全氟辛酸钠和溴化烷基三甲铵混合水溶液的界面化学性质

测定了一系列不同比例的C_7F_(15)COONa与阳离子表面活性剂(C_3H_(17)N(CH_3)Br、C_(10)H_(21)N(CH_3)_3Br和C_(12)H_(25)N(CH_3)_3Br)混合水溶液(加NaBr, 恒离子强度μ=0.1 mol kg~(-1))的表面张力及正庚烷/水溶液界面张力。结果表明: 在表面上, 随阳离子表面活性剂碳氢链长增加, 各体系同一比例的饱和总吸附量增大。界面上, 7CFNa～C_8NBr体系的吸附规律与表面相似; 7CFNa～C_(10)NBr体系饱和总吸附量在1:1时最小; 而7CFNa～C_(12)NBr体系, 其饱和吸附量随7CFNa比例减小而减小。混合物的表(界)面活性均比单一表面活性剂高。随着阳离子表面活性剂碳氢链增加, 混合溶液降低表面张力的能力有所下降, 而降低表面张力的效率有所提高, 自表面吸附层结构与表面张力的关系对比作了说明。     

Which surfactants reduce surface tension faster? A scaling argument for diffusion-controlled adsorption

Consider the example of surfactant adsorbing from an infinite solution to a freshly formed planar interface. There is an implicit length scale in this problem, the adsorption depth h, which is the depth depleted to supply the interface with the absorbed surfactant. From a mass balance, h can be shown to be the ratio of the equilibrium surface concentration gamma eq to the bulk concentration C infinity. The characteristic time scale for diffusion to the interface is tau D = h2/D, where D is the diffusivity of the surfactant in solution. The significance of this time scale is demonstrated by numerically integrating the equations governing diffusion-controlled adsorption to a planar interface. The surface tension equilibrates within 1-10 times tau D regardless of bulk concentration, even for surfactants with strong interactions. Dynamic surface tension data obtained by pendant bubble method are rescaled using tau D to scale time. For high enough bulk concentrations, the re-normalized surface tension evolutions nearly superpose, demonstrating that tau D is indeed the relevant time scale for this process. Surface tension evolutions for a variety of surfactants are compared. Those with the smallest values for tau D equilibrate fastest. Since diffusion coefficients vary only weakly for surfactants of similar size, the differences in the equilibration times for various surfactant solutions can be attributed to their differing adsorption depths. These depth are determined by the equilibrium adsorption isotherms, allowing tau D to be calculated a priori from equilibrium surface tension data, and surfactant solutions to be sorted in terms of which will reduce the surface tension more rapidly. Finally, trends predicted by tau D to gauge what surfactant properties are required for rapid surface tension reduction are discussed. These trends are shown to be in agreement with guiding principles that have been suggested from prior structure-property studies.     

Effect of anionic surfactant and short-chain alcohol mixtures on adsorption at quartz/water and water/air interfaces and the wettability of quartz

Measurements of the advancing contact angles for aqueous solutions of sodium dodecyl sulfate (SDDS) or sodium hexadecyl sulfonate (SHS) in mixtures with methanol, ethanol, or propanol on a quartz surface were carried out. On the basis of the obtained results and Young and Gibbs equations the critical surface tension of quartz wetting, the composition of the surface layer at the quartz-water interface, and the activity coefficients of the anionic surfactants and alcohols in this layer as well as the work of adhesion of aqueous solutions of anionic surfactant and alcohol mixtures to the quartz surface were determined. The analysis of the contact angle data showed that the wettability of quartz changed visibly only in the range of alcohol and anionic surfactant concentration at which these surface-active agents were present in the solution in the monomeric form. The analysis also showed that there was a linear dependence between the adhesion and the surface tension of aqueous solutions of anionic surfactant and alcohol mixtures. This dependence can be described by linear equations for which the constants depend on the anionic surfactant and alcohol concentrations. The slope of all linear dependence between adhesion and surface tension was positive. The critical surface tension of quartz wetting determined from this dependence by extrapolating the adhesion tension to the value equal to the surface tension (for contact angle equal zero) depends on the assumption whether the concentration of anionic surfactant or alcohol was constant. Its average value is equal to 29.95mN/m and it is considerably lower than the quartz surface tension. The positive slope of the adhesion-surface tension curves was explained by the possibility of the presence of liquid vapor film beyond the solution drop which settled on the quartz surface and the adsorption of surface-active agents at the quartz/monolayer water film-water interface. This conclusion was confirmed by the work of adhesion of aqueous solutions of anionic surfactants and short-chain alcohol mixtures to the quartz surface determined on the basis of the contact angle data and molar fraction of anionic surfactants and alcohols and their activity coefficient in the surface layer.     

The Hofmeister series effect in adsorption of cationic surfactants--theoretical description and experimental results

Interfacial properties of cationic surfactants show strong dependence on the type of surfactant counterion or on the type of anion of a salt added to the surfactant solution. In the paper, the models of ionic surfactant adsorption that can take into account ionic specific effects are reviewed. Model of ionic surfactant adsorption based on the assumption that the surfactant ions and counterions undergo nonequivalent adsorption within the Stern layer was selected to describe experimental surface tension isotherms of aqueous solutions of a number of cationic surfactants. The experimental isotherms for: n-alkyl trimethylammonium cationic surfactants, namely: C(16)TABr (CTABr or CTAB), C(16)TACl, C(16)TAHSO(4), C(10)TABr and C(12)TABr as well as decyl- and dodecylpyridinium salts with and without various electrolyte anions as Cl(-), Br(-), F(-), I(-), NO(3)(-), ClO(4)(-) and CH(3)COO(-) were described in terms of the model and a good agreement between the theory and experiment was obtained for a wide range of surfactants and added electrolyte concentrations. A very pronounced Hofmeister effect in dependence of surface tension of cationic surfactants on the type of anion was found. Analysing this dependence in terms of the proposed model of ionic surfactant adsorption, strong correlation between "anion surface activity" (the model parameter accounting for ion penetration into the Stern layer), and the ion polarizability was obtained. That suggests that the mechanism related to the dispersive interaction of polarized ion with electric field at interface is responsible for Hofmeister series effects in surface activity of cationic surfactants. The same mechanism was proposed recently to explain the dependence of surface tension increase with electrolyte concentration on anion and cation type.     

The influence of mixed cationic–anionic surfactants on the three-phase contact parameters in silica–solution systems

The formation of thin wetting films on silica surface from aqueous solution of (a) tetradecyltrimetilammonium bromide (C₁₄TAB) and (b) surfactant mixture of the cationic C₁₄TAB with the anionic sodium alkyl- (straight chain C₁₂–, C₁₄– and C₁₆–) sulfonates, was studied using the microscopic thin wetting film method developed by Platikanov. Film lifetimes, three-phase contact (TPC) expansion rates, receding contact angles and surface tension were measured. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetimes, as compared to the pure C₁₄TAB. This behavior was explained by the strong initial adsorption of interfacial complexes from the mixed surfactant system at the air/solution interface, followed by adsorption at the silica interface. The formation of the interfacial complexes at the air/solution interface was proved by means of the surface tension data. It was also shown, that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex and causes synergistic lowering in the surface tension. The film rupture mechanism was explained by the heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface, which remained negatively charged.     

Surface properties of mixtures of surface-active sugar derivatives with ionic surfactants: theoretical and experimental investigations

Surface properties of systems that are mixtures of ionic surfactants and sugar derivatives-anionic surfactant sodium dodecyl sulfate and n-dodecyl-beta-D-maltoside (SDS/DM) and cationic surfactant dodecyltrimethylammonium bromide and n-dodecyl-beta-D-glucoside (DTABr/DG)-were investigated. The experimental results obtained from measurements of surface tension of mixtures with various ratio of ionic to nonionic components were analyzed by two independent theories. First is Motomura theory, derived from the Gibbs-Duhem equation, allowing for indirect evaluation of the composition of mixed monolayers and the Gibbs energies of adsorption, corresponding to mutual interaction between surfactants in mixed adsorbed film. As second theory we used our newly developed theoretical model of adsorption of ionic-nonionic surfactant mixtures. Using this approach, we were able to describe the experimental surface tension isotherms for mixtures of surface-active sugar derivatives and ionic surfactants. We obtained a good agreement with experimental data using the same set of model parameters for a whole range of studied compositions of a given surfactant mixture. The values of surface excess calculated from both theories agreed with each other with a reasonable accuracy. However, the newly developed model of adsorption of ionic-nonionic surfactant mixtures has the advantage of straightforward determination of surface layer composition. By the solution of equations of adsorption, one can obtain directly the values of surface excess of all components (surfactant ions, counterions, and nonionic surfactants molecules), which are present in the investigated system.     

Surface activity and thermodynamic of micellization and adsorption for isooctylphenol ethoxylates, phosphate esters and their mixtures with N-diethoxylated perfluorooctanamide

Three nonionic surfactants; p-isooctylphenol ethoxylates p-[i-OPE10], p-[i-OPE15], and p-[i-OPE20], were phosphorylated to produce three anionic phosphate ester surfactants. In addition, N-diethoxylated perfluorooctanamide (N-DEFOA) was also prepared. The surface and thermodynamic properties of the three types of surfactants and mixtures of the fluorocarbon surfactant (FC) with the hydrocarbon surfactants (HC) have been investigated. Surface tension as a function of concentration of the surfactant in aqueous solution was measured at 30, 40, 50 and 60°C, using the spinning drop technique. From these measurements the critical micelle concentration (CMC), the surface tension at the CMC (γ_CMC), the maximum surface excess concentration (Γ_max), the minimum area per molecule at the aqueous solution/air interface (A_min), and the effectiveness of surface tension reduction (π_CMC), were calculated. The thermodynamic parameters of micellization (ΔG_mic, ΔH_mic, ΔS_mic) and of adsorption (ΔG_ad, ΔH_ad, ΔS_ad) for these surfactants and their mixtures were also calculated. Structural effects on micellization, adsorption and effectiveness of surface tension reduction are discussed in terms of these parameters. The results show that the FC surfactant and its mixtures with HC surfactants enhance the efficiency in surface tension reduction and adsorption in the mixed monolayer at the aqueous solution/air interface, and also, reduce γ_CMC and the tendency towards micellization.     

Dynamic Behavior of Surfactants in Solution

Adsorption of various surfactants at the gas liquid interface is studied with equilibrium and dynamic surface tension measurements. The Wilhelmey plate method and maximum bubble pressure method are used for this study. Dynamic surface tension of solutions of different surfactants, sodium lauryl sulfate (SLS), polyoxyethylene glycol 4‐tert‐octyl phenyl ether (Triton X 100), poly‐oxyethylene(20) cetyl ether (Brij 58), and tetraethylene glycol mono‐n‐dodecyl ether (Brij 30), is measured at different concentrations. Adsorption of different surfactants is compared on the basis of equilibrium and dynamic behavior. Effectiveness and efficiency of different surfactants is found from equilibrium surface tension measurement. A new parameter is defined to quantify the dynamic behavior of adsorption, which gives the concentration of surfactant needed to reduce surface tension to half of its maximum reduction within a defined time available for adsorption. The dynamics of surfactant solution is quantified by using this parameter.     

Effect of charged colloidal particles on adsorption of surfactants at oil-water interface

A change of oil/water interfacial tension in the presence of cationic or anionic surfactants in an organic phase was observed due to the addition of charged fine solids in the aqueous phase. The charged fine solids in the aqueous phase adsorb surfactants diffused from the oil phase, thereby causing an increase in the bulk equilibrium surfactant concentration in the aqueous phase, governed by the Stern-Grahame equation. Consequently, surfactant adsorption at the oil-water interface increases, which was demonstrated from the measured reduction of the oil-water interfacial tension. The increased surfactant partition in the aqueous phase in the presence of the charged particles was confirmed by the measured decrease in the surface tension for the collected aqueous solution after solids removal, as compared with the cases without solids addition.     

The interaction between sodium alkyl sulfate surfactants and the oppositely charged polyelectrolyte, polyDMDAAC, at the air-water interface: the role of alkyl chain length and electrolyte and comparison with theoretical predictions

The effect of alkyl chain length and electrolyte on the adsorption of sodium alkyl sulfate surfactants and the oppositely charged polyelectrolyte, polyDMDAAC, at the air-water interface has been investigated by surface tension and neutron reflectivity. The variations in the patterns of adsorption and surface tension behavior with alkyl chain length and electrolyte are discussed in the context of the competition between the formation of surface active surfactant/polyelectrolyte complexes and polyelectrolyte/surfactant micelle complexes in solution. A theoretical approach based on the law of mass action has been used to predict the surface effects arising from the competition between the formation of polyelectrolyte/surfactant surface and solution complexes and the formation of free surfactant micelles. This relatively straightforward model is shown to reproduce the principal features of the experimental results.     

阴、阳离子表面活性剂混合体系在硅胶/水及硅胶/矿化水界面上的吸附

研究阴、阳离子表面活性剂混合体系(十二烷基氯代吡啶,辛基磺酸钠,辛基三乙基溴化铵/十二烷基苯磺酸钠)在硅胶,纯水和硅胶,矿化水界面上的吸附作用,探讨阴(阳)离子表面活性剂的存在对阳(阴)离子表面活性剂吸附作用的影响．结果表明,阴离子表面活性剂的存在基本不影响阳离子表面活性剂在带负电固体表面的吸附;而阳离子表面活性剂的存在却使本来吸附量就不大的阴离子表面活性剂在带负电的固体表面上不再吸附．在矿化水中阳离子表面活性剂的吸附量比在纯水中明显降低．从硅胶表面吸附机制解释了所得结果．     

The mechanism of hemolysis by surfactants: effect of solution composition

The effect of ionic strength, solute size, and osmolarity of the suspending solution on surfactant-induced erythrocyte hemolysis was studied. Two possible mechanisms of hemolysis were considered: osmotic lysis (affected by solute particle size) and solubilization (not affected by solute particle size). It was found that the ionic strength of the solution has a major effect on the hemolysis process, depending on the surfactant nature and concentration. An increase in the ionic strength lowers the rate of hemolysis induced by DTAB, and enhances SDS-induced hemolysis. Changes in ionic strength have little effect on hemolysis induced by Triton X-100. To explain these effects, it was assumed that the changes in ionic strength differently affect the adsorption of cationic and anionic surfactants to the membrane. The change in the amount of adsorbed surfactant either influences the rate of osmotic hemolysis by changing the membrane permeability or induces a transition from the osmotic mechanism to solubilization. These phenomena were observed for isotonic as well as hypertonic solutions.     

有机反离子对C12-s-C12·2Br水溶液表面活性的影响

溶液中添加的苯磺酸钠(SNzS)和萘磺酸钠(SNphS)与C12-s-C12·2Br产生强烈结合, 增大了Gemini表面活性剂分子的疏水性, 明显促进其在气/液界面的吸附和在溶液中的聚集. 这使得体系降低水表面张力的效率和能力大大提高, 并且在表面活性剂浓度很低时就生成了小聚集体. 因而, 此时表面张力法测得的cmc仅具有表观上的意义, 只反映了表面活性剂在气/液界面达到饱和吸附时的临界浓度. SNphS的疏水性强于SNzS, 更有效地促进了C12-s-C12·2Br的吸附和聚集.     

Gemini表面活性剂烷烃尾链在吸附和聚集过程中的疏水协同效应(英文)

以表面张力法测定了系列Gemini表面活性剂m-6-m以及对应单体表面活性剂CmTABr的临界胶束浓度(cmc)和降低水表面张力20mN·m-1需要的浓度(pC20).比较这些参数表明m-6-m胶束化和在界面吸附的能力均强于CmTABr,这被归结为Gemini表面活性剂烷烃尾链间的疏水协同效应.与不对称Gemini表面活性剂12-6-m比较,对称的Gemini结构更有利于表面活性剂的聚集和吸附.     

Monte Carlo simulations of Lennard-Jones nonionic surfactant adsorption at the liquid/vapor interface

We present Monte Carlo simulations of nonionic surfactant adsorption at the liquid/vapor interface of a monatomic solvent. All molecules in the system, solvent and surfactant, are characterized by the Lennard-Jones (LJ) potential using differing interaction parameters. Surfactant molecules consist of an amphiphilic chain with a solvophilic head and a solvophobic tail. Adjacent atoms along the surfactant chain are connected by finitely extensible harmonic springs. Solvent molecules move via the Metropolis random-walk algorithm, whereas surfactant molecules move according to the continuum configurational bias Monte Carlo (CBMC) method. We generate quantitative thermodynamic adsorption and surface tension isotherms in addition to surfactant radius of gyration, tilt angles, and potentials of mean force. Surface tension simulations compared to those calculated from the simulated adsorbed amounts and the Gibbs adsorption isotherm agree confirming equilibrium in our simulations. We find that the classical Langmuir isotherm is obeyed for our LJ surfactants over the range of head and tail lengths studied. Although simulated surfactant chains in the bulk solution exhibit random orientations, surfactant chains at the interface orient roughly perpendicular and the tails elongate compared to bulk chains even in the submonolayer adsorption regime. At a critical surfactant concentration, designated as the critical aggregation concentration (CAC), we find aggregates in the solution away from the interface. At higher concentrations, simulated surface tensions remain practically constant. Using the simulated potential of mean force in the submonolayer regime and an estimate of the surfactant footprint at the CAC, we predict a priori the Langmuir adsorption constant, KL, and the maximum monolayer adsorption, Gammam. Adsorption is driven not by proclivity of the surfactant for the interface, but by the dislike of the surfactant tails for the solvent, that is by a "solvophobic" effect. Accordingly, we establish that a coarse-grained LJ surfactant system mimics well the expected equilibrium behavior of aqueous nonionic surfactants adsorbing at the air/water interface.     

Effect of gemini surfactant additives on pour point depressant of crude oil

Efficiencies of cationic gemini surfactant additives in improving the pour point depressant of crude oil were investigated. The length of alkyl chain is a major factor affecting the improvement of the pour point depression. The adsorption behavior of these gemini surfactants at air/solution and oil/solution interfaces were investigated by measuring the surface tension and interfacial tension as functions of concentration. It is found that there is a good relation between surface properties especially interfacial tension of the gemini surfactants and their efficiency in depressing the pour point. Also, the surface parameters and free energies of micellization and adsorption confirm the decreasing and improving of pour point depression. Crystallization study in crude oil revealed the relationship between the structure and activity of gemini surfactant additives. It is found that the x-ray diffraction patterns of waxes with additives are remarkably different from those without additives. The mechanism of the depressants action has been suggested according the adsorption of each additive. Adsorption of the additive on the surface of the wax particles inhibits their growth and alters the crystal habits through micelle core. Pretreatment of the crude oil with pour point depressants has received the greatest acceptance due to its simplicity and economy.     

Interaction between polymer and anionic/nonionic surfactants and its mechanism of enhanced oil recovery

Various experimental methods were used to investigate interaction between polymer and anionic/nonionic surfactants and mechanisms of enhanced oil recovery by anionic/nonionic surfactants in the present paper. The complex surfactant molecules are adsorbed in the mixed micelles or aggregates formed by the hydrophobic association of hydrophobic groups of polymers, making the surfactant molecules at oil-water interface reduce and the value of interfacial tension between oil and water increase. A dense spatial network structure is formed by the interaction between the mixed aggregates and hydrophobic groups of the polymer molecular chains, making the hydrodynamic volume of the aggregates and the viscosity of the polymer solution increase. Because of the formation of the mixed adsorption layer at oil and water interface by synergistic effect, ultra-low interfacial tension (～2.0?×?10^?3 mN/m) can be achieved between the novel surfactant system and the oil samples in this paper. Because of hydrophobic interaction, wettability alteration of oil-wet surface was induced by the adsorption of the surfactant system on the solid surface. Moreover, the studied surfactant system had a certain degree of spontaneous emulsification ability (D50?=?25.04?µm) and was well emulsified with crude oil after the mechanical oscillation (D50?=?4.27?µm).     

Interplay between the surface adsorption and solution-phase behavior in dialkyl chain cationic-nonionic surfactant mixtures

Neutron reflectivity, NR, and surface tension have been used to study the adsorption at the air-solution interface of mixtures of the dialkyl chain cationic surfactant dihexadecyl dimethyl ammonium bromide (DHDAB) and the nonionic surfactants monododecyl triethylene glycol (C12E3), monododecyl hexaethylene glycol (C12E6), and monododecyl dodecaethylene glycol (C12E12). The adsorption behavior of the surfactant mixtures with solution composition shows a marked departure from ideal mixing that is not consistent with current theories of nonideal mixing. For all three binary surfactant mixtures there is a critical composition below which the surface is totally dominated by the cationic surfactant. The onset of nonionic surfactant adsorption (expressed as a mole fraction of the nonionic surfactant) increases in composition as the ethylene oxide chain length of the nonionic cosurfactant increases from E3 to E12. Furthermore, the variation in the adsorption is strongly correlated with the variation in the phase behavior of the solution that is in equilibrium with the surface. The adsorbed amounts of DHDAB and the nonionic cosurfactants have been used to estimate the monomer concentration that is in equilibrium with the surface and are shown to be in reasonable qualitative agreement with the variation in the mixed critical aggregation concentration (cac).     

Adsorption Properties of Hydrocarbon and Fluorocarbon Surfactants Ternary Mixture at the Water-Air Interface

Measurements were made of the surface tension of the aqueous solutions of p-(1,1,3,3-tetramethylbutyl) phenoxypoly(ethylene glycols) having 10 oxyethylene groups in the molecule (Triton X-100, TX100) and cetyltrimethylammonium bromide (CTAB) with Zonyl FSN-100 (FC6EO14, FC1) as well as with Zonyl FSO-100 (FC5EO10, FC2) ternary mixtures. The obtained results were compared to those provided by the Fainerman and Miller equation and to the values of the solution surface tension calculated, based on the contribution of a particular surfactant in the mixture to the reduction of water surface tension. The changes of the aqueous solution ternary surfactants mixture surface tension at the constant concentration of TX100 and CTAB mixture at which the water surface tension was reduced to 60 and 50 mN/m as a function of fluorocarbon surfactant concentration, were considered with regard to the composition of the mixed monolayer at the water-air interface. Next, this composition was applied for the calculation of the concentration of the particular surfactants in the monolayer using the Frumkin equation. On the other hand, the Gibbs surface excess concentration was determined only for the fluorocarbon surfactants. The tendency of the particular surfactants to adsorb at the water-air interface was discussed, based on the Gibbs standard free energy of adsorption which was determined using different methods. This energy was also deduced, based on the surfactant tail surface tension and tail-water interface tension.