Automated sample preparation based on the sequential injection principle. Solid-phase extraction on a molecularly imprinted polymer coupled on-line to high-performance liquid chromatography

A molecularly imprinted polymer (MIP) prepared using caffeine, as a template, was validated as a selective sorbent for solid-phase extraction (SPE), within an automated on-line sample preparation method. The polymer produced was packed in a polypropylene cartridge, which was incorporated in a flow system prior to the HPLC analytical instrumentation. The principle of sequential injection was utilised for a rapid automated and efficient SPE procedure on the MIP. Samples, buffers, washing and elution solvents were introduced to the extraction cartridge via a peristaltic pump and a multi-position valve, both controlled by appropriate software developed in-house. The method was optimised in terms of flow rates, extraction time and volume. After extraction, the final eluent from the extraction cartridge was directed to the injection loop and was subsequently analysed on HPLC. The overall set-up facilitated unattended operation, operation and improved both mixing fluidics and method development flexibility. This system may be readily built in the laboratory and can be further used as an automated platform for on-line sample preparation.     

Coupling of sequential injection with liquid chromatography for the automated derivatization and on-line determination of amino acids

The principle of sequential injection (SI) was exploited to develop a fully automated pre-column derivatization procedure combined on-line to liquid chromatography (LC). Using SI-LC derivatization 14 amino acids were determined fluorimetrically in pharmaceuticals with o-phthaldialdehyde (OPA) as the derivatization reagent. The SI system was used for the handling of samples and reagents, on-line mixing and introduction to the LC injection system. Chemical (pH and reagents concentrations) and instrumental variables (sample and reagent volumes, reaction time and flow rate) were optimized to attain the highest reaction yield and detector signal. Reversed phase chromatographic resolution of 14 amino acids was achieved within 35 min using gradient elution. The automated operation of the coupled SI-LC system resulted in very satisfactory performance. The method was applied for the simultaneous determination of amino acids in pharmaceutical formulations.     

An automated solid sample analysis system

Summary An automated solid sampling analysis system (SSAS) consisting of a powder sampler, an integrated microbalance, a transport and handling system for the sample boat, a microcontrolling unit for all necessary steps and an appropriate AAS instrument is described in detail and its potential for routine metal determination in various materials is demonstrated.     

Automatic determination of urinary 4-hydroxy-3-methoxymandelic (vanillylmandelic) acid by liquid chromatography with electrochemical detection

An automated liquid chromatographic method for the determination of urinary concentrations of 4-hydroxy-3-methoxymandelic acid (VMA) is described. Urine samples are purified by solid-phase extraction on an anion-exchange cartridge and automated on-line chromatographic elution is carried out using a Varian AASP (advanced automated sample processor) system. The column effluent is monitored with an electrochemical detector using a glassy carbon working electrode. The method allows the determination of VMA in 0.05 ml of normal urine with a relative standard deviation of less than 3%. The analysis time can be shortened by use of back-flushing technique, and the correlation with a classical (but non-automated) VMA analysis method is excellent.     

Application of totally automated on-line sample clean up for prostanoid extraction and HPLC separation

Summary The aim of this study has been the evaluation of an automated system for on-line sample preparation using solid phase extraction and HPLC purification for the measurement of prostanoids in urine. We have established the optimum precolumn and column conditions for this analysis. The manual extraction —HPLC procedure furnishes lower recoveries and higher coefficients of variation than those obtained by the automated on-line procedure. The automated system has been applied to prostanoid analysis of human urine samples from subjects exposed to lead.     

Chromium speciation using an automated liquid handling system with inductively coupled plasma - mass spectrometric detection

The speciation of inorganic chromium in environmental samples is required for accurate assessment of pollution levels. Of the two chromium oxidation states, Cr (VI) is a known carcinogen, while Cr (III) is an essential element. Total chromium measurement cannot be used to determine actual environmental impact due to the considerable difference in toxicity of the two elemental forms. An automated liquid handling system, the PrepLab™, can be used with an inductively coupled plasma-mass spectrometer (ICP-MS) to quantify Cr (III) and Cr (VI) in liquid samples. An autosampler is used to introduce discrete sample volumes into a solid-phase chelation resin column. The Cr (III) and Cr (VI) species are separated and are introduced on-line into the VG PlasmaQuad 3 ICP-MS for detection. The chromatographic data are collected in time resolved analysis mode with the capability of simultaneous multiple-isotopic detection.     

Development of automated analytical systems for large throughput

The need to be able to handle a large throughput of samples for neutron activation analysis has led to the development of automated counting and sample handling systems. These are coupled with available computer-assisted INAA techniques to perform a wide range of analytical services on a commercial basis. A fully automated delayed neutron counting system and a computer-controlled pneumatic transfer for INAA use are described, as is a multi-detector gamma spectroscopy system.     

A fully automated catecholamines analyzer based on cartridge extraction and HPLC separation

Summary A fully automated analyzer is described for the HPLC analysis of catecholamines. Firstly urinary and plasma catecholamines are reacted with diphenylboronic acid giving a complex without requiring a pH-meter step. This complex is strongly retained on a C 18 cartridge and elution with acetic acid solutions shows recoveries higher than 90 %. The catecholamines are eluted also by the mobile phase employed for the HPLC’ analysis. An intelligent autosampler makes the complex and fills a loop with all the solvents necessary for the sample cleanup. It then inverts the flow and pumps the sample and the solvents throught the cartridge. In the elution step the disposable extraction cartridge is positioned on stream with the HPLC analytical column by an automatic sampler. The separation is performed by ion-pair reversed-phase high-performance liquid chromatography, with sodium dodecyl sulphate as pairing ion, a short analytical column and electrochemical detection. The HPLC analysis time is 3 min and the total sample turnover time is 8 min. The recoveries and the precision of the analyzer are given together with correlation with manual HPLC.     

Determination of Zy 17617B in plasma by solid-phase extraction and liquid chromatography with automated pre-column exchange.

An automated chromatographic system, combining solid-phase extraction and automated pre-column exchange, is described for the routine determination of Zy 17617B at the pmol/ml level in human plasma. The sample extraction and elution onto the analytical column were performed automatically and concomitantly using a conventional liquid chromatographic apparatus equipped with a Merck OSP-2 on-line sample preparator. Validation data demonstrate the reliability of the method.     

Development of an automated on-line pre-column derivatization procedure for sensitive determination of histamine in food with high-performance liquid chromatography-fluorescence detection

An improved sensitive method was developed and validated for the determination of histamine in food samples by using automated on-line pre-column derivatization coupled with high performance liquid chromatography and fluorescence detection (HPLC-FLD). o-Phthaldialdehyde (OPA) was adopted as derivatization reagent, and a "sandwich" (OPA+histamine+OPA) aspiration mode for the automated on-line pre-column derivatization was found to efficiently enhance the method sensitivity and precision. Histamine in food samples was efficiently extracted with a methanol-phosphate buffer solution (50:50, v/v) at 60 degrees C for 30 min, and purified with Waters Oasis MCX solid-phase extraction (SPE) cartridge. The limit of quantification for this method is 0.2 mg/kg, which is very sensitive for histamine determination. With the "sandwich" injection program, 3.7% of relative standard deviation (RSD) was achieved by five replicative determinations of a sample blank spiked with 0.25 mg/kg histamine standard. Histamine in food samples such as fumitory skipjack and mackerel was analyzed with relative recoveries over 95% at spiking level of 150 mg/kg, as well as canned tuna fish and cheese with relative recoveries up to 98% at spiking levels of 0.50 and 5.0 mg/kg, respectively. The proposed method was validated with a sample from the Food Analysis Performance Assessment Scheme (FAPAS) as a standard certified material; and the results (140+/-6 mg/kg) agreed well with the assigned value (139 mg/kg).     

Automated sample handling by extraction techniques

Laborious and time-consuming sample pre-treatment has resulted in the development of automated sample handling systems which can be coupled on-line with several analytical techniques.     

Development of an automated method for determining oil in water by direct aqueous supercritical fluid extraction coupled on-line with infrared spectroscopy

A direct aqueous supercritical fluid extraction (SFE) system was developed which can be directly interfaced to an infrared spectrometer for the determination of oil in water. The technique is designed to provide an environmentally clean, automated alternative to established IR methods for oil in water analysis which require the use of restricted organic solvents. The SFE-FTIR method involves minimum sample handling stages, with on-line analysis of a 500 ml water sample being complete within 15 min. Method accuracy for determining water samples spiked with gasoline, white spirit, kerosene, diesel or engine oil was 81-100% with precision (RSD) ranging from 3 to 17%. An independent evaluation determined a 2 ppm limit of quantification for diesel in industrial effluents. The results of a comparative study involving an established IR method and the SFE-FTIR method indicate that oil levels calculated using an accepted equation which includes coefficients derived from reference hydrocarbon standards may result in significant errors. A new approach permitted the derivation of quantification coefficients for the SFE-FTIR analyses which provided improved results. In situations where the identity of the oil to be analysed is known, a rapid off-line SFE-FTIR system calibration procedure was developed and successfully applied to various oils. An optional in-line silica gel clean-up procedure incorporated within the SFE-FTIR system enables the same water sample to be analysed for total oil content including vegetable oils and selectively for petroleum oil content within a total of 20 min. At the end of an analysis the SFE system is cleaned using an in situ 3 min clean cycle.     

Determination of melagatran in rabbit plasma by high-performance liquid chromatography with automated column switching

Melagatran is an active thrombin inhibitor showing oral and parenteral bioavailability for antithrombotic therapy. A simple and convenient liquid chromatographic method has been developed and applied to the analysis of melagatran in rabbit plasma. The clean-up and separation of the sample solutions were performed by automated on-line column switching HPLC. The method validation shows the suitability of the column switching liquid chromatographic system for the quantitation of melagatran in biological fluids.     

In-Valve Sample Preparation Cartridge Designed for Microcolumn Liquid Chromatography

Miniaturized sample preparation technique for complex sample matrices has been developed with a polymer-coated fibrous extraction medium. By using extraction cartridge packed longitudinally with polymer-coated fiber into a short PEEK capillary, the extraction efficiency was significantly improved. The extraction cartridge was installed in an injection valve as a sample loop and the on-line coupling with microcolumn liquid chromatography (micro-LC) was demonstrated. This on-line coupled sample preparation/separation system showed a good validity for the analysis of phthalates and tricyclic antidepressant drugs in typical water samples. The lowest limits of quantification for several phthalates and tricyclic antidepressants (TCA) drugs were less than 1 ng mL^?1. The effect of polymeric coating on the filament surface on the extraction power was also investigated.     

Synthesis and analysis of combinatorial libraries performed in an automated micro reactor system

This paper presents the synthesis of combinatorial libraries performed on a single-channel glass micro reactor under hydrodynamic flow control. The experiments were carried out in a non-well based micro chip and consisted of the preparation of libraries of pyrazoles by means of a Knorr reaction of 1,3-dicarbonyl compounds with hydrazines. The aim of this work is to investigate the capabilities of an automated micro reactor based system to synthesise sequentially multiple analogue reactions. Small slugs of reactants were introduced automatically by an autosampler in a serpentine-etched glass chip. The mobility of the reagents and products was achieved using hydrodynamic driven flow. Reaction slug dilution and UV slug detection took place at the outlet. A sample of the slug was analysed by using an on-line LC-UV-MS system. The degree of conversion was quantified using the UV signal and comparing with standards of starting materials and final products. After the LC-UV-MS analysis, the automated system proceeds to inject the slugs to carry out the next reaction programmed. The results suggest that the micro reactor system is capable of repeating the process of injection, mixing and reaction in an automated manner as many times as required.     

Interpretation system for automated wavelength dispersive X-ray fluorescence spectrometry

A prototype expert system for automated interpretation of wavelength dispersive X-ray fluorescence spectra is described. The system consists of two main components: a pre-processor (PREXRF) written in BASIC and a knowledge handling part (INFERXRF) that contains the knowledge base and the inference engine implemented in PROLOG. Both systems rely heavily on the theory of fuzzy sets in an attempt to deal with incomplete and uncertain information. The performance of the interpretation system for automated analysis of simulated and measured samples is demonstrated.     

A fully automated system for inorganic antimony preconcentration and speciation in urine

A study was undertaken to ascertain the analytical capabilities of l-methionine immobilized on controlled pore glass for Sb preconcentration and speciation. A fully automated on-line system, implemented with hydride generation (HG) and inductively coupled plasma optical emission spectrometry (ICP OES), was used. Sb(III), at pH 10 was selectively retained in the column containing the immobilized aminoacid, while Sb(V) was not retained at all. A 30% HCl solution was used as eluent agent. Prior to total Sb determination, a pre-reduction step with thiourea was necessary. An on-line pH adjusting and pre-reduction of Sb(V) was achieved in a fully automated system. The detection limit for the preconcentration of 10 mL of an aqueous solution was 70 ng L⁻¹ with a relative standard deviation of 2%. An enrichment factor of 20 was achieved when 10 mL of sample was passed through the system, reaching a throughput of 23 samples per hour. The method was successfully applied to the determination of Sb(III) and total Sb in urine.     

Fully automated open access platform for rapid, combined serial evaporation and sample reformatting

This paper reports a novel evaporator and its integration with an automated sample handling system to create a high throughput evaporation platform. The Vaportec V-10 evaporator uses a high speed rotation motor ( approximately 6000 rpm) to spin the vial containing a sample, creating a thin film of solvent which can be readily evaporated by the application of heat to the vial, while the consequent centrifugal force prevents "bumping". An intelligent algorithm controls pressure and temperature for optimum solvent removal conditions and end of run detection, critical for automation. The system allows the option of evaporation directly from a sample source vial, or alternatively, integrated liquid handling facilities provide the capability of transferring samples portionwise from a (large) source vial or bottle to a (small) daughter container, enabling efficient sample reformatting, with minimum user intervention. The open access system makes significant advances over current vacuum centrifugal evaporators in terms of evaporation rate and ease of automation. The evaporator's main features, the integration of robotics to provide automation, and examples of evaporation rates of a wide range of solvents from a variety of containers are described.     

Development and validation of an isotope-dilution electrospray ionization tandem mass spectrometry method with an on-line sample clean-up device for the quantitative analysis of the benzene exposure biomarker S-phenylmercapturic acid in human urine

An isotope-dilution electrospray ionization tandem mass spectrometry (ESI-MS/MS) method with an on-line sample clean-up device, for the quantitative analysis of human urine for the benzene exposure biomarker S-phenylmercapturic acid (SPMA), was developed and validated. The sample clean-up system was constructed from an autosampler, a reversed-phase C18 trap cartridge, a two-position switching valve, and controlling computer software and hardware. The sample clean-up system was interfaced via 1/20 splitting to the ESI source of a triple-quadrupole mass spectrometer using negative ion mode and multiple reaction monitoring for SPMA and the isotope-labeled internal standard. A strategy was adopted to acquire pooled blank urine matrix and quality control samples spiked with standards. Validated procedures and data on method specificity, detection limits, standard curves, precision and recovery, sample storage stability, and inter-laboratory comparison are presented. The analytical system was fully automated. No tedious manual sample clean-up procedures are required. With the selectivity and the sensitivity provided by ESI-MS/MS detection, the analytical system can be used for high-throughput and accurate determination of SPMA levels in human urine samples, as a biomarker for environmental as well as occupational benzene exposure.     

Fully automated determination of 74 pharmaceuticals in environmental and waste waters by online solid phase extraction-liquid chromatography-electrospray-tandem mass spectrometry

The present work describes the development of a fully automated method, based on on-line solid-phase extraction (SPE)-liquid chromatography-electrospray-tandem mass spectrometry (LC-MS-MS), for the determination of 74 pharmaceuticals in environmental waters (superficial water and groundwater) as well as sewage waters. On-line SPE is performed by passing 2.5 mL of the water sample through a HySphere Resin GP cartridge. For unequivocal identification and confirmation two selected reaction monitoring (SRM) transitions are monitored per compound, thus four identification points are achieved. Quantification is performed by the internal standard approach, indispensable to correct the losses during the solid phase extraction, as well as the matrix effects. The main advantages of the method developed are high sensitivity (limits of detection in the low ng L⁻¹ range), selectivity due the use of tandem mass spectrometry and reliability due the use of 51 surrogates and minimum sample manipulation. As a part of the validation procedure, the method developed has been applied to the analysis of various environmental and sewage samples from a Spanish river and a sewage treatment plant.