快速分离柱高效液相色谱法测定卷烟主流烟气中的主要羰基化合物

选择2,4-二硝基苯肼(DNPH)为羰基化合物的衍生化试剂,建立了快速分离柱高效液相色谱测定卷烟主流烟气中8种羰基化合物的方法。采用经2,4-二硝基苯肼酸性溶液处理过的剑桥滤片捕集烟气,再用含2%（体积分数）吡啶的乙腈溶液进行萃取,以ZORBAX Stable Bound色谱柱(50 mm×4.6 mm,1.8 μm)进行快速分离,最后由二极管阵列检测器于365 nm下进行检测。该方法的回收率为89.1%～99.2%,相对标准偏差（RSD)在6.0%以下。该方法分析时间短,流动相消耗少,且操作简便、重复性好、回收率高。     

气相色谱法测定食品包装材料中微量甲醛

建立了食品包装材料中微量甲醛的气相色谱检测方法.样品浸泡液经2,4-二硝基苯肼(DNPH)衍生,正己烷萃取衍生反应物后,气相色谱-电子捕获检测器法测定.采用乙腈多次重结晶法提纯衍生剂(DNPH),以降低DNPH中含有的甲醛衍生产物,避免影响测定;探讨了衍生化反应的条件以及色谱条件.甲醛的残留在0.05～50 mg/L的范围内线性关系良好,检出限为0.05 mg/kg,相对标准偏差为2.7%～5.0%,回收率范围在88.6%～98.0%之间.     

丹磺酰肼衍生-高效液相色谱-荧光检测法测定包装纸中的甲醛和乙醛

建立了丹磺酰肼(DNSH)衍生-高效液相色谱-荧光检测测定包装纸中甲醛和乙醛的分析方法,并与2,4-二硝基苯肼(DNPH)衍生法进行了比较。纸张样品经衍生化试剂振荡萃取30 min,衍生化反应24 h,萃取液经PSA/C18净化管净化处理后,以Diamonsil~ C18(2)色谱柱(150 mm×4.6 mm,5μm)为固定相,用醋酸水溶液(pH2.55)-乙腈为流动相进行梯度洗脱。采用荧光检测器检测,激发波长为330 nm,发射波长为484 nm。结果表明,衍生剂、甲醛-DNSH和乙醛-DNSH在20 min内可完全分离,方法的加标回收率为81.64%~106.78%,相对标准偏差(RSD)为2.02%~5.53%(n=5),甲醛和乙醛的检出限分别为19.2μg/kg和20.7μg/kg,定量限分别为63.9μg/kg和69.1μg/kg。该法操作简单,灵敏度高,比常规方法具有更低的检出限,能很好地应用到实际样品检测中,为低含量醛类化合物的检测提供了一种新思路。     

直接衍生离子液体富集高效液相色谱分析水基胶中脂肪族醛酮

建立了以2,4-二硝基苯肼(DNPH)直接衍生,1-丁基-3-甲基咪唑六氟磷酸盐(［BMIM］PF6)萃取富集,高效液相色谱(HPLC)分析水基胶中痕量脂肪族醛酮的方法。分散的水基胶乳液用80 mg/L DNPH衍生化试剂(含0.44 mol/L磷酸)于40 ℃衍生18 min。取离心后的上层衍生液,加入0.5 mL ［BMIM］PF6于30 ℃萃取富集,离子液体相过滤后进行HPLC分析。采用Dionex Acclaim Explosives E2色谱柱(250 mm×4.6 mm, 5 μm),以水-乙腈为流动相在流速1.2 mL/min进行梯度洗脱,色谱柱温度为35 ℃,检测波长为365 nm。结果表明,8种脂肪族醛酮的检出限为0.022～0.221 mg/kg,定量限为0.073～0.738 mg/kg,相对标准偏差为3.5%～7.3%,回收率为84.0%～102.5%。与溶剂萃取法相比,该法具有检出限和定量限低、稳定性高、测定更准确的优势。     

柱前衍生高效液相色谱法测定血清中克拉霉素的含量

建立了2,4-二硝基苯肼柱前衍生反相高效液相色谱紫外检测法测定血清中克拉霉素的含量,将在碱性条件下甲基叔丁基醚的血清萃取物,与2,4-二硝基苯肼在55℃酸性条件下反应30 min,然后用乙腈-0.05 mol/L pH 7.2磷酸盐缓冲液(4852)在Alltima C18色谱柱上进行分离,在340 nm检测衍生物.方法的线性范围为0.05～3.2 mg/L(r=0.9993);检出限为30 μg/L,绝对回收率大于89%,相对标准差小于10%.本方法已用于克拉霉素在健康受试者中的药代动力学研究.     

柱前衍生-萃取阻断反应-高效液相色谱法测定化妆品中游离甲醛

建立了柱前衍生化-萃取阻断反应-高效液相色谱(HPLC)测定化妆品中甲醛的方法。化妆品中甲醛检测的难点是: 甲醛缓释剂类防腐剂在衍生过程中释放甲醛,影响游离甲醛的准确测定。以2,4-二硝基苯肼(DNPH)乙腈溶液-磷酸盐缓冲液(pH 2)(1:1, v/v)为提取溶液,于室温下快速衍生2 min后,立即加入二氯甲烷萃取,阻断衍生反应,经乙腈稀释后进行HPLC测定。以Agilent C18柱(250 mm×4.6 mm, 5 μm)为分离柱,乙腈-水(60:40, v/v)为流动相,流速为1.0 mL/min,于355 nm波长下检测。在洗发水、乳液、膏霜、洗手液、牙膏、指甲油、粉饼中分别添加50、100、500、1000 μg/g 4个浓度水平的甲醛,其回收率为81%～106%,相对标准偏差(n=6)＜5.0%。方法的定量限(以信噪比(S/N)＞10计)为50 μg/g。该方法快速、简便、重现性好,且可以有效避免甲醛缓释剂类防腐剂分解释放甲醛,适用于化妆品中游离甲醛的测定。     

超高效液相色谱法测定餐饮油烟中的十五种醛酮

采用在流动相中添加四氢呋喃的方法来改善丙烯醛-2,4-二硝基苯肼(DNPH)和丙酮-DNPH的分离,然后优化流动相比例和梯度,确定了UPLC分析醛酮-DNPH的色谱条件。有机溶剂消耗量和分析时间分别是传统方法的1/20~1/10和12%~30%;工作曲线线性相关系数、方法检出限和测定下限均满足HJ683-2014的规定;UPLC法测定醛酮的2,4-二硝基苯肼衍生物的平均回收率为91.5%~101%。基于常规的超高效反向C18色谱柱,在40℃条件下建立了高效分离醛酮混标的UPLC方法,方法已用于测定餐饮油烟中醛酮类化合物。     

在线衍生–高效液相色谱法测定食品中的甲醛次硫酸氢钠

建立在线衍生–高效液相色谱法测定食品中的甲醛次硫酸氢钠。食品中的甲醛次硫酸氢钠用碘酸钾溶液氧化后释放出甲醛并被水提取,以2,4-二硝基苯肼(DNPH)的乙腈–乙酸溶液为衍生液,在线衍生2 min,衍生物在Agilent C_(18)色谱柱上分离,以乙腈–水(65∶35)溶液为流动相进行洗脱,用二极管阵列检测器测定,检测波长为350 nm。试验结果表明,在0.1～5.0 mg/L范围内,甲醛的质量浓度与色谱峰面积呈良好的线性关系(r~2=0.999),方法检出限为0.4 mg/kg,样品的加标回收率为89.84%～97.46%,测定结果的相对标准偏差为0.25%～0.43%(n=6)。该方法操作简单快捷,分离效果好,适用于食品中甲醛次硫酸氢钠的日常分析测试。     

在线衍生-高效液相色谱法测定化妆品中的游离甲醛

采用自动在线衍生-高效液相色谱法测定化妆品中游离甲醛的含量。样品经乙腈涡旋提取,以2,4-二硝基苯肼的乙腈-乙酸溶液为衍生液,在线衍生2min后,衍生物在Agilent C_(18)色谱柱上分离,以乙腈(65+35)溶液为流动相进行洗脱,用二极管阵列检测器测定,检测波长为355nm。甲醛线性范围为1.0~20.0mg·L~(-1),测定下限(10S/N)为50mg·kg~(-1)。加标回收率在83.0%~98.4%之间,测定值的相对标准偏差(n=6)在3.4%~7.8%之间。     

衍生液提取-高效液相色谱法测定食品中甲醛

提出了高效液相色谱法测定了几种食品中甲醛含量。以衍生液2,4-二硝基苯肼乙腈溶液-pH 5的磷酸盐缓冲溶液(1+1)的混合溶液为提取剂对样品进行提取,以Agilent C18色谱柱(4.6 mm×250 mm,5μm)为固定相,以甲醇-水(70+30)溶液为流动相分离。甲醛的测定下限(10S/N)为5.0 mg.kg-1。以鲜香菇、鲜鱿鱼、奶粉和面粉样品为基体,分别添加5.0,10.0,20.0 mg.kg-1甲醛标准溶液,回收率在73.3%~97.7%之间,相对标准偏差(n=6)在1.4%~5.0%之间。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.