海藻酸钠固定化根霉脂肪酶的制备及其性质

 研究了以海藻酸钠为载体,用包埋法制备固定化德氏根霉(Rhizopus delemar)脂肪酶的条件. 将酶粉和海藻酸钠溶于pH 5.0的HAc-NaAc缓冲溶液,用注射器将此混合液滴入到0.05 mol/L无菌CaCl2溶液中,静置固化45 min, 经过滤、洗涤和干燥后得到球状固定化酶. 固定化酶的活力回收约为34.1%. 酶学性质研究表明,此固定化酶的热稳定性较好. 游离酶在 60 ℃下保温1 h已完全丧失活力,而固定化酶在100 ℃下保温1 h仅损失36.2%的活力,在100 ℃下保温6 h仍可保持46.8%的酶活力. 酶经固定化后,其橄榄油水解反应的最适温度由40 ℃上升至90 ℃, Km值由13.8 mg/ml下降为8.1 mg/ml. 常见有机溶剂对固定化酶的活力影响较小. 将该固定化脂肪酶用于非水溶剂中正戊酸异戊酯的合成,重复使用6次后,固定化酶仍保持95%的酶活力.     

固定化扩展青霉脂肪酶的制备及其在玉米油转酯反应中的应用

采用吸附法对来源于扩展青霉Penicillium expansum的脂肪酶进行了固定化.从20种不同来源的树脂中筛选出固定化效率高且价格低廉的D4020树脂作为载体,系统研究了固定化条件对固定化效率及固定化酶转酯活力的影响.结果表明,最适加酶量、缓冲液pH和吸附时间分别为0.7 g/g、9.4和4 h.冻干时添加0.5%的半乳糖有助于提高固定化酶的转酯活力.在上述优化条件下,固定化酶的转酯活力为404.0 U/g,而所用的游离酶不能催化该转酯反应.利用该固定化酶催化玉米油转酯反应生产生物柴油时,叔戊醇为适宜的反应介质,其最适添加量为0.5 ml/g;适宜的酶量、加水量和反应温度分别为60.6 U/g、油重的1.2%和35℃.按醇/油摩尔比为1的比例分别在反应0、2和6 h时加入甲醇,在优化反应条件下,反应24 h后甲酯产率达85.0%;固定化脂肪酶具有较好的操作稳定性,反应10批次时,相对酶活力为62.8%.     

壳聚糖固定化乳酸脱氢酶的制备及酶学性质研究

以磁性壳聚糖作为载体,戊二醛作为交联剂,对乳酸脱氢酶(LDH)进行固定化.固定化的最适条件为:戊二醛浓度6%,pH值7.5,酶的偶联时间2 h.对游离及固定化LDH酶学性质的研究表明,酶促反应的最适pH值为9.2,最适温度分别为37℃和50℃,对乳酸的表观米氏常数分别为1.6 mmol/L和0.9 mmol/L.游离酶和固定化酶在40℃放置150 min后,其活力分别为最初的56.5%和76.1%.固定化酶在4℃贮存4周后,活力仍保留50%以上.固定化酶在室温下与底物重复反应6次后,活力仍保留60%以上,说明固定化酶具有较好的热稳定性、贮存稳定性和复用性.     

壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶及其性质

以具柔性亲水手臂的壳聚糖-精氨酸树脂为载体,用戊二醛交联胰凝乳蛋白酶,获得壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶. 最佳固定化条件为:m(酶)∶ m(载体)=20∶ 1 000、戊二醛体积分数为1.0%、pH=5.20、30 ℃交联60 min. 固定化酶活力达850 U/g,Km为1.83 mmol/L,比游离酶增大33.6%,比交联壳聚糖固定化酶低24.0%. 壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶水解时间进程曲线与游离酶基本一致,均在反应30 min达到最大速率,最适温度为70 ℃,比游离酶升高10 ℃;在75 ℃时的半衰期可达6.0 h,比游离酶提高约4.3倍;最适pH值为5.92,比游离酶向酸性偏移2pH单位. 4 ℃贮存半衰期为49 d.     

漆酶在纳米多孔金上的固定化及其酶学性质研究

利用纳米材料为载体对酶等生物大分子进行固定化近年来引起人们的浓厚兴趣. 以Au/Ag合金为原料, 通过控制浓硝酸的腐蚀时间再辅以退火处理得到了不同孔径的纳米多孔金(NPG), 利用扫描电镜(SEM)和N2气体吸附仪对孔性质进行了表征. 以NPG为载体, 用α-硫辛酸和N-乙基-N’-(3-二甲基氨基丙基)碳酰二亚胺/N-羟基琥珀酰亚胺(EDC/NHS)对金表面进行活化, 通过化学共价偶联的方法对产自Trametes versicolor的漆酶进行了固定化. 比较了孔径大小对酶固定化量及比活力的影响. 发现小孔径更有利于对该漆酶的固定化. 与游离酶相比, 固定化酶的最适pH没有改变, 但最适温度却从原来的40 ℃升到了60 ℃. 固定化后, 漆酶的pH和热稳定性都明显提高了. 重复使用8次仍能保持初始活力的65%, 且在4 ℃下保存1个月几乎观察不到酶活力的下降. 此外, 失活的固定化酶经浓硝酸处理后, NPG载体可重复利用. 本结果初步显示出了NPG在生物技术领域中的应用潜力.     

海藻酸钙凝胶包埋乳酸氧化酶催化DL-乳酸生产丙酮酸

研究了用海藻酸钠包埋、戊二醛交联法固定耻垢分枝杆菌(Mycobacterium Srnegmatis)生成乳酸氧化酶的最佳条件,比较了原酶与固定化酶的酶学性质.将1mL酶液和1 mL质量分数为3%的海藻酸钠溶液的混合液,用注射器滴加到20 mL0.2 mol/L.的CaCl2溶液中,25℃静置固化2 h后,过滤洗涤,将同体转移至20 mL质量分数为0.2%戊二醛溶液中37℃交联2 h后,过滤、洗涤和干燥得到球状同定化酶.固定化酶的活力回收率为39.8%.酶学性质研究表明,此固定化酶的热稳定性较好,游离酶在65 ℃保温l h酶蛋白完全变性失活,而固定化酶在65℃保温1 h仍可保持86%的酶活力;其最适酶促反应温度可由37℃升至55℃,最适反应pH=7.4保持不变;在不加保护剂的条件下,4℃放置50 d后游离酶仅保持40%以上的酶活力,而固定化酶能保持80%以上的酶活力.该固定化乳酸氧化酶用于催化氧化DL-乳酸生产丙酮酸,3 h后丙酮酸产率可达75%,连续循环使用5次固定化酶活力仍保持85%.     

复合纤维素膜固定化胰蛋白酶反应器及其应用于蛋白质酶解

合成了甲基丙烯酸缩水甘油酯-纤维素复合膜,并以此膜为基质共价键合固定化胰蛋白酶,以N-苯甲酰-L-精氨酰乙酯(BAEE)为底物,应用高效液相色谱系统测定了酶固定化膜柱的催化反应特性。研究结果表明:温度、pH值、离子强度、有机溶剂及蛋白变性剂等都对固定化酶的活力有一定的影响。在最适条件下,固定化胰蛋白酶的活力为17800U/g干膜,蛋白载量为3.6mg/g(≈0.15μmol/g)干膜,活性回收率达到52%.固定化酶表现出较高的使用和储藏稳定性,在40℃下,水解BAEE底物24h活力无显着变化。固定化酶膜柱在4℃冷藏保存100d仍保存90%以上的水解活力。固定化酶反应器被应用于蛋白质酶解的肽谱实验。     

粘质沙雷氏菌脂肪酶的固定化及催化拆分反式3-(4’-甲氧苯基)缩水甘油酸甲酯

 对粘质沙雷氏菌脂肪酶进行了固定化研究,确定硅藻土和环氧树脂Eupergit C是较好的固定化载体. 固定化后酶的热稳定性、 pH稳定性及储存稳定性均明显提高. 以Eupergit C共价固定的脂肪酶,其操作稳定性比硅藻土吸附酶好,重复使用10批次后,剩余酶活力还有50%左右,戊二醛交联对Eupergit C固定化酶稳定性的提高没有明显效果,而硅藻土吸附酶经戊二醛交联后稳定性有所提高,经5批次反应后剩余酶活力还有50%. 使用交联后的硅藻土固定化酶(1 g, 200 U), 在两相搅拌反应器(工作体积200 ml, 甲苯∶水体积比=1)中对地尔硫卓手性前体(±)-反式3-(4’-甲氧苯基)缩水甘油酸甲酯((±)-MPGM)(有机相浓度为0.5 mol/L)进行了催化拆分,经5批次反应后,共得纯(2R,3S)-(-)-MPGM 18.6 g, 产品光学纯度(对映体过量)>99%, 总收率为37.2%.     

聚合马来松香乙二醇酯Ca(Ⅱ)、Ni(Ⅱ)配合物固定化淀粉酶研究

将松香改性合成聚合马来松香乙二醇酯(简称MEEP),使之分别与CaCl2、NiCl2、MgCl2和CuCl2反应,制备聚合马来松香乙二醇酯Ca(Ⅱ)、Ni(Ⅱ)、Mg(Ⅱ)和Cu(Ⅱ)配合物,再对淀粉酶进行固定化,比较了固定化酶和游离酶的性能.实验结果表明,4种聚合马来松香乙二醇酯配合物固定化酶使用5次后,固定化酶保留活力均在50%以上,其中MEEPCa(Ⅱ)和MEEPNi(Ⅱ)固定化酶的效果较好,固定化酶保留活力均在70%以上;固定化酶最适温度50℃,较游离酶高10℃;聚合马来松香乙二醇酯Ca(Ⅱ)、Ni(Ⅱ)固定化酶的最适pH值分别为5.24、6.86,米氏常数分别为1.47×10-4kg/L和2.64×10-4kg/L,游离酶为2.69×10-5kg/L.     

混合溶剂系统中固定化脂肪酶对酮基布洛芬的催化酯化反应

以硅藻土吸附的脂肪酶为催化剂,对外消旋酮基布洛芬[2-(3-苯甲酰苯基)丙酸]进行对映选择性酯化反应;考察了不同的脂肪酶制剂,固定化时所加缓冲液的体积与pH值,酰基受体(醇)的种类以及混合溶剂系统的组成等因素对酶活性的影响.结果表明,在所考察的7种脂肪酶中,以LipaseOF的酪化活性最高;用硅藻土吸附固定化酶时,缓冲溶液的最适pH为7.0左右,每克酶粉加1.0mL缓冲溶液为最佳;固定化酶催化酯化的活性比游离的脂肪酶高.在酮基布洛芬与不同酰基受体(醇)的酶促酯化反应中,以丙醇的反应速度为最快.在由一种主溶剂与一种助溶剂组成的混合溶剂系统中,酶促酯化的速度要比在单一的主溶剂或助溶剂系统中快.当以1gP值较大的环己烷或异辛烷等为主溶剂,甲苯为助溶剂时,脂肪酶催化酮基布洛芬酯化反应的活性最高.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.