Micellar chromatographic determination of partition coefficients and associated thermodynamic data for pharmaceutical compounds

Micelle/water partition coefficients were obtained for procaine hydrochloride using micellar liquid chromatography (MLC) to illustrate the potential application of this technique to compounds of pharmaceutical interest. Experiments were conducted over a temperature range which led to calculation of a Gibbs free energy, enthalpy and entropy of transfer for procaine hydrochloride. Successful application of this technique was confirmed using a second compound over a range of temperatures, namely caffeine. Overall, this work confirms that MLC can be used to determine precise and accurate partition coefficients that possibly more closely mimic biological membranes than traditional in vitro systems, namely octanol/water.     

固相萃取-反相高效液相色谱法测定水中的邻苯二甲酸酯

建立了固相萃取-反相高效液相色谱法检测水中3种邻苯二甲酸酯类物质邻苯二甲酸二甲酯、邻苯二甲酸二(2-乙基己基)酯、邻苯二甲酸二正辛酯的方法. 考察了固相萃取柱、洗脱溶剂、洗脱体积、上样速度以及洗脱速度对萃取效率的影响. 通过综合分析, 选定SupelcleanLC-18 SPE Tube固相萃取柱, 甲醇为洗脱剂, 洗脱体积2 mL, 上样速度为4 mL/min, 洗脱速度为1 mL/min. 在此萃取条件下, 萃取回收率在83.4%～121.2%之间. 邻苯二甲酸二甲酯、邻苯二甲酸二(2-乙基己基)酯、邻苯二甲酸二正辛酯质量浓度在2～100 mg/L之间均为线性. 经萃取后, 方法的最低检出限分别为邻苯二甲酸二甲酯0.06 μg/L, 邻苯二甲酸二(2-乙基己基)酯0.16 μg/L, 邻苯二甲酸二正辛酯0.08 μg/L. 方法的精密度在10%～15%之间. 应用该方法测定自来水中酞酸酯类化合物的含量, 加标回收率为83.6%～110.2%.     

Determination of octanol/water partition coefficients by flow injection analysis

Determination of octanol/water partition coefficients by batch-extraction methods is currently the only acceptable procedure for application to structure/activity relationships. Work on the development of flow-injection systems to determine these partition coefficients is reported. It is shown that it is not necessary to know the concentration of the analytic in either phase; the partition coefficient should be equal to the differences in the octanol and water peak widths divided. by the system residence time. For a limited number of compounds, this is shown to be valid. Several systems were developed, including a flow-through dialyzer which was 5 times more efficient than the best commercial unit.     

Determination of liposome/water partition coefficients of organic acids and bases by solid-phase microextraction

The extraction of two methylated anilines and three chlorinated phenols by solid-phase microextraction (SPME) fibers coated with polyacrylate was investigated as a function of pH. Only the neutral species of the acids and bases partitioned into the polymer. Extraction kinetics were accelerated for the hydrophobic phenols at pH values around their acidity constant. This is presumably due to a reconstitution of the neutral species in the unstirred aqueous layer adjacent to the polymer surface by the charged species through the fast acid-base equilibrium. Although the charged species is not taken up into the polymer, liposome/water distribution ratios could be measured up to a pH value, where 99% of the compounds were present as charged species. The partition coefficients of the neutral and charged species were extrapolated from the pH profiles of the liposome/water distribution ratios. The resulting values were slightly lower than those measured with equilibrium dialysis. The discrepancies are discussed with respect to differences in the experimental conditions and the possibility of matrix effects during SPME measurements.     

Determination of octanol-water partition coefficients for carbonate esters and other small organic molecules by microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) was assessed as a tool for determination of octanol-water partition coefficients using 34 solutes encompassing 8 carbonate esters. It was confirmed that microemulsions containing 1.44-2.88% w/w SDS, 6.49% w/w 1-butanol, and 0.82% w/w n-heptane constitute a good model of octanol-water partitioning in the pH range of 1.4-7.4. Use of the migration index concept led to improved repeatability of the MEEKC method compared to the use of retention factors. Using a dynamical coating, a high electroosmotic flow at pH 1.4 and 4.75 was achieved expanding the practical pH working range of the MEEKC system. The correlation obtained between the migration index and log P was unaffected by pH indicating that the properties of the microemulsion droplets and, thus, partitioning are independent of pH. No evidence for congeneric behavior was found for the sample set comprising solutes with different hydrogen bonding properties suggesting that simple reference compounds can be used as calibrators. Lipophilicity estimates for the series of carbonate esters were obtained. The increase in lipophilicity with chain length was smaller than expected from the Hansch substituent constant, pi.     

Application of single-drop microextraction to the determination of dialkyl phthalate esters in food simulants

A fast and simple method, using static single-drop microextraction (SDME), has been developed to facilitate the identification and quantification of seven dialkyl phthalate esters in the three aqueous food simulants. The simulants were: A, distilled water; B, 3% (w/v) acetic acid/water; and C, 15% (v/v) ethanol/water. The extraction is performed by simply suspending a drop of organic solvent in the aqueous sample using a conventional gas chromatography (GC) microsyringe. Following extraction, the organic phase is withdrawn into the syringe and analyzed by gas chromatography and flame ionization detection (FID). The optimized method yields a linear calibration curve over three orders of magnitude for all the simulants, and method detection limits (MDLs) allowing detection of all the studied compounds at concentrations below migration limits established by the European Union. The accuracy of the SDME method was tested and compared to that of solid-phase microextraction (SPME) by recovery experiments using spiked samples, with results ranging from 85 to 115% in most cases.     

Development of a time-resolved fluoroimmunoassay for phthalate esters in water

Summary An antigenic derivative of dimethylphthalate has been synthesized and used to raise an antibody that selectively recognizes o-phthalate esters. With this antibody we have standardized a direct time-resolved fluoroimmunoassay for these esters in water. Its sensitivity is 0.5 pmol/ml.     

Computational prediction of ionic liquid 1-octanol/water partition coefficients

Wet 1-octanol/water partition coefficients (log?K(ow)) predicted for imidazolium-based ionic liquids using adaptive bias force-molecular dynamics (ABF-MD) simulations lie in excellent agreement with experimental values. These encouraging results suggest prospects for this computational tool in the a priori prediction of log?K(ow) values of ionic liquids broadly with possible screening implications as well (e.g., prediction of CO(2)-philic ionic liquids).     

GC-MS/MS法测定沉积物和生物样品中邻苯二甲酸酯

采用固相萃取(SPE)和QuEChERS技术结合气相色谱-串联质谱(GC-MS/MS)技术,建立了养殖海域沉积物和生物样品中16种邻苯二甲酸酯(PAEs)定量分析方法.沉积物样品以二氯甲烷为提取溶剂,经PSA-Silica固相萃取柱净化,生物样品以乙腈为提取溶剂,经150.0 mg N-丙基乙二胺(PSA)、150.0...     

Measurement of bilirubin partition coefficients in bile salt micelle/aqueous buffer solutions by micellar electrokinetic chromatography

The partition coefficients for the distribution of bilirubin between aqueous phosphateborate buffer and cholic, taurocholic, taurodeoxycholic, and taurochenodeoxycholic micelles have been measured by micellar electrokinetic chromatography at pH 8.5. Determination of the partition coefficients required that the critical micelle concentration and partial specific volumes be determined for each bile salt. Critical micelle concentrations were slightly higher for the trihydroxy bile salts. Partial specific volumes of the bile salt micelles differed very little from each other, and for each bile salt they were constant over the concentration range studied, which was typically from slightly above the critical micelle concentration to 35 mM. Capacity factors were corrected for the effects of applied voltage by extrapolation of the capacity factor to zero applied volts. The free solution mobility of bilirubin, determined in the absence of bile salt, was also corrected for the effects of applied voltage. Plots of extrapolated capacity factor versus phase ratio yield the partition coefficient as the slope of a linear fit to the data. Partition coefficients for bilirubin were significantly higher for dihydroxy bile salts than for trihydroxy bile salts.     

Determination of partition coefficients and residual solvent for polymer drying applications

Summary Gas-solid partition coefficients (K) for n-hexane in high density polyethylene (HDPE) have been measured at conditions applicable to large-scale drying utilizing a novel headspace method. The method features considerable versability and simplicity due to the control of experimental conditions designed to favor full extraction of the analyte into the headspace. By combining this full extraction technique with a traditional static headspace experimental scheme, a method which measuresK and residual concentration is achieved. The results show that partition coefficients differ significantly between HDPE in its virgin powder and pellet forms, as well as among various HDPE grades. The differences are shown to be attributable to differences in % crystallinity of the specific polymer. Data collected over a wide range of hexane concentrations reveals saturation levels (solubilities) which correspond to crossover from evaporative to diffusion-controlled drying.     

Determination of gas-liquid partition coefficients by gas chromatography

This review covers theoretical principles and experimental procedures for the determination of gas-liquid partition coefficients, KL, by gas chromatography. In order to precisely define the relationship between KL, retention time and experimental parameters, the retention theory, both for ideal and for imperfect gas phase, is expounded. The most important sources of systematic error, as peak asymmetry, mixed retention mechanisms, column hold-up time and stationary phase mass determination, are discussed. Although the review is focussed on packed columns, comparison to capillary columns is discussed in those aspects in which these last show advantages.     

Determination of liquid-liquid partition coefficients by separation methods

By essence, all kinds of chromatographic methods use the partitioning of solutes between a stationary and a mobile phase to separate them. Not surprisingly, separation methods are useful to determine accurately the liquid-liquid distribution constants, commonly called partition coefficient. After briefly recalling the thermodynamics of the partitioning of solutes between two liquid phases, the review lists the different methods of measurement in which chromatography is involved. The shake-flask method is described. The ease of the HPLC method is pointed out with its drawback: the correlation is very sensitive to congeneric effect. Microemulsion electrokinetic capillary electrophoresis has become a fast and reliable method commonly used in industry. Counter-current chromatography (CCC) is a liquid chromatography method that uses a liquid stationary phase. Since the CCC solute retention volumes are only depending on their partition coefficients, it is the method of choice for partition coefficient determination with any liquid system. It is shown that Ko/w, the octanol-water partition coefficients, are obtained by CCC within the -1 < log Ko/w < 4 range, without any correlation or standardization using octanol as the stationary phase. Examples of applications of the knowledge of liquid-liquid partition coefficient in the vast world of solvent extraction and hydrophobicity estimation are presented.     

Air/water partition coefficients for normal alkanes (n-pentane to n-nonane)

Consistent values of the air/water partition coefficient for n-pentane, n-hexane, n-heptane, n-octane and n-nonane have been measured in the temperature range 15–35°C. All of the results may be summarised by an equation derived on the basis of thermodynamic principles. The constants of this equation have been determined by least-squares regression. The solubilities of hydrocarbons in water as well as thermodynamic quantities relating to the solvation process can be predicted using the equation.     

Determination of polydimethylsiloxane-air partition coefficients using headspace sorptive extraction

Polydimethylsiloxane-air partition coefficients (K(PDMS-A)) were determined using direct headspace analysis and headspace sorptive extraction (HSSE) with polydimethylsiloxane-coated (PDMS) stir bars. The partition coefficients were investigated for three compounds, p-dichlorobenzene (PDCB), naphthalene and camphor, all of which sublimate at room temperature and find use as moth repellents. In order to determine the K(PDMS-A) values of these compounds, the air concentration and the concentration present on PDMS, both at equilibrium, were measured. The results indicate that PDMS-air partition coefficients are proportional to octanol-air partition coefficients. Thus, the latter could be used to estimate the extraction efficiency of PDMS for these compounds in air. Alternatively, octanol-air partition coefficients for organic compounds could be estimated from the PDMS-air partition coefficient values. As expected, the PDMS-air (or octanol-air) partition coefficient increased with decreasing temperature. Importantly, the partition coefficients determined at saturated vapor pressures were lower than the values determined at lower analyte concentrations, with the differences being greater for compounds with larger partition coefficients. Consequently, caution should be exercised when applying K(PDMS-A) values determined at high analyte concentrations to measurements at lower concentrations, especially when the partition coefficients are large.     

Determination of phthalate esters in water samples by solid-phase microextraction and gas chromatography with mass spectrometric detection

Solid-phase microextraction (SPME) with an 85 microm polyacrylate fiber, coupled to gas chromatography-mass spectrometry was used to determine six phthalate esters and bis(2-ethylhexyl) adipate in water samples. The variables affecting the SPME absorption process were optimized and the method developed was applied to analyze both tap and commercial mineral water samples as well as water from the Ebro river and fishing and industrial ports. For real samples, the linear range in full scan acquisition mode was between 0.02 and 10 microg l(-1) for most compounds, and the limits of detection of the method were between 0.006 and 0.17 microg l(-1). Commercial water samples contained in recipients which were made from different materials were analyzed, and the influence of the material of the recipients on the concentration of phthalates was evaluated.     

保留时间两点校正反相高效液相色谱法测定持久性有机污染物的正辛醇-水分配系数

采用改进的反相高效液相色谱法(RP-HPLC)测定了持久性有机污染物(POPs)包括多环芳烃(PAHs)、多氯二苯并二恶英(PCDDs)、多氯二苯并呋喃(PCDFs)和十溴二苯乙烷(DBDPE)等的正辛醇-水分配系数(logKow)。采用保留时间双点校正法(DP-RTC)校正因色谱柱老化等引起的保留时间漂移。以37种有可靠logKow实验值的苯系物、PAHs、PCDD/Fs类似物为模型化合物,建立了logKow和外推至纯水相的保留因子logkw的定量结构-色谱保留关系(QSRR)模型,回归方程为logKow=(1.18±0.02)logkw+(0.36±0.11),其相关系数(R2)为0.985,交叉验证相关系数(R2cv)为0.983,标准偏差(SD)为0.16。进而,用4个已有可靠logKow实验值的验证化合物(联苯、芴、PCDD 1和PCDF 114)对模型进行了外部验证,表明RP-HPLC测得的logKow值与摇瓶法/慢搅法结果有很好的一致性,尤其是对疏水性强的化合物。采用该模型测定了29种特别受关注的POPs的logKow值,这些化合物的logKow实验值均未见报道。所建立的DP-RTC-HPLC是测定强疏水性POPs的logKow值的一种值得推荐的方法。