Glass forming ability of the Al–Ce–Ni system

In the present work, the glass forming ability (GFA) and its compositional dependence on Al–Ni–Ce system alloys were investigated as a function of several thermal parameters. Rapidly quenched Al₈₅Ni_15?XCe_X (X = 4,5,6,7,10), Al₉₀Ni₅Ce₅, Al₈₉Ni_2.4Ce_8.6, Al₈₀Ni_15.6Ce_4.4 and Al₇₈Ni_18.5Ce_3.5 amorphous ribbons were produced by melt-spinning and the structural transformation during heating was studied using a combination of X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The results showed that the GFA and the thermal stability in the Al-rich corner of Al–Ni–Ce system alloys were enhanced by increasing the solute content and specifically the Ce content.     

Change in environmental structure around Al in Zr60Ni25Al15 metallic glass upon crystallization studied by nuclear magnetic resonance

In order to investigate the structural evolution around Al, pulse NMR experiments were carried out on ²⁷Al in the Zr₆₀Ni₂₅Al₁₅ metallic glass and the related crystalline compound, Zr₆NiAl₂. Different chemical shift peaks were observed around 2750 and 3000 ppm in the as-quenched Zr₆₀Ni₂₅Al₁₅ and crystalline compound, Zr₆NiAl₂, respectively. Considering that the capped triangular prism of Zr₉Al₃ is formed around Al in the Zr₆NiAl₂ crystal, chemical correlation pairs of Al–Zr and/or Al–Al are fairly faint while that of Al–Ni may be dominant instead in the as-quenched state. These results suggest an inhomogenous chemical bonding nature in the Zr₆₀Ni₂₅Al₁₅ metallic glass. The resonant peaks around 3000 ppm, which were distinctive in the Zr₆NiAl₂ crystal, appeared and became stronger upon crystallization through the relaxed state. Thus, drastic change in the local atomic configuration around Al was confirmed so as to form the unlike chemical correlation pairs of Al–Zr upon crystallization. The high glass-forming ability of the Zr₆₀Ni₂₅Al₁₅ metallic glass should be attributed to the difficulties of significant atomic redistribution of the constituents around Al.     

The Al nano-crystallization process in amorphous Al85Ni8Y5Co2

The primary nano-crystallization of fcc Al in initially amorphous Al₈₅Ni₈Y₅Co₂ has been studied by differential scanning calorimetry (DSC), transmission electron microscopy (TEM) in combination with energy electron loss spectroscopy (EELS), high-resolution transmission electron microscopy (HRTEM) and X-ray diffractometry (XRD). TEM in combination with EELS after both isochronal and isothermal annealing allowed the determination of the change of the crystalline particle density and particle density/size distribution. The crystallization in Al₈₅Ni₈Y₅Co₂ was found to take place in three sequences. In the first step of the first sequence spherical fcc Al nano-particles develop with a very high particle density. In the second step of the first sequence the more or less spherical Al particles develop protrusions without significant further nucleation of fcc Al particles. In the second sequence nucleation of new fcc Al particles takes place. Comparing the crystallization behavior of Al₈₅Ni₈Y₅Co₂ with that of Al₈₅Ni₅Y₈Co₂ it follows that the yttrium solute level has a strong influence on the nucleation and growth behavior during the fcc Al primary nano-crystallization.     

Influence of Gd and Fe on crystallization of Al87Y5Ni8 amorphous alloy

Crystallization of amorphous Al-based alloys (Al-Y-Gd-Ni-Fe) was investigated by applying differential scanning calorimetry (DSC), X-ray diffraction (XRD) and high resolution electron microscopy (HREM). It was shown that the crystallization in the examined alloys proceeds in three stages (DSC maxima). The two first stages are attributed to formation of solid solution of fcc Al(RE) nanograins in amorphous matrix. In the third stage the precipitation of ternary compound Al₁₉Ni₅RE₃ of the orthorhombic Al₁₉Ni₅Gd₃-type structure was observed. A partial substitution of Ni by Fe causes a change of stoichiometry and crystal structure of the ternary compounds: Al₈TM₄RE (TM = Fe, Ni; RE = Y, Gd) of the tetragonal ThMn₁₂ (Al₈Mn₄Ce)-type structure. A partial replacing of Y atoms by Gd in the Al₈₇Y₅Ni₈ based alloy shifts the Al(RE) nanocrystallization to lower temperatures. In contrast to this a partial replacing of Ni by Fe shifts the nanocrystallization to higher temperatures.     

Crystallization behaviors of Al-Ni-La amorphous alloys with trace Ti and B

Effects of the single or simultaneous addition of trace Ti and B (?1 at.%) on the glass-forming ability (GFA) and crystallization behaviors of Al₈₈Ni₆La₆ and Al₈₉Ni₆La₅ amorphous alloys were investigated by X-ray diffraction and differential scanning calorimetry. The addition of trace Ti and B deteriorates the GFA, but improves the thermal stability especially if Ti is added singly. The crystallization onset temperature T_x1 of the first exothermic peak increases by 29.5 and 18.0 K when 1% of the Al atoms in Al₈₈Ni₆La₆ and Al₈₉Ni₆La₅ are replaced by Ti, respectively. However, the primary phase during annealing remains unchanged.     

Crystallization behaviour of Al-based metallic glasses below and above the glass-transition temperature

The present paper aims to report an effect of a supercooled liquid region on crystallization behaviour of the Al₈₅Y_8−xNd_xNi₅Co₂ metallic glasses produced by rapid solidification of the melt. The paper describes the crystallization process at different regimes of heat treatment. It is found that crystallization behaviour of the above-mentioned Al-based metallic glasses above the glass-transition temperature and below it follows different transformation mechanisms. Formation of the primary nanoscale α-Al particles was observed during continuous heating or after isothermal annealing above the glass-transition temperature. During isothermal annealing below the glass-transition temperature an unknown metastable phase is formed conjointly with α-Al. The metastable phase formed in the Nd-free alloy varies from that in the Nd-bearing alloys. Al₈₅Nd₈Ni₅Co₂ amorphous alloy exhibiting no glass transition crystallizes equally during isothermal calorimetry at different temperatures and during continuous heating.     

Fabrication and characterization of metallic glasses with a specific microstructure for micro-electro-mechanical system applications

Metallic glass microstructures with high aspect ratios for micro-electro-mechanical system applications have been fabricated by micro-electro-discharge machining and selective electrochemical dissolution methods. Micro-holes and three-dimensional microstructures machined on the La₆₂Al₁₄Ni₁₂Cu₁₂, Zr₅₅Al₁₀Ni₅Cu₃₀ and Cu₄₆Zr₄₄Al₇Y₃ bulk metallic glasses by micro-electro-discharge machining are evaluated by using X-ray diffraction, scanning electron microscopy, and nanoindentation. The experimental results demonstrate that the machined samples kept their amorphous structure without devitrification, and their machining characteristics are related to the thermo-physical properties of the alloys and the electrode diameters. Porous, single-pore and thin-walled Zr-based metallic glass tubes with micro-pore structures can be prepared by selective electrochemical dissolution method. The high aspect ratio microstructures fabricated by the two methods have the potential applications as micro-nozzles, polymer micro-injection molding tools, micro-channels or micro-flow meters in micro-electro-mechanical system devices.     

Comparative study of the effect of cold rolling on the structure of Al–RE–Ni–Co (RE = rare-earth metals) amorphous and glassy alloys

The present paper aims to compare the deformation-induced crystallization behavior of the rapidly solidified ribbon samples of Al₈₅Y₈Ni₅Co₂, Al₈₅Nd₈Ni₅Co₂, Al₈₅Gd₈Ni₅Co₂ and Al₈₅Mm₈Ni₅Co₂ non-crystalline alloys subjected to cold rolling with 33% reduction. It is found that amorphous Al₈₅Y₈Ni₅Co₂ alloys exhibiting glass-transition and Al₈₅Nd₈Ni₅Co₂ alloys exhibiting no glass-transition have somewhat different stabilities against crystallization under deformation at room temperature though their crystallization temperatures under heating without load or deformation are almost equal. Al₈₅Gd₈Ni₅Co₂ and Al₈₅Mm₈Ni₅Co₂ alloys (Mm = Mischmetal) did not exhibit deformation-induced crystallization at the reduction ratio used. Although, the formation of the primary nanoscale α-Al particles was observed in both Al₈₅Y₈Ni₅Co₂ and Al₈₅Nd₈Ni₅Co₂ alloys after the cold rolling, the size and volume fraction of the particles are larger in the Nd-bearing amorphous alloy as compared to the Y-bearing alloy. It is found that contrary to crystallization on heating no intermetallic compounds but only α-Al nano particles were formed during the deformation-induced crystallization of Al₈₅RE₈Ni₅Co₂ amorphous alloys. The local heating on deformation is hypothesized to affect the crystallization.     

Evaluation of the volume fraction of nanocrystals devitrified in Al-based amorphous alloys

An evaluation of fcc-Al volume fractions (V_f) in Al₉₀Ni₅Nd₅ and Al₈₅Ni₅Y₆Co₂Fe₂ nanostructured composites has been made by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) methods. For the Al₉₀Ni₅Nd₅ alloy, there exhibited lower V_f values obtained by DSC than that by XRD due to increased interface energy and the overlapping of primary crystallization and structural relaxation features during nanocrystallization process. For the Al₈₅Ni₅Y₆Co₂Fe₂ alloy, the V_f values calculated by both methods showed good agreements at low crystallinities, but apparent differences are observed at high crystallinities. This is due to compositional variations in the remaining amorphous matrix during devitrification.     

Studies on the formability of Al-based metallic glasses/nanocomposites based on isochronal DSC analysis

The Al₈₆Si_0.5Ni_4.06Co_2.94Y₆Sc_0.5 metallic glass of highly improved glass-forming ability (GFA) has been investigated by isochronal differential scanning calorimetry measurements, as well as the Al₈₅Ni₅Co₂Y₈ for comparison. The experimental results indicate that the Al₈₆Si_0.5Ni_4.06Co_2.94Y₆Sc_0.5 exhibits enlarged temperature interval between the first and second crystallization onsets (termed as primary fcc-Al/glass region), as well as enlarged second activation energy (E_p2) against the nucleation and the growth of intermetallic compounds besides fcc-Al. The variation of the Avrami exponent demonstrates that the primary crystallization process is a rapid two- and three-dimensional diffusion-controlled nucleation and growth mechanism initially, and the whole process is strongly controlled by the growth of fcc-Al crystals. According to the analysis on the basis of atomic mobility of alloy components, it demonstrates that the enlarged primary fcc-Al/glass region obtained through proper coexistence of dissimilar and similar elements would be in favor of preparing Al-based metallic glasses or nanocomposites in greater size.     

Structure and morphology of [icosahedral Al62Cu25.5Fe12.5]100−x[decagonal Al70Co15Ni15]x alloys, for x=10(03 and 510)

Alloys made from mixtures of Al₆₂Cu_25.5Fe_12.5 icosahedral quasicrystal (IQC) and Al₇₀Co₁₅Ni₁₅ decagonal quasicrystal (DQC) were studied by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The transition from IQC to DQC was thus discussed by studying the evolution of their constituent phases in each alloy. Three approximant phases were found as common phases in most of the pseudo-binary alloys: λ-Al₁₃Fe₄, β-AlFe and τ3-Al₃Ni₂. It is found that, with the increment of the DQC content in the alloy, the λ phase changes from Al₁₃Fe₄ to Al₁₃Co₄ and the τ3 phase changes from Al₃Cu₂ to Al₃Ni₂. The formation of these phases were found also to follow the evolution of their corresponding e/a-constant lines in the Al–(Cu,Ni)–(Fe,Co) pseudo-ternary phase diagram. Under this framework, the roles played by the related approximants in the transition process are briefly discussed.     

Structure changes in Al80Ni15Y5 amorphous alloy

The structure of Al₈₀Ni₁₅Y₅ amorphous alloy at various temperatures have been studied with X-ray diffraction methods. The obtained scattered intensities, structure factors, pair correlation functions and main structure parameters have been analyzed. Temperature dependences of the parameters suggest formation of Al, Al₃Ni and Al₂₃Ni₆Y₄ phases upon crystallization of an amorphous alloy.     

Glass formation of Ti–Ni–Sn ternary alloys correlated with TiNi–Ti3Sn pseudo binary eutectics

Glass-forming ability (GFA) of Ti–Ni–Sn ternary alloys was investigated. Applying recent models based on atomic size ratio and efficient packing, the composition favoring the glass formation is predicted. Our experiments indicate that the optimized glass-forming composition is located at Ti₅₆Ni₃₈Sn₆, with the critical thickness of complete glass formation approaching 100 μm for the melt-spun ribbons. The Ti₅₆Ni₃₈Sn₆ metallic glass exhibits a sizable supercooled liquid region (ΔT_x) of about 35 K and a reduced glass transition temperature (T_rg) of 0.52. We demonstrate that the glass formation of the Ti₅₆Ni₃₈Sn₆ alloy correlates with the (L → TiNi + Ti₃Sn) pseudo binary eutectic reaction in Ti–Ni–Sn ternary system, which has an invariant temperature and composition at ～1370 K and ～Ti₅₈Ni₃₄Sn₈, respectively. With respect to Sn-free Ti–Ni binary alloys, the GFA is enhanced for the Ti–Ni–Sn ternary alloys, but the improvement is limited possibly due to changes in the crystalline phases competing with glass formation.     

Microstructural evolution of decagonal quasicrystal in the undercooled Al72Ni12Co16 alloy melts

The microstructure evolution of decagonal quasicrystals in Al₇₂Ni₁₂Co₁₆ alloy was investigated by the electromagnetic melting and cyclic superheating method. Single-phase decagonal quasicrystals have been obtained when the undercoolings were larger than 60 K. The decagonal quasicrystals formed at various undercoolings show different microstructural morphologies. Furthermore, grain refinement was found near the undercooling of 120 K. Based on current thermodynamic and dendrite growth theories, a dimensionless superheating parameter was adopted to explain the effect of processing conditions on the microstructure of Al₇₂Ni₁₂Co₁₆ alloy. The result indicate that the fine equiaxied microstructure of decagonal quasicrystal (D-phase) formed near on undercooling of 120 K originates from the break-up of dendrites.     

Investigation of glass forming ability in Ce–Al–Ni alloys

The compositional dependence of the glass forming ability (GFA), the correlation between their GFA and the GFA related parameters, and the thermal stability of the Ce–Al–Ni alloys were investigated. Rapidly quenched Ce₆₅Al_xNi_35 ? x (x = 2, 5, 10, 17, 20) and Ce₇₀Al_xNi_30 ? x (x = 2, 5, 10, 15, 20) ribbons were prepared by melt spinning, and their phase transformations were studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The experimental results indicated that the GFA of Ce₆₅Al_xNi_35 ? x (x = 2, 5, 10, 17, 20) and Ce₇₀Al_xNi_30 ? x (x = 2, 5, 10, 15, 20) alloys increased firstly and then decreased with the increasing of the Al content up to 20 at.%, respectively. It was found that only one parameter, F₁, in evaluated currently available empirical GFA parameters searching for metallic glasses with a good GFA, can reflect the GFA of the Ce–Al–Ni alloys. It was indicated that the thermal stability of alloy with fully amorphous maybe lower than that of alloy with partial amorphous.     

Complex crystallization mode of amorphous/nanocrystalline composite Al86Ni2Co5.8Gd5.7Si0.5

Kinetics of the first crystallization stage of Al₈₆Ni₂Co_5.8Gd_5.7Si_0.5 amorphous alloy and structure of the partially crystallized specimens were investigated by measurements of electrical resistance, X-ray diffraction and transmission electron microscopy. The presence of Al nanocrystals and eutectic colonies consisted of mutually oriented crystals of Al and metastable phase was found. The transient nucleation and slowing-down diffusion-limited growth and the interface-controlled growth of the quenched-in nuclei were identified as mechanisms of formation of the Al nanocrystals and eutectic colonies, respectively.     

Atomic structure and hydrogen storage properties of amorphous–quasicrystalline Zr–Cu–Ni–Al melt-spun ribbons

A structural state of the Zr–Cu–Ni–Al melt-spun ribbons has been investigated by means of X-ray diffraction analysis. It was established that conditions of ribbon production have a very strong effect on their structural state. The Zr_69.3Cu_9.7Ni_15.1Al_5.9 ribbons produced at the surface wheel velocity of 44 m/s have an amorphous state at the contact side and mixed amorphous–quasicrystalline state at the free side. At the same time the Zr_67.5Cu_12.5Ni₁₂Al₈ ribbons are fully amorphous in case of producing velocity of 44 m/s and have only small features of quasicrystalline peaks on the amorphous halo on the free side in case of producing velocity of 30 m/s in contrast to an amorphous structure on the contact side. The uncoated by Pd amorphous and amorphous–quasicrystalline Zr–Cu–Ni–Al ribbons have a property of absorbing a large amount of hydrogen. Parameters of the amorphous state were calculated for the ribbons as-prepared and hydrogenated. The temperature coefficient of resistivity for all ribbons is negative in range of 20–380 °C, what as well as the high resistivity values is typical to the Zr–Cu–Ni–Al based systems in amorphous and quasicrystalline states.     

Enthalpy recovery and its effect on homogeneous flow stress during supercooled liquid region for Ti40Zr25Ni8Cu9Be18 bulk metallic glass

The homogeneous flow exhibits strain softening for Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈ bulk metallic glass, which is related to increase in free volume concentration based on free volume model. When metallic glass is pre-annealed above T_g before deformation, the trend of strain softening becomes slow with pre-annealing time, indicating that the enthalpy recovery contributes to strain softening, because the enthalpy of metallic glass will recover towards equilibrium value above T_g, and leads to increase in free volume concentration. So the strain softening for Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈ bulk metallic glass is related to enthalpy recovery.     

The effect of TiO2 on phase separation and crystallization of glass-ceramics in CaO–MgO–Al2O3–SiO2–Na2O system

The experiments were carried out on studying the effect of phase separation on nucleation and crystallization in the glass based on the system of CaO–MgO–Al₂O₃–SiO₂–Na₂O. In the experiments, TiO₂ was chosen as nucleating agent. Three batches of 5, 8 and 10 wt% TiO₂ substitution were investigated by the techniques of DSC, XRD, FTIR and FESEM equipped with EDS. XRD and FTIR analysis indicated that the super cooled glasses were all amorphous, the heat treatment leading to nucleation would cause a disruption of silica network which followed phase separation. The phase separation followed the generation of crystal seeds Mg(Ti, Al)₂O₆. FESEM observation and EDS analysis revealed that the more TiO₂ content of glass, the more droplet separated phase and crystal seeds after nucleation heat treatment. The main crystal phase is clinopyroxene, Ca(Ti, Mg, Al)(Al, Si)O₆, of crystallized glass.     

Atomic dynamics and interatomic interaction in quasicrystals

The previous experimental data on the partial spectra of thermal atomic vibrations in icosahedral (Al₆₂Cu_25.5Fe_12.5) and decagonal (Al_71.3Ni₂₄Fe_4.7) quasicrystals have been used to perform a comparative analysis of the atomic dynamics features and determine the role that Al, Cu, Ni, and Fe atoms play in the formation of interatomic interaction in the alloys studied. A physical model of the decagonal quasicrystal structure is proposed.