On-line chemiluminescence detection for isoelectric focusing of heme proteins on microchips

In this paper we present a sensitive chemiluminescence (CL) detection of heme proteins coupled with microchip IEF. The detection principle was based on the catalytic effects of the heme proteins on the CL reaction of luminol-H2O2 enhanced by para-iodophenol. The glass microchip and poly(dimethylsiloxane) (PDMS)/glass microchip for IEF were fabricated using micromachining technology in the laboratory. The modes of CL detection were investigated and two microchips (glass, PDMS/glass) were compared. Certain proteins, such as cytochrome c, myoglobin, and horseradish peroxidase, were focused by use of Pharmalyte pH 3-10 as ampholytes. Hydroxypropylmethylcellulose was added to the sample solution in order to easily reduce protein interactions with the channel wall as well as the EOF. The focused proteins were transported by salt mobilization to the CL detection window. Cytochrome c, myoglobin, and horseradish peroxidase were well separated within 10 min on a glass chip and the detection limits (S/N=3) were 1.2x10(-7), 1.6x10(-7), and 1.0x10(-10) M, respectively.     

Analysis of a biopolymer by capillary electrophoresis with a chemiluminescence detector using a polymer solution as the separation medium.

We developed capillary electrophoresis with a chemiluminescence detector using a polymer solution as the separation medium for the analysis of biopolymers, such as DNA and protein. A peroxyoxalate chemiluminescence reagent of bis(2,4,6-trichlorophenyl)oxalate was used together with fluorescein-labeling reagent. When a migration buffer solution containing carboxylmethylcellulose was used, the flow-type chemiluminescence detection cell was found to give a better resolution than the batch-type one. Fluorescein-labeled adenosine triphosphate of 1.0 x 10(-4) M was examined by means of capillary electrophoresis with absorption (260 nm), fluorescence (ex. 496 nm and em. 517 nm), and chemiluminescence detectors. The chemiluminescence detection showed the highest sensitivity among them; the S/N ratios obtained by absorption, fluorescence, and chemiluminescence detections were 4, 38, and 130, respectively. Fluorescein-labeled DNA was prepared through a polymerase chain reaction using fluorescein-labeled deoxyadenosine triphosphate. A mixture of the labeled DNA fragments (500, 600, 700, 800, 900, and 993 bp) was successfully separated and detected by the present system. A mixture of proteins (lysozyme, cytochrome C, and ribonuclease A) which were labeled with fluorescein isothiocyanate was also separated and detected.     

Highly sensitive chemiluminescence detection of copper(II) in capillary electrophoresis with field-amplified sample injection

Field-amplified sample injection of copper(II) was investigated using capillary electrophoresis with chemiluminescence detection. The sensitivity of copper(II) has been improved markedly by the field-amplified sample injection technique and the detection limit reaches 2 x 10(-11) M. By injection of a short plug of water before sample introduction, the sensitivity can be further improved 5-fold and the detection limit reaches 4 x 10(-12) M. The relative standard deviations (n = 6) of the migration time and the peak height are 0.61% and 4.7% at 1.0 x 10(-9) M Cu(II), respectively. Parameters affecting the field-amplified sample injection, such as separation voltage and concentration of electrophoretic buffer, have been investigated.     

Miniaturization of batch- and flow-type chemiluminescence detectors in capillary electrophoresis

Glass and PTFE tubes as detection cells were put in small light-tight boxes to achieve miniaturization of batch-and flow-type chemiluminescence detectors for capillary electrophoresis. These light-tight boxes which included a detection cell and a photosensor module were successfully designed. In the batch-type detector using a glass tube as a detection cell, the influences of a repeated injection of sample and a reagent volume of the detection cell on chemiluminescence intensity were examined in detail. By using 3.8 mm I.D. glass tube including 400 microl chemiluminescence reagent solution, the chemiluminescence peaks were reproducibly observed for the repeated injection experiment up to the eight injection with each run time of 3.0 min. Dansyl-Trp was determined over the range 3 x 10(-8)-1 x 10(-5) M with the detection limit of 0.43 fmol (S/N=3). In the flow-type detector using a PTFE tube as a detection cell, both ends of the PTFE tube were connected to three-way joints; a chemiluminescence reagent solution was delivered into the cell and a capillary was inserted through one of the joints while an electrode was inserted through the other one. Dansyl-Trp was determined over the range 1 x 10(-7)-1 x 10(-5) M with the detection limit of 1.3 fmol (S/N=3). By using the compact flow-type detector, a mixture of dansyl-amino acids was separated and detected in micellar electrokinetic chromatography mode.     

Sensitive, label-free protein assay using 1-ethyl-3-methylimidazolium tetrafluoroborate-supported microchip electrophoresis with laser-induced fluorescence detection

Based on the dimer-monomer equilibrium movement of the fluorescent dye Pyronin Y (PY), a rapid, simple, highly sensitive, label-free method for protein detection was developed by microchip electrophoresis with LIF detection. PY formed a nonfluorescent dimer induced by the premicellar aggregation of an anionic surfactant, SDS, however, the fluorescence intensity of the system increased dramatically when proteins such as BSA, bovine hemoglobin, cytochrome c, and trypsin were added to the solution due to the transition of dimer to fluorescent monomer. Furthermore, 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF4) instead of PBS was applied as running buffers in microchip electrophoresis. Due to the excellent properties of EMImBF4, not only nonspecific protein adsorption was more efficiently suppressed, but also approximately ten-fold higher fluorescence intensity enhancement was obtained than that using PBS. Under the optimal conditions, detection limits for BSA, bovine hemoglobin, cytochrome c, and trypsin were 1.00x10(-6), 2x10(-6), 7x10(-7), and 5x10(-7) mg/mL, respectively. Thus, without covalent modification of the protein, a protein assay method with high sensitivity was achieved on microchips.     

Self-assembled multilayer of gold nanoparticles for amplified electrochemical detection of cytochrome c

Although different kinds of film materials and some modification techniques are applied for the development of protein-film electrochemistry, the design of a more ordered adsorption platform with improved sensitivity is still required. Here we employ single-strand DNA (ssDNA)-functionalized gold nanoparticles as scaffolds for the construction of a multilayered uniform self-assembled structure via the hybridization of complementary ssDNA. After adsorbing with native conformation onto the uniformly built electrode, cytochrome c responded very well in voltammetry experiments. The peak currents increase with the addition of the number of gold nanoparticle layers, which indicates that the multilayer gold nanoparticles not only provide a compatible microenvironment for the protein to undergo direct electron transfer reactions but also amplify the electrochemical signals by increasing the binding sites for the protein immobilization. Furthermore, ultra-sensitive detection of cytochrome c by using this multilayer gold nanoparticle-modified electrode is carried out. The linear range is from 2 x 10(-9) to 1 x 10(-7) M with a detection limit of 6.7 x 10(-10) M.     

Detection of clindamycin by capillary electrophoresis with an end-column electrochemiluminescence of tris(2,2'-bypyridine)ruthenium(II)

Coupled capillary electrophoresis (CE) with end-column electrogenerated chemiluminescence (ECL) was adopted for the quantitative detection of clindamycin. Clindamycin enhanced ECL intensity of tris(2,2'-bypyridine)ruthenium(II) (Ru(bpy)(3)(2+)) as a coreactant. Under the optimized conditions, the ECL intensity was linear with the concentration of clindamycin over the range from 5.0 x 10(-7) to 1.0 x 10(-4)M with a detection limit of 1.4 x 10(-7)M. The proposed CE-ECL was successfully applied for the detection of clindamycin in pharmaceutical and clinic samples. The interaction of clindamycin with hemoglobin was also investigated. The binding constant of clindamycin with hemoglobin was estimated to be 3.6 x 10(3)M(-1).     

Metalloprotein association,self-association,and dynamics governed by hydrophobic interactions: simultaneous occurrence of gated and true electron-transfer reactions between cytochrome f and cytochrome c(6) from Chlamydomonas reinhardtii

Noninvasive reconstitution of the heme in cytochrome c(6) with zinc(II) ions allowed us to study the photoinduced electron-transfer reaction (3)Zncyt c(6) + cyt f(III) --> Zncyt c(6)(+) + cyt f(II) between physiological partners cytochrome c(6) and cytochrome f, both from Chlamydomonas reinhardtii. The reaction kinetics was analyzed in terms of protein docking and electron transfer. In contrast to various protein pairs studied before, both the unimolecular and the bimolecular reactions of this oxidative quenching take place at all ionic strengths from 2.5 through 700 mM. The respective intracomplex rate constants are k(uni) (1.2 +/- 0.1) x 10(4) s(-1) for persistent and k(bi) (9 +/- 4) x 10(2) s(-1) for the transient protein complex. The former reaction seems to be true electron transfer, and the latter seems to be electron transfer gated by a structural rearrangement. Remarkably, these reactions occur simultaneously, and both rate constants are invariant with ionic strength. The association constant K(a) for zinc cytochrome c(6) and cytochrome f(III) remains (5 +/- 3) x 10(5) M(-1) in the ionic strength range from 700 to 10 mM and then rises slightly to (7 +/- 2) x 10(6) M(-1), as ionic strength is lowered to 2.5 mM. Evidently, docking of these proteins from C. reinhardtii is due to hydrophobic interaction, slightly augmented by weak electrostatic attraction. Kinetics, chromatography, and cross-linking consistently show that cytochrome f self-dimerizes at ionic strengths of 200 mM and higher. Cytochrome f(III) quenches triplet state (3)Zncyt c(6), but its dimer does not. Formation of this unreactive dimer is an important step in the mechanism of electron transfer. Not only association between the reacting proteins, but also their self-association, should be considered when analyzing reaction mechanisms.     

Development of FIA equipped with a chemiluminescence detector using a mixed reagent of luminol and 1,10-phenanthroline.

We developed an FIA system equipped with a chemiluminescence detector using a mixed chemiluminescence reagent of luminol and 1,10-phenanthroline for the detection of metal ions and metal complexes. The carrier, mixed chemiluminescence reagent comprising luminol, 1,10-phenanthroline, and cethyltrimethylammonium bromide, and H2O2 solutions were fed by corresponding pumps at a definite flow rate. Sample solutions dissolving hematin, [Co(NH3)4(H2O)2]2(SO4)3, CuSO4, NiCl2, K3[Fe(CN)6], and K4[Fe(CN)6] were analyzed as models by the means of the present FIA system. Solutions of hematin, [Co(NH3)4(H2O)2]2(SO4)3, CuSO4, and NiCl2 were detected as positive peaks, as usual. The order of the catalytic activity of these samples for the present chemiluminescence reaction using the mixed chemiluminescence reagent was [Co(NH3)4(H2O)2]2(SO4)3 > hematin > CuSO4 > NiCl2. On the other hand, sample solutions of K3[Fe(CN)6] and K4[Fe(CN)6] were detected as negative peaks and were determined over the ranges of 1 x 10(-8) - 1 x 10(-6) M with a detection limit of 1 x 10(-8) M and 2 x 10(-8) - 4 x 10(-6) M with a detection limit of 2 x 10(-8) M, respectively. Their negative peaks were observed reproducibly with a relative standard deviation of 2 - 5%.     

Direct electrochemical behavior of cytochrome c on DNA-modified glassy carbon electrode and its application to cytochrome c biosensor.

DNA was immobilized on glassy carbon electrodes to fabricate DNA-modified electrodes. The direct electron transfer of horse heart cytochrome c on DNA-modified glassy carbon electrode was achieved. A pair of well-defined redox peaks of cytochrome c appeared at Epc = -0.017 V and Epa = 0.009 V (vs. Ag/AgCl) in 10 mM phosphate buffer solution (pH 7.0) at a scan rate of 50 mV/s. The electron transfer coefficient (alpha) and the standard rate constant of the surface reaction (Ks) of cytochrome c on DNA-modified electrodes could be estimated to be 0.87 and 34.52 s(-1), respectively. The DNA-modified glassy carbon electrode could be applied to detect cytochrome c by means of differential pulse voltammetry (DPV). The cathodic peak current was proportional to the quantity of cytochrome c in the range of 4.0 x 10(-6) M to 1.2 x 10(-5) M. The correlation coefficient is 0.996, and with the detection limit was 1.0 x 10(-6) M (three times the ratio of signal to noise, S/N = 3).     

On-capillary chemiluminescence detection for capillary electrophoresis with a single capillary.

On-capillary chemiluminescence detection for capillary electrophoresis with a single capillary was reported. A hole (about 30 microm diameter) was made on the capillary wall at about 50.5 cm from the inlet end. Hydrogen peroxide solution could enter the capillary from the hole, and mixed with luminol and copper(II) to produce chemiluminescence. The chemiluminescence was detected by a PMT under the hole. Several factors that influenced chemiluminescence intensity were investigated. The detection limits for luminol and N-(4-aminolbutyl)-N-ethylisoluminol (ABEI) were 1 x 10(-11) and 2 x 10(-10) mol L(-1), respectively. The method features simple construction and no dead volume.     

Bonded dimethylacrylamide as a permanent coating for capillary electrophoresis

A method for coating capillaries for capillary electrophoresis with chemically bonded polydimethylacrylamide has been developed, and the properties of the capillaries have been evaluated. The coated capillaries provided high separation efficiency, 12 x 10(5) theoretical plates/m was obtained for cytochrome c. The electroosmotic flow at pH 8.0 was 10 x 10(-10) to 6 x 10(-10) m2 V(-1) s(-1). The coated capillaries were quite stable at high pH. At least 150 runs could be done at pH 10 without appreciable performance deterioration. The excellent performance of the coated capillaries was illustrated by separation of basic proteins, acidic proteins, 9-fluorenylmethyl chloroformate-derivatized neurotransmitter amino acids, peptide reference mixtures and peptides digested from a bacteria protein.     

Determination of arsenate by sorption pre-concentration on polystyrene beads packed in a microfluidic device with chemiluminescence detection

A highly sensitive chemiluminescence (CL) method for the determination of arsenate in water based on a simple microfluidic device was developed. The method was based on sorption pre-concentration of arsenate as a form of vanadomolybdoarsenate heteropoly acid (VMoAs-HPA) ion-paired with hexadecyltrimethylammonium bromide on the surface of polystyrene beads packed in a microfluidic device monitored by chemiluminescence detection. The composition of the VMoAs-HPA complex was studied by varying the concentrations of ammonium molybdate, ammonium vanadate and sulfuric acid with a variable-size simplex optimization process, of which the optimum concentrations were 6.3 x 10(-5), 5.0 x 10(-6) and 1.0 x 10(-2) M, respectively. In this work, 1.0 x 10(-3) M ethylenediaminetetraacetic acid was added to all work solutions to remove the interferences of the other metal ions on the CL detection. The integration of sorption pre-concentration not only increased the detection sensitivity but also eliminated the interference from phosphate and chromate. The calibration plot was linear from 1.0 x 10(-7) to 5.0 x 10(-5) M As(v). The limit of detection was 8.9 x 10(-8) M As(v) (S/N = 3). The time required for one analysis run was as short as 5 min. The relative standard deviation was 5.9% (n = 9). This method was successfully applied to the determination of arsenate in mineral-, drinking- and tap-water samples.     

An electrochemical biosensor for nitric oxide based on silver nanoparticles and hemoglobin.

A nitric oxide (NO) biosensor based on silver nanoparticles was fabricated with high sensitivity and selectivity as well as stability. Silver nanoparticles could preserve the microstructures of hemoglobin, but the electrochemical reactivity of the protein and its detection sensitivity toward NO could be greatly enhanced. Accordingly, a NO biosensor was developed. The linear concentration range was from 1.0 x 10(-6) to 5.0 x 10(-5) M. Its detection limit was 3.0 x 10(-7) M with a sensitivity of 0.0424 microA microM(-1) NO. The possible co-existing compounds would not interfere with the detection.     

A simple and rapid flow injection chemiluminescence determination of cysteine with Ru(phen)3(2+)-Ce(IV) system

A new chemiluminescence system was developed for the determination of cysteine by flow injection system. This method is based on the reaction of L-cysteine with Ru(phen)3(2+) and Ce(IV) to produce chemiluminescence. The calibration curve was linear over the range 8.0x10(-7) to 4.0x10(-5) and 4.0x10(-5) to 1.0x10(-3) M with a detection limit of 7.0x10(-7) M (S/N=3). The relative standard deviation of 4.0x10(-6) M cysteine was found 3.5% (n=10). The influence of potential interfering substances was studied. The proposed method was successfully applied for the flow injection determination of cysteine in the real samples with minimum sampling rate of 90 sample/h.     

Separation of biogenic amines by micellar electrokinetic chromatography with on-line chemiluminescence detection

A method of on-line chemiluminescence detection with capillary electrophoresis for biogenic amines (diaminopropane, putrescine, cadaverine and diaminohexane) labeled with N-(4-aminobutyl)-N-ethylisoluminol is reported for the first time. Two separation modes, capillary zone electrophoresis and micellar electrokinetic chromatography (MEKC), were studied. The results show that excellent resolution was achieved in MEKC. Parameters affecting separation process and chemiluminescence detection have been examined in detail. Under the optimum conditions, the baseline separation of four amines was obtained within 7.5 min. The detection limits (S/N=3) of diaminopropane, putrescine, cadaverine and diaminohexane are 3.5 x 10(-8), 3.5 x 10(-8), 3.9 x 10(-8) and 1.2 x 10(-7) M, respectively. The method was applied to the analysis of biogenic amines in lake water.     

Microchip capillary electrophoresis using on-line chemiluminescence detection

Chemiluminescence detection was used in capillary electrophoresis integrated on a microchip. Quartz microchips have two main channels and four reservoirs. Dansyl-lysine and -glycine were separated and detected with bis[(2-(3,6,9-trioxadecanyloxycarbony)-4-nitrophenyl]oxalate as peroxyoxalate chemiluminescent reagent. These dansyl amino acids came into contact with the chemiluminescence reagent to produce visible light at the interface between the separation channel and chemiluminescence reagent-containing reservoir. The detection limit (S/N = 3) for dansyl-lysine was 1 x 10(-5) M, which corresponded to the very small mass detection limit of ca. 0.4 fmol. However, the concentration sensitivity in the present system was approximately two orders of magnitude lower than that in the conventional capillary electrophoresis-chemiluminescence detection system. The relative standard deviations of migration time and peak height for dansyl-lysine were 4.2 and 4.5%, respectively. A channel conditioning before every run and an appropriate control of voltages were needed for the reproducible results. The present system had advantages in rapid separation time (within 40 s), small (several 10 pI) and accurate sample injection method using a cross-shaped injector, and simplification and miniaturization of the detection device.     

Design and evaluation of capillary electrophoresis in dynamically coated capillaries coupled with chemiluminescence detection

A dynamic coating capillary electrophoresis coupled with a simplified on-line chemiluminescence detection system was designed and evaluated. In the proposed system, poly-vinylpyrrolidone was used as dynamic coating substance in the separation buffer to reduce the unwanted protein non-specific adsorption, which was first applied in capillary electrophoresis coupling with on-line chemiluminescence detection. In order to avoid complex processing, an ordinary plastic cuvette was modified as a three-way joint. The chemiluminescence reaction conditions and capillary electrophoresis separation conditions were investigated in detail. The results showed that the coated capillary can be injected protein samples at least 30 times continuously with good repeatability. Under optimal conditions, the chemiluminescence relative intensity was linear with the concentration of hemoglobin in the range of 4-1850 μg mL(-1) and the detection limit was 2.0 μg mL(-1) (S/N=3). The relative standard deviation of migration times and peak heights for 40 μg mL(-1) hemoglobin were 2.5% and 4.1% (n=11) respectively. Interference of matrix effects was overcome by the calibration according to standard addition methods. Afterwards, the method was validated successfully and was applied to detect the concentration of hemoglobin in the serum of haemolytic patients.     

A facile and sensitive chemiluminescence detection of amino acids in biological samples after capillary electrophoretic separation

It was found that native amino acids enhanced the chemiluminescence (CL) reaction between luminol and BrO(-) in an alkaline aqueous solution. This has led to the development of a facile and highly sensitive CL detection scheme for the determination of amino acids in biological samples after capillary electrophoretic (CE) separation. The CE-CL conditions were optimized. An electrophoretic buffer of 2.5 x 10(-2) M sodium borate (pH 9.4) containing 1 x 10(-4) M luminol was used. The oxidizer solution of 8 x 10(-4) M NaBrO in 0.1 M sodium carbonate buffer solution (pH 12.5) was introduced post-column. Under the optimal conditions, the detection limits were 1.0 x 10(-7) M for glutamic acid (Glu) and 1.3 x 10(-7) M (S/N = 3) for aspartic acid (Asp). The relative standard deviations (RSDs) of peak area and migration time were in the ranges of 3.8-4.3% and 1.4-1.6%, respectively. The present method was applied to the determination of excitatory amino acids (i.e., Asp and Glu) in rat brain tissue and monkey plasma. The levels of these major excitatory amino acids in monkey plasma were quantified for the first time and found to be 1.17 +/- 0.17 x 10(-5) M (mean +/- SD, n = 6) for Glu and 1.64 +/- 0.19 x 10(-6) M for Asp, which were comparable with the levels in human plasma.     

Extension of separation range in capillary isoelectric focusing for resolving highly basic biomolecules

The non-availability of commercial carrier ampholytes in the pH range greater than 11 has contributed to difficulties in focusing and resolving highly basic proteins/peptides using capillary isoelectric focusing (cIEF). Two different approaches, involving the use of N,N,N',N'-tetramethylethylenediamine (TEMED) and ampholyte 9-11, are investigated for their effects on the extension of separation range in cIEF. The addition of TEMED into pharmalyte 3-10 not only prevents the peptides/proteins from focusing in sections of the capillary beyond the detection point, but also extends the separation range to at least isoelectric point (pI) 12. The combination of ampholyte 9-11 with pharmalyte 3-10 surprisingly provides baseline resolution between bradykinin (pI 12) and cytochrome c (pI 10.3). The sample mixture, containing bradykinin, the high-pI protein calibration kit (pI 5.2-10.3), and cytochrome c digest, is employed to demonstrate the cIEF separation of proteins and peptides over a wide pH range of 3.7-12.