Effect of the Dopant Nature on the Response of Sensor Arrays Based on Polypyrrole

The effect of the nature of the dopant on the response of a sensor array based on films of polypyrrole under the influence of the vapor of various organic solvents was studied. It was found the electric conductivity of the polymer can both increase and decrease during the action of analytes on electropolymerized films of polypyrrole. It is suggested that the main factors determining the response of polypyrrole are the morphology of the films and the type of charge carriers in the polymer, which depend on the nature of the dopant anion, and also the polarity and nucleophilicity/electrophilicity of the analyte. The responses of polypyrrole and polyaniline are compared, and the effect of the nature of the conducting polymer on them is analyzed. __________ Translated from Teoreticheskaya i Eksperimental'naya Khimiya, Vol. 41, No. 5, pp. 265–271, September–October, 2005.     

Electrochemical measurements of the ion conductivity, permselectivity and transference numbers of polypyrrole and polypyrrole derivatives

Electrochemical dc and ac measurements were carried out on free-standing polypyrrole (ppy) membranes to study the ion conductivity and permselectivity of the polymer as a function of the oxidation state. The membranes were prepared by electropolymerisation and mounted in a two-compartment cell, where the oxidation state of the ppy membrane could be adjusted by potentiostatic polarisation and the ion conductivity and permselectivity of the polymer could be measured in a symmetrical electrolyte/membrane/electrolyte configuration. Combining constant current permeation experiments with solution analysis using ion chromatography (IC) and atomic absorption spectroscopy (AAS), it was demonstrated that ppy exhibits not only an appreciable ion conductivity but also a distinct permeability and selectivity for anions in the oxidised state. Incorporation of immobile anions like dodecylsulfate or copolymerization with a modified pyrrole monomer like N-sulfopropyl-pyrrole carrying a sulfonate group leads to modified membranes which exhibit distinct cation permselectivity in the reduced state. Such a membrane can be switched dynamically between anion and cation permeability through electrochemical oxidation and reduction of the polymer backbone. Received: 27 March 1997 / Accepted: 18 July 1997     

Spectroelectrochemistry of conducting polypyrrole and poly(pyrrole–cyclodextrin) prepared in aqueous and nonaqueous solvents

Conducting polypyrrole (PPy) and poly(pyrrole-2,6-dimethyl-β-cyclodextrin) [poly(Py-β-DMCD)] films were prepared by electrode potential cycling on a gold electrode in aqueous and nonaqueous (acetonitrile) electrolyte solutions containing lithium perchlorate. The resulting products were characterized with cyclic voltammetry, in situ UV–Vis spectroscopy, and in situ conductivity measurements. For the electrosynthesis of poly(Py-β-DMCD), a (1:1) (mole–mole) (Py-β-DMCD) supramolecular cyclodextrin complex of pyrrole previously characterized with proton NMR spectroscopy was used as starting material. A different cyclic voltammetric behavior was observed for pyrrole and the poly(Py-β-DMCD) complex in aqueous and nonaqueous solutions during electrosynthesis. The results show that in both solutions in the presence of cyclodextrin, the oxidation potential of pyrrole monomers increases. However, the difference of oxidation potentials for films prepared in aqueous solution is larger than for the films prepared in nonaqueous solution. In situ conductivity measurements of the films show that films prepared in acetonitrile solution are more conductive than those synthesized in aqueous solutions. Maximum conductivity can be observed for PPy and poly(Py-β-DMCD) films prepared in nonaqueous solution in the range of 0.10 < E _Ag/AgCl < 0.90 V and 0.30 < E _Ag/AgCl < 0.90 V, respectively. In situ UV–Vis spectroelectrochemical data for both films prepared potentiodynamically by cycling the potentials from −0.40 < E _Ag/AgCl < 0.90 V in nonaqueous solutions are reported. This paper is dedicated to Prof. Alan Bond on the occasion of his 65th birthday in recognition of his numerous contributions toward electrochemistry.     

Electrochemical polymerization of imidazolum‐ionic liquids bearing a pyrrole moiety

A series of imidazolium‐based ionic liquid monomers bearing a terminal pyrrole moiety were synthesized and electrochemically polymerized. It is found that the polymerizability of the synthesized ionic liquids is strongly dependent on the type of the counteranions. Although bromide monomer is not polymerizable, well‐defined polymeric films can be formed on various substrates in the cases of flour‐containing anions (BF₄^?, PF₆^?). The performed characterizations show that all resulting polypyrrole films are electroactive, and the imidazolium‐based ionic liquid moieties are correctly incorporated in polymer films during the electropolymerization process. This work not only provides a facile new method to immobilize ionic liquids on solid surface. Interestingly, without use of any template unique “knit” morphology and nanostructure, even hierarchical structures could also be produced by the electropolymerization of these new functionalized pyrrole monomers. We found that the properties of the pendant ionic liquid units on the surface of the formed polymer films preserved, and by simple anion exchange their surface energy and tension could be easily tuned without loss of the electrical, optical properties, and morphology of the polypyrrole films. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4151–4161, 2008     

Low-voltage anodized TiO<Subscript>2</Subscript> nanostructures studied by alternate current electrochemical microscopy and photoelectrochemical measurements

This paper presents the characterization of TiO₂ nanostructures obtained by low-voltage anodization using alternate current electrochemical microscopy (AC-SECM) and photoelectrochemical (PEC) measurements. TiO₂ nanostructures were obtained from the exposure of titanium foils to several aqueous acidic solutions of hydrofluoric acid + phosphoric acid at potentials of 1 to 3 V. Scanning electron microscopy, X ray diffraction, and atomic force microscopy studies evidence the formation of a thin porous amorphous layer (<600 nm) with pore size in the range of 200–1,000 nm. By AC-SECM studies at different bias, we were able to confirm the unambiguous semiconducting properties of as-obtained porous titania films, as well as differences in surface roughness and conductivity in specimens obtained at both potentials. The difference in conductivity persists in air annealed samples, as demonstrated by electrochemical impedance spectroscopy and PEC measurements. Specimens obtained at 3 V show lower photocurrent and dark current than those obtained at 1 V, regardless of their larger conductivity, and we proposed it is due to differences on the oxide layer formed at the pore bottom.     

Impedance studies on the 5-V cathode material,LiCoPO<Subscript>4</Subscript>

Olivine-structured LiCoPO₄ is synthesized by a Pechini-type polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld-refined X-ray diffraction, scanning electron microscopy, Brunauer, Emmett, and Teller surface area technique, infrared spectroscopy, and Raman spectroscopy techniques, respectively. The ionic conductivity (σ ionic), dielectric, and electric modulus properties of LiCoPO₄ are investigated on sintered pellets by impedance spectroscopy in the temperature range, 27–50 °C. The σ (ionic) values at 27 and 50 °C are 8.8 × 10⁻⁸ and 49 × 10⁻⁸ S cm⁻¹, respectively with an energy of activation (E _a) = 0.43 eV. The electric modulus studies suggest the presence of non-Debye type of relaxation. Preliminary charge–discharge cycling data are presented.     

The network gel polymer electrolyte based on poly(acrylate-co-imide) and its transport properties in lithium ion batteries

Poly (acrylate-co-imide)-based gel polymer electrolytes are synthesized by in situ free radical polymerization. Infrared spectroscopy confirms the complete polymerization of gel polymer electrolytes. The ionic conductivity of gel polymer electrolytes are measured as a function of different repeating EO units of polyacrylates. An optimal ionic conductivity of the poly (PEGMEMA₁₁₀₀-BMI) gel polymer electrolyte is determined to be 4.8 × 10^–3 S/cm at 25 °C. The lithium transference number is found to be 0.29. The cyclic voltammogram shows that the wide electrochemical stability window of the gel polymer electrolyte varies from −0.5 to 4.20 V (vs. Li/Li⁺). Furthermore, we found the transport properties of novel gel polymer electrolytes are dependent on the EO design and are also related to the rate capability and the cycling ability of lithium polymer batteries. The relationship between polymer electrolyte design, lithium transport properties and battery performance are investigated in this research.     

Electrical and electrochemical studies on magnesium ion-based polymer gel electrolytes

The development of polymer gel electrolyte system with high ionic conductivity is the main objective of polymer research. Electrochemical devices based on lithium ion-conducting polymer electrolyte are not safe due to the explosive nature of lithium. An attempt has been made to synthesize magnesium ion-conducting polymeric gel electrolytes, poly (vinylidene fluoride-co-hexafluoropropylene)–propylene carbonate–magnesium perchlorate, PVdF(HFP)-PC–Mg(ClO₄)₂ using standard solution-cast techniques. The maximum room temperature ionic conductivity of the synthesized electrolyte system has been observed to be 5.0 × 10⁻³ S cm⁻¹, which is quite acceptable from a device fabrication point of view. The temperature-dependent conductivity and the dielectric behavior were also analyzed. The pattern of the temperature-dependent conductivity shows the Arrhenius behavior. The dielectric constant ε _r and dielectric loss ε _i increases with temperature in the low-frequency region but almost negligible in the high-frequency region. This behavior can be explained on the basis of electrode polarization effects. The real part M _r and imaginary part M _i versus frequency indicate that the systems are predominantly ionic conductors. Further, the synthesized electrolyte materials have been checked for its suitability in energy storage devices namely redox supercapacitor with conducting polymer polypyrrole as electrode materials, and finally, it was observed that it shows good capacitive behavior in low-frequency region. Preliminary studies show that the overall capacitance of 22 mF cm⁻² which is equivalent to a single electrode specific capacitance of 117 F gm⁻¹ was observed for the above said supercapacitors.     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Magnesium ion-conducting gel polymer electrolytes dispersed with fumed silica for rechargeable magnesium battery application

Effect of fumed silica dispersion on poly(vinylidene fluoride-co-hexafluoropropylene)-based magnesium ion-conducting gel polymer electrolyte has been studied using various physical and electrochemical techniques. The composite gel electrolytes are free-standing and flexible films with enough mechanical strength. The optimized composition with 3 wt.% filler offers a maximum ionic conductivity of ∼1.1 × 10⁻² S cm⁻¹ at ∼25 °C with good thermal and electrochemical stabilities. The Mg²⁺ ion conduction in the gel nanocomposite film is confirmed from the cyclic voltammetry, impedance spectroscopy, and transport number measurements. The space-charge layers formed between filler particles and gel electrolyte are responsible for the enhancement in ionic conductivity. The applicability of the gel nanocomposite to a rechargeable battery is examined by fabricating a prototype cell consisting of Mg [or Mg-multiwalled carbon nanotube (MWCNT) composite] and MoO₃ as negative and positive electrodes, respectively. The discharge capacity and the rechargeability of the cell have been improved when Mg metal is substituted by Mg-MWCNT composite. The discharge capacity of the optimized cell has found to be ∼175 mAh g⁻¹ of MoO₃ for an initial ten charge–discharge cycles.     

Chemical deposition and characterization of thin polypyrrole films on glass plates: role of organosilane treatment

 Thin chloride-doped polypyrrole films (PPyCl) were deposited chemically onto untreated and silane-treated planar glass plates from aqueous solutions. The organosilanes used to treat the glass substrates were methyltriethoxysilane (Cl), propyltrimethoxysilane (C3), octyltrimethoxysilane (C8) and aminopropyltriethoxysilane (APS). The decreasing order of hydrophobic character of silane-treated glass slides, as measured by water contact angle measurements, was glass–APS ≅ glass–C8 > glass–C3 > glass–C1 > glass. X-ray photoelectron spectroscopy was used to determine the surface chemical composition of the glass plates before and following coating with the silane coupling agents and/or the PPy thin layer, respectively. The attenuation in intensity of the glass Na_{1 s} peak enabled the average thickness of the various organosilane overlayers to be estimated. Atomic force microscopy showed that the morphology of the organosilane overlayers was islandlike. The domains have a structure which depends upon the nature of the organosilane in question. Scanning electron microscope images showed that the morphology of the PPyCl thin films was homogeneous when coated onto glass–APS and glass–C8, but wrinkled at the surface of glass, glass–C1 and glass–C3 plates. Qualitative peel tests using 3M adhesive tape showed very good adhesion of PPyCl to the glass–APS substrate, whereas adhesion was fairly poor in the case of glass–PPy and PPy–alkylsilane–glass interfaces. The results of this multitechnique study suggest that hydrophobic interactions are important to obtain homogeneous and continuous thin PPy films, but Lewis acid–base interactions are the driving forces for strong and durable PPy–glass adhesion. Received: 3 January 2000/Accepted: 19 May 2000     

Electrochemistry and electrocatalytic activity of polypyrrole/ferrocyanide films on a glassy carbon electrode

Functionalized polypyrrole films were prepared by incorporation of Fe(CN)₆ ³⁻ as doping anion during the electropolymerization of pyrrole at a glassy carbon electrode from aqueous solution. The electrochemical behavior of the Fe(CN)₆ ³⁻/Fe(CN)₆ ⁴⁻ redox couple in polypyrrole was studied by cyclic voltammetry. An obvious surface redox reaction was observed and dependence of this reaction on the solution pH was illustrated. The electrocatalytic ability of polypyrrole film with ferrocyanide incorporated was demonstrated by oxidation of ascorbic acid at the optimized pH of 4 in a glycine buffer. The catalytic effect for mediated oxidation of ascorbic acid was 300 mV and the bimolecular rate constant determined for surface coverage of 4.5 × 10⁻⁸ M cm⁻² using rotating disk electrode voltammetry was 86 M⁻¹ s⁻¹. Furthermore, the catalytic oxidation current was linearly dependent on ascorbic acid concentration in the range 5 × 10⁻⁴–1.6 × 10⁻² M with a correlation coefficient of 0.996. The plot of i _p versus v ^1/2 confirms the diffusion nature of the peak current i _p. Received: 12 April 1999 / Accepted: 25 May 1999     

Anion receptor-coated separator for lithium-ion polymer battery

Anion receptor-coated separators were prepared by coating poly(ethylene glycol) borate ester (PEGB) as an anion receptor and poly(vinyl acetate) (PVAc) as a good adhesive material towards electrodes onto microporous polyethylene (PE) separators. Gel polymer electrolytes were fabricated by soaking them in an liquid electrolyte, 1 M LiPF₆ in EC/DEC/PC (30/65/5, wt.%). As the weight ratio of PEGB to PVAc in a coating layer increased, gel polymer electrolytes showed higher cationic conductivity and electrochemical stability. The cationic conductivity and electrochemical stability of the gel polymer electrolyte based on coated separator with PVAc/PEGB (2/5, weight ratio) could reach 2.8 × 10^–4 S cm^–1 and 4.8 V, respectively. Lithium-ion polymer cells (LiCoO₂/graphite) based on gel polymer electrolytes with and without PEGB were assembled, and their electrochemical performances were evaluated.     

Electrochemistry of Polypyrrole Films in Aqueous Solutions: The Character of the Bond between the Anion and the Polymer Matrix

Mechanisms of the formation and doping of polypyrrole films and their behavior in aqueous media are studied by voltammetry, chronoamperometry, and other methods combined with IR spectroscopy and the tracer technique. The last two methods reveal that pyrrole molecules in acid media form complexes with protons and anions, and that a strong interaction occurs in a polypyrrole film between links of polypyrrole chains and anions, leading to a change in their structure. The obtained data are used to propose a mechanism for the synthesis of polypyrrole films, which includes the discharge of a complex of protonated pyrrole with the anion yielding radical cations, which induce the growth and development of polypyrrole chains. It is stressed that the incorporation of anions into a film (doping) occurs in the course of its formation during the discharge and partial destruction of the pyrrole complexes with the anion.     

Theoretical study on the complexation of the hexafluorophosphate,hexafluoroarsenate, and hexafluoroantimonate anions with dodecabenzylbambus[6] uril

Applying quantum chemical calculations, the most likely conformations of the anionic complex species dodecabenzylbambus[6]uril–PF6−, dodecabenzylbambus[6]uril–AsF6−, and dodecabenzylbambus[6]uril–SbF6− were found. In all these complexes, the considered anions, incorporated in the ligand cavity, are bound by hydrogen bonds between methine hydrogen atoms on the convex face of glycoluril units of the dodecabenzylbambus[6]uril ligand and fluorine atoms of the respective “central” anion. Moreover, the interaction energies of the investigated three anionic complexes were calculated. The absolute values of these calculated energies increase in the series of SbF6− < AsF6− < PF6−.     

In situ conductivity measurements of LiMn2O4 thin films during lithium insertion/extraction by using interdigitated microarray electrodes

Thin films of LiMn₂O₄ have been prepared by RF magnetron sputtering on interdigitated microarray electrodes. In situ conductivity–potential profiles and cyclic voltammograms during extraction/insertion processes of Li ions were obtained simultaneously in nonaqueous and aqueous electrolyte solutions (1 M LiClO₄/propylene carbonate and 1 M LiCl/water). The electronic conductivity of Li_{1– x} Mn₂O₄ was found not to show metallic transition and maintain its semiconducting state during the extraction/insertion of Li ion. A slight decrease in conductivity was observed with increasing the anodic potential, i.e., with increasing x (lithium extraction) and recovered reversibly when the potential returned to the cathodic side (re-insertion of Li ions). Similar results were obtained in both aqueous and nonaqueous electrolyte solutions. Received: 17 June 1997 / Accepted: 2 January 1998     

Striking selectivity of anion incorporation into polypyrrole by competitive doping: perchlorate versus hexafluorophosphate

In the electro-oxidative preparation of polypyrrole films from electrolyte media containing both perchlorate and hexafluorophosphate anions a striking selectivity towards ClO₄ was observed, with a three-fold preference for this anion in films from aqueous medium and a greater than ten-fold preference from MeCN. This result is of benefit towards the production of polypyrroles containing complex functionalized dopant anions, since the presence of PF₆ to bolster electrolysis parameters will less readily carry over into the final polymer. PF₆ is particularly useful for this purpose in MeCN, where ClO₄ is inappropriate, being itself too readily incorporated into the polymer from this solvent system.     

Effects of preparation temperature on the conductivity of polypyrrole conducting polymer

An attempt has heen made to investigate the effect of temperature on the conductivity of polypyrrole conducting polymer films prepared by an electrochemical method in an aqueous medium using camphor sulfonate as the dopant. The polymer was grown from aqueous solutions employing a range of temperatures (l–60°C). It was found that with increase in temperature the conductivity decreased and the optimum temperature was found to be between 10 and 30°C. The results showthatthe polymer formed at low temperature has higher conductivity and is stronger than that formed at higher temperatures. Characterization by X-ray scattering shows that interlayer distance, d_Bragg (?), increases with increasing temperature. The morphology of the films formed was studied by using a scanning electron microscope (SEM). The changes in conductivity and physical appearance were interpreted as being due to compactness in the molecular packing and formation ofαβ linkages in the film.     

Polymer electrolytes based on acrylonitrile-butadiene-styrene copolymer

One of the approaches to improving the ionic conductivity and the mechanical strength of a solid polymer electrolyte is to use polymers in modified forms, such as polymer blends, copolymers and cross-linked polymers. In this study, a new polymer electrolyte based on the acrylonitrile-butadiene-styrene (ABS) copolymer has been prepared. The ionic conductivity, electrochemical stability and interfacial characteristics of the polymer electrolyte in contact with a lithium electrode have been investigated. The temperature dependence of the conductivity below 20 °C can be described by the Arrhenius equation, and above 20 °C by the VTF equation. Lithium passivation appeared to have taken place in the system. The conductivity and electrochemical characteristics of the system are somewhat similar to those of PAN-based polymer electrolytes. Received: 9 December 1998 / Accepted: 9 March 1999     

Attempt to incorporate ferrocenecarboxylic acid into polypyrrole during the electropolymerization of pyrrole in chloroform: its application to the electrocatalytic oxidation of ascorbic acid

 In this work, polypyrrole films with ferrocenecarboxylic acid incorporated (PPy/FCA) were prepared on a glassy carbon (GC) electrode in chloroform as an aprotic solvent with low dielectric constant, convenient for the preparation of the films by a precipitation mechanism. The electrochemical behaviour of the PPy/FCA-coated GC electrode was studied by cyclic voltammetry in aqueous solution with low pH. The results obtained show that the electrochemical response of FCA incorporated in polypyrrole is consistent with a reversible surface oxidation. An obvious electrocatalytic effect of PPy/FCA on the oxidation of ascorbic acid is observed in aqueous solution. Received: 30 July 1998 / Accepted: 3 March 1999