Preparation of functional ordered mesoporous carbons and their application as the QCM sensor with ultra-low humidity

Ordered mesoporous carbon (OMCs) FDU-15 was synthesized through an EISA (Evaporation-Induced Self-Assembly) method, and the oxidized OMCs (FDU-15-COOH) were obtained by subsequent oxidation treatments in liquid phase to introduce functional groups. The samples were characterized by XRD, TEM, FT-IR and nitrogen adsorption-desorption test. The low humidity sensing performances of FDU-15 and FDU-15-COOH thin films were investigated by using a quartz crystal microbalance (QCM) transducer. The responses of FDU-15-COOH is higher than that of the pristine FDU-15 at very low humidity (< 729 ppm_v) with high long-term stability, implying that FDU-15-COOH is a good candidate for low humidity QCM sensor.     

In situ AFM study of electrochemical synthesis of polypyrrole/Au nanocomposite

In this work, in situ AFM measurements with simultaneously electrochemical characterization were developed to study the mechanisms of both polypyrrole (PPy) and PPy/Au composite deposition. The nanoscale information derived from the in situ AFM images associated with theoretical simulation from the measured current–time transient (i–t) reveals that Au nanoparticles with negatively charged carboxylic groups can be the nuclei by both adsorption on the electrode surface and doping on PPy for the polymerization, and thus has faster nucleation and growth rate than Py alone at the early polymerization stage. The PPy/Au deposition shows parallel nucleation processes of Au nanoparticle and Py, and an instantaneous 3D nucleation mode. The work not only provides fundamental insights for PPy/Au nanocomposite deposition process, but also optimization approaches to fabricate a superior PPy/Au film with favorable features for greater potential applications.     

In situ monitoring of the H concentration change near an electrode surface through electrolysis using slab optical waveguide pH sensor

The H⁺ concentration change was monitored near an electrode surface through an electrolysis using a slab optical waveguide technique. Indium tin oxide transparent electrode modified by porous insulating polymer to which methyl red was covalently immobilized was used as a guiding layer, and the absorbance change of the polymer film was monitored. H⁺ generation at the vicinity of the electrode through the oxidation of ascorbic acid could be monitored by this technique.     

Novel low humidity sensor made of TiO(2) nanowires/poly(2-acrylamido-2-methylpropane sulfonate) composite material film combined with quartz crystal microbalance

A novel ceramic nanowires of TiO₂ and poly(2-acrylamido-2-methylpropane sulfonate) (TiO₂ NWs/PAMPS) composite material films coated on quartz crystal microbalance (QCM) was prepared as a low humidity sensor. The 50 wt.% of TiO₂ NWs/PAMPS composite material films showed excellent sensitivity (2.63 −ΔHz/Δppm_v) at 31.5 ppm_v), linearity (R² = 0.9959) and acceptable response time (64 s at 34.6 ppm_v). The low humidity sensing mechanism was discussed in terms of surface texture and nanostructured morphology of the composite materials. Moreover, the adsorption dynamic analysis, molecular mechanics calculation (association constant), was used to elucidate the effect of adding 50 wt.% TiO₂ NWs into PAMPS in the increased sensitivity of low humidity sensing.     

In situ Fourier Transform Infrared Spectroscopy Diagnostic for Characterization and Performance Test of Catalysts

The present work establishes a systematic approach based on the application of in-situ Fourier transform infrared spectroscopy (FTIR) for the investigation of the crystal structure, thermal stability, redox behavior (temperature-programmed reduction/temperatureprogrammed re-oxidation) as well as the catalytic properties of Co₃O₄ thin films. The syntheses of Co₃O₄ were achieved by chemical vapor deposition in the temperature range of 400-500℃. The structure analysis of the as-prepared material revealed the presence of two prominent IR bands peaking at 544 cm^-1 (υ₁) and 650 cm^-1 (υ₂) respectively, which originate from the stretching vibrations of the Co-O bond, characteristic of the Co₃O₄ spinel. The lattice stability limit of Co₃O₄ was estimated to be above 650℃. The redox properties of the spinel structure were determined by integrating the area under the emission bands υ₁ and υ₂ as a function of the temperature. Moreover, Co₃O₄ has been successfully tested as a catalyst towards complete oxidation of dimethyl ether below 340 ℃. The exhaust gas analysis during the catalytic process by in situ absorption FTIR revealed that only CO₂ and H₂O were detected as the final products in the catalytic reaction. The redox behavior suggests that the oxidation of dimethyl ether over Co₃O₄ follows a Mars-van Krevelen type mechanism. The comprehensive application of in situ FTIR provides a novel diagnostic tool in characterization and performance test of catalysts.     

Self-assembly of TiO2/polypyrrole nanocomposite ultrathin films and application for an NH3 gas sensor

TiO₂/polypyrrole (PPy) nanocomposite ultrathin films for NH₃ gas detection were fabricated by the in situ self-assembly technique. The films were characterized by UV–Vis absorption, FT–IR spectroscopy, and atomic force microscopy (AFM). The electrical properties of TiO₂/PPy ultrathin film NH₃ gas sensors, such as sensitivity, selectivity, reproducibility, and stability were investigated at room temperature in air as well as in N₂. The results showed that the optimum gas-sensing characteristics of TiO₂/PPy ultrathin film were obtained in the presence of 0.1?wt% colloidal TiO₂ for 20-min deposition. Compared with pure PPy thin-film sensors, the TiO₂/PPy film gas sensor has a shorter response/recovery time. It was also found that both humidity and temperature had an effect on the operation of the TiO₂/PPy film gas sensor at low NH₃ concentrations.     

A capacitive sensor based on molecularly imprinted polymers and poly( p -aminobenzene sulfonic acid) film for detection of pazufloxacin mesilate

A novel capacitive sensor for pazufloxacin mesilate (pazufloxacin) determination was developed by electropolymerizing p-aminobenzene sulfonic (p-ABSA) and molecularly imprinted polymers (MPs), which was synthesized through thermal radical copolymerization of metharylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA) in the presence of pazufloxacin template molecules, on the gold electrode surface. Furthermore, 1-dedecanethiol was used to insulate the modified electrode. Alternating current (ac) impedance experiments were carried out with a Model IM6e to obtain the capacitance responses. Under the optimum conditions, the sensor showed linear capacitance response to pazufloxacin in the range of 5 ng·mL⁻¹ to 5 μg·mL⁻¹ with a relative standard deviation (RSD) 5.3% (n=7) and a detection limit of 1.8 ng·mL⁻¹. The recoveries for different concentration levels of pazufloxacin samples varied from 94.0% to 102.0%. Electrochemical experiments indicated the capacitive sensor exhibited good sensitivity and selectivity and showed excellent parameters of regeneration and stability. Supported by the National Natural Science Foundation of China (Grant No. 20675064), the Natural Science Foundation of Chongqing City (Grant No. CSTC-2004BB4149 and 2005BB4100) and High Technology Project Foundation of Southwest University (Grant No. XSGX02).