Direct determination of lead in biological samples by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) after furnace-fusion in the sample cuvette-tungsten boat furnace

The newly conceived electrothermal vaporization (ETV) system using a tungsten boat furnace (TBF) sample cuvette was designed for the direct analysis of solid samples with detection by inductively coupled plasma mass spectrometry (ICP-MS). Into this small sample cuvette, a solid mixture of the biological samples and diammonium hydrogenphosphate powder as a fusion flux was placed and situated on a TBF. Tetramethylammonium hydroxide solution was added to the mixture. After the on-furnace digestion had been completed, the analyte in the cuvette was vaporized and introduced into the ICP mass spectrometer. The solid samples were analyzed by using a calibration curve prepared from the aqueous standard solutions. The detection limit was estimated to be 5.1 pg of lead, which corresponds to 10.2 ng g(-1) of lead in solid samples when a prepared sample amount of 1.0 mg was applied. The relative standard deviation for 8 replicate measurements obtained with 100 pg of lead was calculated to be 6.5%. The analytical results for various biological samples are described.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Direct determination of bromine in plastics by electrothermal vaporization/inductively coupled plasma mass spectrometry using a tungsten boat furnace vaporizer and an exchangeable sample cuvette system

A tungsten boat furnace vaporization inductively coupled plasma mass spectrometry (TBF/ICP‐MS) method has been applied to the direct determination of bromine in plastic samples. In the pretreatment, the plastic sample is spread over a small sample cuvette made of tungsten by treating it with a strongly basic organic solution, e.g., octanol or diisobutyl ketone in the presence of potassium hydroxide. The cuvette is placed on a tungsten boat furnace, with which the electrothermal vaporizer is equipped. At the vaporization step, a widely spread thin layer of the sample facilitates its efficient evaporation and introduction into an ICP mass spectrometer. The most remarkable feature is that all the bromine species in plastic samples are decomposed to form a thermally stable inorganic salt during the pretreatment procedure. Therefore, the bromine content in plastic samples can be measured by a calibration curve method constructed with an aqueous standard solution of potassium bromate(V). The detection limit (3σ) was estimated to be 0.77 pg of bromine, which corresponds to a concentration of 0.31 ng g^?1 of bromine in plastic samples when a sample amount taken of 2.5 mg is studied. The relative standard deviation was calculated to be 2.2%. Analytical results of some plastic samples, which contained both inorganic bromide salts and also organic bromine species, are given. Copyright © 2010 John Wiley & Sons, Ltd.     

Determination of Trace Chlorine in Fine Ceramics by ICP-AES Using Tungsten Boat Furnace Vaporizer and Exchangeable Sample Cuvette System as a Direct Solid Sampler

A new approach to simple solid sample digestion, subsequent vaporization, and introduction into an inductively coupled plasma was developed for the direct determination of chlorine in fine ceramic materials by atomic emission spectrometry. To each small sample cuvette made of tungsten, a powder sample was placed and weighed accurately. Following an addition of modifier solution, the cuvette was positioned on the tungsten boat furnace incorporated an electrothermal vaporizer. Then, the analyte in the sample cuvette was vaporized and introduced into the plasma; the major components of ceramic being retained. The solid ceramic samples were analyzed by using an external calibration curve prepared with the aqueous standard solutions. The detection limit of chlorine was estimated to be 0.71 ng, which corresponds to 59 ng g^?1 of the chlorine concentration in solid ceramic materials. The relative standard deviation was calculated to be 3.2%. The analytical results in various ceramic materials are described.     

Simple and convenient analytical method for the direct determination of chlorine species by ETV-ICP-AES using tungsten boat furnace vaporiser and exchangeable small sample cuvettes

A tungsten boat furnace vaporiser and an exchangeable sample cuvette system were applied for the direct determination of chlorine in plastic samples by electrothermal vaporisation inductively coupled plasma atomic emission spectrometry. Each piece of plastic samples was moulded into a thin film, and weighed into small sample cuvettes. An ethanolic solution of the modifier potassium hydroxide and an organic solvent were added to each sample cuvette. The contents including the plastic piece were spread over the bottom of each sample cuvette by warming on a hotplate. After the preparation, one of the cuvettes was placed in the tungsten boat furnace equipped with the electrothermal vaporiser. The temperature was gradually elevated. At the flash vaporisation step of 1800 °C, the analyte was vaporised and introduced into the ICP to measure an atomic emission assignable to Cl I 134.724 nm. A widely spread thin layer of the plastic facilitated its rapid evaporation and introduction into an ICP atomic emission spectrometer. Since all the chlorine species were on-furnace decomposed to form potassium chloride during the pretreatment, the solid samples were analysed using a calibration curve prepared from the aqueous standard solutions. By using this system, a detection limit of 1.5 μg g⁻¹ of chlorine in solid plastic samples was established when a sample amount taken of 2 mg was studied. The exchangeable sample cuvette technique makes it possible to measure a number of sample sequentially by preparing a lot of sample cuvettes prior to analysis. Approximately 20 batches could be vaporised per hour. Analytical results of some plastic samples that were analysed by this technique are given in this report.     

Determination of cadmium, chromium, copper and lead in sediments and soil samples by electrothermal atomic absorption spectrometry using zirconium containing chemical modifiers.

A method for direct determination of cadmium, chromium, copper and lead in sediments and soil samples by electrothermal atomic absorption spectrometry using Zr, Ir, etylenediamine acetic acid (EDTA), Zr + EDTA, Ir + EDTA, Zr + Ir and Zr + Ir + EDTA as chemical modifiers in 0.5% (v/v) Triton X-100 plus 0.2% (v/v) nitric acid mixture used as diluent was developed. The effects of mass and mass ratio of modifiers on analytes in sample solutions were studied. The optimum masses and mass ratios of modifiers: 20 microg of Zr, 4 microg of Ir, 100 microg of EDTA and 20 microg of Zr + 4 microg of Ir + 100 microg of EDTA, were used to enhance the analyte signals. Pyrolysis and atomization temperatures, atomization and background absorption profiles, characteristic masses, and detection limits of analytes in samples were compared in the presence or absence of a modifier. The detection limits and characteristic masses of analytes in a 0.5% (m/v) dissolved sample (dilution factor of 200 ml g(-1)) obtained with Zr + Ir + EDTA are 8.0 ng g(-1) and 1.2 pg for Cd, 61 ng g(-1) and 4.3 pg for Cr, 32 ng g(-1) and 23 pg for Cu, and 3.4 ng g(-1) and 19 pg for Pb, respectively. The Zr + Ir + EDTA modifier mixture was found to be preferable for the determination of analytes in sediment and soil-certified and standard reference materials. Depending on the sample type, the percent recoveries of analytes were increased from 81 to 103% by using the proposed modifier mixture; the results obtained are in good agreement with the certified values.     

Ultra-trace determination of iodine in sediments and biological material using UV photochemical generation-inductively coupled plasma mass spectrometry

Several sample preparation techniques have been evaluated for the determination of iodine using UV-photochemical generation-quadrupole inductively coupled plasma mass spectrometry. Thermal decomposition of samples at 1000 °C followed by capture of the liberated iodine in dilute acetic acid permitted subsequent UV-photochemical generation of a volatile iodine species that serves to enhance sensitivity 25-fold over conventional solution nebulization, delivering reagent blank detection limits of 8.75 pg g^{–1 127}I and 0.075 pg g^–1 129I for solid samples (400 mg test mass). The methodology was validated through determination of total iodine in several Standard Reference Materials, including NIST 1572 Citrus leaves, NIST 1549 Non-fat milk powder, NIST 1566a Oyster tissue and NIST 2709 San Joaquin Soil. Liberation of iodine from samples and its collection as well as photochemical generation were quantitative, permitting calibration to be achieved using standards prepared in dilute acetic acid.     

Determination of cadmium in biological samples solubilized with tetramethylammonium hydroxide by electrothermal atomic absorption spectrometry, using ruthenium as permanent modifier

The feasibility of Ru as a permanent modifier for the determination of Cd in biological samples treated with tetramethylammonium hydroxide (TMAH) by ET AAS was investigated. The tube treatment with Ru was carried out only once and lasted for about 300 atomization cycles. The pyrolysis and atomization temperatures, 750 °C and 1300 °C, respectively, were chosen from the temperature curves. The sample dissolution procedure was very simple: a sample aliquot was mixed with a small volume of a 25% m/v TMAH solution, the volume was made up to 50 ml and the mixture was kept at 60 °C for 1 h. Six certified biological reference materials were analyzed and the obtained Cd concentrations are within the 95% confidence interval of the certified values, proving the accuracy of the proposed procedure for a variety of biological samples. The calibration curve, with correlation coefficient higher than 0.99, was established for a working range up to10 μg l⁻¹. The precision was good as demonstrated by relative standard deviations below 3%, except for one sample. The limit of detection (3σ) was 0.05 μg l⁻¹ and the characteristic mass was 1.30 pg, obtained in the presence of the Ru modifier.     

Determination of lead in aluminum and magnesium antacids using electrothermal atomic absorption spectrometry

This paper proposes a method for the determination of lead in aluminum and magnesium antacids employing electrothermal atomic absorption spectrometry (ET AAS). The pyrolysis and atomization temperatures established during the optimization step were 700 and 2200 °C, respectively, using phosphate as the chemical modifier. Under these conditions, a characteristic mass of 25 pg, and limits of detection and quantification of 0.40 and 1.35 μg L⁻¹, respectively were obtained. Some experiments demonstrated that the calibration can be performed employing the external calibration technique using aqueous standards. The precision expressed as relative standard deviation (RSD %) was 4.03% for an antacid sample with lead concentrations of 284.5 μg L⁻¹. The proposed method was applied for the determination of lead in five antacid samples acquired in Salvador City, Brazil. The lead content was varied from 87 to 943 μg g⁻¹. The samples were also analyzed after complete dissolution by inductively coupled plasma mass spectrometry (ICP-MS). No statistical difference was observed between the results obtained by both of the procedures performed.     

Determination of traces of lead and cadmium in high-purity tin by polarized zeeman atomic-absorption spectrometry with direct atomization of solid sample in a graphite-cup cuvette

Lead at the mug g level and cadmium at ng g -mug g levels in high-purity tin have been determined by polarized Zeeman atomic-absorption spectrometry with direct atomization of the solid sample. Pieces of high-purity tin weighing up to 5 mg for lead and 20 mg for cadmium were analysed. Calibration graphs were constructed by use of standard solutions of lead and cadmium in the presence of pure tin having lead and cadmium contents below the detection limit. The tin matrix remained in the graphite-cup cuvette after atomization and did not adhere to the wall of the cuvette, so it could be easily removed and the same cuvette repeatedly used.     

Determination of uranium in marine sediment pore waters by isotope dilution inductively coupled plasma mass spectrometry

Inductively coupled plasma mass spectrometry (ICP-MS) was used in an isotope dilution mode to assay small-volume (0.25 ml) sediment pore waters for their uranium contents, using ²³⁶U as the spike. The only pretreatment required was a simple dilution by a factor of 20, which gave sufficient volume for three replicate analyses per sample. Rapid and accurate results were obtained for a variety of samples and standards, ranging in concentration from 0.05 to 10 ng U ml^?1. A suite of 30 samples can be analysed in less than 6 h by this method. The relative standard deviation was better than 1.9%, with a detection limit, based on 3σ background, of 2 pg U ml^?1 in solution (40 pg ml^?1 in samples). Sea water is a difficult matrix for ICP-MS and thus the method is generally suitable for uranium determinations in many other sample solutions.     

Determination of selenium in water and soil by hydride generation atomic absorption spectrometry using solid reagents

A hydride generation method for the determination of traces of selenium at ng mL⁻¹ concentration ranges has been introduced using a solid mixture of tartaric acid and sodium tetrahydroborate. Atomic absorption spectrometry (AAS) has been used as the detection system. Several parameters such as the ratio of tartaric acid to sodium tetrahydroborate, type and amount of acid, and the reaction temperature were optimized by using 640 ng mL⁻¹ (16 ng per 25 μL) of Se(IV) standard solution. The calibration curve was linear from 20 to 1200 ng mL⁻¹ (0.5-30 ng Se(IV) per 25 μL). The relative standard deviation (%R.S.D.) of the determination was 1.93% and the detection limit was 10.6 ng mL⁻¹ (265 pg per 25 μL) of Se(IV). The reliability of the method was checked using different types of environmental samples, such as several types of water, a sample of soil and also in a kind of calcium phosphate sample by standard addition method. For conversion of Se(VI) present in real samples to Se(IV), l-cysteine was added to NaBH₄ and tartaric acid mixture. The results showed good agreement between this method and other hydride generation techniques.     

A new approach of direct sample-digestion before vaporization for determination of a metal in rocks by inductively coupled plasma atomic emission spectrometry.

A new approach to sample digestion, subsequent vaporization and introduction to an inductively coupled plasma (ICP) atomic emission spectrometer was developed for the direct determination of magnesium. To each small sample cuvette made of tungsten, a ground rock sample was precisely weighed. The cuvette was situated on a tungsten boat furnace. Ammonium fluoride solution was added to the cuvette as a chemical modifier. After the on-furnace digestion has been completed, the analyte, magnesium, in the cuvette was vaporized and introduced into the ICP atomic emission spectrometer. Since the powdered samples were wet-digested in the sample cuvettes prior to vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of magnesium in several standard reference materials with satisfactory results.     

Preconcentration and determination of Sn- and Pb-organic species in environmental samples by SPME and GC-AED

A new sample preparation and preconcentration technique – solid phase microextraction (SPME) – is reported for the application of several tinorganic compounds and tetrabutyllead in aqueous samples. The solvent-free procedure is rapid in comparison with liquid-liquid extraction or SFE but also sensitive. Analytical variables of the extraction such as adsorption and desorption time, stirring rate and temperature has been investigated. The determination has been performed by GC coupled with atomic emission detection (AED). After optimization of the conditions of SPME a calibration was realized on the basis of a multicomponent standard solution, prepared by ethylation of organotin salts directly in the sample using sodium tetraethylborate (NaBEt₄) without prior separation of the analytes from the matrix. The method permits preconcentration. Values of about 10 can be reached. A detection limit of 0.09 pg Sn and 0.08 pg Pb can be achieved under optimized conditions. The proposed procedure has been successfully applied to the analysis of organotin compounds in various slurry samples.     

Cadmium,lead, copper and manganese determination in human deciduous teeth by electrothermal atomic absorption spectrometry using a lanthanum,palladium and citric acid mixture as chemical modifier

Cadmium, lead, copper and manganese were determined in human deciduous teeth and bone ash 1400 standard reference material by electrothermal atomic absorption spectrometry (ETAAS), using a lanthanum + palladium + citric acid (CA) modifier mixture. Optimum masses and mass ratios of La, La + Pd and La + Pd + CA modifiers for analytes in bone ash 1400 sample solution were investigated. Pyrolysis and atomization temperatures of analytes in a tooth sample solution were obtained with and without modifiers. The mixture of La + Pd + CA was found to be preferable for the determination of analytes in tooth samples and bone ash 1400, dissolved in a mixture of HNO₃ + H₂O₂. The detection limits and characteristic masses of analytes were obtained with or without modifiers based on integrated absorbance for tooth sample solution (2% m/v). The detection limits obtained with La + Pd + CA are 6,24,16 and 46 ng g^?1 for Cd, Cu, Mn and Pb, respectively. Recovery tests for analytes in bone ash 1400 and a tooth solution with La and La + Pd + CA modifier mixture were studied and compared with certified and non certified values. The La + Pd + CA mixture was also applied to the determination of Cd, Pb, Cu and Mn in tooth samples.     

Silica-coated magnetic nanoparticles modified with γ-mercaptopropyltrimethoxysilane for fast and selective solid phase extraction of trace amounts of Cd,Cu, Hg,and Pb in environmental and biological samples prior to their determination by inductively coupled plasma mass spectrometry

We report here the synthesis of a new sorbent comprising silica-coated magnetic nanoparticles (SCMNPs) modified with γ-mercaptopropyltrimethoxysilane (γ-MPTMS) for solid phase extraction of trace amounts of Cd, Cu, Hg, and Pb from biological and environmental samples. The prepared nanoparticles were characterized by infrared spectroscopy, transmission electron microscopy, and static adsorption-desorption experiments. These magnetic nanoparticles carrying the target metals could be easily separated from the aqueous solution simply by applying an external magnetic field; no filtration or centrifugation was necessary. Using this novel magnetic material, we have developed an efficient and cost-effective two-step method for detecting trace amounts of Cd, Cu, Hg, and Pb in environmental and biological samples. The first step of the method is a separation/preconcentration step, in which metals are adsorbed onto γ-MPTMS-SCMNPs. In the second step, inductively coupled plasma mass spectrometry is used to study the adsorbed metals. The effects of pH, sample volume, eluent, and interfering ions have been investigated. Under the optimized conditions, the limits of detection for Cd, Cu, Hg, and Pb were as low as 24, 92, 107, and 56 pg L^− 1, respectively. Relative standard deviations (RSDs, C = 2 ng L^− 1, n = 7) were 6.7%, 9.6%, 8.3%, and 3.7%, respectively.The proposed method has been validated using three certified reference materials, and it has been applied successfully in the determination of trace metals in biological and environmental samples.     

Standard-addition procedure for the determination of traces of lead in solid samples by x-ray fluorescence spectrometry

A standard-addition procedure for analysis of powdered solid samples by energy-dispersive X-ray fluorescence is described. Different amounts of the element to be determined are added to 4–6 specimens of the unknown sample. The spiked samples are prepared by mixing the powdered sample with an aqueous standard solution and drying the mixture. Homogeneously spiked samples are thus obtained with analyte and spike concentrations at the ppm level. The procedure has been investigated theoretically, and it is found suitable for the quantitative determination of lead at the ppm level. The accuracy of the technique for traces of lead has been tested on solid reference materials for the determination of lead. The quantitative results obtained compare well with those found by potentiometric stripping analysis.     

Study of Gaseous Sample Ionization by Excited Particles Formed in Glow Discharge Using High-Resolution Orthogonal Acceleration Time-of-Flight Mass Spectrometer

The experimental results of a mass spectral analysis of volatile organic compounds in a gaseous sample, obtained using an original design of an ion source based on the Penning ionization of a gas sample by excited metastable inert gas atoms, are presented. Using ANSYS software, a gas-dynamic simulation of reagent gas flow from discharge zone to ionization region was carried out to analyze the effect of gas flow profile on the transport of metastable atoms and ionization efficiency. The n-octane and toluene samples diluted with helium at 100 ppb mole concentrations were used for our experiments. The resulting mass spectra of n-octane and toluene samples containe far more intensive molecular ions in comparison to n-octane and toluene electron ionization mass spectra from the NIST database. The sensitivity of 5 ions per 1 pg and 130 ions per 1 pg was achieved for n-octane and toluene molecular ions using the developed ion source combined with our mass spectrometer. The corresponding detection limits are 2.3 pg s^–1 for n-octane molecular ions and 0.08 pg s^–1 for toluene molecular ions. The detection limit for the reported ion source was considered theoretically.