Structural transformation of fluorinated carbon nanotubes induced by in situ electron-beam irradiation

We have investigated the structural transformation of fluorinated singlewalled nanotubes (SWNTs) induced by electron-beam irradiation during the transmission electron microscope observations. Heavily fluorinated SWNT bundles were systematically transformed into multiwall-like nanotubes by releasing fluorine atoms during electron-beam irradiation and even broken into two pieces of the capped graphitic structures. Such structural transformations at relatively low kinetic energy (< or = 300 keV) could be explained by the local strains induced by fluorination, where C-C bonds that were fluorine-attached became 1.53 A, a single bond similar to that of a diamond, from our density functional calculations. We propose a possible concerted pathway for the structural transformation of fluorinated SWNTs induced by electron-beam irradiation based on the experimental observations.     

A viable way to tailor carbon nanomaterials by irradiation-induced transformations

Since the discovery of carbon nanotubes (CNT), transmission electron microscopy (TEM) has been the most important tool in their investigation. It is possible to use electron irradiation in a TEM to construct a single-walled carbon nanotube (SWCNT) from an amorphous carbon film. Here we show that such a synthesis method creates a large number of carbon ad-atoms, which after some critical amount of radiation act to restore the system by reconstructing the carbon film. The behavior of the ad-atoms can be controlled by adjusting the current density in the microscope, suggesting that carbon nanomaterials can be tailored by electron irradiation.     

Single-walled carbon nanotubes for improved enantioseparations on a chiral ionic liquid stationary phase in GC

In order to investigate whether the use of single-walled carbon nanotubes can improve enantioseparations on an ionic liquid stationary phase, a chiral ionic liquid, (R)-N,N,N-trimethyl-2-aminobutanol-bis(trifluoromethanesulfon)imidate, was synthesized. Two capillary columns, one containing the chiral ionic liquid and the other containing the single-walled carbon nanotubes and the chiral ionic liquid, were then prepared for GC. The results of the separations achieved with these columns show that coating the chiral ionic liquid stationary phase onto the capillary column containing single-walled carbon nanotubes improves the enantioselectivety of the chiral ionic liquid. This work indicates that using single-walled carbon nanotubes in this manner enables the application range of such GC chiral separations to be extended.     

SiOx纳米管的制备及其发光特性

Amorphous SiOx nanotubes with homogeneous diameters were fabricated in large-scale on silicon substrate by thermal evaporation method, with liquid gallium as medium. The average diameter of tubes is about 80 nm and the length is more than 10 1m, with small ratio between the inner and outer diameter of the tube. The silicon element in the substrate and the residual oxygen element in reaction chamber were first dissolved into liquid Ga. Then the SiOx precipitated from the surface of gallium droplet, forming the nanotube structure with Ga droplet being the center. The room temperature photoluminescence measurements under excitation at 260 nm show that the SiOx nanotubes has a strong blue emission at 453 nm with two shoulders at 410 and 480 nm respectively, which may be related to oxygen defects. The preparation method improved the traditional complicated method and also provided a new way to fabricate SiOx nanotubes in large quantity.     

Selective intercalation of polymers in carbon nanotubes

A room-temperature, open-air method is devised to selectively intercalate relatively low-molecular-weight polymers (approximately 10-100 kDa) from dilute, volatile solutions into open-end, as-grown, wettable carbon nanotubes with 50-100 nm diameters. The method relies on a novel self-sustained diffusion mechanism driving polymers from dilute volatile solutions into carbon nanotubes and concentrating them there. Relatively low-molecular-weight polymers, such as poly(ethylene oxide) (PEO, 600 kDa) and poly(caprolactone) (PCL, 80 kDa), were encapsulated in graphitic nanotubes as confirmed by transmission electron microscopy, which revealed morphologies characteristic of mixtures in nanoconfinements affected by intermolecular forces. Whereas relatively small, flexible polymer molecules can conform to enter these nanotubes, larger macromolecules (approximately 1000 kDa) remain outside. The selective nature of this process is useful for filling nanotubes with polymers and could also be valuable in capping nanotubes.     

The radiation degradation of a nanotube-polyimide nanocomposite

The radiation degradation of a nanotube-polyimide nanocomposite was studied. Radiation chemistry was observed that was not present in the unmodified polymer or in the imbedded single-walled carbon nanotubes (SWNTs) themselves. The tensile properties were found to be improved by the addition of SWNTs in the unirradiated materials, and no deterioration in these properties with irradiation was observed. The SWNTs were found to have a detrimental effect on the optical properties however. The transparency of the composite was degraded significantly faster by electron-beam radiation than the neat polymer was. This may make the SWNT/polyimide composites unsuitable for some space applications. Electron Spin Resonance (ESR) measurements determined that the SWNTs interfere with the radical chemistry in the irradiated materials. This could be due to energy dissipation by the SWNT network, preventing the formation of radical species, or alternatively, preferential reaction or termination of radicals by the nanotubes. FT-Raman spectroscopy was found to be a very useful tool for examining SWNTs embedded at low concentrations. It revealed no signs of SWNT degradation up to 10 MGy.     

Synthesis and characterization of ultrahigh crystalline TiO2 nanotubes

Ultrahigh crystalline TiO2 nanotubes were synthesized by hydrogen peroxide treatment of very low crystalline titania nanotubes (TiNT-as prepared), which were prepared with synthesized TiO2 nanoparticles by hydrothermal methods in an aqueous NaOH solution. Thus, prepared ultrahigh crystalline TiO2 nanotubes (TiNT-H2O2) showed comparable crystallinity with high crystalline TiO2 nanoparticles. The details of nanotubular structures were elucidated by high resolution-transmission electron microscopy (HR-TEM), field emission-scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis in transmission electron microscopy (TEM-EDX), X-ray diffraction (XRD), photoluminescence (PL), and BET surface area. TiNT-H2O2 was found to be a multiwalled anatase phase only with an average outer diameter of approximately 8 nm and an inner diameter of approximately 5 nm and grown along the [001] direction to 500-700 nm long with an interlayer fringe distance of ca. 0.78 nm. The photocatalytic activity of TiNT-H2O2 was about 2-fold higher than those of TiNT-as prepared, synthesized TiO2 nanoparticles, and TiO2-P25 (Degussa) in the photocatalytic oxidation of trimethylamine gas under UV irradiation.     

Carbon nanotube based stationary phases for microchip chromatography

The objective of this article is to provide an overview and critical evaluation of the use of carbon nanotubes and related carbon-based nanomaterials for microchip chromatography. The unique properties of carbon nanotubes, such as a very high surface area and intriguing adsorptive behaviour, have already been demonstrated in more classical formats, for improved separation performance in gas and liquid chromatography, and for unique applications in solid phase extraction. Carbon nanotubes are now also entering the field of microfluidics, where there is a large potential to be able to provide integrated, tailor-made nanotube columns by means of catalytic growth of the nanotubes inside the fluidic channels. An evaluation of the different implementations of carbon nanotubes and related carbon-based nanomaterials for microfluidic chromatography devices is given in terms of separation performance and ease of fabrication.     

Bulk synthesis of linear carbon chains confined inside single-wall carbon nanotubes by vacuum discharge

Carbyne, an infinite carbon chain, has attracted much interest and induced significant controversy for many decades. Recently, the presence of linear carbon chains (LCCs), which were confined stably inside double-wall carbon nanotubes (DWCNTs) and multiwall carbon nanotubes (MWCNTs), has been reported. In this study, we present a novel method to produce LCCs in a film of carbon nanotubes (CNTs). Our transmission electron microscopy and Raman spectroscopy revealed the formation of a bulk amount of LCCs after electric discharge of CNT films, which were used as field emission cathodes. The LCCs were confined inside single-wall CNTs as well as DWCNTs. Furthermore, two or three LCCs in parallel with each other are encapsulated when the inner diameter of CNT is larger than approximately 1.1 nm.     

Effect of Irradiation with a Continuous Beam of Accelerated Electrons on the Texture and Nanostructure of Carbon Black: a Study by Adsorption and High-Resolution Transmission Electron Microscopy

Textural, structural, and morphological changes occurring in globular carbon black of various particle size fractions under continuous irradiation with a continuous beam of 2.5-MeV accelerated electrons were studied by the methods of adsorption and high-resolution transmission electron microscopy. The electron irradiation leads to pronounced transformation of the solid globular framework of carbon black mainly into graphite-like nanocapsules of 10–50 nm size with the spacing between the graphene layers of the order of 0.355 nm. The observed effect leads to a decrease in the porosity (by a factor of approximately 1.65) and in the specific surface area (by a factor of 3–4) of the irradiated samples. This may be due to the transformation of the turbostratic (practically amorphous) form of carbon black into the nanostructured state with denser packing of carbon particles. The physicochemical properties of such carbon should be primarily determined by the structure of the solid framework.     

Carbon nanotube assisted synthesis of CeO2 nanotubes

CeO₂ nanotubes have been synthesized facilely using carbon nanotubes (CNTs) as templates by a liquid phase deposition method. The properties of the CeO₂ nanotubes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectrum (XPS) as well as thermogravimetry and differential thermal analysis (TG-DTA). The obtained CeO₂ nanotubes with a polycrystalline face-centered cubic phase have a uniform diameter ranging from 40 to 50 nm. The CeO₂ nanotubes are composed of many tiny interconnected nanocrystallites of about 10 nm in size. The pretreatment of CNTs and calcination temperature were confirmed to be the crucial factors determining the formation of CeO₂ nanotubes. A possible formation mechanism has been suggested to explain the formation of CeO₂ nanotubes.     

Generation of hydrophilic, bamboo-shaped multiwalled carbon nanotubes by solid-state pyrolysis and its electrochemical studies

A simple, efficient, and novel method was developed for the direct preparation of hydrophilic, bamboo-shaped carbon nanotubes by the pyrolysis of ruthenium(III) acetylacetonate in a Swagelock cell is reported. The obtained product exhibits mostly bamboo-shaped, straight, periodic twisted, multiwalled carbon nanotubes possessing diameters of 50-80 nm and lengths of around 10 microm. The pyrolyzed product was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution TEM (HRTEM), Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), micro-Raman, and cyclic voltammetric techniques. HRTEM studies showed that the walls of bamboo-shaped carbon nanotubes consisted of oblique grapheme planes with respect to the tube axis. The interlayer spacing between two graphitic layers was found to be 0.342 nm. XPS measurements have suggested that as-prepared carbon nanotubes consist the surface functional groups on the surface of carbon nanotubes. The electrochemical properties of synthesized carbon nanotubes have been evaluated. Thermogravimetric analysis (TGA), IR, and cyclic voltammetric studies showed the presence of oxygen functionalities. Raman studies revealed the presence of disorder in the graphitic carbon and the presence of exposed edge plane defects in the generated carbon nanotubes for influencing the surface behavior and electrochemical properties. The electrochemical behavior of electrodes made of bamboo-shaped carbon nanotubes served for an oxygen reduction reaction.     

Laser-induced pinpoint hydrogen evolution from benzene and water using metal free single-walled carbon nanotubes with high quantum yields

Metal-free photocatalytic hydrogen evolution occurred efficiently in benzene containing single-walled carbon nanotubes under laser irradiation at 532 nm with an extremely high turnover number of 2 000 000 and a high quantum yield of 130%. The rate of hydrogen evolution increased with increasing laser intensity to exhibit a fourth power dependence, suggesting that hydrogen was evolved via four-photon processes in which the coupling of two radical anions derived from benzene is the rate-determining step and the benzene radical anion is produced by electron transfer from benzene to the doubly excited state of single-walled carbon nanotubes, which requires two photons. Polymerisation of benzene was induced by the photogenerated C₆H₆˙^–, accompanied by hydrogen evolution, resulting in a leverage effect to increase the quantum yield of hydrogen evolution to well over the 25% expected for the four-photon process. Laser-induced hydrogen evolution also occurred in water containing single-walled carbon nanotubes. In contrast to the case of benzene, water was not oxidized but hydrogen evolution from water was accompanied by the multi-oxidation of single-walled carbon nanotubes. The yield of hydrogen based on one mole of single-walled carbon nanotubes with 1.4 nm diameter and 1–5 mm length was determined to be 2 700 000%, when oxidations of single-walled carbon nanotubes occurred to produce the polyhydroxylated product.     

Diameter dependence of low-energy electron and photon irradiation damage in single-walled carbon nanotubes

Low-energy photon irradiation in an ultra-high vacuum, as well as low-energy electron irradiation, was found to damage single-walled carbon nanotubes, meaning that electronic excitations are solely responsible for the defect formation. The formation and healing of the defects were found to strongly depend on nanotube diameter; that is, thinner nanotubes are more easily damaged and hardly recovered. The results mean that the irradiation damage is prominent in a rolled up graphene sheet, but not in a planar one. The curvature-induced strain energy seems to be essentially important for the damage.     

Selective photochemical functionalization of surfactant-dispersed single wall carbon nanotubes in water

Ultraviolet (UV) irradiation of single wall carbon nanotubes (SWCNTs) individually dispersed in surfactants leads to diameter and type-selective photohydroxylation of the nanotubes. Photohydroxylation of first semiconductor and then small diameter metallic SWCNTs was confirmed after 254 nm UV irradiation in acidic, neutral, and basic aqueous solutions at ambient and elevated temperatures. The increased oxygen content of the SWCNTs after UV irradiation, as detected by X-ray photoelectron spectroscopy, suggests that SWCNTs were hydroxylated by reaction with water. Attenuated total reflectance Fourier transform infrared analysis provides evidence of hydroxyl functional groups on their surface. This photochemical reaction is impeded by molecular oxygen and appears to involve a reactive intermediate generated in the vicinity of semiconducting SWCNTs. This represents a noncontaminating selective reaction in the liquid phase that uses an intrinsic property of the tubes.     

Polymer crystallization-driven, periodic patterning on carbon nanotubes

We report herein a unique means to periodically pattern polymeric materials on individual carbon nanotubes (CNTs) using a controlled polymer crystallization method. One-dimensional (1D) CNTs were periodically decorated with polymer lamellar crystals, resulting in nano-hybrid shish-kebab (NHSK) structures. The periodicity of the polymer lamellae varies from 20 to 150 nm. The kebabs are approximately 5-10 nm thick (along CNT direction) with a lateral size of approximately 20 nm to micrometers, which can be readily controlled by varying crystallization conditions. Both polyethylene and Nylon 66 were successfully decorated on single-walled carbon nanotubes (SWNTs), multiwalled carbon nanotubes (MWNTs), as well as vapor grown carbon nanofibers (CNFs). The formation mechanism was attributed to "size-dependent soft epitaxy". Because NHSK formation conditions depend on CNT structures, it further provides a unique opportunity for CNT separation. The reported method opens a gateway to periodically patterning polymers and different functional groups on individual CNTs in an ordered and controlled manner, an attractive research field that is yet to be explored.     

Amino-functionalized monolithic spin-type columns for high-throughput lectin affinity chromatography of glycoproteins

Hydrophilic poly(ethylene glycol)-based monoliths were synthesized in the spin-tip format for high-throughput applications via pulsed electron beam irradiation. Monoliths with a homogeneous porous structure and a total porosity of 69% were obtained. The cross-linked polymeric structure was further mechanically stabilized via the incorporation of silica nanoparticles. Amino-functionalization of the monoliths was accomplished by a straightforward, water-based, one-step approach that entailed the electron-beam irradiation-induced grafting of poly(allylamine). The amine functionalized spin columns showed very low unspecific protein adsorption and were successfully applied as adsorbents in lectin affinity chromatography for the purification of ovalbumin. The novel columns also outperformed a commercially available system.     

Synthesis and characterizations of amorphous carbon nanotubes by pyrolysis of ferrocene confined within AAM templates

Amorphous carbon nanotubes (a-CNTs) are synthesized by pyrolysis of ferrocene confined in the nanopores of the anodic alumina membrane (AAM) and characterized by field emission scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), electron energy-loss spectroscopy (EELS), and Raman spectroscopy. It is shown that the a-CNT has an ultrathin amorphous wall (approximately 3 nm) and a relatively large diameter (approximately 50 nm), and is capsulated with iron oxide nanoparticles. It is found that the growth of the a-CNTs is governed mainly by the template limitation effect. Electrical transport measurements on individual a-CNTs demonstrate that the a-CNT may be connected with electrodes via either ohmic or Schottky contacts, and the resisitivity of the a-CNTs was measured to be 4.5 x 10(-3) Omega cm.     

Effects of non-additive conductivity variation for a nematic liquid crystal caused by magnetite and carbon nanotubes at various scales

Effect of magnetite and single-walled carbon nanotubes (CNTs) on the electric conductivity of 6CHBT nematic liquid crystal (LC) dispersed in polyvinyl alcohol is studied. The chosen technology of mixture homogeneising is shown to result in a LC dispersed in a polymer matrix (PDLC) with average LC droplet size of 500 nm (nano-PDLC). The conductivity of the nano-PDLC films with simultaneously introduced magnetite and nanotubes is shown to be smaller than the sum of the conductivities of films with nanoparticles of each type introduced separately. The main reason for this effect is assumed to be the formation of deep electron trap levels from complexes of nanoparticles of different type and thereby a decrease of the electron conductivity across the polymer which is the main mechanism of charge transfer in nano-PDLC. The effect of magnetite and the CNTs on the conductivity of the homogeneous LC and the micro-PDLC is analysed in comparison with the nano-PDLC.     

Synthesis of straight and helical carbon nanotubes from catalytic pyrolysis of polyethylene

Straight and helical carbon nanotubes with diameter from 20 to 60 nm have been synthesized through catalytic decomposition of polyethylene in autoclave at 700 °C. The X-ray power diffraction pattern indicates that the products are hexagonal graphite, and transmission electron microscope (TEM) and high resolution transmission electron microscope (HRTEM) images reveal the morphologies and structures of carbon nanotubes. The effects of reaction temperature, catalyst and maleated polypropylene on the growth of the carbon nanotubes were also discussed, and the growth mechanism of the CNTs was proposed. Pyrolysis of polyethylene is a promising green chemical method for economically producing carbon nanotubes.