Experimental evidence of photoinduced valence change of Fe3+ in BaTiO3 and mechanism for growth of new grating in depleted pump condition: An EPR investigation

With a view to understanding the role of photo-induced valence changes of impurities in BaTiO₃ in the phenomena of photorefraction, EPR experiments were conducted under in situ He-Ne laser illumination. These experiments gave evidence for photoinduced valence change of Fe in BaTiO₃ at room temperature. The EPR signal due to trivalent iron was found to reduce in intensity with laser illumination The kinetics of the valence change has been investigated. Under large fringe width condition, the time constant of the decay is identified as the dielectric relaxation time τ_d. The changes in line shape on laser illumination to Dysonian form, appeared most predominantly in mechanically poled crystal compared to electrically poled single domain crystals. This demonstrated the possible role of domain walls and the defects there, as source or sinks of charge carriers on photo excitation. It is observed, that there is transient growth of Fe³⁺, when the laser illumination was put on, before its decay. This was attributed to charge transfer between electrons in oxygen vacancies and Fe⁴⁺. This predicted the growth of a transient grating under depleted pump condition in a two beam coupling experiment. This was experimentally proved by following the diffracted signal of the reading beam under the depleted pump condition.     

Upconversion emission enhancement in Er/Yb-codoped BaTiO3 nanocrystals by tridoping with Li ions

Er³⁺/Yb³⁺/Li⁺-tridoped BaTiO₃ nanocrystals were prepared by a sol-gel method to improve the upconversion (UC) luminescence of rare-earth doped BaTiO₃ nanoparticles. Effects of Li⁺ ion on the UC emission properties of the Er³⁺/Yb³⁺/Li⁺-tridoped BaTiO₃ nanocrystals were investigated. The results indicated that tridoping with Li⁺ ion enhanced the visible green and red UC emissions of Er³⁺/Yb³⁺-codoped BaTiO₃ nanocrystals under the excitation of a 976 nm laser diode. X-ray diffraction and decay time of the UC luminescence were studied to explain the reasons of the enhancement of UC emission intensity. X-ray diffraction results gave evidence that tridoping with Li⁺ ion decreased the local symmetry of crystal field around Er³⁺, which increased the intra-4f transitions of Er³⁺ ion. Moreover, lifetimes in the intermediate ⁴ S_3/2 and ⁴I_11/2 (Er) states were enhanced by Li⁺ ion incorporation in the lattice. Therefore, it can be concluded that Li⁺ ion in rare-earth doped nanocrystals is effective in enhancing the UC emission intensity.     

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

X-ray photoelectron spectroscopic (XPS) studies were carried out on wet-chemically synthesized cubic BaTiO₃, Ba_0.9Nd_0.1TiO₃ and BaTi_0.9Fe_0.1O_3−δ powders. The compounds were prepared by hydrothermal and gel to crystallite conversion technique; and phases formed readily at 420 K. The phase purity of the powders was confirmed from X-ray diffractometry. Chemical state and chemical environment of the constituent elements in the compositions were examined by XPS. Ba²⁺ was found to exist in two different chemical environments in these titanates. The Ti 2p_3/2 photoelectron peak in BaTi_0.9Fe_0.1O_3−δ was found to be broadened after Fe³⁺ substitution. Any resolvable broadening was not observed distinctly in the Ti 2p peak for Ba_0.9Nd_0.1TiO₃, unsintered BaTiO₃ and BaTiO₃ annealed in hydrogen (8% H₂ + Ar) at 1000 K. The prevalence of mixed-valent titanium and iron in BaTi_0.9Fe_0.1O_3−δ composition was evident from the XPS results and was further supported by the enhanced electrical conductivity at 298-550 K for BaTi_0.9Fe_0.1O_3−δ in comparison to BaTiO₃ and Ba_0.9Nd_0.1TiO₃. Hydroxyl incorporation was facilitated by substituting Nd³⁺ in Ba-sublattice. The presence of hydroxyls was observed from the broadening of the O 1s peak in XPS studies of the compounds.     

Effects of doping site and pre-sintering time on microstructure and magnetic properties of Fe-doped BaTiO3 ceramics

The A-site substituted BaTiO₃ ceramics were prepared by solid-state reaction via partial substitution of Fe for Ba²⁺. By comparison with the B-site substituted sample made under similar conditions, the effect of Fe doping site on microstructure and magnetism was investigated using X-ray diffraction, Mössbauer spectroscopy and vibrating sample magnetometer. It is found that A-site substitution can be realized to a certain extent at 7 at% Fe addition, whereas impurities are observed at higher Fe concentrations. In the nominal (Ba_0.93Fe_0.07)TiO₃ sample, the Fe ions are present as Fe²⁺ and Fe³⁺, respectively, replacing A-site Ba²⁺ and octahedral B-site Ti⁴⁺ in hexagonal perovskite lattice. The double-exchange Fe²⁺-O²⁻-Fe³⁺ interactions produce ferromagnetism well above room temperature, but the saturation magnetization and the Curie temperature are both obviously lower than those for B-site substitution due to different magnetic exchange mechanisms. In the B-site substituted sample Ba(Ti_0.93Fe_0.07)O₃, the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti⁴⁺ sites are responsible for ferromagnetism. These results mean that B-site substitution is a better way for Fe-doped BaTiO₃ system to obtain high-Curie-temperature ferromagnetism. Moreover, increasing pre-sintering time can further improve the magnetism of B-site substituted samples, through which the saturation magnetization for Ba(Ti_0.93Fe_0.07)O₃ is enhanced ∼6 times.     

BaTiO3晶体自抽运相位共轭特性研究

研究了多种Rh:BaTiO₃和Ce:BaTiO₃晶体样品的受激背向光折变散射自抽运相位共轭特性和响应时间特性.结果表明,入射光与晶体a面或b面法线的夹角较大时,自抽运相位共轭光有更高的反射率、更快响应时间.利用前向二波耦合特性和相向二波耦合特性对实验现象给予合理的解释.实验结果表明,多数Ce:BaTiO₃晶体比Rh:BaTiO₃晶体的共轭光反射率高. 关键词： 钛酸钡晶体 二波耦合 自抽运相位共轭 响应时间     

Fast response self-pumped phase conjugator based on a +c-face incident configuration in a pentagon-shaped BaTiO3 crystal

We propose a novel geometry for a self-pumped phase conjugator that uses a +c-face incident configuration in a photorefractive pentagon-shaped 0°-cut BaTiO₃ crystal for obtaining fast response in phase conjugation. A steady phase-conjugate output with a fast response time 0.4 s is obtained when the incident beam has a 4 W/cm² intensity. The influences of position and angle on the temporal phase-conjugate response are also investigated. The advantage of this phase conjugator using this novel configuration is improved resolution of a phase-distorted image with a value as high as 128 lp/mm.     

四方相BaTiO3缺陷性质的第一性原理计算

采用基于密度泛函理论的第一性原理方法,研究了BaTiO₃在四方相下的各种缺陷性质.计算结果表明,在富氧环境下,钛的中性氧空位、分肖特基缺陷2V^3-_Ti+3V²⁺_O形成能分别为最低;而当体系处在还原环境下时,氧空位逐渐成为主要缺陷,其形成能最低.由于四方相下存在较强的Ti—O键共价杂化,四方相下全肖特基缺陷V^2-_Ba关键词： 缺陷 第一性原理 3')" href="#">BaTiO₃     

Dielectric properties and temperature stability of BaTiO3 co-doped La2O3 and Tm2O3

The influence of La₂O₃ and Tm₂O₃ co-doping on the dielectric properties and the temperature stability of BaTiO₃ was investigated. BaTiO₃ ceramics were prepared with the compositional formula of (Ba_1−xLa_x)(Ti_1-x/4−yTm_y)O₃. La₂O₃ and Tm₂O₃ co-doping in BaTiO₃ mainly had effects on an increase in the dielectric constant and the temperature stability, respectively. The increase of La₂O₃ concentration and the decrease of Tm₂O₃ concentration in BaTiO₃ resulted in a decrease of lattice parameter and tetragonality because La³⁺ ion substituting for Ba site is smaller than Ba²⁺ ion and Tm³⁺ ion substituting for Ti site is larger than Ti⁴⁺ ion. With the increase of La₂O₃ and the decrease of Tm₂O₃, the dielectric constant of BaTiO₃ was enhanced in spite of the reduction of tetragonality. P-E hysteresis measurements revealed that this phenomenon was based on the improvement of remanent polarization with the increase of La₂O₃ concentration. The introduction of excess Tm₂O₃ in BaTiO₃ suppressed the grain growth and BaTiO₃ ceramics showed higher temperature stability due to the stable tetragonal structure and the small grain size with the increase of Tm₂O₃ concentration.     

Mechanism of enhanced photocatalysis of TiO2 by Fe in suspensions

In this work, the mechanism of enhanced photocatalysis of TiO₂ with Fe³⁺ was studied using Sulfadiazine (SD) as the model compound. Results indicated that degradation rate of SD was enhanced by the addition of Fe³⁺ in TiO₂ suspension. The crystalline structure of TiO₂ particles was stable in suspensions. The hydroxyl radical generated by TiO₂/Fe³⁺ (both TiO₂ and Fe³⁺) photocatalysis was in a higher yield. Moreover, Fe²⁺ was found not to give an obvious impact on the SD degradation in TiO₂ suspension, whereas Fe³⁺ had a notable effect. The adsorption amount of TiO₂ was greatly enhanced by the addition of Fe³⁺ in suspensions. Finally, an interaction model of SD degradation in TiO₂ suspension containing Fe³⁺ was also proposed by investigating of surface behaviors of TiO₂ particles. It will be beneficial to use Fe³⁺ as the electron acceptors on the surface of TiO₂ particles, which helps to improve the yield of hydroxyl radical.     

Surface reaction characteristics at low temperature synthesis BaTiO3 particles by barium hydroxide aqueous solution and titanium tetraisopropoxide

Well-crystallized cubic phase BaTiO₃ particles were prepared by heating the mixture of barium hydroxide aqueous solution and titania derived from the hydrolysis of titanium isopropoxide (TTIP) at 328 K, 348 K or 368 K for 24 h. The morphology and size of obtained particles depended on the reaction temperature and the Ba(OH)₂/TTIP molar ratio. By the direct hydrolytic reaction of titanium tetraisopropoxide, the high surface area titania (TiO₂) was obtained. The surface adsorption characteristics of the titania particles had been studied with different electric charges OH⁻ ions or H⁺ ions. The formation mechanism and kinetics of BaTiO₃ were examined by measuring the concentration of [Ba²⁺] ions in the solution during the heating process. The experimental results showed that the heterogeneous nucleation of BaTiO₃ occurred on the titania surface, according to the Avrami's equation.     

Tetragonal distortions of the octahedral environments of Cr3+, Fe3+ and Gd3+ ions in A2CdF4 (A = Rb,Cs) and ACdF3 crystals

Abstract

The tetragonal distortions of local octahedral environments of Cr³⁺, Fe³⁺ and Gd³⁺ ions in Rb₂CdF₄, Cs₂CdF₄, RbCdF₃ and CsCdF₃ crystals have been studied by analyzing their EPR spectra. From the studies, it is found that the tetragonal distortions for Cr³⁺ and Fe³⁺ impurity ions, which substitute Cd²⁺ and have nearly the same ionic radius, are close to each other, whereas that for Gd³⁺ impurity ion, having a larger ionic radius, is larger than those for Cr³⁺ and Fe³⁺ ions in the same crystal. It appears that not only the impurity-ligand distance, but also the tetragonal distortions of impurity centres in crystals are closely related to the size of impurity.     

Optical bistability by two laser beams in photorefractive crystals

For a nonlinear medium, a given incident laser beam may produce different transmitted light waves. This phenomenon (the so-called optical bistability) corresponds to multiple solutions of the boundary value problems of the nonlinear Helmholtz equation. Optical bistability can be useful in the design of optical switches. Devices that display this behavior could potentially play a major role in the development of optical communication systems and computing. In this article we present experimental results concerning the optical bistability in photorefractive BaTiO₃:Fe crystal. Two laser beams were used to interact with the photorefractive crystal which resulted in the bistability of the intensity of transmitted wave. This was achieved without the application of any optical resonator. High contrast optical bistability is found experimentally in the pump-ratio dependence of the output intensity.     

Iron ions in ZSM-5 zeolite: Fe3+ in framework, Fe2+ in extra-framework positions in catalytic N2O decomposition

Fe-ZSM-5 samples containing a combination of ⁵⁷Fe³⁺ in framework (FW) and regular iron in extra-framework (EFW) sites were prepared by introducing ⁵⁷Fe in hydrothermal synthesis, then exchanging Fe²⁺ of natural isotope composition into the lattice. The stability for one part of Fe²⁺ and Fe²⁺ ? Fe³⁺ reversibility for the other part in catalytic decomposition of N₂O is demonstrated by in situ Mössbaer measurements. Formation of dinuclear Fe_FW–O–Fe_EFW pairs is not prevailing.     

Preparation of Zn2+–Ni2+–Fe3+–CO32−LDHs and study of photocatalytic activities for decomposition of Methyl Orange solution

New type photocatalytic materials of Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs were prepared by complexing agent-assisted homogeneous precipitation technique and Zn(NO₃)₂·6H₂O, Ni(NO₃)·6H₂O, Fe(NO₃)₃·9H₂O used as raw materials in the case of molar ratio of Zn²⁺/Ni²⁺/Fe³⁺ = 1:6:2. Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs having a specific surface area of 96.5 m²/g. The structure and catalytic properties of the material were systematically studied. The experimental results show that the Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs has a higher adsorption performance and lower band gap which make it an excellent catalyst for reducing the degradation of the methyl orange. Study on the process of photocatalytic reaction shows that Methyl Orange was adsorbed to the layer of Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs, and then it was photodecomposed to inorganic molecules and ions by Zn²⁺, Ni²⁺, and Fe³⁺ on the surface of Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs.     

Raman study of barium titanate with oxygen vacancies

Barium titanate (BaTiO₃) crystal samples with different distribution of oxygen vacancies were prepared through different thermal treatment processes. The influences of oxygen vacancies on the Raman spectra and X-ray photoelectron spectroscopy (XPS) spectra of BaTiO₃ single crystals were studied comparatively. Raman measurements of fast-cooled BaTiO₃, which annealed in vacuum and then cooled in air showed many different spectroscopic results comparing with as-received BaTiO₃ sample. Raman measurements of slow-cooled BaTiO₃, which annealed in vacuum and then cooled in tube furnace exhibited few spectroscopic differences. XPS measurements of as-received BaTiO₃ sample and fast-cooled BaTiO₃ sample confirmed that this discrepancy resulted from the surface phase of oxygen vacancy in BaTiO₃.     

Fe掺杂量对双层复合结构BaTi1-zFezO3+δ-Tb1-xDyxFe2-y中磁电耦合的影响

采用溶胶凝胶方法制备了Fe掺杂钛酸钡多晶系列陶瓷BaTi_1-zFe_zO_3+δ(0.005≤z≤0.02) (BTFO).X射线衍射实验显示,所制备的BTFO的结构仍然为四方相钙钛矿.差热分析表明,该BTFO样品的铁电-顺电转变温度及相变潜热随掺杂量z的增加而下降.将该BTFO极化后与Tb_1-xDy_xF 关键词： 磁电耦合 掺杂效应 掺杂钛酸钡     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

蓝宝石(α-Al_2O_3:Fe~(3+))体系基态分裂与局域晶格畸变的研究

2002年Scholz和Buzaré对蓝宝石晶体中Fe3+离子的基态分裂重新进行了EPR实验测量和研究,他们的初步分析表明在蓝宝石晶体中Fe3+离子的6A1基态分裂有可能同时与两个方向的畸变角(θ和φ)有关.本文采用对角化d5组态在C3点群对称下的252×252完全能量矩阵的方法,对蓝宝石晶体中Fe3+离子的光谱和EPR谱进行了系统的研究.计算结果表明蓝宝石体系中Fe3+离子的6A1基态分裂确实将明显依赖于两个方向的畸变角θ和φ,这一理论结果与Scholz和Buzaré等的实验相符合.同时,通过拟合Fe3+离子在蓝宝石体系中的实验光谱和EPR参量,确定了蓝宝石晶体中(FeO6)9团簇局域晶格畸变角θi的范围.     

Synthesis and characteristics of natural zeolite supported Fe-TiO2 photocatalysts

Natural zeolite supported Fe³⁺-TiO₂ photocatalysts were synthesized for the sake of improving the recovery and photocatalytic efficiency of TiO₂. The as-prepared materials were characterized by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), ultraviolet-visible diffuse reflection spectroscopy (UV-vis DRS), scanning electron microscopy (SEM) and energy-dispersive X-ray analysis (EDX). Methyl orange was used to estimate the photocatalytic activity of the samples. The results showed that zeolite inhibited the growth of TiO₂ crystallite sizes. The Fe³⁺ concentration played an important role on the microstructure and photocatalytic activity of the samples. The iron ions could diffuse into TiO₂ lattice to the form Fe-O-Ti bond and gave TiO₂ the capacity to absorb light at lower energy levels. The photocatalytic activity of the samples could be enhanced as appropriate dosages of Fe³⁺ were doped.     

Theoretical studies of the optical and EPR spectra for Fe ion in the MF3:Fe (M=Al, Ga) systems

By analyzing the EPR spectra of Fe³⁺ ion in the fluorinde glasses, the local lattice structures around impurity Fe³⁺ ion in MF₃:Fe³⁺ (M=Al, Ga) systems have been studied by means of diagonalizing the complete energy matrices of the electron-electron repulsion, the ligand-field and the spin-orbit coupling for a d⁵ configuration ion in a trigonal ligand-field. Both the second-order and fourth-order EPR parameters D and (a−F) are taken simultaneously in the structural investigation. The results indicate that the local lattice structure around octahedral Fe³⁺ center has an expansion distortion for Fe³⁺ in MF₃:Fe³⁺ (M=Al, Ga). The expansion distortion may be ascribed to the fact that the radius of Fe³⁺ ion is larger than that of Al³⁺ ion and Ga³⁺ ion, and the Fe³⁺ ion will push the fluoride ligands upwards and downwards, respectively. The local lattice structure parameters R=1.927 A, θ=55.538° for Fe³⁺ in AlF₃:Fe³⁺ and R=1.931 A, θ=56.09° for Fe³⁺ in GaF₃:Fe³⁺ are determined, respectively, and the EPR spectra of the MF₃:Fe³⁺ (M=Al, Ga) systems are satisfactorily explained.