Catalytic Chemistry Derived Artificial Solid Electrolyte Interphase for Stable Lithium Metal Anodes Working at 20 mA cm−2 and 20 mAh cm−2

A stable solid electrolyte interphase (SEI) layer is crucial for lithium metal anode (LMA) to survive in long-term cycling. However, chaotic structures and chemical inhomogeneity of natural SEI make LMA suffering from exasperating dendrite growth and severe electrode pulverization, which hinder the practical application of LMAs. Here, we design a catalyst-derived artificial SEI layer with an ordered polyamide-lithium hydroxide (PA-LiOH) bi-phase structure to modulate ion transport and enable dendrite-free Li deposition. The PA-LiOH layer can substantially suppress the volume changes of LMA during Li plating/stripping cycles, as well as alleviate the parasitic reactions between LMA and electrolyte. The optimized LMAs demonstrate excellent stability in Li plating/stripping cycles for over 1000 hours at an ultra-high current density of 20 mA cm⁻² in Li||Li symmetric cells. A high coulombic efficiency up to 99.2 % in Li half cells in additive-free electrolytes is achieved even after 500 cycles at a current density of 1 mA cm⁻² with a capacity of 1 mAh cm⁻².     

金属锂负极失效机制及其先进表征技术

尽管传统的石墨负极在商业化锂离子电池中取得了成功,但其理论容量低(372 mAh·g^?1)、本身不含锂的先天缺陷限制了其在下一代高比能量锂电池体系中的应用,特别是在需要锂源的锂-硫和锂-空气电池体系中。金属锂因其极高的理论比容量(3860 mAh·g^?1)和低氧化还原电势(相对于标准氢电极为?3.040 V),被认为是下一代锂电池负极材料的最佳选择之一。但是,金属锂负极存在库伦效率低、循环性能差、安全性差等一系列瓶颈问题亟待解决,而循环过程中锂枝晶的生长、巨大的体积变化、以及电极界面不稳定等是导致这些问题的关键因素。本文综述了近年来关于金属锂负极瓶颈问题及其机理,包括金属锂电极表面固态电解质界面膜的形成,锂枝晶的生长行为,以及惰性死锂的形成。同时,本文还介绍了目前用于研究金属锂负极的先进表征技术,这些技术为研究人员深入认识金属锂负极的失效机制提供了重要信息。     

A novel high-energy-density lithium-free anode dual-ion battery and in situ revealing the interface structure evolution

Lithium-free anode dual-ion batteries have attracted extensive studies due to their simple configuration, reduced cost, high safety and enhanced energy density. For the first time, a novel Li-free DIB based on a carbon paper anode (Li-free CGDIB) is reported in this paper. Carbon paper anodes usually have limited application in DIBs due to their poor electrochemical performance. Herein, by using a lithium bis(fluorosulfonyl)imide (LiFSI)-containing electrolyte, the battery shows outstanding electrochemical performance with a capacity retention of 96% after 300 cycles at 2C with a stable 98% coulombic efficiency and 89% capacity retention after 500 cycles at 5C with a stable coulombic efficiency of 98.5%. Moreover, the electrochemical properties of the CGDIB were investigated with a variety of in situ characterization techniques, such as in situ EIS, XRD and online differential electrochemical mass spectrometry (OEMS). The multifunctional effect of the LiFSI additive on the electrochemical properties of the Li-free CGDIB was also systematically analyzed, including generating a LiF-rich interfacial film, prohibiting Li dendrite growth effectively and forming a defective structure of graphite layers. This design strategy and fundamental analysis show great potential and lay a theoretical foundation for facilitating the further development of DIBs with high energy density.

A novel lithium-free anode dual-ion battery is fabricated based on a carbon paper anode. In situ EIS, XRD and OEMS demonstrate the multi-functional effects of LiFSI on the performance of the Li-free CGDIB.     

Inhibition of lithium dendrites and dead lithium by an ionic liquid additive toward safe and stable lithium metal anodes

The uncontrolled growth of lithium dendrites and accumulation of “dead lithium” upon cycling are among the main obstacles that hinder the widespread application of lithium metal anodes. Herein, an ionic liquid (IL) consisting of 1-methyl-1-propylpiperidinium cation (Pp₁₃⁺) and bis(fluorosulfonyl)imide anion (FSI^?), was chosen as the additive in propylene carbonate (PC)-based liquid electrolytes to circumvent the shortcoming of lithium metal anodes. The optimal 1% Pp₁₃FSI acts as the role of electrostatic shielding, lithiophobic effect and participating in the formation of solid electrolyte interface (SEI) layer with enhanced properties. The in-situ optical microscopy records that the addition of IL can effectively inhibit the growth of lithium dendrites and the corrosion of lithium anode. This study delivers an effective modification to optimize electrolytes for stable lithium metal batteries.     

The understanding of solid electrolyte interface (SEI) formation and mechanism as the effect of flouro-o-phenylenedimaleimaide (F-MI) additive on lithium-ion battery

Solid electrolyte interface (SEI) is a critical factor that influences battery performance. SEI layer is formed by the decomposition of organic and inorganic compounds after the first cycle. This study investigates SEI formation as a product of electrolyte decomposition by the presence of flouro-o-phenylenedimaleimaide (F-MI) additive. The presence of fluorine on the maleimide-based additive can increase storage capacity and reversible discharge capacity due to high electronegativity and high electron-withdrawing group. The electrolyte containing 0.1 wt% of F-MI-based additive can trigger the formation of SEI, which could suppress the decomposition of remaining electrolyte. The reduction potential was 2.35 to 2.21 V vs Li/Li⁺ as examined by cyclic voltammetry (CV). The mesocarbon microbeads (MCMB) cell with F-MI additive showed the lowest SEI resistance (Rsei) at 5898 Ω as evaluated by the electrochemical impedance spectroscopy (EIS). The morphology and element analysis on the negative electrode after the first charge-discharge cycle were examined by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS). XPS result showed that MCMB cell with F-MI additive provides a higher intensity of organic compounds (RCH₂OCO₂Li) and thinner SEI than MCMB cell without an additive that provides a higher intensity of inorganic compound (Li₂CO₃ and Li₂O), which leads to the performance decay. It is concluded that attaching the fluorine functional group on the maleimide-based additive forms the ideal SEI formation for lithium-ion battery.     

Facile Stabilization of the Sodium Metal Anode with Additives: Unexpected Key Role of Sodium Polysulfide and Adverse Effect of Sodium Nitrate

Sodium metal is an attractive anode for next‐generation energy storage systems owing to its high specific capacity, low cost, and high abundance. Nevertheless, uncontrolled Na dendrite growth caused by the formation of unstable solid electrolyte interphase (SEI) leads to poor cycling performance and severe safety concerns. Sodium polysulfide (Na₂S₆) alone is revealed to serve as a positive additive or pre‐passivation agent in ether electrolyte to improve the long‐term stability and reversibility of the Na anode, while Na₂S₆‐NaNO₃ as co‐additive has an adverse effect, contrary to the prior findings in the lithium anode system. A superior cycling behavior of Na anode is first demonstrated at a current density up to 10 mA cm^?2 and a capacity up to 5 mAh cm^?2 over 100 cycles. As a proof of concept, a high‐capacity Na‐S battery was prepared by pre‐passivating the Na anode with Na₂S₆. This study gives insights into understanding the differences between Li and Na systems.     

Investigation of interfacial processes in graphite thin film anodes of lithium-ion batteries by both in situ and ex situ infrared spectroscopy

Graphite thin film anodes with a high IR reflectivity have been prepared by a spin coating method. Both ex situ and in situ microscope FTIR spectroscopy (MFTIRS) in a reflection configuration were employed to investigate interfacial processes of the graphite thin film anodes in lithium-ion batteries. A solid electrolyte interphase layer (SEI layer) was formed on the cycled graphite thin film anode. Ex situ MFTIRS revealed that the main components of the SEI layer on cycled graphite film anodes in 1 mol L -1 LiPF6 /ethylene carbonate + dimethyl carbonate (1:1) are alkyl lithium carbonates (ROCO2 Li). The desolvation process on graphite anodes during the initial intercalation of lithium ion with graphite was also observed and analyzed by in situ MFTIRS.     

Morphology and modulus evolution of graphite anode in lithium ion battery: An in situ AFM investigation

We investigated the interfacial electrochemical processes on graphite anode of lithium ion battery by using highly oriented pyrolytic graphite(HOPG)as a model system.In situ electrochemical atomic force microscopy experiments were performed in 1M lithium bis(trifluoromethanesulfonyl)imide/ethylene carbonate/diethyl carbonate to reveal the formation process of solid electrolyte interphase(SEI)on HOPG basal plane during potential variation.At 1.45 V,the initial deposition of SEI began at the defects of HOPG surface.After that,direct solvent decomposition took place at about 1.3 V,and the whole surface was covered with SEI.The thickness of SEI was 10.4±0.2 nm after one cycle,and increased to 13.8±0.2 nm in the second cycle,which is due to the insufficient electron blocking ability of the surface film.The Young’s modulus of SEI was measured by a peak force quantitative nanomechanical mapping(QNM).The Young’s modulus of SEI is inhomogeneous.The statistic value is 45±22 MPa,which is in agreement with the organic property of SEI on basal plane of HOPG.     

计算模拟在锂金属负极研究中的应用

锂金属以其高比容量和低电极电势,在高能量密度电池领域具有极大潜力,然而界面反应复杂、枝晶生长难以抑制等问题,导致电池易燃易爆、容易击穿短路,极大地限制了锂电池的应用。计算模拟有助于科研工作者认识反应机理、预测筛选电极材料以及优化电池设计,与实验相辅相成。本文对近年计算模拟在锂金属电极中的应用进行综述,重点在于利用分子动力学、第一性原理计算等计算方法,研究界面反应、固体电解质膜以及锂形核。此外,新开发的固态电解质很好地解决了传统锂电池易燃易爆等问题,提高了能量密度,但也存在界面阻力大、传导性能差以及枝晶生长等问题,对此,我们就计算模拟在固态电解质锂电池中锂负极的应用进行综述。最后,我们论述了该领域潜在研究方向。     

Effects of Solid Electrolyte Interphase Components on the Reduction of LiFSI over Lithium Metal

The use of a lithium metal anode still presents a challenging chemistry and engineering problem that holds back next generation lithium battery technology. One of the issues facing lithium metal is the presence of the solid electrolyte interphase (SEI) layer that forms on the electrode creating a variety of chemical species that change the properties of the electrode and is closely related to the formation and growth of lithium dendrites. In order to advance the scientific progress of lithium metal more must be understood about the fundamentals of the SEI. One property of the SEI that is particularly critical is the passivating behavior of the different SEI components. This property is critical to the continued formation of SEI and stability of the electrolyte and electrode. Here we report the investigation of the passivation behavior of Li₂O, Li₂CO_3, LiF and LiOH with the lithium salt LiFSI. We used large computational chemistry models that are able to capture the lithium/SEI interface as well as the SEI/electrolyte interface. We determined that LiF and Li₂CO₃ are the most passivating of the SEI layers, followed by LiOH and Li₂O. These results match previous studies of other Li salts and provide further examination of LiFSI reduction.     

Fluoroethylene Carbonate Enabling a Robust LiF‐rich Solid Electrolyte Interphase to Enhance the Stability of the MoS2 Anode for Lithium‐Ion Storage

As a high‐capacity anode for lithium‐ion batteries (LIBs), MoS₂ suffers from short lifespan that is due in part to its unstable solid electrolyte interphase (SEI). The cycle life of MoS₂ can be greatly extended by manipulating the SEI with a fluoroethylene carbonate (FEC) additive. The capacity of MoS₂ in the electrolyte with 10 wt % FEC stabilizes at about 770 mAh g^?1 for 200 cycles at 1 A g^?1, which far surpasses the FEC‐free counterpart (ca. 40 mAh g^?1 after 150 cycles). The presence of FEC enables a robust LiF‐rich SEI that can effectively inhibit the continual electrolyte decomposition. A full cell with a LiNi_0.5Co_0.3Mn_0.2O₂ cathode also gains improved performance in the FEC‐containing electrolyte. These findings reveal the importance of controlling SEI formation on MoS₂ toward promoted lithium storage, opening a new avenue for developing metal sulfides as high‐capacity electrodes for LIBs.     

In situ AFM studies of SEI formation at a Sn electrode

Early stages of the solid electrolyte interphase (SEI) formation at a tin foil electrode in an ethylene carbonate (EC) based electrolyte were investigated by in situ AFM and cyclic voltammetry (CV) at potentials >0.7 V, i.e., above the potential of Sn–Li alloying. We detected and observed initial steps of the surface film formation at ～2.8 V vs. Li/Li⁺ followed by gradual film morphology changes at potentials 0.7 < U < 2.5 V. The SEI layer undergoes continuous reformation during the following CV cycles between 0.7 and 2.5 V. The surface film on Sn does not effectively prevent the electrolyte reduction and a large fraction of the reaction products dissolve in the electrolyte. The unstable SEI layer on Sn in EC-based electrolytes may compromise the use of tin-based anodes in Li-ion battery systems unless the interfacial chemistry of the electrode and/or electrolyte is modified.     

多酚类化合物—丹宁酸用作锂金属负极电解液成膜添加剂

As the application of lithium-ion batteries in advanced consumer electronics, energy storage systems, plug-in hybrid electric vehicles, and electric vehicles increases, there has emerged an urgent need for increasing the energy density of such batteries. Lithium metal anode is considered as the "Holy Grail" for high-energy-density electrochemical energy storage systems because of its low reduction potential (-3.04 V vs standard hydrogen electrode) and high theoretical specific capacity (3860 mAh·g^-1). However, the practical application of lithium metal anode in rechargeable batteries is severely limited by irregular lithium dendrite growth and high reactivity with the electrolytes, leading to poor safety performance and low coulombic efficiency. Recent research progress has been well documented to suppress dendrite growth for achieving long-term stability of lithium anode, such as building artificial protection layers, developing novel electrolyte additives, constructing solid electrolytes, using functional separator, designing composite electrode or three-dimensional lithium-hosted material. Among them, the use of electrolyte additives is regarded as one of the most effective and economical methods to improve the performance of lithium-ion batteries. As a natural polyphenol compound, tannic acid (TA) is significantly cheaper and more abundant compared with dopamine, which is widely used for the material preparation and modification in the field of lithium-ion batteries. Herein, TA is first reported as an efficient electrolyte film-forming additive for lithium metal anode. By adding 0.15% (mass fraction, wt.) TA into the base electrolyte of 1 mol·L^-1 LiPF₆-EC/DMC/EMC (1 : 1 : 1, by wt.), the symmetric Li|Li cell exhibited a more stable cyclability of 270 h than that of only 170 h observed for the Li|Li cell without TA under the same current density of 1 mA·cm^-2 and capacity of 1 mAh·cm^-2 (with a cutoff voltage of 0.1 V). Electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV), and energy-dispersive X-ray spectroscopy (EDS) analyses demonstrated that TA participated in the formation of a dense solid electrolyte interface (SEI) layer on the surface of the lithium metal. A possible reaction mechanism is proposed here, wherein the small amount of added polyphenol compound could have facilitated the formation of LiF through the hydrolysis of LiPF₆, following which the resulting phenoxide could react with dimethyl carbonate (DMC) through transesterification to form a cross-linked polymer, thereby forming a unique organic/inorganic composite SEI film that significantly improved the electrochemical performance of the lithium metal anode. These results demonstrate that TA can be used as a promising film-forming additive for the lithium metal anode.     

Highly Stable Lithium Metal Batteries Enabled by Regulating the Solvation of Lithium Ions in Nonaqueous Electrolytes

Safe and rechargeable lithium metal batteries have been difficult to achieve because of the formation of lithium dendrites. Herein an emerging electrolyte based on a simple solvation strategy is proposed for highly stable lithium metal anodes in both coin and pouch cells. Fluoroethylene carbonate (FEC) and lithium nitrate (LiNO₃) were concurrently introduced into an electrolyte, thus altering the solvation sheath of lithium ions, and forming a uniform solid electrolyte interphase (SEI), with an abundance of LiF and LiN_xO_y on a working lithium metal anode with dendrite‐free lithium deposition. Ultrahigh Coulombic efficiency (99.96 %) and long lifespans (1000 cycles) were achieved when the FEC/LiNO₃ electrolyte was applied in working batteries. The solvation chemistry of electrolyte was further explored by molecular dynamics simulations and first‐principles calculations. This work provides insight into understanding the critical role of the solvation of lithium ions in forming the SEI and delivering an effective route to optimize electrolytes for safe lithium metal batteries.     

电解液添加剂硫酸亚乙酯对锂离子电池性能的影响

在1 mol/L LiPF₆/碳酸乙烯酯+碳酸二甲酯+碳酸甲乙酯（体积比1∶1∶1）电解液中,采用恒流充放电测试、循环伏安法（CV）、扫描电子显微镜（SEM）、能量散射光谱（EDS）、电化学阻抗谱（EIS）等测试技术,研究了添加剂硫酸亚乙酯（DTD）对锂离子电池性能及石墨化中间相碳微球（MCMB）电极/电解液界面性质的影响。 结果表明,在电解液中引入体积分数0.01%DTD后,MCMB/Li电池可逆放电容量从300 mA·h/g提高至350 mA·h/g,电池总阻抗降低,循环稳定性提高。CV测试发现,在首次还原过程中,DTD在电极电位1.4 V左右（vs Li/Li⁺）发生电化学还原,参与了MCMB电极表面固体电解质相界面膜（SEI膜）的形成过程。 同时,DTD对LiMn₂O₄电极性能无不良影响。     

Lithium Bis(oxalate)borate Additive for Self-repairing Zincophilic Solid Electrolyte Interphases towards Ultrahigh-rate and Ultra-stable Zinc Anodes

The artificial solid electrolyte interphase (SEI) plays a pivotal role in Zn anode stabilization but its long-term effectiveness at high rates is still challenged. Herein, to achieve superior long-life and high-rate Zn anode, an exquisite electrolyte additive, lithium bis(oxalate)borate (LiBOB), is proposed to in situ derive a highly Zn²⁺-conductive SEI and to dynamically patrol its cycling-initiated defects. Profiting from the as-constructed real-time, automatic SEI repairing mechanism, the Zn anode can be cycled with distinct reversibility over 1800 h at an ultrahigh current density of 50 mA cm⁻², presenting a record-high cumulative capacity up to 45 Ah cm⁻². The superiority of the formulated electrolyte is further demonstrated in the Zn||MnO₂ and Zn||NaV₃O₈ full batteries, even when tested under harsh conditions (limited Zn supply (N/P≈3), 2500 cycles). This work brings inspiration for developing fast-charging Zn batteries toward grid-scale storage of renewable energy sources.     

Electrolyte additive maintains high performance for dendrite-free lithium metal anode

Because of their high capacity and low potential, lithium metal anodes are considered to be promising candidates for next generation electrode materials. However, the safety concerns and limited cycling life associated with uncontrollable dendrite growth hamper practical applications. In this work, the acidified cellulose ester, which is a mixed fiber microporous membrane film, was used as a novel electrolyte additive that effectively improves the cycle stability of the lithium metal anode and inhibits dendrite growth. The focus of this paper is on inhibiting the formation and growth of lithium dendrites. The coulombic efficiency of a Li|Cu battery with this acidified cellulose ester additive remains stable at 99% after 500 cycles under a current density of 1 mA/cm². Symmetric batteries also remain stable after 500 cycles (1000 h) under a current density of 1 mA/cm². These superior properties can be ascribed to the induced nucleation and the uniform distribution of lithium ion flux. This study uncovers an approach for effectively enabling stable cycling of dendrite-free lithium metal anodes.     

A Liquid/Liquid Electrolyte Interface that Inhibits Corrosion and Dendrite Growth of Lithium in Lithium-Metal Batteries

A proof-of-concept study on a liquid/liquid (L/L) two-phase electrolyte interface is reported by using the polarity difference of solvent for the protection of Li-metal anode with long-term operation over 2000 h. The L/L electrolyte interface constructed by non-polar fluorosilicane (PFTOS) and conventionally polar dimethyl sulfoxide solvents can block direct contact between conventional electrolyte and Li anode, and consequently their side reactions can be significantly eliminated. Moreover, the homogeneous Li-ion flow and Li-mass deposition can be realized by the formation of a thin and uniform solid-electrolyte interphase (SEI) composed of LiF, Li_xC, Li_xSiO_y between PFTOS and Li anode, as well as the super-wettability state of PFTOS to Li anode, resulting in the suppression of Li dendrite formation. The cycling stability in a lithium–oxygen battery as a model is improved 4 times with the L/L electrolyte interface.     

Lithium Azide as an Electrolyte Additive for All‐Solid‐State Lithium–Sulfur Batteries

Of the various beyond‐lithium‐ion battery technologies, lithium–sulfur (Li–S) batteries have an appealing theoretical energy density and are being intensely investigated as next‐generation rechargeable lithium‐metal batteries. However, the stability of the lithium‐metal (Li°) anode is among the most urgent challenges that need to be addressed to ensure the long‐term stability of Li–S batteries. Herein, we report lithium azide (LiN₃) as a novel electrolyte additive for all‐solid‐state Li–S batteries (ASSLSBs). It results in the formation of a thin, compact and highly conductive passivation layer on the Li° anode, thereby avoiding dendrite formation, and polysulfide shuttling. It greatly enhances the cycling performance, Coulombic and energy efficiencies of ASSLSBs, outperforming the state‐of‐the‐art additive lithium nitrate (LiNO₃).     

Interfacial Evolution of Lithium Dendrites and Their Solid Electrolyte Interphase Shells of Quasi‐Solid‐State Lithium‐Metal Batteries

Unstable electrode/solid‐state electrolyte interfaces and internal lithium dendrite penetration hamper the applications of solid‐state lithium‐metal batteries (SSLMBs), and the underlying mechanisms are not well understood. Herein, in situ optical microscopy provides insights into the lithium plating/stripping processes in a gel polymer electrolyte and reveals its dynamic evolution. Spherical lithium deposits evolve into moss‐like and branch‐shaped lithium dendrites with increasing current densities. Remarkably, the on‐site‐formed solid electrolyte interphase (SEI) shell on the lithium dendrite is distinctly captured after lithium stripping. Inducing an on‐site‐formed SEI shell with an enhanced modulus to wrap the lithium precipitation densely and uniformly can regulate dendrite‐free behaviors. An in‐depth understanding of lithium dendrite evolution and its functional SEI shell will aid in the optimization of SSLMBs.