有序介孔碳涂层纤维固相微萃取用于环境水样中苯系物的测定

本文采用直接粘合法制备了有序介孔碳涂层萃取纤维,并将其应用于水中苯、甲苯、乙苯、邻二甲苯4种苯系物的固相微萃取。结果表明,所合成的介孔碳粉末孔径分布集中,比表面积和孔容分别为701.4m~2/g和0.353cm~3/g,制备得到的涂层完整、连续,与基体结合紧密。采用顶空-固相微萃取与气相色谱-质谱联用技术对水样中的苯系物进行分析测定,结果表明:该萃取纤维具有良好的热稳定性和溶剂稳定性;在最佳萃取及检测条件下,方法线性范围为1~1 000μg/L,相关系数良好;检出限在0.086~0.088μg/L之间;同一涂层的相对标准偏差(RSD,n=5)为2.0%~5.5%;萃取效率远远高于商用聚二甲基硅氧烷涂层(PDMS,100μm)和商用聚丙烯酸酯涂层(PA,85μm)。将此方法应用于两种实际水样的检测,没有检测到4种苯系物,在两个不同浓度的加标条件下,样品回收率均在81.0%~112.8%之间,满足实际分析要求。     

用C16-MCM-41介孔涂层新型固相微萃取-高效液相色谱分析环境水样中的痕量蒽

首次建立了1种用C16-MCM-41介孔复合材料作纤维涂层的固相微萃取(SPME)与高效液相色谱(HPLC)联用,测定环境水样中痕量葸的方法;对SPME的实验条件,如萃取和解吸时间、萃取温度、搅拌速度以及离子强度等进行了优化;方法的线性范围为0．018—71．2μg.L^-^1,检出限为5．9ng.L^-^1(S／N=3),相对标准偏差为0．033％(RSD,n=7);该法体现了SPME在样品前处理过程中的快速、灵敏、简单和无溶剂的特点。     

有序介孔碳-固相微萃取涂层的制备及应用

采用溶剂诱导挥发自组装和提拉法制备了以纯有序介孔碳为涂层的新型固相微萃取装置。利用N2吸附-脱附,扫描电镜对涂层材料的性质进行了表征。优化了萃取分析条件,采用顶空-固相微萃取的方法测定自来水中的甲苯和苯乙烯。与商品化涂层相比较,自制涂层具有萃取容量大、使用寿命长的优点。甲苯、苯乙烯含量在0.5~500μg/L内具有良好的线性,检出限为80 ng/L,RSD均小于12%。方法用于测定自来水中的甲苯与苯乙烯,加标回收率为90.2%和93.5%。     

介孔涂层固相微萃取-高效液相色谱法测定水样中邻苯二羧酸酯化合物

以苯基官能化MCM-41介孔复合体作为固相微萃取(SPME)的吸附涂层, 与高效液相色谱(HPLC)联用测定了不同水样中邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)和邻苯二甲酸二辛酯(DOP)的含量, 对SPME的吸附和解吸时间、温度、搅拌速度进行了优化, 线性范围分别为1.19×10-4～119 μg/L、 1.12×10-4～112 μg/L、 1.05×10-4～105 μg/L和9.80×10-5～98 μg/L, 检出限依次为0.030、 0.027、 0.029和0.022 ng/L. 使用该方法测定了多种水样中邻苯二羧酸酯类化合物.     

有序介孔碳涂层修饰固相微萃取纤维的制备及吸附性能研究

以酚醛树脂为碳源,三嵌段共聚物F127为软模板剂,制备了具有有序介孔碳涂层的固相微萃取纤维。氮气吸脱附表征表明,粉末介孔碳比表面积929 m2/g,平均孔径5.1 nm。利用气相色谱-飞行时间质谱联用技术,介孔碳涂层修饰的固相微萃取纤维对多种有机物萃取结果表明纤维对苯系物有较佳的萃取性能。介孔碳涂层是一种具有应用前景的新型固相微萃取涂层。     

新型固相微萃取涂层直接检测样品中的3种多氯酚

利用聚乙二醇2000(PEG 2000)合成了聚乙二醇硅酯预聚物,并通过溶胶-凝胶法制备了含键合聚乙二醇硅酯的固相微萃取涂层,其使用最高温度为340℃。无需衍生化的情况下,采用顶空固相微萃取结合GC/FID的方法测定3种多氯酚的检出限为0.11~0.18 ng/L;线性范围达0.1~103μg/L,相对标准偏差(RSD,n=5)为4.24%~6.44%。土样中痕量多氯酚的加标回收率分别为108%、93.5%和73.7%。     

溶胶-凝胶法制备C18固相微萃取头及其在有机氯农药残留检测中的应用

以十八烷基三乙氧基硅烷(C18-TEOS)、四乙氧基硅烷(TEOS)、乙醇、盐和水酸为原料,采用溶胶-凝胶法制备了十八烷基(C18)固相微萃取头,利用所制备萃取头实现了水样中11种有机氯农药的检测。在优化条件下,使用该萃取头对有机氯农药(OCPs)萃取后用气相色谱/电子捕获检测器(GC/ECD)测定,检出限为0.01～0.24μg/L,相对标准偏差为3.0%～13.3%。该方法用于鱼塘水、湖水及自来水中OCPs的检测,结果满意。所制备的萃取头在不同溶剂中浸泡后,对有机氯农药的萃取性能无明显变化。使用50次后,C18萃取头的萃取性能未变化。结果表明,所制备的C18固相微萃取头涂层均匀,具有多孔结构,稳定性高,有很好的实用价值。     

硫酸改性聚(甲基丙烯酸缩水甘油酯-乙二醇二甲基丙烯酸酯)固相微萃取涂层-高效液相色谱检测水中4种药品及个人护理用品

多巴胺修饰的不锈钢丝表面原位合成得到聚(甲基丙烯酸缩水甘油酯-乙二醇二甲基丙烯酸酯)(poly(GMA-EGDMA))材料,经硫酸改性后作为固相微萃取涂层,建立检测水样中4种药品及个人护理用品(PPCPs)的固相微萃取-液相色谱联用分析方法。在优化实验条件下取3 mL水样调节至pH 5.5,在30℃下,搅拌萃取60 min,乙腈-0.1%甲酸(25∶75,V/V)解吸30 min后,HPLC进样分析,实验结果表明,该涂层材料对4种PPCPs具有较好的萃取效果,2~200μg/L浓度范围内线性关系良好,相关系数均大于0.997,方法检出限(S/N=3)范围为0.5~5.0μg/L,相对标准偏差在4.1%~11.9%之间;加标实验回收率为70.6%~105.5%。本方法前处理简单、绿色环保、回收率高、精密度好,可用于实际水样中4种PPCPs的检测。     

有序介孔碳固相微萃取涂层测定水中氯苯类有机污染物

采用溶剂挥发自组装结合提拉法,在石墨纤维表面制备有序介孔碳(Ordered mesoporous cabon,OMC)涂层,并开展其对水中氯苯类有机污染物的固相微萃取(SPME)测定.扫描电镜(SEM)结果显示,制备的OMC涂层完整,与基体结合紧密,厚度约为7μm.透射电镜(TEM)、X射线衍射(XRD)和氮吸附脱附结果证实,OMC涂层具有规整二维六方特征,比表面积和孔容分别为369.7 m2/g和0.28 cm3/g.以氯苯类污染物为分析对象,采用顶空固相微萃取与氢火焰气相色谱联用法对OMC涂层的萃取性能进行全面的评价,优化萃取时间和温度、解吸时间、搅拌速率、离子强度及顶空体积等萃取条件,并与商品化涂层进行比对.结果表明,最佳萃取条件为:萃取时间30 min,萃取温度50℃,脱附时间2 min,盐浓度0.35 g/mL,顶空体积15 mL.在最佳萃取条件下,检出限在0.05～0.15 μg/L之间;在1～1000 μg/L线性范围内,线性关系良好;7次平行样测定的相对标准偏差为4.1％ ～6.4％.制备的OMC涂层的峰面积是商用聚二甲基硅氧烷/二乙烯基苯(Polydimethylsiloxane/divinylbenzene,PDMS/DVB)涂层的2倍,商用聚丙烯酸酯(Polyacrylate,PA)涂层的18倍.将此涂层应用于两种实际水样中,4种氯苯均未检出,添加浓度为20 μg/L时,样品回收率分别为99.4％～114.5％和92.3％～ 97.0％.     

分子印迹固相微萃取-高效液相色谱法测定水和牛奶中三种四环素类药物

以土霉素为模板分子制备了分子印迹固相微萃取涂层,建立了选择性萃取、高效液相色谱法同时测定牛奶和水样中四环素、盐酸土霉素和金霉素三种四环素类抗生素的分析方法。将0.1mmol盐酸土霉素在功能单体和交联剂的作用下制备分子印迹预聚合液,将经多巴胺处理后的不锈钢丝前端1~2cm置入其中,制备分子印迹固相微萃取涂层。3mL牛奶和水样经涂层萃取50min、解析5min,乙腈-10mmol/L磷酸盐缓冲液(PBS,pH=3)作为流动相,二极管阵列检测器(DAD)定量分析。实验结果表明,分子印迹涂层对四环素类目标物的特异性选择明显优于非印迹涂层。三种目标抗生素在100~1 000μg/L(牛奶)和10~1 000μg/L(水样)浓度范围内线性关系良好,相关系数在0.9959以上,四环素、盐酸土霉素和金霉素的检出限(S/N=3)为40~80μg/L(牛奶)和5~10μg/L(水样);加标水平为500μg/L时,回收率范围97.8%~109.0%,相对标准偏差(n=7)分别为5.3%~8.2%(牛奶),3.7%~6.4%(水样)。该方法前处理简单、绿色环保、选择性好、精密度好、回收率高,可用于牛奶和水样中上述三种四环素的实际检测。     

C18-MCM-41新型涂层在固相微萃取中的应用

固相微萃取（SPME）是集采样、萃取和富集于一体的样品前处理技术,该技术于1990年由Pawliszyn提出。由于其不使用有机溶剂,且简便、快速、样品用量少,因而,倍受分析工作者的青睐。     

Inorganic/organic mesoporous silica as a novel fiber coating of solid-phase microextraction

Mesoporous materials were employed as fast, sensitive and efficient fiber coatings of solid-phase microextraction (SPME) for the first time. Three micrometer as-synthesized C₁₆-MCM-41 particles were immobilized onto stainless steel wire with 100 μm coating thickness. In combination with high performance liquid chromatography (HPLC), extraction efficiency and selectivity of C₁₆-MCM-41 were investigated using aromatic hydrocarbons. Effect of extraction and desorption time, extraction temperature, stirring rate and ionic strength on extraction efficiency were examined. Aanalytical merits of SPME with C₁₆-MCM-41 coating were evaluated. The chromatographic peak area is proportional to the concentration of anthracene in the range 0.5-150 μg l⁻¹. The limit of detection was 0.05 μg l⁻¹ (S/N=3) and the relative standard deviation (R.S.D.) was 0.033%.     

石墨烯层层键合固相微萃取纤维的制备及对多环芳烃的检测

通过3-巯基丙基三甲氧基硅烷处理银层包裹的不锈钢纤维,得到Si-OH功能化的纤维,氧化石墨烯被层层键合到Si-OH功能化的纤维上,还原氧化石墨烯得到石墨烯层层键合的固相微萃取纤维。该方法制备的新型石墨烯层层键合的固相微萃取纤维具有制备简单,机械性能强,萃取涂层牢固,萃取能力强等优势。建立具有较宽线性范围(5~200μg/L)、较低检测限(0.007~0.09μg/L)的固相微萃取-气相色谱分析方法,用该方法测定河水和雨水中多环芳烃的含量。所制备的新型纤维重现性好、稳定性高、萃取能力强,可实现对多环芳烃的痕量检测。     

Highly porous silica-polyaniline nanocomposite as a novel solid-phase microextraction fiber coating

A highly porous fiber-coated SBA-15/polyaniline material was prepared for solid-phase microextraction (SPME). The SBA-15/polyaniline nanocomposite was synthesized via chemical polymerization. The prepared SBA-15/polyaniline particles were analyzed by scanning electron microscopy analysis. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. The fiber was evaluated for the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography-mass spectrometry (GC-MS). In optimum conditions (extraction temperature 60°C, extraction time 40 min, ionic strength 20%, stirring rate: 500 rpm, desorption temperature 260°C, desorption time 2 min), the repeatability for one fiber (n=3), expressed as relative standard deviation (RSD%), was between 5.3 and 8.6% for the test compounds. For deionized water, spiked with selected PAHs, the detection limits for the studied compounds were between 2 and 20 pg/mL.     

A Hexagonally Ordered Nanoporous Silica-Based Fiber Coating for SPME of Polycyclic Aromatic Hydrocarbons from Water Followed by GC�CMS

A highly porous fiber coating material was prepared and functionalized with 3-amino propyl triethoxysilane (APTES) on hexagonally ordered nanoporous silica (SBA-15). Applicability of this coating was assessed employing a laboratory made solid-phase microextraction (SPME) device and gas chromatography?Cmass spectrometry for the simultaneous sampling and determination of trace polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A one at the time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature, extraction time, ionic strength and sonication time. In the optimum conditions, the relative standard deviations for deionized water, spiked with selected PAHs were between 3.3 and 7.7% (n = 3), and detection limits for the studied compounds were 4.2 and 26.1 pg mL^?1. No significant change was observed in the extraction efficiency of the new SPME fiber, over 50 extractions. The proposed method was successfully applied to the extraction and determination of PAHs in the waste water samples.     

A Hexagonally Ordered Nanoporous Silica-Based Fiber Coating for SPME of Polycyclic Aromatic Hydrocarbons from Water Followed by GC–MS

A highly porous fiber coating material was prepared and functionalized with 3-amino propyl triethoxysilane (APTES) on hexagonally ordered nanoporous silica (SBA-15). Applicability of this coating was assessed employing a laboratory made solid-phase microextraction (SPME) device and gas chromatography–mass spectrometry for the simultaneous sampling and determination of trace polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A one at the time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature, extraction time, ionic strength and sonication time. In the optimum conditions, the relative standard deviations for deionized water, spiked with selected PAHs were between 3.3 and 7.7% (n = 3), and detection limits for the studied compounds were 4.2 and 26.1 pg mL⁻¹. No significant change was observed in the extraction efficiency of the new SPME fiber, over 50 extractions. The proposed method was successfully applied to the extraction and determination of PAHs in the waste water samples.

     

Solid-phase Microextraction with Benzoxy-calix[6]arene Fiber Coupled to Gas Chromatography for the Analysis of Polycyclic Aromatic Hydrocarbons in Water

Headspace solid-phase microextraction(HS-SPME) with sol-gel calix[6]arene-containing fiber followed by gas chromatography with a flame ionization detector was used to examine the composition and distribution of seven polycyclic aromatic hydrocarbons(PAHs) in water. The novel SPME fiber exhibited higher extraction efficiency to PAHs compared with poly(dimethylsiloxane) and other calixarene-containing fibers. Extraction/retention mechanism based on the interactions between calixarenes and PAHs was discussed. ...     

Dodecylsulfate-doped polypyrrole film prepared by electrochemical fiber coating technique for headspace solid-phase microextraction of polycyclic aromatic hydrocarbons

The electrochemical fiber coating (EFC) technique was used for the preparation of dodecylsulfate-doped polypyrrole (PPy-DS), and applied as a new fiber for solid-phase microextraction (SPME) procedures. PPy-DS film was directly electrodeposited on the surface of a platinum wire from an aqueous solution containing pyrrole and sodium dodecylsulfate, using cyclic voltammetry (CV). The effect of polymerization conditions and type of dopants on the thermal stability, adhesion and extraction characteristics of the fiber were investigated. The electron microscopy imaging of PPy-DS film suggested that the surface fiber coating was well-distributed with a porous structure. The fiber coating can be prepared easily in a reproducible manner, and it is inexpensive and has a stable performance at high temperatures (up to the 300 degrees C). The extraction properties of the fiber to eight polycyclic aromatic hydrocarbons (PAHs) were examined, using a headspace-SPME (HS-SPME) device coupled with gas chromatography-flame ionization detection (GC-FID) and gas chromatography-mass spectrometry (GC-MS). The results revealed study shows that PPy-DS as a SPME fiber coating is suitable for the successful extraction of PAHs. The effects of the extraction parameters including exposure time, sampling temperature, salt concentration, and stirring rate on the extraction efficiency have been studied. A satisfactory reproducibility for extractions from spiked water samples at PPb-level with R.S.D. < 7.6% (n = 7) was obtained. The calibration graphs were linear in the range of 0.5-100ng ml(-1) and detection limits for the selected PAHs were between 0.05-0.16 ng ml(-1). Comparing the HS-SPME results for extraction and determination of PAHs using PPy-DS fiber with the corresponding literature data using PDMS fiber shows that the proposed fiber has a better detection limit for low molecular weight PAHs. The life span and stability of PPy-DS fiber is good and it can be used more than 50 times at 250 degrees C without any significant change in sorption properties.     

聚甲基三氟丙基硅氧烷固相微萃取涂层的制备及其对海水中酚类化合物的分析

采用溶胶-凝胶技术制备了聚甲基三氟丙基硅氧烷(PTFPMS)涂层,并将其作为萃取     

Determination of polycyclic aromatic hydrocarbons in aqueous samples by microwave assisted headspace solid-phase microextraction and gas chromatography/flame ionization detection

The novel pretreatment technique, microwave-assisted heating coupled to headspace solid-phase microextraction (MA-HS-SPME) has been studied for one-step in situ sample preparation for polycyclic aromatic hydrocarbons (PAHs) in aqueous samples before gas chromatography/flame ionization detection (GC/FID). The PAHs evaporated into headspace with the water by microwave irradiation, and absorbed directly on a SPME fiber in the headspace. After being desorbed from the SPME fiber in the GC injection port, PAHs were analyzed by GC/FID. Parameters affecting extraction efficiency, such as SPME fiber coating, adsorption temperature, microwave power and irradiation time, and desorption conditions were investigated.Experimental results indicated that extraction of 20 mL aqueous sample containing PAHs at optional pH, by microwave irradiation with effective power 145 W for 30 min (the same as the extraction time), and collection with a 65 μm PDMS/DVB fiber at 20 °C circular cooling water to control sampling temperature, resulted in the best extraction efficiency. Optimum desorption of PAHs from the SPME fiber in the GC hot injection port was achieved at 290 °C for 5 min. The method was developed using spiked water sample such as field water with a range of 0.1-200 μg/L PAHs. Detection limits varied from 0.03 to 1.0 μg/L for different PAHs based on S/N = 3 and the relative standard deviations for repeatability were <13%. A real sample was collected from the scrubber water of an incineration system. PAHs of two to three rings were measured with concentrations varied from 0.35 to 7.53 μg/L. Recovery was more than 88% and R.S.D. was less than 17%. The proposed method is a simple, rapid, and organic solvent-free procedure for determination of PAHs in wastewater.