Viscoelastic signature of physisorbed macromolecules at the solid-liquid interface

Viscoelastic behavior of a solution boundary layer at a solid-liquid interface could differ from that of bulk solution due to molecular adsorption at the interface. Such a property can be used as a characteristic signature to indicate the molecular adsorption at the interface. In this work, we systematically measured the viscoelastic properties of polyethylene glycol (PEG) solution boundary layers in contact with a gold surface using a quartz crystal resonator technique. The results show that viscosity and shear modulus of the PEG boundary layer increase with the PEG concentration in the solution; the increasing rate depends on the molecular weight. For relatively small PEG molecules, the viscoelastic property of the PEG solution boundary layer is almost indistinguishable from that of the bulk solution of the same concentration, indicating no adsorption at the interface. For larger PEG polymers (with molecular weights above a few thousands grams per mole), the viscoelastic property of the solution boundary layer differs distinctively from that of the corresponding bulk solution. The difference can be attributed to physisorption of PEG molecules on the Au surface, which alters the viscoelastic behaviors of the boundary layer. The results suggest that adsorption behaviors of macromolecules at a solid-liquid interface might be inferred from the changes of the viscoelastic properties of a solution boundary layer.     

A novel dual-impedance-analysis EQCM system--investigation of bovine serum albumin adsorption on gold and platinum electrode surfaces

Both quartz crystal micro-balance (QCM) impedance and electrochemical impedance spectroscopy (EIS) methods are widely used in interface studies. This paper presents details about a new strategy for simultaneous, mutual-interference-free and accurate measurements of QCM impedance and EI, through connecting a suitable capacitance in series with the piezoelectric quartz crystal (PQC) between QCM impedance and EIS measurement instruments. Combined and individual measurements of QCM impedance and EIS during silver deposition gave results comparable with each other, demonstrating the reliability of the proposed method. Bovine serum albumin (BSA) adsorption on gold and platinum electrodes in Britton-Robinson (B-R) buffers was investigated, and the Fe(CN)6(3-)/Fe(CN)6(4-) couple was used as an electrochemical probe to characterize BSA adsorption. While the reversibility of Fe(CN)6(3-)/Fe(CN)6(4-) couple on bare Au and Pt electrodes changed very slightly with decreasing solution pH from pH approximately 7 to pH approximately 2, the standard rate constant (ks) of this couple increased abruptly with solution pH below pH approximately 4.5 at a BSA-modified Au electrode, but decreased with solution pH at a BSA-modified Pt electrode. By analyzing the QCM impedance data with a modified BVD equivalent circuit and the EI data with a modified Randle's equivalent circuit, inflexion changes at pH approximately 4.5 were all found at pH-dependent responses of the resonant frequency, the double-layer capacitance, the capacitance of the adsorbed BSA layer, the peak-absorbance values of BSA solutions at 277.5 and 224.5 nm, and so on. It was also found that a BSA adsorption layer can effectively inhibit gold corrosion during ferrocyanide oxidation in a ferrocyanide-containing BR solution. Some preliminary explanations of these findings have been given. The proposed method is highly recommended for wider applications in surface science.     

放射标记法研究壳聚糖与牛血清白蛋白的自组装超薄膜

基片在两种带有相反电荷的聚电解质溶液中交替吸附 ,其表面形成致密有序的超薄膜的自组装 (ＥＳＡ ｅｌｅｃｔｒｏｓｔａｔｉｃｓｅｌｆ ａｓｓｅｍｂｌｙ)技术是由Ｄｅｃｈｅｒ及其合作者在 1 991年提出[1] ,由于简单易行 ,从一出现就受到了广大研究者的极大兴趣[2～ 4 ] .对生物材料来说 ,这无疑是一项非常重要且方便的表面改性手段 .因为生物材料在生物体内种植时 ,是否会被机体视为异物 ,关键在于机体与材料表面的相互作用 ,而与材料的本体性质基本无关[5] .因此利用这种技术 ,可对生物材料 ,特别是对那些生物相容性不好的材料表面进行…     

Analysis of photo-induced hydration of a photochromic poly(N-isopropylacrylamide) - Spiropyran copolymer thin layer by quartz crystal microbalance

We investigated hydration and swelling behavior of a solid state photoresponsive copolymer in water by using a quartz crystal microbalance technique with dissipation measurement (QCM-D technique). On the gold film electrode of a quartz resonator, we deposited a thin layer of a pNSp-NIPAAm, which is a poly(N-isopropylacrylamide) (pNIPAAm) polymer partially modified with a photochromic chromophore, 6-nitrospiropyran (NSp). Using QCM-D measurements, we found that at a temperature of 19 °C both water adsorption and changes in the viscoelasticity of the solid pNSp-NIPAAm layer were induced when pNSp-NIPAAm was irradiated by 365 nm ultraviolet light, which triggers the photoisomerization of the NSp chromophore and makes the structure of the chromophore hydrophilic. At temperatures between 25 and 35 °C, this photo-induced hydration was not observed. These observations suggest that the photoisomerization of the NSp chromophores triggered the photo-induced hydration only when pNIPAAm component is sufficiently hydrophilic, at a temperature of 19 °C.     

蛋白A定向固定抗体的纤维蛋白压电免疫传感器的研究

将9MHz双面镀金石英晶体浸入蛋白A溶液中,在晶体电极表面形成一层均匀的蛋白A薄层,用于定向固定人体纤维蛋白抗体.在蛋白A层上形成一层有序致密的自组装抗体分子膜,研制成一种新型的用于人体纤维蛋白检测的压电免疫传感器.比较了3种固定抗体方法的效果,从传感器的灵敏度、稳定性、重现性等考虑,蛋白A吸附法优于聚乙烯亚胺及牛血清白蛋白固定抗体的方法.研究了蛋白A浓度、抗体效价以及抗原抗体反应时间等对传感器灵敏度的影响,考察了电极的选择性和再生能力.纤维蛋白在1×10^-4～1×10^-2g/L浓度范围内有良好响应.     

电化学石英晶体微天平实时表征和定量检测短序列DNA

利用电化学石英晶体微天平(EQCM)这一灵敏的质量和电化学传感器测定特定序列DNA。应用自组装膜技术在压电石英晶振表面自组装一带羧基的α－硫辛酸单层膜,通过盐酸1-乙基-3-(3-二甲基氨基丙基)碳二亚胺(EDC)及N-羟基琥珀酰亚胺(NHS)共价固化寡聚核苷酸为探针,用于测定与其碱基序列互补的DNA。实验中EQCM实时监测了α-硫辛酸的自组装过程、探针固化过程及其与cDNA杂交过程。定量得出了探针固化量及cDNA杂交量。在酸性、中性和碱性条件下,分别对固化和杂交过程进行表征,实验发现探针固化及DNA杂交都受pH影响,本文对此现象进行了解释。同时,利用染料Hoechst33258的电化学活性,使其与双链DNA嵌合,通过测量Hoechst33258的电化学信息进一步验证了DNA杂交关键步骤。     

Protein adsorption on surfaces: dynamic contact-angle (DCA) and quartz-crystal microbalance (QCM) measurements

Adsorption of the protein bovine serum albumin (BSA) on gold has been tested at various concentrations in aqueous solution by dynamic contact-angle analysis (DCA) and quartz-crystal microbalance (QCM) measurements. With the Wilhelmy plate technique advancing and receding contact angles and the corresponding hysteresis were measured and correlated with the hydrophilicity and the homogeneity of the surface. With electrical admittance measurements of a gold-coated piezoelectrical quartz crystal, layer mass and viscoelastic contributions to the resonator's frequency shift during adsorption could be separated. A correlation was found between the adsorbed mass and the homogeneity and hydrophilicity of the adsorbed film.     

Bovine serum albumin adsorption on nano-rough platinum surfaces studied by QCM-D

The adsorption of bovine serum albumin (BSA) on platinum surfaces with a root-mean-square roughness ranging from 1.49nm to 4.62nm was investigated using quartz crystal microbalance with dissipation (QCM-D). Two different BSA concentrations, 50microg/ml and 1mg/ml, were used, and the adsorption studies were complemented by monitoring the antibody interaction with the adsorbed BSA layer. The adsorption process was significantly influenced by the surface nano-roughness, and it was observed that the surface mass density of the adsorbed BSA layer is enhanced in a non-trivial way with the surface roughness. From a close examination of the energy dissipation vs. frequency shift plot obtained by the QCM-D technique, it was additionally observed that the BSA adsorption on the roughest surface is subject to several distinct adsorption phases revealing the presence of structural changes facilitated by the nano-rough surface morphology during the adsorption process. These changes were in particular noticeable for the adsorption at the low (50microg/ml) BSA concentration. The results confirm that the nano-rough surface morphology has a significant influence on both the BSA mass uptake and the functionality of the resulting protein layer.     

QCM-D analysis of the performance of blocking agents on gold and polystyrene surfaces

With today's developments of biosensors and medical implants comes the need for efficient reduction of nonspecific binding. We report on a comparison of the ability of traditionally used blocking agents and poly(ethylene glycol) (PEG) derivatives to prevent protein adsorption on both gold and polystyrene surfaces. The adsorption kinetics of blocking molecules and proteins was monitored gravimetrically using quartz crystal microbalance with dissipation (QCM-D). The resistance to nonspecific adsorption was evaluated on gold and polystyrene surfaces coated with bovine serum albumin (BSA) or casein, gold coated with three different 6-11 ethylene glycol (EG) long hydroxyl- or methoxy-terminated PEG-thiolates and polystyrene blocked with a PLL-g-PEG or three different 12 EG long benzyl-PEG-derivatives. The prevention of protein adsorption on the coated surfaces was evaluated by monitoring the mass uptake at the addition of both pure prostate specific antigen (PSA) and seminal plasma. We demonstrate that on pure gold the PEG-thiols are superior to the other blocking molecules tested, with the end group and length of the PEG-thiols used being of minor importance. On polystyrene surfaces blocking with PLL-g-PEG, BSA and casein gave the best results. These results have an impact on further development of an optimized immunoassay protocol.     

牛血清白蛋白在超薄纳米二氧化钛膜表面的印迹与吸附

基于溶胶凝胶分子印迹方法,以溶胶二氧化钛TiO2为基质印迹了牛血清白蛋白分子。用1%的NaOH溶液可有效地除去纳米TiO2印迹膜中的模板分子。采用石英晶体微天平现场技术,研究了牛血清白蛋白在超薄纳米TiO2膜表面的吸附行为。研究表明,牛血清白蛋白在印迹膜和非印迹膜上的吸附量都随溶液浓度增加而增大,印迹膜具有吸附的特异性和可再生性,其吸附量是非印迹膜的3~5倍;在非印迹膜上的吸附符合Langmuir吸附模型,而在印迹膜上的吸附符合allosteric吸附模型;牛血清白蛋白在非印迹膜上的吸附量先随pH升高而增大,当pH为5左右时达到最大值,随后吸附量又随pH的增大而减小;而在印迹膜上其吸附量仅随pH增大而增大。     

Highly reproducible hybridization assay of zeptomole DNA based on adsorption of nanoparticle-bioconjugate

A nanoparticle-bioconjugate was formed by homogeneous hybridization of one polynucleotide target with two oligonucleotide probes labelled by thiol and a nanoparticle, respectively. Deposition of the nanoparticle-bioconjugate on a gold surface by thiol-gold reaction was monitored in situ by quartz crystal microbalance (QCM) and applied for flow analysis of zeptomole amounts of polynucleotide. The formation in solution and adsorption of thiolated conjugates on gold could be fast, uniform and effective, and has been successfully exploited to construct a highly reproducible and sensitive platform for detection of target sequences. Being more rapid, reproducible, sensitive and amenable to automation than previously reported microgravimetric hybridization assays, this technology has great promise for practical applications in molecular diagnostics.     

耗散型石英晶体微天平在生物医用高分子材料中的应用

石英晶体微天平(QCM)是一种基于石英晶体压电效应的分析检测技术,可实时在线提供石英晶体表面吸附层质量、厚度、粘弹性等信息,由此获得表面分子相互作用关系。 耗散型石英晶体微天平(QCM-D)因其独特的对粘弹性的解析,使其在高分子材料中的应用迅速发展,尤其是生物医用高分子材料领域,已用来评价生物医用高分子材料的表界面相互作用,力学和生物相容性等。 本文简单介绍了耗散型石英晶体微天平的基本原理及理论模型,重点综述了近几年QCM-D在高分子链构象、蛋白质吸附、生物大分子相互作用、药物释放以及水凝胶中的应用,并且展望了QCM-D的未来发展趋势。     

QCM/HCC as a platform for detecting the binding of warfarin to an immobilized film of human serum albumin

Quartz crystal microbalance/heat conduction calorimetry (QCM/HCC) is a new measurement technology that has been used to monitor simultaneously the mass and motional resistance of a thin film in conjunction with the heat flow produced by a chemical change in the film initiated by reaction with a gas. In this work we examine the applicability of the QCM/HCC in detecting chemical changes at the solution/thin film interface. Human serum albumin (HSA) was bound to the gold electrode of a 5 MHz AT-cut quartz resonator using three types of linkers and then exposed to buffered solutions of the anticoagulant drug warfarin. Changes in resonator frequency and motional resistance as well as changes in heat flow produced by warfarin binding to HSA were monitored as a function of the warfarin concentration. Differences in frequency and motional resistance changes depend upon the linker and vary both in magnitude and sign, whereas the integrated heat signal is proportional to the concentration of warfarin and independent of the linker chemistry. Quartz crystal microbalance/heat conduction calorimetry can thus be a useful tool for studying protein-ligand interactions at the solution-surface interface, even though the quartz resonator does not behave as a microbalance.     

Adsorption and viscoelastic properties of fractionated mucin (BSM) and bovine serum albumin (BSA) studied with quartz crystal microbalance (QCM-D)

The adsorption profile and viscoelastic properties of bovine submaxillary gland mucin (BSM) and bovine serum albumin (BSA), extracted from a commercial mucin preparation, adsorbing to polystyrene surfaces has been studied using quartz crystal microbalance with dissipation monitoring (QCM-D). A significant difference in the adsorption properties of the different proteins was detected; with the BSA adsorbing in a flat rigid layer whilst the mucin adsorbed in a diffuse, highly viscoelastic layer. Subsequent addition of BSA to the preadsorbed mucin layer resulted in stiffening of the protein layer which was attributed to complexation of the mucin by BSA. In contrast, a preadsorbed layer of BSA prevented mucin adsorption altogether. Combined mixtures of mucin and BSA in well defined ratios revealed intermediate properties between the two separate protein species which varied systematically with the protein ratios. The results shed light on the synergistic effects of complexation of lower molecular weight biomolecular species with mucin. The possibility to selectively control protein uptake and tailor the physical properties of the adsorbed layer makes mucin an attractive option for application in biomaterial coatings.     

Real-time monitoring of stain formation and removal on calcium hydroxyapatite surfaces using quartz crystal sensor technology

Stain formation, stain inhibition and stain removal may be monitored in real-time using a novel method employing a quartz crystal resonance sensor (QCR), based upon quartz crystal microbalance (QCM) technologies. Crystalline hydroxyapatite (HA) surfaces were prepared on phosphate-terminated, polymer-modified gold surfaces of quartz crystal transducers. The resulting sensors were placed in a specially constructed flow cell, and the interaction of adsorbates from the tea stain solution monitored as a function of time. The ability of sodium tripolyphosphate (STP) to remove extrinsic stain and also to inhibit its formation was examined. The adsorption of material from the staining solution passed over the sensor was clearly observable, and once bound, the crystal based real-time data suggest that tea adsorbates were not removed in the absence of an active under conditions of continuous flow. STP was shown to rapidly remove existing stain, and exhibited a clear inhibitory action on stain formation irrespective of whether the HA had been previously exposed to tea chromogens. The continuous data generated by the QCR technique were in good agreement with the results obtained using a discontinuous spectrophotometric method. The presently described quartz crystal model for extrinsic dental stain should provide a valuable tool to aid understanding of the interactions of staining agents with a crystalline HA surface as a model tooth surface, and to evaluate the efficacy and mode of action of STP and putative stain removal agents.     

Electrochemical quartz crystal microbalance study of azurin adsorption onto an alkanethiol self-assembled monolayer on gold

A quartz crystal microbalance coupled with electrochemistry was used to examine the adsorption of azurin on a gold electrode modified with a self-assembled monolayer of octanethiol. Azurin adsorbed irreversibly to form a densely packed monolayer. The rate of azurin adsorption was related to the bulk concentration of azurin in solution within the concentration range studied. At a high azurin concentration (2.75 muM), adsorption was rapid with a stable adsorption maximum attained in 2-3 min. At a lower azurin solution concentration (0.35 muM), the time to reach a stable adsorption maximum was approximately 30 min. Interestingly, the maximum surface concentration attained for all solution concentrations studied by the QCM method was 25 +/- 1 pmol cm-2, close to that predicted for monolayer coverage. The dissipation was monitored during adsorption, and only small changes were detected, implying a rigid adsorption model, as needed when using the Sauerbrey equation. Cyclic voltammetric data were consistent with a one-electron, surface-confined CuII/CuI azurin process with fast electron-transfer kinetics. The electroactive surface concentration calculated using voltammetry was 7 +/- 1 pmol cm-2. The differences between the QCM and voltammetrically determined surface coverage values reflect, predominantly, the different measurement methods but imply that all surface-confined azurin is not electrochemically active on the time scale of cyclic voltammetry.     

A quartz crystal microbalance study of the adsorption of asphaltenes and resins onto a hydrophilic surface

The adsorption of extracted and purified samples of asphaltenes and resins onto gold surfaces has been studied as a function of bulk concentration using a quartz crystal microbalance with dissipation measurements (QCM-D). With this device, which works equally well in transparent, opaque, and nontransparent samples, the adsorbed amount is measured through a change in resonant frequency of the quartz oscillator. The measured change in dissipation reports on changes in layer viscoelasticity and slip of the solvent at the surface. The results show that the adsorbed amount for resins from heptane corresponds to a rigidly attached monolayer. The adsorbed amount decreases with increasing amount of toluene in the solvent and is virtually zero in pure toluene. Asphaltenes, on the other hand, adsorb in large quantities and the mass and dissipation data demonstrate the presence of aggregates on the surface. The aggregates are firmly attached and cannot be removed by addition of resins. On the other hand, resins and asphaltenes associate in bulk liquid and the adsorption from mixtures containing both resins and asphaltenes is markedly different from that obtained from the pure components. Hence, we conclude that preformed resin aggregates adsorb to the surface. These results are compared and discussed in relation to adsorption from crude oil diluted in heptane/toluene mixtures.     

Probing protein adsorption onto mercaptoundecanoic acid stabilized gold nanoparticles and surfaces by quartz crystal microbalance and zeta-potential measurements

The adsorption characteristics of three proteins [bovine serum albumin (BSA), myoglobin (Mb), and cytochrome c (CytC)] onto self-assembled monolayers of mercaptoundecanoic acid (MUA) on both gold nanoparticles (AuNP) and gold surfaces (Au) are described. The combination of quartz crystal microbalance measurements with dissipation (QCM-D) and pH titrations of the zeta-potential provide information on layer structure, surface coverage, and potential. All three proteins formed adsorption layers consisting of an irreversibly adsorbed fraction and a reversibly adsorbed fraction. BSA showed the highest affinity for the MUA/Au, forming an irreversibly adsorbed rigid monolayer with a side-down orientation and packing close to that expected in the jamming limit. In addition, BSA showed a large change in the adsorbed mass due to reversibly bound protein. The data indicate that the irreversibly adsorbed fraction of CytC is a monolayer structure, whereas the irreversibly adsorbed Mb is present in form of a bilayer. The observation of stable BSA complexes on MUA/AuNPs at the isoelectric point by zeta-potential measurements demonstrates that BSA can sterically stabilize MUA/AuNP. On the other hand, MUA/AuNP coated with either Mb or CytC formed a reversible flocculated state at the isoelectric point. The colloidal stability differences may be correlated with weaker binding in the reversibly bound overlayer in the case of Mb and CytC as compared to BSA.     

Fibronectin and bovine serum albumin adsorption and conformational dynamics on inherently conducting polymers: a QCM-D study

Quartz crystal microbalance with dissipation monitoring (QCM-D) was employed to characterize the adsorption of the model proteins, bovine serum albumin (BSA) and fibronectin (FN), to polypyrrole doped with dextran sulfate (PPy-DS) as a function of DS loading and surface roughness. BSA adsorption was greater on surfaces of increased roughness and was above what could be explained by the increase in surface area alone. Furthermore, the additional mass adsorbed on the rough films was concomitant with an increase in the rigidity of the protein layer. Analysis of the dynamic viscoelastic properties of the protein adlayer reveal BSA adsorption on the rough films occurs in two phases: (1) arrival and initial adsorption of protein to the polymer surface and (2) postadsorption molecular rearrangement to a more dehydrated and compact conformation that facilitates further recruitment of protein to the polymer interface, likely forming a multilayer. In contrast, FN adsorption was independent of surface roughness. However, films prepared from solutions containing the highest concentration of DS (20 mg/mL) demonstrated both an increase in adsorbed mass and adlayer viscoelasticity. This is attributed to the higher DS loading in the conducting polymer film resulting in presentation of a more hydrated molecular structure indicative of a more unfolded and bioactive conformation. Modulating the redox state of the PPy-DS polymers was shown to modify both the adsorbed mass and viscoelastic nature of FN adlayers. An oxidizing potential increased both the total adsorbed mass and the adlayer viscoelasticity. Our findings demonstrate that modification of polymer physicochemical and redox condition alters the nature of protein-polymer interaction, a process that may be exploited to tailor the bioactivity of protein through which interactions with cells and tissues may be controlled.     

Viscoelasticity in the diffuse electric double layer

The electroacoustical impedance of the quartz crystal microbalance (QCM) in contact with aqueous electrolyte solutions was measured using the transfer function method in a flow injection system . Measurements of both components of the impedance of the QCM, the resistance R and the inductive reactance XL, have been performed for modified and bare gold and silver surfaces and for different concentrations of several aqueous electrolyte solutions. For the experimental concentration range of 0-50 mM, unexpectedly the QCM impedance does not follow the Kanazawa equation, as is usual for bulk newtonian liquids. This behavior indicates the presence of a nanometric sized viscoelastic layer between the piezoelectric crystal and the bulk electrolyte solution. This layer can only be identified as the Gouy-Chapman diffuse double layer (DDL). Its elasticity and viscosity have been estimated by the measurement of R and XL. The viscoelasticity of the DDL appears to be independent of the chemical nature of the surface and of the solution viscosity but strongly dependent on the surface charge, the bulk electrolyte concentration and the dielectric constant of the solvent.