Polarization modulation Fourier transform infrared spectroscopy

Polarization modulation Fourier transform infrared spectroscopy can be measured by either double modulation FTIR or interferometric modulation FTIR techniques. The principles of both techniques are presented with examples of representative measurements. The relative advantages and disadvantages of each method are compared.     

Fourier transform raman spectroscopy using a bench-top fourier transform infrared spectrometer

The use of a bench top FTIR spectrometer for near infrared Fourier transform Raman spectroscopy is demonstrated. The use of near infrared excitation results in fluorescence free Raman spectra allowing previously difficult samples to be measured.     

Seafood freshness determination through vapour phase Fourier transform infrared spectroscopy

A new vapour-phase manifold has been developed to determine trimethylamine (TMA) in fish and cephalopod samples by Fourier transform infrared (FT-IR) spectroscopy. Samples were treated off-line for 1 h with trichloroacetic acid (TCA), filtered and washed. The obtained extracts were aspirated and alkalinized with NaOH 2.0 M, in an on-line system. TMA was separated from the solution in a gas phase separator and then transported by means of a nitrogen carrier into a home made 10 cm pathlength IR gas cell, where the corresponding FT-IR spectra were acquired by accumulating 30 scans per spectrum with 2 cm⁻¹ nominal resolution. The method was applied to the determination of TMA in natural samples providing concentration values statistically comparables with those obtained by a head space gas chromatography (HS-GC) reference procedure. The sample throughput by FT-IR is increased by a factor of 6 as compared with HS-GC.     

Comparison and joint use of near infrared spectroscopy and Fourier transform mid infrared spectroscopy for the determination of wine parameters

A study of the statistic characteristics of the multidetermination of several enological parameters - namely, alcoholic degree, volumic mass, total acidity, glycerol, total polyphenol index, lactic acid and total sulphur dioxide - depending on the spectroscopic zone employed, was carried out. The two techniques used were near infrared spectroscopy (NIRS) and Fourier transform mid infrared spectroscopy (FT-MIRS). The combination of these two regions (sum of their spectra) was also studied. NIRS yielded better results, but the use of both zones improved the determination of glycerol and total sulphur dioxide. The training and validation sets used for developing general equations were built with samples from different apellation d’origine, different wine types, etc. Partial least squares regression was used for multivariate calibration, using systematic cross validation in the calibration stage and external validation in the testing stage. Sample preparation was not required.     

Rapid discrimination of Eurycoma longifolia extracts by Fourier transform infrared spectroscopy and two dimensional correlation infrared spectroscopy

Eurycoma longifolia is a herbal medicinal plant of South-East Asian origin, popularly recognized as ‘Tongkat Ali’. The root extracts have been used in indigenous traditional medicines for its unique antimalarial, anti-pyretic, antiulcer, cytotoxic and aphrodisiac properties. It is an important task that fast and effective analysis methods monitor the inherent qualities of traditional herbal medicines and its corresponding extracts products as a complicated mixture system. Owing to the unique fingerprint character and extensive applicability to test sample, infrared spectral method have been used in many research fields. In this paper, we use FT-IR, second derivative infrared spectroscopy and two-dimensional correlation infrared spectroscopy (2D-IR) step by step to analyze E. longifolia and its different extracts (extracted by hexane, ethyl acetate, dichloromethane and methanol in turn). The findings indicated that FT-IR and 2D-IR can provide many holistic variation rules of chemical constituents. The structural information of the samples indicated that E. longifolia and its extracts contain a large amount of quassinoids, since some characteristic absorption peaks of quassinoids, such as ∼1700 cm⁻¹, ∼1670 cm⁻¹, ∼1600 cm⁻¹,∼1500 cm⁻¹, and ∼1270 cm⁻¹ can be detected. This method, having its high resolution and excellent macroscopic fingerprint features, can not only supply lots of structural information of main components in the complicated system, but also can differentiate the tiny differences between the similar systems according to the macro-fringerprint characters. This method is highly rapid, effective, accurate and well repetitive for pharmaceutical research.     

Polymeric hydrogels modified with ornithine and lysine: Sorption and release of metal cations and amino acids

A novel, convenient synthesis, using copper ions, is described for the multigram‐scale preparation of acryloyl and methacryloyl ornithine and lysine without the need to use protecting groups and chromatographic purifications. Three methods of removing the copper ions from the amino acid derivatives were examined. The obtained acryloyl and methacryloyl ornithine and lysine were copolymerized with N‐isopropylacrylamide and N,N′‐methylenebisacrylamide as crosslinking agents, resulting in a series of hydrogels with varying incorporated amino acid content. The relative content of a given amino acid was estimated from the ¹H NMR data and compared with its molar fraction used in the polymerization process. We investigated the influence of the amount of amino acid groups incorporated into the polymer network on the swelling behavior of the gels in the presence of metal ions of different ability to form complexes (Cu²⁺, Co²⁺, and Ca²⁺) with α‐amino acid groups and the sorption of copper ions. Next, the presence of α‐amino acid groups attached to the polymer network was used to bond the compounds which can cocomplex metal ions. Phenylalanine was selected for examination of its cocomplexation of Cu²⁺ with the polymer‐network amino acids and its consecutive release from the gel after appropriate change of pH. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Comparative analysis of smokeless gunpowders by Fourier transform infrared and Raman spectroscopy

Fourier Transform Infrared (FTIR) and Raman spectroscopic techniques were used to perform a comparative study of the spectral profiles of single-base, double-base and triple-base smokeless gunpowders. Preliminary results based on visual comparison of the spectra point out that spectra obtained by both vibrational techniques were useful for a rapid identification of gunpowders containing dinitrotoluene as one of the major components and triple-base gunpowders. Additionally, the Raman spectra of gunpowders with diphenylamine in its primary composition showed a characteristic band, assigned to 2-nitro-diphenylamine, allowing the identification of this type of gunpowders.     

Albumin and fibrinogen adsorption onto phosphatidylcholine monolayers investigated by Fourier transform infrared spectroscopy

Dipalmitoylphosphatidylcholine (DPPC) monolayers were deposited onto a germanium attenuated total reflectance (ATR) crystal using the Langmuir–Blodgett technique. The DPPC-coated crystal was then exposed to human serum albumin or human fibrinogen solutions while measuring the protein adsorption by recording FTIR spectra. The effect of the zwitterionic nature of the DPPC polar headgroup towards protein adsorption has been ascertained by exposing either the phospholipid headgroup or the acyl chains to the protein solution; this was possible by the use of a silanized or a bare germanium crystal. Calibration curves have been made to measure the protein surface concentrations. After 3 h, the albumin surface concentration on DPPC monolayers was about three times higher when the proteins were exposed to the lipid acyl chains instead of the polar headgroups (e.g. 3 vs. 1 μg cm⁻²). As for fibrinogen (FGN) adsorption, when the lipid polar headgroups were exposed to the protein solution, the FGN adsorption was low reaching a maximum value of 0.5 μg cm⁻². When interacting with the lipid acyl chains, the FGN adsorption reached a plateau at a value of 2.1 μg cm⁻² after 3 h. Clearly, both albumin and FGN showed a low tendency to adsorb on surfaces where the lipid polar headgroups are exposed toward the protein solution.     

Determination of total sterols in brown algae by Fourier transform infrared spectroscopy

A procedure is proposed for the determination of the total amount of sterols in brown algae Bifurcaria bifurcata, Cladostephus hirsitus, Dictyota dichotoma and Cystoseira sedoides, globally determined as fucosterol, which is the major sterol contained in these algae. The method involves the use of cholesterol as reference standard and a correction factor of 1.259 ± 0.003, which represents the ratio between the slopes of calibration lines obtained from fucosterol and cholesterol. The method provides precise and accurate results for the IR analysis of real samples.     

Low-frequency surface-enhanced Raman scattering spectroscopy at metal electrode surfaces

Low-frequency surface-enhanced Raman scattering (SERS) spectroscopy is a versatile tool for studying surface phenomena under electrochemical conditions. This spectroscopy enables us to obtain rich information on extramolecular vibrations between substrate and adsorbates, which are sensitive to atomistic surface features of the substrate. Owing to recent advancements in optical filter technology, low-frequency SERS signals are now becoming easily detectable using conventional Raman systems equipped with holographic notch filters. In addition, SERS background signals, which have been simply ignored, can provide electronic information on the metal substrate. This allows us to observe both sides of electrode–electrolyte interfaces in situ and simultaneously, which is never expected in far-infrared or terahertz absorption spectroscopy. This advanced SERS spectroscopy can help our understanding of electrochemical and electrocatalytic reactions at the molecular scale.     

Double modulation Fourier transform infrared photoluminescence of InSb

The near-gap photoluminescence of the narrow gap semiconductor, InSb, has been measured near 5.3m at low temperatures excited with argon laser light using a modified commercial Fourier transform infrared spectrophotometer. Both conventional and double modulation techniques were used for removing the effect of the thermal background radiation. Three peaks were observed in the spectrum of which the first and second were assigned to band-to-band emission, band-to-impurity emission, and the third, hitherto unreported, peak to an acceptor-bound exciton transition.     

Fourier transform infrared photoacoustic spectroscopy of dental calculus

The mid and far FTIR spectra of supragingival and subgingival calculus were measured, respectively. From the subtraction spectra of the two types of calculus, the protein components of calculus have been obtained. The results of photoacoustic spectroscopy indicated the presence of protein layer on the surface of early calculus.     

Instrumental barriers in biological Fourier transform infrared spectroscopy

Biological applications of infrared spectroscopy have pressed for ever greater instrumental capabilities in terms of spectral sensitivity and quantitative exactness. Improved instrumentation has provided measurement of many vibrational modes in biological samples that previously were lost in noise. With highly optimized sampling conditions, useful measurements have been made with a peak-to-peak noise level less than 5 microabsorbance (5×10^–6 absorbance), at 0.5 cm^–1 resolution. However, optical and instrumental instabilities often result in sine waves that are not totally removed by the ratio of sample to reference. These often limit effective spectral sensitivity to 50 or 100 microabsorbance, peak-to-peak, and constitute a non-random noise. Non-atmospheric absorptions, especially one at 1959 cm^–1 with 0.8 cm^–1 band width (FWHM) are reported. The latter is due to a trace impurity in the KBr beam splitter substrate and compensator plate. Improvements in instrumentation and sampling conditions are expected to yield measurements of absorption bands as small as 50 microabsorbance with excellent signal/noise.     

Dynamic Fourier transform infrared spectroscopy in polymer research

The rapid-scanning capability of FTIR instrumentation has revitalized the field of vibrational spectroscopy in polymer research and will be discussed with reference to the study of polyurethane kinetics, the temperature dependence of hydrogen bonding in polyamide 6 and strain-induced crystallization in a polydimethylsiloxane elastomer.     

Adsorption of carbon monoxide and oxygen on transition metal surfaces: A comparative study of the results from electron spectroscopy and theoretical calculations

Results of investigations on the adsorption of CO andO ₂ on transition metal surfaces by employinguv and x-ray photoelectron spectroscopy and electron energy loss spectroscopy (eels) are presented. Results of molecular orbital calculations on adsorbed CO and O₂ are also discussed. Some of the interesting aspects discussed are, satellites in the O(ls) region due to adsorbed CO, vibrationaleels of adsorbed O₂ and dissociation energy profiles of adsorbed O₂ on clean surfaces as well as surfaces covered with potassium or presorbed atomic oxygen. Contribution No 245 from the Solid State and Structural Chemistry Unit.     

红外光谱法测定壳聚糖含量(英文)

采用吡喃环上的次甲基的吸收峰(1 389和2 865cm-1)面积比作为定量参照,建立了一种检测壳聚糖含量的傅立叶变换红外光谱(FT-IR)分析方法,并验证了其适用性.结果表明,所建立的FT-IR分析方法可用于定量测定药物剂型中的壳聚糖含量.     

XPS studies of amino acids adsorbed on titanium dioxide surfaces

Summary Adsorption of amino acids from aqueous solutions on TiO₂ surfaces as a function of pH is monitored quantitatively by X-ray photoelectron spectroscopy (XPS). Because of the amphoteric character of the TiO₂ and the zwitterionic behaviour of the amino acids the pH of adsorption indicates what chemical groups are involved in the adsorption reaction. The results confirm the ligand exchange model: in acidic milieu the carboxylic group replaces a basic surface hydroxyl group on a Ti site and binds to this Ti. For homocysteine the resulting position of the adsorbed molecule can also be concluded by comparing peak intensities.