Maleic Anhydride Polyethylene Octene Elastomer Toughened Polyamide 6/Polypropylene Nanocomposites: Mechanical and Morphological Properties

A series of polyamide 6/polypropylene (PA6/PP) blends and nanocomposites containing 4 wt% of organophilic modified montmorillonite (MMT) were designed and prepared by melt compounding followed by injection molding. Maleic anhydride polyethylene octene elastomer (POEgMAH) was used as impact modifier as well as compatibilizer in the blend system. Three weight ratios of PA6/PP blends were prepared i.e. 80:20, 70:30, and 60:40. The mechanical properties of PA6/PP blends and nanocomposite were studied through flexural and impact properties. Scanning electron microscopy (SEM) was used to study the microstructure. The incorporation of 10 wt% POEgMAH into PA6/PP blends significantly increased the toughness with a corresponding reduction in strength and stiffness. However, on further addition of 4 wt% organoclay, the strength and modulus increased but with a sacrifice in impact strength. It was also found that the mechanical properties are a function of blend ratio with 70:30 PA6/PP having the highest impact strength, both for blends and nanocomposites. The morphological study revealed that within the blend ratio studied, the higher the PA6 content, the finer were the POEgMAH particles.     

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

The mechanical properties and dynamic mechanical properties of blends composed of Nylon 6 and poly(butylenes terephthalate)(PBT),with styrene/maleic anhydride(SMA)as compatibilizer,were studied.The observation on the morphologies of the etched surfaces of the cryogenically fractured specimens via scanning electron microscopy(SEM)demonstrated that in the compatibilized Nylon 6/PBT blends,there exists a finer and more uniform dispersion induced by the in-situ interfacial chemical reactions during the preparation than that in the corresponding uncompatibilized blends.On the other hand,the overall mechanical properties of the compatibilized blends could be remarkably improved compared with those of the uncompatibilized ones.Moreover,increasing the amount of the compatibilizer SMA leads to a more efficient dispersion of the PBT phase in Nylon 6/PBT blends.Furthermore,there exists an optimum level of SMA added to achieve the maximum mechanical properties.As far as the mechanism of this reactive compatibilization is concerned,the enhanced interfacial adhesion is necessary to obtain improved dispersion,stable phase morphology,and better mechanical properties.     

Barrier,Mechanical, Morphological and Thermal Properties of Compatibilized High Density Polyethylene and Polyamide 6 Blends

Effectiveness of the content of maleic anhydride (MAH) and polyamide 6 (PA6) on mechanical, thermal, barrier (moisture and oxygen) properties of HDPE/PA6 blends was investigated. Blends of HDPE with PA6 were prepared by in situ method. Molau test and FTIR spectroscopy results confirmed the reactive compatibilization through grafting of MAH on HDPE and PA6 chains in PA6/HDPE blends. Low concentration of benzoyl peroxide (BPO) and MAH reduced the particle size, improved phase morphology and mechanical properties of PA6/HDPE blends. Decrease in mechanical properties of PA6/HDPE blends was observed at high concentration of BPO and MAH.     

Synthesis and Properties of Nonionic Surfactants from Rosin-Imides Maleic Anhydride Adduct

Ester-adduct derivatives of rosin were synthesized by reacting rosin with polyethylene glycol 600 (PEG 600) or 2000 (PEG2000) and maleic anhydride (MA) at elevated temperature. These derivatives were evaluated for acid number, FTIR spectroscopy, molecular weight (Mw), and polydispersity. The derivatives were soluble in organic solvents; aqueous solubility was pH dependent. Rosin-imides were synthesized from a rosin ester-maleic anhydride adducts. It was condensed with diaminobutane or triethylene tetramine to obtain rosinimides. This imide was etherified by reaction with PEG in the presence of β,β′-dichlorodiethyl ether as a linking agent and NaOH as a catalyst. The surface properties of the prepared surfactants were determined by measuring the surface tension at different temperatures. The surface tension, critical micelle concentration and surface activities were determined at different temperatures. Surface parameters such as surface excess concentration (Γmax), the area per molecule at interface (Amin), and the effectiveness of surface tension reduction (πCMC) were determined from the adsorption isotherms of the prepared surfactants. Some thermodynamic data for the adsorption process were calculated and are discussed.     

马来酸酐(MAH)表面改性纳米碳酸钙粉体的制备及表面性能

通过在两相法制备纳米碳酸钙的过程中添加一定量的马来酸酐(MAH)的方法，在纳米碳酸钙的表面引入羧基、羟基、双键等活性基团对纳米碳酸钙进行表面改性，并通过调节马来酸酐的用量，有效地控制纳米碳酸钙的极性和表面能。接触角实验结果表明，当马来酸酐的加入量为2%时可以获得界面性能最理想的改性纳米碳酸钙。还在此基础上提出了马来酸酐(MAH)对纳米碳酸钙进行表面改性的过程机理，并以SEM，ATR-FTIR和TGA等手段对上述过程机理进行了验证。     

环氧树脂／聚氧乙烯固化共混体系的动态力学性能

研究了环氧树脂／聚氧乙烯分别在邻苯二甲酸酐和４，４’－二氨基二苯甲烷为固化剂条件下的固化剂用量，类型和固化共混物的动态力学性能。结果表明所有共混物在熔副态和非晶态都是相容的，即在高温区都存在一个α松驰，玻璃化转变温度随共混组成有规律地变化，不同固化剂的固化物交网的化学结构不同，因而低温松弛－β松弛机制也不同，同时其对体系的交联密度，共混组成的依赖性也不同。     

Determination of Hydroxyl Groups in Epoxy Resins by Potentiometric Titration Using a Reaction with Maleic Anhydride

A reaction of maleic anhydride with epoxy–dian resins in methyl ethyl ketene was investigated. It was shown by potentiometric titration that the resulting maleic esters are stable to hydrolysis in acid and weakly acid organic solutions. This reaction can be used for the quantitative determination of hydroxyl groups in epoxy resins. Epoxy groups do not interfere with the formation of maleic esters under the conditions of determination. The optimal reaction conditions were found. The reaction kinetic was investigated, the reaction rate constants were determined at various temperatures, and the activation energy was found. The value of the activation energy indicates that the reaction is characterized by a low potential barrier.     

Chemical Modification of Polystyrene. VI. Thermal Stability Studies of Sulfonic Acid Resins from Anhydride Modified Polystyrene

Thermal stabilities of the H form of sulfonic acid resins from polystyrene electrophilically substituted with phthalic anhydride, pyro-mellitic dianhydride, trimellitic anhydride, and cis-1,2,3,6-tetra-hydrophthalic anhydride have been studied and compared by DTA and TGA. Isothermal degradation studies of these resins at 150 ± 10°C for 72 h in air and nitrogen reveal significant changes in IR, decreases in sulfur content, and increases in ion-exchange capacity values. The pH-metric titration characteristics of the pyro-mellitic-dianhydride-modified sulfonated polystyrene after isothermal heating under the above conditions indicate weak acid behavior, in contrast to the strong acid nature of the original resin.     

Preparation and Properties of Polymers Derived from Epoxy Resins and Oligochelatotitanophenylenesiloxanes

Oligochelatotitanophenylenesiloxanes of various structures were suggested as curing agents for epoxy resins. The compound formulas and curing conditions were chosen so as to ensure the maximal degree of cross-linking and hence the best physicomechanical properties of the polymers.     

Influence of Reactive Compatibilization on the Melt Flow Properties and Morphology of Polyamide 6/Styrene-Acrylonitrile Blends

Summary: In this study, we investigate the influence of reactive compatibilization on the rheological properties of polyamide 6/styrene-acrylonitrile (PA 6/SAN) blends in the melt. Linear viscoelastic shear oscillations, simple elongation to a large stretch ratio and subsequent recovery experiments were performed. The morphology of the blends was examined by atomic force microscopy. We prepared three PA 6/SAN blends with different composition ratios of PA 6 and SAN (70/30, 50/50, 30/70) and a constant concentration of the reactive agent. Our experiments revealed that reactive compatibilization significantly increases the complex modulus of PA 6/SAN blends at low frequencies. In particular, the data of the PA 6/SAN 50/50 blend and the PA 6/SAN 30/70 blend indicated that an elastic network between neighbouring PA 6 domains was formed. In simple elongation, the transient elongational viscosity of the blends exceeded the values of the single components. In recovery, the recovered stretch of all blends was larger than the recovered stretch of the pure components. The differences of the blend morphology and of the linear viscoelastic behaviour were qualitatively explained by the asymmetric properties of the reactively compatibilized interface.     

Crystalline Morphology and Crystallization Characteristics of In-situ Blends of Anionic Polyamide 6 with Noncrystallizable Semiaromatic Polyamide Copolymer

A noncrystallizable semiaromatic polyamide copolymer(NSAP) was dissolved in molten caprolactam, and PA6/NSAP blends were produced in-situ via the anionic ring-opening polymerization of caprolactam. The presence of a single loss tangent(tanδ) peak measured by means of dynamic mechanical analysis(DMA) proves the miscibility between PA6 and NSAP in the blends. It was found that there existed drastic changes in the crystallographic form and crystallization kinetics for the in-situ blends, e.g., when 20% NSAP was added, nearly all crystallites existed in the γ form and the crystallization could hardly occur upon cooling even at a rate of 2.5 ℃/min. Moreover, cold crystallization appears during the subsequent heating, and its melting point is 40 ℃ lower than that of the virgin system. On the other hand, the size of the spherulites only decreases modestly. It is suggested that the introduction of irregular stiff segments originated from NSAP into PA6 macromolecule chain, which resulted from transamidation during the polymerization play a dominant role in the drastic change of crystallization kinetics and the resultant morphology of the in-situ blends.     

Organic/Inorganic Hybrid Materials Based on Silsesquioxanes Derived from (3-Methacryloxypropyl) Trimethoxysilane and Their Blends with Vinylester Resins

The crosslinking of blends of a silsesquioxane (SSO) derived from (3-methacryloxypropyl) trimethoxysilane, variable amounts of a vinylester resin (VE, dimethacrylate of bisphenol A), and benzoyl peroxide (BPO) or dicumyl peroxide (DCP) as initiators, was followed by differential scanning calorimetry (DSC). For the neat SSO a thermally-initiated polymerization was observed in the 150–250°C range, leading to a conversion close to 22% of the initial C=C groups. The final conversion could be increased to a maximum value close to 83%, by adding an initiator and using a thermal cycle attaining temperatures in the range of 200°C. The use of variable amounts of VE as a co-monomer produced a slight increase of the final conversion in SSO/VE/BPO blends. Neither the conversion of double-bonds nor the addition of the VE had any effect on the onset temperature of thermal degradation, which was associated to the presence of the methacryloxypropyl groups supplied by the SSO and the VE resin. However, a distinct two-step degradation process was observed in the presence of VE. Coatings based on SSO/VE/BPO blends exhibited more uniform thicknesses and lower values of the microhardness than those devoid of VE. However, the conversion of C=C groups did not show any significant effect on the values of microhardness.     

Synthesis and Fluorescence Properties of Gold Nanoparticles Modified with Dithiocarbamate Functionalized Carbazole

Gold nanoparticles protected by the self-assembled monolayers of 9-[6-(N,N-dibutyl-amino-dithiocarbamate)-hexyl]-carbazole, CHBDTC in short, were prepared via a phase-transfer method. These surface-modified nanoparticles were characterized with UV-vis, photoluminescence spectroscopy and TEM. It was found that the CHBDTC-capped gold nanoparticles were stable under ambient conditions, which is attributed to the protection of the CHBDTC densely packed on the gold nanoparticle surface. The fluorescence emission spectra indicated that the fluorescence of CHBDTC was quenched to some extent by gold nanoparticles. And the CHBDTC-capped Au nanoparticles could be promisingly applied as biomolecular labels and in fabrication of novel photo-based nanodevices as well, owing to the photoactive sensitivity of CHBDTC.     

Some Properties of Blends Based on High Density Polyethylene Grafted with Di-2-Ethyl-Hexyl Fumarat

Abstract

Blends based on high density polyethylene (MFI=0.3 g/10 min) and low density polyethylene grafted with di-2-ethyl-hexyl fumarate are presented.

These blends were obtained through component homogenization, in different proportions, on a Berstorff laboratory roll-mill, for 10 minutes at 180°C.

Low density polyethylene (MFI=2.0 g/10min) grafting was carried out in polymer melt, through radicalic initiation, in the presence of organic peroxides, at a temperature of 140—160°C. The content of the monomer grafted on polymer chain was determined through IR absorption spectrophotometry using the absorption band of 1735 cm^?1.

From the experimental, obtained blends plates, 1 mm thick, were manufactured with the purpose of determining the main tensile properties.

For the respective blends melt flow index evolution were followed.     

Polymeric Nitrofuran Derivatives. II. Chemical Modification of Functionalized Resins with Nitrofuran Derivatives

Polymeric nitrofuran derivatives have been synthesized by chemical modification of macroporous styrene-divinylbenzene copolymers with low molecular weight nitrofurans. The 5-nitrofuryl groups are covalently attached to the polymeric carrier by azomethine, ester, N-alkyl, and sulfamide links, respectively. Comparative hydrolysis studies and biological tests of the modified resins suggested that the polymeric carrier-bound nitrofurans are antimicrobially active. The polymeric nitrofurans have been characterized by IR and “C-solid-NMR spectroscopy”.     

Non‐Woven Fibrous Materials with Antibacterial Properties Prepared by Tailored Attachment of Quaternized Chitosan to Electrospun Mats from Maleic Anhydride Copolymer

In order to impart antibacterial properties to microfibrous electrospun materials from styrene/maleic anhydride copolymers, quaternized chitosan derivatives (QCh) containing alkyl substituents of different chain lengths are covalently attached to the mats. A complete inhibition of the growth of bacteria, S. aureus (Gram‐positive) and E. coli (Gram‐negative), for a contact time of 30–120 min or a decrease of the bacterial titer by 2–3 log units is observed depending on the quaternization degree, the chain length of the alkyl substituent, and the molar mass of QCh. The modified mats are also effective in suppressing the adhesion of pathogenic S. aureus bacteria.

     

显微镜图像分析研究非相容高密度聚乙烯/尼龙1010共混体系熔体动态过程中相结构的形成与发展

讨论了非相容高密度聚乙烯,尼龙1010共混体系在熔融混炼过程中相结构的形成与发展.应用在线连续采样方法,获得共混过程中体系不同时刻的样品,应用扫描电子显微镜观察并得到共混物相结构的显微图像.用图像处理和图估计方法求得了体系分散相平均粒径和粒径分布宽度,讨论了平均粒径和分布宽度随混炼时间的变化.结果表明,共混物相结构的变化主要发生在混炼初期,即混炼两分钟以前,之后平均粒径和分布宽度趋于平稳,保持在一定数值范围内.引入分性概念,应用测度法计算了体系的分形维数,表明体系相结构的变化具有自相似性,分形维数的变化与体系的均匀性有关.同时,研究了混炼温度和混炼设备的转速(剪切速率)与体系分散相平均粒径、分布宽度和分形维数等结构参数的关系.     

Electrospun Mats from Styrene/Maleic Anhydride Copolymers: Modification with Amines and Assessment of Antimicrobial Activity

New antimicrobial microfibrous electrospun mats from styrene/maleic anhydride copolymers were prepared. Two approaches were applied: (i) grafting of poly(propylene glycol) monoamine (Jeffamine® M‐600) on the mats followed by formation of complex with iodine; (ii) modification of the mats with amines of 8‐hydroxyquinoline or biguanide type with antimicrobial activity. Microbiological screening against S. aureus, E. coli and C. albicans revealed that both the formation of complex with iodine and the covalent attachment of 5‐amino‐8‐hydroxyquinoline or of chlorhexidine impart high antimicrobial activity to the mats. In addition, S. aureus bacteria did not adhere to modified mats.

     

Donor-Acceptor Complexes in Copolymerization. XXXVI. Alternating Diene-Dienophile Copolymers. 4. Copolymerization of Furan and 2-Methylfuran with Maleic Anhydride

Abstract

The copolymerization of furan and 2-methylfuran with maleic anhydride in the presence of a radical catalyst yields equimolar, alternating copolymers in which the furan units have a 2,5-linkage (NMR and IR). The copolymerization appears to have a floor temperature of about 40°C. The furan-maleic anhydride Diels-Alder adduct polymerizes in solution in the presence of a radical catalyst at temperatures above 60°C to yield the identical copolymer as is obtained from the monomers. The adduct undergoes a retrograde reaction above 60°C to regenerate the monomers which then copolymerize through excitation of the ground state comonomer charge transfer complex.