed PS templates with ZnO and annealing to remove the PS templates. Results showed that ZnO sol concentration and dipping time of PS templates in sol had great influences on the morphology of ordered porous ZnO thin films. There was a shrinkage ratio of about 30% from pore to PS. SEM observation showed that the PS array templates had face-centered cubic close-packing. X-ray diffraction (XRD) spectra showed the porous ZnO thin film was wurtzite structure. The optical transmittance decreased with decreasing wavelength of lights, but was kept above 80% beyond the wavelength of 550 nm. Optical band-gap of the porous ZnO thin film annealed at 500°C was 3.22 eV.     

Synthesis and characterization of silica-silver core-shell composite particles with uniform thin silver layers

Silica-silver core-shell composite particles with uniform thin silver layers were successfully synthesized by a facile and one-step ultrasonic electrodeposition method. By electrolysis of the slurry consisting of preformed silica spheres and silver perchlorate without any additives, the homogenous composite particles can be prepared. The average size of single silver crystals in the composite is about 12 nm and the thickness of silver layer is 14±2 nm. Moreover, the continuity of Ag distribution, the surface roughness and the thickness of silver layer are controllable by adjusting the current density (I), the concentration of electrolyte (C) and the reaction time (t). Optical properties of the composite particles with different silver content were also investigated.     

Electronic conductivity of pyrrole and aniline thin films polymerized by plasma

In this article, we present a study of the influence of temperature and humidity on the electric conductivity of polyaniline and polypyrrole thin films doped with iodine and synthesized by plasma (PAn/I and PPy/I, respectively). The polymers presented the characteristic ohmic conduction mechanism via electrons; however, the conductivity was much lower than that presented by the polymers obtained by traditional chemical oxidation. We submitted the polymers to heating–cooling cycles to study the temperature dependence of the conductivity. During the heating stage of the cycles, the electric conductivity of PPy/I showed a strong dependence on the humidity content. However, during the cooling step, the plots of conductivity, as a function of the inverse temperature of PPy/I and PAn/I, showed typical Arrhenius behavior. The activation energy of PPy/I had an average value of 1.1 ± 0.1 eV and was independent of the reaction time, whereas PAn/I presented a more complex behavior with activation energies that depended on the reaction time and the regional crystallinity induced in the heating step of the cycles. All the activation energies were below 2 eV, which places them in the semiconductor regime. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3247–3255, 2000     

Solvent effect on the structure of composite films obtained from chitosan solutions with a precursor of silver nanoparticles

The solvent effect on the structure of nanocomposite films cast from chitosan solutions with AgNO₃ as a precursor of silver nanoparticles was studied for the first time. The size and concentration of silver nanoparticles in the chitosan matrix can be controlled by varying the chitosan-dissolving ability of the solvent with carbonic acid.     

Investigation of thin films formed from liposome suspensions on quartz substrate

The stability of thin wetting films formed from 0.15 M NaCl solutions containing small unilamellar dimyristoylphosphatidylcholine (DMPC) vesicles of different concentrations on quartz surface has been investigated by the microinterferometric method. The intensity of monochromatic light reflected from both film surfaces has been recorded as a function of the time of film thinning. Two temperatures were used in the experiments (20 and 35 degrees C). Films containing 10(-3), 5x10(-3) and 10(-2) mg/ml DMPC were unstable and ruptured, while films with 10(-1) and 1 mg/ml DMPC were stable. Film stability was explained on the basis of hydrophobic interactions. Film thickness dependence on time was calculated. The kinetics of film thinning did not obey Reynolds equation and a linearization was observed in co-ordinates ln(h) as a function of time. This phenomenon was explained by a non-homogeneous thinning process, which might be due to the existence of some areas of different structure of the DMPC adsorption layers.     

Multi-electron transfer in composite phthalocyanine thin films: structure and electrochromic properties

Both sequentially deposited double-layered and codeposited composite thin films were prepared by using two kinds of phthalocyanines. The structure and the electrochromic property of these thin films were compared with those of simple phthalocyanine films. The structures of the films were analyzed by scanning electron microscopy (SEM), X-ray diffrction (XRD) and electron spin resonance (ESR) spectra. From the viewpoint of morphology and crystallinity, codeposited thin films have the same structure as the simple one, having sharp peaks at ca. 2θ=7.0° in the XRD pattern and narrow crystal grains in SEM photographs. ESR measurements have revealed that phthalocyanine molecules disperse very well in the codeposited thin films in a molecular level in comparison with the physical mixture of phthalocyanine powders. This high dispersibility of the molecules in the codeposited thin films can play a role to improve the reversibility in the electrochromism. Thus, the reversibility of the phthalocyanine, which shows irreversible electrochromism in the simple film form, can be improved by the codeposition with another phthalocyanine with reversible electrochromism. In contrast, sequentially deposted double-layered thin film gives completely different results. The electrochromism of the double-layered film depends on the property of the simple phthalocyanine thin film which is in contact with the substrate.     

Theoretical and experimental analyses of the deposited silver thin films

The silver thin films have been prepared using magnetron DC‐sputtering. We discuss in detail the thin films AFM images and their properties in different sputtering times of 2 to 6 minutes. Despite the low thickness of the films, the roughness saturation amounts, W_s, are well separated. The surface data do not follow the normal Family‐Vicsek scaling, and we have the local growth exponent, β(W_s(t)∼t^β). We obtained the global roughness scaling exponent α=0.36 and growth exponent, β=0.50. We also obtain the fractal spectrum of the data, f(α). The results show that the spectrum is right‐hook like. It distinguishes between different film thicknesses even in small sizes of hundreds of nanometers. Furthermore, we measure the surface conductivities and compare them to the thin film roughnesses. We investigate the roughness and fractality of the AFM data, looking for their relations to width and conductivity of the silver thin film samples.     

Synthesis and electrochemical properties of composite films based on poly-3,4-ethylenedioxythiophene with inclusions of silver particles

The electrochemical behavior of PEDOT/Ag composite films obtained by chemical deposition of ultrafine Ag particles into the poly-3,4-ethylenedioxythiophene (PEDOT) matrix was studied. The film morphology was characterized by transmission electron microscopy (TEM). The changes in the mass of the films during the chemical deposition of silver into the polymer structure were evaluated microgravimetrically. The mass of the included metallic silver particles depends on the synthesis time and the initial concentration of silver ions in solution. The cyclic voltammograms (CVs) of PEDOT/Ag films in sodium nitrate solutions and sodium nitrate solutions with additions of chloride ions were studied. The cyclic voltammograms of PEDOT/Ag films in chloride-containing solutions showed the peaks of the oxidation of silver and reduction of the oxidation product, which were absent on the CVs of the starting PEDOT film.     

Thermal conductivity of polyurethane composites containing nanometer- and micrometer-sized silver particles

Polyurethane composites containing spherical and flake-shaped silver fillers of micrometer and nanometer sizes were prepared by reacting suspensions of the silver filler in tetraethylene glycol with Desmodur^? HL BA. Both the thermal conductivity and the stability of the silver composites are increased in comparison with a reference polyurethane sample without filler. Unexpectedly, the largest increases in thermal conductivity and stability are observed for the spherical silver particles of micrometer size but not for the silver nanoparticles, which is reasoned with larger aggregates of silver particles and a higher degree of crystallinity in the sample containing micrometer-sized silver particles.     

Synthesis and structure features of composite silicate and hybrid TEOS-derived thin films doped by inorganic and organic additives

The results of long-term researches of thin films prepared from tetraethoxysilane-derived sols containing inorganic and organic additives are systematized and analyzed. These additives give to films certain physicochemical properties for their application in electronic techniques, optics, power engineering, in biological technologies etc. The influence both inorganic (salts, acids) and organic (polyols, polyionenes, epoxy resin) additives on rheological properties and aggregate stability of sols as well as films surface morphology is minutely considered. The explanations of phenomena during film formation, including spin-coating process, are given. Essential influence of temperature and humidity on films surface morphology is shown. Influence of heat treatment modes on structure and composition of films is analyzed. Recommendations about optimization of thin films sol–gel processing are offered.     

Synthesis of SiO2 thin films by sol-gel method using photoirradiation and molecular structure analysis

The SiO₂ thin films were prepared by a process which combines a sol-gel method and photoirradiation. The HF etch rate and microhardness of a film prepared by this process were better than those of a film furnace-fired at same temperature. The Raman and ²⁹Si solid state NMR spectra of film prepared by this process were similar to those of a film furnace-fired at higher temperature. There are many unstable folded non-linear SiO₂ species in the film prepared at low temperature. On treatment at higher temperature, unstable folded non-linear Si-O-Si rearranges to the stable linear Si-O-Si bond. Photoirradiation enhances this structure change. The process provided denser and harder SiO₂ thin films, even at low temperature, than the conventional furnace-firing method did.     

Preparation and optical properties of silver nanowires and silver-nanowire thin films

Silver nanowires and silver-nanowire thin films have attracted much attention due to their extensive applications in Surface-Enhanced Raman Scattering (SERS) and Surface-Enhanced Fluorescence (SEF). Thin films of silver nanowires within polyelectrolyte layers of poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate) (PSS) were fabricated by the Spin-Assisted Layer-by-Layer (SA-LbL) method. The surface coverage, thickness, and absorbance properties of the silver-nanowire films were controlled by the number of layers deposited. Both transverse and longitudinal surface plasmon (SP) modes of the silver-nanowires were observed in the absorbance spectra, as was evidence for nanowire interaction. Two-dimensional finite difference time-domain (2D FDTD) simulations predict that the maximum field enhancement occurs at the ends and cross-sectional edges of the wires for the longitudinal and transverse modes, respectively. Silver nanowires were synthesized by a facile, high-yield solvothermal approach, which can be easily manipulated to control the aspect ratio of the nanowires. The effects of polyvinylpyrrolidone (PVP) concentration and molecular weight on the growth of the silver nanowires, which are not documented in the original procedure, are discussed. It is shown that the growth mechanism for silver nanowires in the solvothermal synthesis is similar to that reported for the polyol synthesis.     

Polypyrrole thin films formed by admicellar polymerization support the osteogenic differentiation of mesenchymal stem cells

The objective of this study was to evaluate the attachment, proliferation, and differentiation of rat mesenchymal stem cells (MSC) toward the osteoblastic phenotype seeded on polypyrrole (PPy) thin films made by admicellar polymerization. Three different concentrations of pyrrole (Py) monomer (20, 35, and 50 x 10(-3) M) were used with the PPy films deposited on tissue culture polystyrene dishes (TCP). Regular TCP dishes and PPy polymerized on TCP by chemical polymerization without surfactant using 5 x 10(-3) M Py, were used as controls. Rat MSC were seeded on these surfaces and cultured for up to 20 d in osteogenic media. Surface topography was characterized by atomic force microscopy, X-ray photoelectron spectroscopy, and static contact angle. Cell attachment, proliferation, alkaline phosphatase (ALP) activity, and calcium content were measured to evaluate the ability of MSC to adhere and differentiate on PPy-coated TCP. Increased monomer concentrations resulted in PPy films of increased thickness and surface roughness. PPy films generated by different monomer concentrations induced drastically different cellular events. A wide spectrum of cell attachment characteristics (from excellent cell attachment to the complete inability to adhere) were obtained by varying the monomer concentration from 20 m to 50 x 10(-3) M. In particular the 20 x 10(-3) M PPy thin films demonstrated superior induction of MSC osteogenicity, which was comparable to standard TCP dishes, unlike PPy films of similar thickness prepared by chemical polymerization without surfactant. Adhesion of mesenchymal stem cells on tissue culture plates (TCP) coated with polypyrrole thin films made by admicellar polymerization.     

General principles in formation of monolayer colloidal crystals using the moving meniscus method

Factors affecting the formation of two-dimensional periodic structure from the particles of hydrosol disperse phase on the surface of dielectric substrate using the moving meniscus method are analyzed. The analytical model and its numerical realization for calculating the deposition of nanoparticle from bulk hydrosol onto a planar substrate by the Brownian dynamics are represented. Van der Waals, elastic, gravitational, dissipative, and stochastic forces, as well as the action of capillary forces and convective transfer, are taken into account in the model. The influence of various parameters of the disperse system on the degree of imperfection of forming crystalline structure is studied. The dominant factors of structurization during the use of this technique are revealed, and a key role of convective transfer is demonstrated.     

The structure and photoelectrochemical properties of cadmium selenide thin films made by tarnishing reactions

Thin film photoelectrodes of cadmium selenide have been made by using the tarnishing reaction between cadmium metal and selenium vapour. These electrodes have interesting photoelectrochemical properties as seen in photocurrent spectra, impedance measurements etc. They also make quite efficient photoanodes in a photoelectrochemical solar cell. Their structure and growth has been studied by various techniques including spectroellipsometry.     

Study of the structure of thin nanocrystalline films

Structure and phase composition of thin nanocrystalline films of semiconductors and insulators CdS, Cd_xZn_1?xS, SiC_xN_y, and BC_xN_y were studied using registration of weak diffraction intensities with synchrotron radiation. Three methods were developed and applied to obtain diffraction patterns, namely, θ—2-scan (Bragg—Brentano geometry); 2θ-scan (grazing incidence scheme); a scheme with an image plate as detector. The characteristic features of the diffraction patterns, obtained from the aforementioned samples, are discussed. The X-ray diffraction data are compared with the results obtained by HREM, SAED, electron spectroscopy, ellipsometry, IR and Raman spectroscopy. It is stated that: 1) the films are composed of nanocrystals, their size depending on the conditions of film deposition; 2) single crystalline substrate favors formation of oriented crystals, i.e., of the domains comprising uniformly oriented nanocrystals.     

Tribology of thin wetting films between bubble and moving solid surface

This work shows a successful example of coupling of theory and experiment to study the tribology of bubble rubbing on solid surface. Such kind of investigation is reported for the first time in the literature. A theory about wetting film intercalated between bubble and moving solid surface was developed, thus deriving the non-linear evolution differential equation which accounted for the friction slip coefficient at the solid surface. The stationary 3D film thickness profile, which appears to be a solution of the differential equation, for each particular speed of motion of the solid surface was derived by means of special procedure and unique interferometric experimental setup. This allowed us to determine the 3D map of the lift pressure within the wetting film, the friction force per unit area and the friction coefficient of rubbing at different speeds of motion of the solid surface. Thus, we observed interesting tribological details about the rubbing of the bubble on the solid surface like for example: