低能离子对高温超导YBa_2Cu_3O_(7-δ)薄膜的表面改性和机理

低能氩离子束轰击并后退火处理的离子束表面改性,会影响高温超导薄膜的表面结构和超导特性,但是其中的深刻微观机理不清楚.本文通过连续改变离子束轰击时间,系统研究了离子束表面改性对于超导膜结构和临界电流密度的影响.通过扫描电子显微镜、X射线衍射、J_(c-scanning)测试表征样品的结构特性和超导特性,并得出内应变、氧空位缺陷等参量.研究表明,经过表面改性的钇钡铜氧(YBa_2Cu_3O_(7-δ),YBCO)薄膜,随轰击时间增加表面形貌会变得更加均匀致密,a轴晶粒消失,并且临界电流密度有了显著的提高.由化学键收缩配对模型分析得出,临界电流密度的提高与薄膜内应变增大和引发的局部YBCO结构中Cu—O键收缩有关.     

插入二氧化铈薄膜提高MOD-YBa2Cu3O7-x厚膜超导性能的研究

YBa₂Cu₃O_7-x(YBCO)膜存在“厚度效应”: 随着厚度增加, YBCO薄膜的临界电流密度下降, 尤其是YBCO薄膜的厚度超过1 μm时, 它的临界电流密度急剧下降. 本文在YBCO薄膜之间引入极薄的二氧化铈(CeO₂)薄膜, 成功制备出结构为YBCO/YBCO/CeO₂/YBCO的超导厚膜. 所制备的厚度为2 μm的YBCO膜临界电流密度为1.36 MA/cm² (77 K, 自场), 其性能比相同厚度的纯YBCO膜有了较大幅度的提升. 研究表明CeO₂薄膜起到了传递织构、松弛应力的作用.     

Tuning the absorption band in the THz range of YBCO films patterned by means of HEHI lithography

High energy heavy ion lithography was used for modulating through implanted nanostructures the local structural and electrical properties of high temperature superconducting YBa₂Cu₃O₇ films. The controlled reduction of the critical temperature of irradiated films results in a localization into heavy ion patterned micro-regions of the electrical dissipation, viable in a given temperature range and driven by ion fluence, bias current and applied magnetic field. The measurement of the response of such nanostructured YBCO films to electromagnetic radiation in the infrared band (MIR–FIR region) is presented. It turns out that the ion induced structural modification of both superconducting film and substrate is actually enabling the infrared optical absorption of YBCO, so that the viability of low noise THz detection above the liquid nitrogen temperature is shown.     

Ferromagnet/superconducting YBa2Cu3O7−δ bilayer devices

A magnetic fringe-field effect has been investigated for a simple bilayer device structure consisting of a Co_0.9Fe_0.1 film and an epitaxial YBa₂Cu₃O_7−δ (YBCO) film patterned as a microbridge. The resistance of the bridge is measured with a four-probe technique and is found to depend on the orientation of a magnetic field, which is externally applied in the device plane. A maximum (minimum) of the resistance occurs when the magnetic field is applied in parallel (perpendicular) to the bridge axis. The difference between the maximum and the minimum is very large for a small range of temperature below the critical temperature of the YBCO film. The observed features in the resistance are qualitatively explained by vortex motion in the YBCO bridge under the influence of the magnetic fringe-field of the Co_0.9Fe_0.1 film.     

SiO2 passivation film effects on microwave characteristics of YBa2Cu3O7−x-based resonators

SiO₂ film coated as a passivation layer for YBa₂Cu₃O_7−x (YBCO)-based microwave devices is investigated by measuring the microwave characteristics of microstrip line resonators. The SiO₂ film is deposited with its 0.3 to 0.4 μm thickness by a sputtering method using Ar + 30%O₂ plasma. These deposition conditions do not degrade the microwave characteristics and the critical temperature (T_c). Next, the SiO₂ film coated resonators are compared with the uncoated ones for two kinds of degradation conditions: a 200°C annealing in air, and an exposure to air at 85°C and 85% RH (relative humidity). We find that the SiO₂ passivation film prevents the YBCO thin film from the surface degradation and reacting with water.     

Enhanced flux pinning in pulsed laser deposited Y Ba2Cu3O7−δ : BaTiO3 nanocomposite thin films

The effect of incorporation of BaTiO₃(BTO) nanoparticles on the flux pinning properties of pulsed laser deposited YBCO:BTO thin films was studied. Substantial increase in the critical current density (J_C) and the pinning force density (F_p) of the nanocomposite thin films was observed. At 77 K, and zero applied magnetic field, the value of J_C for YBCO and YBCO:BTO (2%) thin films were 2.93 MA/cm² and 6.43 MA/cm², respectively. At the same temperature and an applied magnetic field of 4 T, the value of J_C increases from 3.6×10⁴ A/cm² for YBCO thin film to 2.7×10⁵ A/cm² for YBCO:BTO (2%) nanocomposite thin film. The study of temperature and field dependence of of YBCO and YBCO:BTO thin films indicates similar type of pinning. The lattice mismatch between YBCO and BTO seems to introduce more defects resulting in the improvement of flux pinning properties.     

掺杂Y2O3和BaCeO3提高MOD-YBCO超导性能的研究

本文通过在前驱液中添加过量钇盐和铈的有机盐,采用三氟乙酸盐-金属有机沉积法(TFA-MOD) 在铝酸镧单晶基体上制备了含有纳米氧化钇和纳米铈酸钡的YBCO薄膜. 与纯YBCO薄膜相比,掺杂Y₂O₃/BaCeO₃的YBCO膜的临界转变温度几乎保持不变,为91 K左右. 而掺杂Y₂O₃/BaCeO₃的YBCO膜的临界电流密度达到5.0 MA/cm² (77 K, 0T), 是纯YBCO膜临界电流密度的1.5倍.薄膜中的Y₂O₃和BaCeO₃可能在YBCO内部起到了 有效的钉扎磁通作用. 关键词： 钇钡铜氧薄膜 2O₃和纳米BaCeO₃')" href="#">纳米Y₂O₃和纳米BaCeO₃ 磁通钉扎 三氟乙酸盐-金属有机沉积     

High critical current density YBa2Cu3O7−δ tapes prepared by the surface-oxidation epitaxy method

YBa₂Cu₃O_7−δ (YBCO) films with high critical current density (J_c) were successfully fabricated on nickel tapes buffered with epitaxial NiO. NiO was prepared on the textured nickel tape by the surface-oxidation epitaxy (SOE) method. We have reported so far a critical temperature (T_c) of 87 K and J_c=4–6×10⁴ A/cm² (77 K, 0 T) for the YBCO films on NiO/Ni tapes. To enhance the superconducting properties of the YBCO films on the SOE-grown NiO, depositions of thin oxide cap layers such as YSZ, CeO₂, and MgO on NiO were investigated. These oxide cap layers were epitaxially grown on NiO and provided the template for the epitaxial growth of YBCO films. Substantially improved data of T_c=88 K and J_c=3×10⁵ A/cm² (77 K, 0 T) and 1×10⁴ A/cm² (77 K, Hc, 4 T) were obtained for YBCO film on NiO, by using a MgO cap layer with a thickness of 50 nm. The method described in this paper is a simple way to produce long YBCO tape conductors with high-J_c values.     

YBCO线圈在低温下的温度仿真分析

近几年,高温超导线材的制造技术已日趋成熟。作为第二代高温超导带材的代表,YBCO在低温下具有的优点使其在超导磁体领域的应用越来越突出。但是在高温超导磁体的运行中会因为受到扰动而失超。为了探讨这个问题,模拟了一个磁体在低温下(20K左右)有加热点扰动时的稳定性情况,即对YBCO线圈在低温下的工作情况进行了模拟仿真。文中根据实验设计的YBCO单饼线圈参数,利用热传导方程和基本电路方程,采用有限元计算方法,模拟出线圈内部的温度分布。分析仿真结果可以为后续实验设计提供参考。     

Linear and nonlinear critical magnetic properties and transport in Nd0.75Ba0.25MnO3 single crystal: evidence for its anomalous critical behavior near TC

The data on the resistance and magnetoresistance (MR) as well as measurements of the linear and nonlinear susceptibilities are presented for a Nd_0.75Ba_0.25MnO₃ single crystal with the Curie temperature T_C≈129 K. Although this compound remains insulating in the ferromagnetic state, its resistance has an anomaly near T_C and it reveals the colossal magnetoresistance. The data on the magnetic response are well described by the dynamic scaling theory for 3D isotropic ferromagnets in the paramagnetic critical region at τ>τ^*≈0.11, τ=(T−T_C)/T_C. Below τ^* an anomalous critical behavior is found that suggests the coexistence of two magnetic phases. This behavior is discussed in terms of a phase separation which can occur in the moderately doped manganites exhibiting an orbital ordering.     

Influence of MgO surface conditions on the in-plane crystal orientation and critical current density of epitaxial YBCO films

The effect of magnesium oxide (MgO) surface conditions on in-plane grain orientation and critical current density of epitaxial YBa₂Cu₃O₇ (YBCO) films was systematically investigated. The MgO substrates were either “as received” or stored for some time, cleaned using different methods and lithographically prepared for our step-edge junction devices. The YBCO films were grown via reactive thermal co-evaporation by Theva, GmbH. The surface characterisation of MgO substrates was studied using X-ray photoelectron spectroscopy (XPS). The in-plane grain orientation of the YBCO films was studied by means of X-ray diffraction (XRD) φ-scan and the critical current density was measured for the XRD scanned samples. The surface condition of the MgO substrates was found to have a strong influence on the in-plane grain orientation and the critical current density of the YBCO films. The MgO substrates with a degraded or contaminated surface gave rise to 45° grain misorientation in YBCO films and reduced the critical current density. A final process step using a low energy Ar ion beam etching (IBE) of the MgO substrates prior to the YBCO film deposition was found effective in removing the in-plane grain misorientation and promoting the growth of perfectly aligned c-axis YBCO films.     

Fabrication of YBCO／YSZ and YBCO／MgO thick films using electrophoretic deposition with top-seeded melt growth process

Superconducting thick films were grown on single crystals MgO and YSZ by electrophoretic deposition with Y_2BaCuO_5(Y211) addition. YBCO thick films were then accomplished by sintering the precursor films above the peritectic temperature. Single crystals of MgO (3×3×0.5 mm^3) were used as top-seed to control crystal structure of the thick films. As shown by scanning electron microscopy, the morphologies of YBCO/YSZ and YBCO/MgO thick films are spherulitic texture and platelet type. The critical temperature is ～89 K for the YBCO/YSZ thick film; the onset transition temperature is 86.4 K and the transition width is ～3 K for YBCO/MgO thick film. The critical current densities (as determined by Bean model) are, in A/cm^2, 3870 (77 K) for YBCO/YSZ thick films and 2399 (77 K) for YBCO/MgO thick films, which are comparable to the best J_c reported of the thick films prepared by the same method.     

NON-EQUILIBRIUM MICROWAVE RESPONSE OF Yba2Cu3O7-δ GRANULAR THIN FILMS UNDER MAGNETIC FIELDS

Microwave responses of YBa₂Cu₃O_7-δ(YBCO) granular film have been studied at the microwave frequency of 30.5 GHz. In the absence of a magnetic field the dependence of a normal microwave response on the bias current is observed at a temperature close to T_c. When a magnetic field ranged from 5.0 mT to 33.0 mT is applied, the responses broaden and shift toward a lower temperature. In the superconducting state, the responses were found to be highly dependent on the magnetic field. For the current equal to 5.0mA and a magnetic field above 17.0mT the response increases and did not vanish even at a very low temperature, the fact is believed to be correlated to the anisotropic character of the structure.     

GROWTH MODE OF Cu-RICH PARTICLES ON LASER-ABLATED YBa2Cu3O7 THIN FILMS

The microstructure of the laser-ablated YBa₂Cu₃O₇ (YBCO) thin film deposited on heated (100) SrTiO₃ substrate was examined by transmission electron microscope. The par-ticles on the film mainly consist of CuO and few CuYO₂. Most of these non-superconducting particles nucleate on or near the surface of the film and protrude about 100-400 nm in height, A large amount of a-axis YBCO grains also exist in the film, which nucleate at the substrate surface and grow perpendicularly above the c-axis YBCO film. The YBCO thin film deposited under low oxygen pressure has very different microstructure compared with YBCO thin film deposited under high oxygen pressure.     

YBCO/聚丙烯腈杂化膜及其超导性研究

报告了一种简单制备不依赖于基底结构的柔性YBCO/聚丙烯腈（PAN）厚膜的新方法.研究结果发现,PAN含量从0增加到10wt%的过程中,全部YBCO/PAN样品的超导临界温度T_c在900—920 K区间,表现出较好的超导电性.而且当PAN含量为10wt%时,YBCO/PAN杂化膜即具有一定柔性,膜厚约35 μm,临界电流密度Jc=29×10⁴Acm^-2(1 T, 10 K)和J< 关键词： 超导电性 YBCO 聚丙烯腈（PAN） 杂化膜     

Effect of different oxidizing gases on the in-situ growth of YBa2Cu3O7−δ films by pulsed laser deposition

The effectiveness of oxygen (O₂), nitrous oxide (N₂O), and nitrogen dioxide (NO₂) as oxidizing agents during in-situ growth of YBa₂Cu₃O_7−δ (YBCO) films on (100) SrTiO₃ substrates by pulsed laser deposition has been studied as a function of deposition temperature (700–800°C), and laser wavelength (193,248 and 355 nm), for a wide range of oxidizer gas pressure (0.1–200 mTorr). In general, the superconducting transition temperature of the films has been found to increase with increasing oxidant pressure, with zero-resistance temperature ≈90 K only obtained in films prepared in a relatively high pressure (150–200 mTorr) of oxidizer gas. At lower pressures, the transition temperature while being depressed is quite sensitive to the nature of the oxidant, the laser wavelength and the deposition temperature. Nevertheless, independent of the oxygen source or other growth parameters, an almost linear decrease in transition temperature with a corresponding increase in the c-axis lattice parameter has been observed for all the film. YBCO films have also been deposited in a low pressure background (≤ 1 mTorr) using a combination of atomic oxygen and pulsed molecular oxygen. The results are discussed in terms of the oxygen requirement for kinetic and thermodynamic stability of YBCO during growth of the film by pulsed laser deposition.     

The effect of Ag or Au overlayers on underlying YBa2Cu3O7 thin films

Although Ag and Au are commonly used to provide low-resistance contacts to YBa₂Cu₃O₇ (YBCO), their effect on the electrical properties of the underlying YBCO has been largely neglected. Epitaxial YBCO thin films on LaAlO₃ substrates were used in this study. Thin (50 nm) and thick (1 μm) layers of Ag or Au were deposited as overlayers, and in some cases annealed in oxygen at 550–650°C. Compared to samples with no metal overlayers, for both Ag and Au the normal-state parameters changed (resistivity, its temperature coefficient, and the transition width), whereas the transition temperature and critical current density remained unaltered. These results are encouraging for the use of these metals as contacts and/or conducting overlayers on YBCO.     

Nb/Au/(1 1 0)YBa2Cu3O7−δ Josephson junctions: evidence against atomic scaled “corner junctions”

We report on I–V characteristics for in situ formed Nb/Au/(1 1 0)YBa₂Cu₃O_7−δ (YBCO) Josephson junction, where the homoepitaxial (1 1 0)YBCO film shows ultra-smooth surface morphology. The field dependence of critical supercurrent I_c shows anisotropic large junction behavior with normal Fraunhofer patterns expected from BCS model of d_x²−y² wave superconductors. This strongly suggests that the Nb/Au/(1 1 0)YBCO junctions cannot be regarded as atomic scaled corner junctions, in contrast with (0 0 1)/(1 1 0)YBCO grain boundary junctions to show “π-junction” with a pronounced dip near zero fields in field modulation of I_c.     

PREPARATION OF a-AXIS ORIENTED YBa2Cu3Ox THIN FILMS

The a-axis oriented YBa₂Cu₃O_x(YBCO) thin films could be grown on (100) SrTiO₃(STO) substrates with STO buffer layers by dc and rf magnetron sputtering either by low-ering the deposition temperature, or by using a self-template technique. For the latter, the resistivity of the thin film at 290K along the substrate [001] direction is about four times larger than that in the [010] direction. The zero resistance temperatures T_c0 are 89 K in both directions. So high quality a-axis oriented YBCO thin films can be prepared by the self-template technique. Also the T_c0 increase monotonously with the reduction of the thickness of the YBCO seed layer.     

TFA-MOD法制备YBCO薄膜生长速率研究

采用原位电阻法对TFA-MOD法高温热处理阶段YBCO薄膜生长速率进行了研究。实验结果和分析表明原位电阻测量法是一种估算YBCO层生长速率的有效方法,不同条件下的测量结果表明薄膜生长速率随管式炉内的温度、水分压、气体流量的上升而明显增加,但随薄膜面积的增加而减小。实验结果为进一步探索和优化热处理过程提供了重要的基础。