The improved photocatalytic properties of P-type NiO loaded porous TiO2 sheets prepared via freeze tape-casting

For the interest of the practical application, porous TiO₂ sheets were prepared by a novel freeze tape-casting method, in order to improve the photocatalytic activities of these TiO₂ sheets, p-type NiO was loaded by chemical solution deposition. The samples were characterized by a series of physical means, including XRD, SEM, EDS, XPS, ICP-OES, and UV-vis spectroscopy. The photocatalytic activities of the samples were evaluated by the degradation of methyl orange solution. The results showed that the photocatalytic activity of the TiO₂ sheet was greatly enhanced by the NiO loading, and the photocatalytic efficiency increased with increasing the NiO loading, the extraordinary performance for the NiO-loaded sample with 0.1 M precursor dipped was related to its unique morphology. The sample annealed at 600 °C showed the better photocatalytic activity than the sample annealed at 400 °C and 800 °C. The improvement of the photocatalytic activity was attributed to the formation of p–n junctures at the interface of the NiO/TiO₂, which facilitates the photoinduced electron/hole pairs' separation by the inner electric field, thus leading to the higher photocatalytic activities for the NiO-loaded TiO₂ sheets.     

Remediation of Wastewater with Ultraviolet Irradiation Using a Novel Titanium (IV) Oxide Photocatalyst

Photocatalysis has become common and nanomaterials having photocatalytic functions have been widely characterized. At present, among the many candidates for photocatalysis, TiO₂ is almost the only material suitable for industrial use. In this paper, we present a TiO₂ synthesis starting from Ti sheets put in contact with a mixture of 0.1 N NaOH and acetone for 72?hours under ambient conditions. The obtained sheets were washed with distilled water and ethanol, and the surface was analyzed for its structural and morphological properties. Thus, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) investigations indicated the formation of TiO₂ on the edges of nanometer circles on the surface of the Ti sheets. For characterizing the photocatalytic capacity for wastewater treatment, Ti sheets with TiO₂ on the surface contacted with methylene blue solutions at room temperature under ultraviolet light. The degradation of the methylene blue concentration was measured by ultraviolet–visible spectroscopy, demonstrating 99.94% efficiency for wastewater treatment using the obtained material.     

Au/TiO<Subscript>2</Subscript>/Graphene Composite with Enhanced Photocatalytic Activity Under Both UV and Visible Light Irradiation

Au/TiO₂/graphene composite was synthesized by the combination of electrostatic attraction and photo-reduction method. In the composite, graphene sheets act as an adsorption site for dye molecules to provide a high concentration of dye near to the TiO₂ and Au nanoparticles (NPs), and work as an excellent electron transporter to separate photoinduced e ^?/h ⁺ pairs. Under UV irradiation, photogenerated electrons of TiO₂ are transferred effectively to Au NPs and graphene sheets, respectively, retarding the recombination of electron–hole pairs. Under visible light irradiation, the Au NPs are photo-excited due to the surface plasmon resonance effect, and charge separation is accomplished by the interfacial electron injection from the Au NPs to the conduction band of TiO₂ and then transfer further to graphene sheets. As a result, compared with pure TiO₂, Au/TiO₂/graphene composite exhibited much higher photocatalytic activity for degradation of methylene blue under both UV and visible light irradiation, based on the synergistic effect of Au, graphene in contact with TiO₂, allowing response to the visible light, effective separation of photoinduced charges, and better adsorption of the dye molecules.     

静电纺丝技术制备TiO2@SiO2亚微米同轴电缆与表征

用静电纺丝技术成功制备出大量的TiO₂＠SiO₂亚微米同轴电缆. 用TGA-DTA, XRD, SEM, TEM, EDS, FTIR分析技术对样品结构和组成进行了系统的表征. 结果表明, 得到的产物为TiO₂＠SiO₂亚微米级同轴电缆, 以无定型SiO₂为壳层, 晶态TiO₂为芯层, 电缆平均直径450 nm, 壳层厚度90 nm, 电缆长度＞300 μm, 同时在样品中发现个别纤维呈现管状结构, 对其形成机理进行了讨论.     

低温静电自组装法制备贵金属修饰TiO_2纳米结构薄膜及其增强的光催化性能(英文)

以碱-水热法在金属Ti片上原位生长了TiO2纳米结构(纳米花和纳米线)薄膜,并采用低温静电自组装方法将超细贵金属(金、铂、钯)纳米颗粒均匀沉积于多孔TiO2薄膜上.负载于Ti片上的贵金属/TiO2纳米结构薄膜具有一体化结构、多孔架构和高光催化活性.超高分辨率场发射扫描电子显微镜(FESEM)直接观察表明贵金属纳米颗粒在TiO2表面分布均匀,且颗粒之间相互分离,金、铂、钯纳米颗粒的平均粒径分别约为4.0、2.0和10.0nm.俄歇电子能谱(AES)纵深成分分析表明贵金属不仅沉积于薄膜表面,且大量分布于TiO2纳米结构薄膜内部,其深度超过580 nm.X射线光电子能谱(XPS)分析表明,经300°C下在空气中热处理后,纳米金仍保持金属态,纳米铂部分被氧化成PtOabs,而钯粒子则完全被氧化成氧化钯(PdO).以低温静电自组装法沉积贵金属,贵金属负载量可通过调节组装时间与溶胶pH值来控制.光催化降解甲基橙的结果表明,沉积的纳米金和铂能显著增加TiO2纳米结构薄膜的光催化活性,说明金和铂粒子可促进光生载流子的分离;但负载的PdO对TiO2薄膜的光催化性能增强几乎无作用.     

Influence of N sources on the photocatalytic activity of N-doped TiO2

Influence of nitrogen precursors urea, semicarbazide and N,N’-dimethyl urea on the photocatalytic activity of the N-doped TiO₂ were studied by a simple decomposition method. The nano N-TiO₂ catalysts were synthesized via two different modified approaches by calcination at 500 °C. The synthesized samples were characterized by IR, UV-DRS, Raman, TG-DTA, XRD, EDX, XPS, SEM, TEM and BET analysis. Of the synthesized six samples of N-TiO₂ five samples showed better photocatalytic activity towards direct sunlight photo-degradation of methylene blue (MB) and rhodamine B (RhB) than Degussa P25. The catalysts obtained using semicarbazide samples F3 and F4 having large surface area of 76 and 85.8 m²/g displayed maximum photocatalytic activity. The sample F4 was 1.5 times more active than Degussa P25 for the decolourisation of MB and 1.9 times more active for the decolourisation of RhB. The presence of nitrogen, large surface area and coupling of rutile-anatase phases were found to be the main responsible factors for the enhanced photocatalytic activity. The exclusive formation of the anatase phase in the case of urea precursor is attributed to the slow evaporation of urea due to the formation of melamine derived products. The calcination temperature is the deciding factor responsible for the photocatalytic activity of the N-TiO₂ samples prepared from precursors which can potentially form the melamine and its oligomerized products on the surface of TiO₂.     

Structural characterization of Th-doped TiO2 photocatalyst and its extension of response to solar light for photocatalytic oxidation of oryzalin pesticide: a comparative study

The degradation efficiency of Th-doped TiO₂ / TiO₂ photocatalysts were investigated under UV and solar light illumination. The model compound chosen for the study was Oryzalin (OZ). Doping of inner transition metal ion Th was intended to modify the electronic properties of TiO₂. The Th-doped TiO₂ were synthesized by incorporating 0.02, 0.04, 0.06, and 0.1 atom percentage of Th into the TiO₂ lattice by solid-state reaction. The stochiometry of the prepared samples is Ti_1−xTh_xO₂, where ‘x’ is the percentage of Th. The samples were characterized by UV-Visible absorption, UV-Visible -Diffused reflectance spectra, Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Analysis (EDX) and X-ray Diffraction (XRD). The pore size and surface area of these samples were studied by Brunauer, Emmett and Teller (BET) adsorption method. It was found that metal ion doping at various percentage compositions enables a large shift in the absorption band of the TiO₂ towards visible light region. This is due to the formation of various mid band gaps at 2.84 eV, 2.804 eV, 2.66 eV, and 2.55 eV. The extent of degradation of the pesticide was followed by UV-Visible spectroscopy and GC-MS methods. Based on the spectral analysis, the probable degradation reaction mechanism for OZ is proposed. These results indicate that Th-doped TiO₂ with the modified electronic properties is a good catalyst under solar light irradiation. But these particles show marginal variation in rates under UV-illumination. All the photodegradation reactions follow the first order kinetics.      

Preparation and Photocatalytic Activity of TiO2 Films on Silica Glass Substrates by Assembly Technique

Nanostructured TiO₂ coating films on silica glass substrates were prepared by the assembly technique. TiO₂ colloids were synthesized employing the sol‐gel method using TiCl₄ as a precursor. The effect on the surface structures which was caused by the polyethylene glycol (PEG) added to the precursor solution and the photocatalytic activity were studied. The experimental results showed that the cobble‐like TiO₂ coating films were synthesized at 500 °C. On the surface of the samples, TiO₂ films exhibited uniform shape and a narrow size distribution. The result of proper PEG added to the precursor solution led to the decreasing of the size of TiO₂ particles and the increasing of the surface area of the samples. The photocatalytic activity of TiO₂ films with PEG was higher than that of samples without PEG.     

Biosynthesis of TiO<Subscript>2</Subscript> nanoparticles using <Emphasis Type="Italic">Justicia gendarussa</Emphasis> leaves for photocatalytic and toxicity studies

Eco-friendly biosynthesis of polycrystalline titanium dioxide (TiO₂) nanoparticles (NPs) was synthesised using Justicia gendarussa (J. gendarussa) leaf extract as oxidizing agents. They were compared with TiO₂ NPs synthesized using the glacial acetic acid and also studied was the combined effect of synthesis of TiO₂ NPs. The crystalline nature and structural formation of TiO₂ NPs synthesized by different methods were confirmed by the X-ray diffraction technique, and functional groups of materials were confirmed by FT-IR spectroscopy. The synthesized materials were investigated for photocatalytic activity for methylene blue under UV irradiation and toxicity activity against MCF-7 and MDA-MB-231 cells. The result indicates that TiO₂ NPs synthesised by J. gendarussa showed superior and enhanced activity against MCF-7 and MDA-MB-231. Biosynthesized TiO₂ NPs showed higher photodegradation of dyes when compared with other TiO₂ NPs synthesized by different methods. This is due to the alterations in band gap; structural changes and surface area in nanoparticles that increased the activity. Also, nanosphere/disc like morphology of TiO₂ NPs is confirmed using TEM.     

Ultrasonic Preparation of Hierarchical Graphene‐Oxide/TiO2 Composite Microspheres for Efficient Photocatalytic Hydrogen Production

Hierarchical graphene oxide (GO)‐TiO₂ composite microspheres with different GO/TiO₂ mass ratios were successfully prepared by mixing GO and TiO₂ microspheres under ultrasonic conditions. Ultrasonication helped the GO and TiO₂ microsphere to uniformly mix on the microscale. The results showed that the GO‐TiO₂ composites that were prepared by ultrasonic mixing exhibited significantly higher hydrogen‐evolution rates than those that were synthesized by simple mechanical grinding, owing to synergetic effects, including enhanced light absorption and scattering, as well as improved interfacial charge transfer because of the excellent contact between the GO sheets and TiO₂ microspheres. In addition, GO‐TiO₂‐3 (3 wt. % GO) showed the highest hydrogen‐generation rate (305.6 μmol h^?), which was about 13 and 3.3‐times higher than those of TiO₂ microsphere and GO‐P25 (with 3 wt. % GO), respectively. Finally, a tentative mechanism for hydrogen production is proposed and supported by photoluminescence and transient photocurrent measurements. This work highlights the potential applications of GO‐TiO₂ composite microspheres in the field of clean‐energy production.     

Ultraviolet Protection Characteristics of Silicone/Titanium Dioxide Composite Sheets

Silicone/titanium dioxide (TiO₂) composite sheets were prepared from TiO₂ particles and silicone elastomer by a compression-molding process at 140 °C. The particles were produced through sol-gel method, and emulsion technique consecutively. The prepared composite sheets with thickness of 0.8 mm had ultraviolet radiation protection property such that the transmission of ultraviolet (UV) B ray through the sheets was less than 1%. The UVA ray transmitted the sheets in the range of 0.02–4% at 320 nm and 2–43% at 400 nm, depending on the amount of TiO₂ emulsion presented in the silicone elastomer. The composite sheets still remained transparent since the transmission of the visible light through the sheets was up to 60%. On the other hand, the transmissions of UVB ray, UVA ray, and visible light through the pure silicone elastomer sheets were in the range of 47–58%, 58–71%, and 71–88%, respectively. Comparable with silicone elastomer sheets, the addition of TiO₂ emulsion resulted in the composite sheets with higher strain and lower modulus; however, these differences in tensile properties were up to the amount of the emulsion in the silicone elastomer.     

Solgel-hydrothermal synthesis of Tb/Tourmaline/TiO2 nano tubes and enhanced photocatalytic activity

In this study, we synthesized Tb/Tourmaline/TiO₂ nano tubes (NTs) through a solgel-hydrothermal method. The as-prepared samples were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectromicroscope, scanning electron microscopy, transmission electron microscopy and UV-vis diffuse reflectance spectroscopy. The resulting Tb/Tourmaline/TiO₂ NTs exhibited higher photocatalytic activity than pure TiO₂ and TiO₂ nano particles (NPs) in the degradation of menthyl orange under UV-light. Results revealed that doping rare earth element Tb could narrow the wide band gap of TiO₂ and tourmaline could trap the photogenerated electron of TiO₂ to inhibit the recombination of photogenerated electron-hole pairs.     

Degradation of organic compounds on TiO<Subscript>2</Subscript> photocatalysts prepared by a hydrothermal method in the presence of NH<Subscript>4</Subscript>F

TiO₂ photocatalysts were synthesized by a hydrothermal method from tetraisopropyl orthotitanate (TPOT) in the presence of NH₄F with different NH₄F/Ti molar ratios (0, 0.25, and 1). The formation of a well-crystallized anatase phase of TiO₂ and the suppression of phase transition to rutile were observed, even at high calcination temperature, owing to the effects of NH₄F. The TiO₂ synthesized hydrothermally with NH₄F exhibited absorption with a shift to the longer wavelengths of the visible-light region. The hydrothermally synthesized TiO₂ with a moderate amount of NH₄F exhibited high photocatalytic activity for the degradation of alcohol diluted in water under both UV-light and visible-light irradiations.     

Dye-Sensitized Solar Cell Utilizing TiO<Subscript>2</Subscript> Nanostructure Films: Effect of Synthesis Temperature

This paper is concerned with a study of the influence of synthesis temperature on the properties of TiO₂ films and the performance of dye-sensitized solar cell (DSSC). The TiO₂ film samples synthesized via liquid phase deposition for 5 h at various temperatures, namely, 40, 50, 60, 70 and 80°C. It was found that the morphological shape of the film changes with growth temperature. The optical absorption increases with growth temperature. However, the photoluminescence decreases with growth temperature. These TiO₂ samples were applied in a DSSC of ITO/TiO₂/electrolyte/platinum. The DSSC utilizing the sample grown at 40°C demonstrated the highest photovoltaic parameters with the J_sc, and η of 1.40 mA cm^–2 and 0.44% respectively. This is due to the smallest grain size of TiO₂ films and the smallest bulk resistance of the device.     

Boron and nitrogen-codoped TiO2 nanorods: Synthesis, characterization, and photoelectrochemical properties

Boron and nitrogen codoped TiO₂ nanorods (BNTRs) were synthesized via two-step hydrothermal reactions using TiN as a starting material. The as-prepared samples were characterized by X-ray diffraction, field-emission scanning electron microscope (SEM), transmission electron microscopy and X-ray photoelectron spectroscopy techniques. The results showed that TiO₂ nanorods with the diameter of approximately 50–100 nm and the length of several micrometers were doped by the interstitial N and B. The nanorods were firstly formed in the hydrothermal synthesis of nitrogen doped TiO₂. The growing process of nanorods was observed by SEM and a most probable formation mechanism of the trititanate nanorods was proposed. The BNTRs showed a higher photocatalytic activity and a bigger photocurrent response than N–TiO₂ nanorods under visible light irradiation.     

Effect of the support calcination temperature on selective hydrodesulfurization of TiO2 nanotubes supported CoMo catalysts

TiO₂ nanotubes (TiO₂-NTs) were synthesized by the hydrothermal method. Co and Mo active components were supported on a series of the as-prepared TiO₂-NTs samples which were calcined at different temperatures. The effects of support calcination temperature of CoMo/TiO₂-NTs catalysts on their catalytic performance were investigated for selective hydrodesulfurization (HDS). The samples were characterized by means of the scanning electron microscopy (SEM), the transmission electron microscopy (TEM), N₂ adsorption-desorption, X-ray diffraction (XRD), Raman spectroscopy and H₂ temperature-programmed reduction (H₂-TPR). The experimental results revealed that TiO₂-NTs support calcined under 500 °C can maintain the nanotubular structure with higher surface area and pore volume. Meanwhile, the obtained supported CoMo/TiO₂-NTs catalysts exhibited weak metal-support interaction, more octahedral Mo⁶⁺ species and high catalytic performance in selective HDS.     

Influence of surface modified TiO2 nanoparticles by gallates on the properties of PMMA/TiO2 nanocomposites

Nanocomposites based on poly(methyl methacrylate) (PMMA) and TiO₂ nanoparticles were synthesized by in situ radical polymerization of MMA in solution. The surface of TiO₂ nanoparticles was modified with four gallic acid esters (octyl, decyl, lauryl and cetyl gallate). The content of gallates present on the surface of TiO₂ was calculated from the TGA results. The influence of length of hydrophobic tail of amphiphilic alkyl gallates on dispersability of surface modified TiO₂ nanoparticles in PMMA matrix, the molecular weight and glass transition temperature of PMMA, as well as the thermal stability of the prepared PMMA/TiO₂ nanocomposites in nitrogen and air was investigated. The influence of content of TiO₂ nanoparticles on the properties of these nanocomposites was also examined. The formation of a charge transfer complex between the surface Ti atoms and the gallates was confirmed by FTIR and UV spectroscopy. TEM micrographs of the PMMA/TiO₂ nanocomposites revealed that degree of TiO₂ aggregation can be significantly lowered by increasing the length of aliphatic part of the used gallates. The molecular weight of PMMA slightly decreases with the increase of TiO₂ content, indicating that used TiO₂ nanoparticles act as radical scavengers during the polymerization of MMA. The presence of surface modified TiO₂ nanoparticles do not have an influence on the mobility of PMMA chain segments leading to the same values of glass transition temperature for all investigated samples. Thermal and thermo-oxidative stability of the PMMA matrix are improved by introducing TiO₂ nanoparticles modified with gallates.     

TiO2–B Nanosheets/Anatase Nanocrystals Co‐Anchored on Nanoporous Graphene: In Situ Reduction–Hydrolysis Synthesis and Their Superior Rate Performance as an Anode Material

A unique hybrid, TiO₂–B nanosheets/anatase nanocrystals co‐anchored on nanoporous graphene sheets, can be synthesized by a facile microwave‐induced in situ reduction–hydrolysis route. The as‐formed nanohybrid has a hierarchically porous structure, involving both mesopores of approximately 4 nm and meso‐/macropores of 30–60 nm in the graphene sheets, and a large surface area. Importantly, electrodes composed of the nanohybrid exhibit superior rate capability (160 mA h g^?1 at ca. 36 C; 154 mA h g^?1 at ca. 72 C) and excellent cyclability. The synergistic effects of conductive graphene with numerous nanopores and the pseudocapacitive effect of ultrafine TiO₂–B nanosheets and anatase nanocrystals endow the hybrid a superior rate capability.     

Synthesis of TiO<Subscript>2</Subscript> nanotubes using different alkaline media and their applications in photocatalysis and DSSCs

TiO₂ nanotubes (TNTs) were successfully synthesized from different alkaline media (i.e., NaOH and KOH) by using a microwave hydrothermal process. The effects of different alkaline media on the formation of TiO₂ nanotubes and their physicochemical properties were investigated. The phases of different TiO₂ nanostructures were studied by using X-ray diffraction patterns. Morphologies of the nanostructures were observed with a transmission electron microscope. The optical properties of the nanostructures were evaluated through the absorption behavior using UV–Vis diffuse reflectance spectroscopy. The photocatalytic activities of the TiO₂ nanostructures were evaluated by the degradation of methylene blue aqueous dye solution under the simulated solar light irradiation. Similarly, the photovoltaic efficiencies of the prepared samples were investigated by making photo-anode layers in the Dye Sensitized Solar Cells (DSSCs). The results revealed that in comparison to the single layered TiO₂ nanostructures in the DSSC, creation of a double layer structure significantly enhanced the efficiency of DSSC.     

Pt 改性的高结晶度 TiO2 晶须的光催化性能

 以二钛酸钾 (K₂Ti₂O₅) 为前驱体, 通过离子交换和 800^oC 焙烧制备了 TiO₂晶须 (TiO₂(800^oC)), 并采用乙二醇胶体法, 在 TiO₂(800^oC) 样品上负载 1% Pt 纳米颗粒制成了 Pt/TiO₂(800^oC 催化剂. 采用 X 射线衍射、扫描电镜、透射电镜、X 荧光光谱和低温 N2 吸附-脱附等技术对催化剂进行了表征, 并考察了该催化剂光催化降解苯酚活性及稳定性. 结果表明, TiO₂(800^oC)样品为结晶度较高的纯锐钛矿 TiO₂, 载 Pt 后催化活性提高到原来的 2.3 倍, 具有很高的单位比表面积活性. 催化剂经 10 次重复使用后, Pt 流失量仅为 6%, 活性为新鲜催化剂的 91%. 而低结晶度的纯锐钛矿或混晶的 TiO₂ 负载 Pt 催化剂的活性和稳定性均不及 Pt/TiO₂(800^oC).