Thermodynamic properties of noble metal clusters:molecular dynamics simulation

The thermodynamics properties of noble metal clusters Au_N, Ag_N, Cu_N, and Pt_N (N = 80, 106, 140, 180, 216, 256, 312, 360, 408, 500, 628, 736, and 864) are simulated by micro-canonical molecular dynamics simulation technique. The potential energy and heat capacities change with temperature are obtained. The results reveal that the phase transition temperature of big noble metal clusters (N ⩾ 312 for Au, 180 for Ag and Cu, and 360 for Pt) increases linearly with the atom number slowly and approaches gently to bulk crystals. This phenomenon indicates that clusters are intermediate between single atoms and molecules and bulk crystals. But for the small noble clusters, the phase transition temperature changes irregularly with the atom number due to surface effect. All noble metal clusters have negative heat capacity around the solid-liquid phase transition temperature, and hysteresis in the melting/freezing circle is derived in noble metal clusters.     

Ternary alloying effect on the melting of metal clusters

Canonical ensemble Monte Carlo simulations are applied to investigate the melting of the icosahedral 55-atom Ag-Cu-Au clusters. The clusters are modeled by the second-moment approximation of the tight-binding (TB-SMA) many-body potentials. Results show that the introduction of the only Cu atom of the third alloying metal in the bimetallic Ag₄₃Au₁₂ cluster, forming the Ag₄₂Cu₁Au₁₂ cluster, can greatly increase the melting point of the cluster by about 100 K. It is also found that the substitution of the only Cu atom of the third alloying metal in the Ag₁Au₅₄ clusters, forming the Ag₁Cu₁Au₅₃ cluster, can result in an increase of 40 K in the melting point. It can be concluded that the melting points of the bimetallic clusters can be tuned by the third metal impurities doping. In addition, the surface segregation of Ag atoms in the Ag-Cu-Au trimetallic clusters occurs even after melting.     

熔融Cu55团簇在铜块体中凝固过程的分子动力学模拟

应用基于嵌入原子势函数的分子动力学方法,模拟了嵌入在具有面心立方结构同质块体中的熔融Cu₅₅团簇在不同急冷温度下微观结构的演变情况.通过计算熔融Cu₅₅团簇的均方位移和原子平均能量随时间步的变化,并应用键对分析技术,分析了急冷温度对熔融Cu₅₅团簇结构变化的影响.研究结果表明,由于受到块体结构的影响,在所研究的急冷温度范围内,熔融Cu₅₅团簇在凝固过程中形成了以面心立方结构为主的微观结构.结晶过程是原子不断交换其位置的过程,团簇原子位置的重排敏感于温度的变化.随着急冷温度的升高,原子的扩散范围增大.在100,300和500 K三个较低的温度下有利于形成稳定的面心立方结构,但当急冷到100 K时,团簇中的原子在没有找到其最佳位置之前就已经完成晶化.在急冷到500 K时,团簇中的原子在块体中扩散充分,与块体中的原子形成理想的面心立方结构.在700,900和1100 K三个较高的温度上,局域结构表现为随时间步波动性变化. 关键词： 团簇 分子动力学 计算机模拟 凝固     

Synthesis of NiAu alloy and core–shell nanoparticles in water-in-oil microemulsions

NiAu alloy nanoparticles with various Ni/Au molar ratios were synthesized by the hydrazine reduction of nickel chloride and hydrogen tetrachloroaurate in the microemulsion system. They had a face-centered cubic structure and a mean diameter of 6–13 nm, decreasing with increasing Au content. As Au nanoparticles did, they showed a characteristic absorption peak at about 520 nm but the intensity decreased with increasing Ni content. Also, they were nearly superparamagnetic, although the magnetization decreased significantly with increasing Au content. Under an external magnetic field, they could be self-organized into the parallel lines. In addition, the core–shell nanoparticles, Ni₃Au₁@Au, were prepared by the Au coating on the surface of Ni₃Au₁ alloy nanoparticles. By increasing the hydrogen tetrachloroaurate concentration for Au coating, the thickness of Au shells could be raised and led to an enhanced and red-shifted surface plasmon absorption.     

Molecular-dynamics investigation of structural transformations of a Cu201 cluster in its melting process

We perform molecular-dynamics calculations to investigate the structural transformation of a copper cluster containing 201 atoms in its melting process within the framework of the embedded-atom method (EAM). Concerning melting, the obtained results reveal that its structural changes are different from those of larger-size clusters containing several hundreds or more atoms and smaller-size clusters containing tens of atoms. The melting process of this Cu₂₀₁ cluster involves three stages, firstly some atoms in inner regions of this cluster move into outer regions accompanying the structural transformation of the local atom packing, followed by the continuous interchange of atomic positions, and finally this cluster is wholly disordered. During the temperature increase, the structural changes of different regions determined by atom density profiles result in apparent increases in internal energy. By decomposing peaks of pair distribution functions (PDFs) according to the pair analysis (PA) technique, the local structural patterns are identified for the melting of this cluster.     

Geometric,stability, and electronic properties of gold-doped Pd clusters (Pd<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>Au, <Emphasis Type="Italic">n</Emphasis> = 3~20)

The structure, stability, and electronic properties of Pd _n Au (n = 3~20) clusters are studied by density functional theory. The results show that the clusters studied here prefer three-dimensional structures even with very small atom number. It is found that the binding energies of Pd _n Au clusters are higher than the corresponding pure Pd _n clusters with the same atom number. Most Pd _n Au clusters studied here are magnetic with magnetic moments ranging from 1.0 to 7.0 μ _B. The dissociation energies of Pd atoms are lower than the doped gold atom, that is the doped Au atom will increase the mother clusters stability and activity.     

Thermodynamic properties of noble metal clusters: molecular dynamics simulation

The thermodynamics properties of noble metal clusters Au_N, Ag_N, Cu_N, and Pt_N (N = 80, 106, 140, 180, 216, 256, 312, 360, 408, 500, 628, 736, and 864) are simulated by micro-canonical molecular dynamics simulation technique. The potential energy and heat capacities change with temperature are obtained. The results reveal that the phase transition temperature of big noble metal clusters (N ? 312 for Au, 180 for Ag and Cu, and 360 for Pt) increases linearly with the atom number slowly and approaches gently to bulk crystals. This phenomenon indicates that clusters are intermediate between single atoms and molecules and bulk crystals. But for the small noble clusters, the phase transition temperature changes irregularly with the atom number due to surface effect. All noble metal clusters have negative heat capacity around the solid-liquid phase transition temperature, and hysteresis in the melting/freezing circle is derived in noble metal clusters.     

First-principles studies: Thiolated Au2Cr and Au6Cr clusters

The structural, energetic and magnetic properties of thiol-passivating Au₂Cr and Au₆Cr clusters are investigated by performing first-principles calculation based on density functional theory. We find that the adsorption of thiolate is energetically more favorable than thiol and that the thiolates favor “top” site adsorption on Cr atom in one methanethiolate adsorbed Au₂Cr cluster while they favor “bridge” site adsorption on top of the middle point of Cr–Au bonds in three methanethiolates adsorbed Au₂Cr cluster. In thiol-passivating Au₆Cr cluster, the thiol favor “top” site adsorption on top of atom Au while the thiolate favor “bridge” site adsorption on top of the middle point of Au–Au bonds. The energetics of the reactions indicates that these thiol-passivating Au₂Cr or Au₆Cr clusters can be used as hydrogen storage materials. There are large and positive spin populations on atom Cr. The spin populations of atoms Au, S and H are attributed to both the spin delocalization and the spin polarization mechanisms.     

Elaboration and characterization of bimetallic nanoparticles obtained by laser ablation of Ni75Pd25 and Au75Ag25 targets in water

A YAG laser operating at the second harmonic wavelength (532 nm, 10 Hz, 8 ns and 40 mJ) was used to elaborate bimetallic nanoparticles by laser ablation of Ni₇₅Pd₂₅ and Au₇₅Ag₂₅ targets in water. TEM–EDX, UV–Vis spectroscopy and PIXE measurements were performed to obtain information on their mean sizes, size distributions and chemical composition as a function of the time of laser ablation. The surface of the laser impacted regions of the targets were characterized by RBS in order to check their composition after the laser ablation. The so-obtained bimetallic nanoparticles always show a homogeneous composition. However, while the composition of Au–Ag nanoparticles was found to be very similar to the one of the alloy target, the composition of the Ni–Pd nanoparticles can be different from the nominal composition of the alloy target. Segregation phenomena can be invoked to explain the difference between the Ni–Pd nanoparticles and the Au–Ag nanoparticles compositions obtained in the same conditions. However, an influence of chemical reactions occurring in the high pressure plasma created locally at liquid–solid interface (called ‘reactive quenching’) cannot be completely ruled out.     

Cu-Co双金属团簇结构演化及其性质的分子动力学模拟

采用分子动力学结合嵌入原子方法对比研究了Co分布于Cu-Co团簇不同层的结构和性质.研究表明:Co原子分层掺杂可对团簇的结构转变点和熔点进行诱导控制;分层掺杂的Cu-Co团簇第一相变是一种扩散度较小的由立方八面体转变为二十面体的相变;Co原子易于向低能态团簇的亚表层(111)面偏析,从而诱导团簇结构紊乱,造成其熔点差异.     

Cu-Co双金属团簇结构演化及其性质的分子动力学模拟

采用分子动力学结合嵌入原子方法对比研究了Co分布于Cu-Co团簇不同层的结构和性质. 研究表明：Co原子分层掺杂可对团簇的结构转变点和熔点进行诱导控制;分层掺杂的Cu-Co团簇第一相变是一种扩散度较小的由立方八面体转变为二十面体的相变;Co原子易于向低能态团簇的亚表层（111）面偏析, 从而诱导团簇结构紊乱, 造成其熔点差异.     

Structural features of melts in the In-Bi system

A testing device for the resistivity of high-temperature melt was adopted to measure the resistivity of In-Bi system melts at different temperatures. The resistivity of In_xBi_100−x(x=0-100) melt is in linear relationship with temperature, which is within the temperature measuring range. The resistivity of melt lowers with the increase of the In content. Based on Nordheim law and combined with the experimental resistivity of In-Bi melts, we verified the existence of InBi atom clusters and estimated the mole fraction of the InBi atom clusters in the melt, and the estimated value shows fine consistency with the result in literature [1]. The study reveals that the structural feature of In-Bi melts can be briefly divided into two intervals: in the interval of 0-50 at% In, the structural feature of the melt is that InBi atom clusters distribute in matrices, which have similar properties of Bi; in the interval of 50 at%-100 at% In, the structural feature of the melt is that InBi atom clusters distribute in matrices, which have similar properties of In. The content of InBi atom clusters in In₅₀Bi₅₀ melts reaches a higher value when the temperature is cooled down to a point, which is 152 K above the melting point. At the same time, the melts have an obvious fluctuation of concentration, which leads to that the resistivity of the melts deviates from the linear relationship at high temperature.     

A study of melting of various types of Pt–Pd nanoparticles

The melting processes of various Pt–Pd nanoparticles (binary alloy, core–shell, D ≤ 4.0 nm) with different percent platinum atom content are investigated via the molecular dynamics using the embedded atom method potential in order to establish the thermal stability of simulated particle structure. In accordance with the data obtained, the most thermally stable are Pt–Pd nanoalloys with a diameter above 2.0 nm and core–shell Pd@Pt particles. As is shown, heating of binary Pt–Pd cluster alloys with the particle diameters less than 2.0 nm may cause the transition to pentagonal symmetry structures and core–shell-like complex formations.

     

Phase transitions and kinetic properties of gold nanoparticles confined between two-layer graphene nanosheets

The thermodynamic and kinetic behaviors of gold nanoparticles confined between two-layer graphene nanosheets (two-layer-GNSs) are examined and investigated during heating and cooling processes via molecular dynamics (MD) simulation technique. An EAM potential is applied to represent the gold–gold interactions while a Lennard–Jones (L–J) potential is used to describe the gold–GNS interactions. The MD melting temperature of 1345 K for bulk gold is close to the experimental value (1337 K), confirming that the EAM potential used to describe gold–gold interactions is reliable. On the other hand, the melting temperatures of gold clusters supported on graphite bilayer are corrected to the corresponding experimental values by adjusting the ε_Au–C value. Therefore, the subsequent results from current work are reliable. The gold nanoparticles confined within two-layer GNSs exhibit face center cubic structures, which is similar to those of free gold clusters and bulk gold. The melting points, heats of fusion, and heat capacities of the confined gold nanoparticles are predicted based on the plots of total energies against temperature. The density distribution perpendicular to GNS suggests that the freezing of confined gold nanoparticles starts from outermost layers. The confined gold clusters exhibit layering phenomenon even in liquid state. The transition of order–disorder in each layer is an essential characteristic in structure for the freezing phase transition of the confined gold clusters. Additionally, some vital kinetic data are obtained in terms of classical nucleation theory.     

Formation of the structure of gold nanoclusters during crystallization

The structure formation in gold nanoparticles 1.6–5.0 nm in diameter is studied by molecular dynamics simulation using a tight-binding potential. The simulation shows that the initial fcc phase in small Au clusters transforms into other structural modifications as temperature changes. As the cluster size increases, the transition temperature shifts toward the melting temperature of the cluster. The effect of various crystallization conditions on the formation of the internal structure of gold nanoclusters is studied in terms of microcanonical and canonical ensembles. The stability boundaries of various crystalline isomers are analyzed. The obtained dependences are compared with the corresponding data obtained for copper and nickel nanoparticles. The structure formation during crystallization is found to be characterized by a clear effect of the particle size on the stability of a certain isomer modification. Nickel and copper clusters are shown to exhibit common features in the formation of their structural properties, whereas gold clusters demonstrate much more complex behavior.     

Composition distributions in FePt(Au) nanoparticles

Ternary alloy FePt(Au) nanoparticles were prepared by the co-reduction of platinum(II) acetylacetonate and gold(III) acetate and the thermal decomposition of iron pentacarbonyl in hot phenyl ether in the presence of oleic acid and oleylamine ligands. This gave spherical particles with an average diameter of 4.4 nm with a range of diameters from approximately 1.6–9 nm. The as-synthesized particles had a solid solution, face-centered-cubic structure. Though the average composition of the particles was Fe₄₄Pt₄₅Au₁₁, individual particle analysis by Scanning Transmission Electron Microscopy–X-ray Energy Dispersive Spectroscopy showed a broad distribution in composition. In general, smaller-sized particles tended to have a lower amount of Au as compared to larger-sized particles. As the Au content increased, the ratio of Fe/Pt widened.     

小尺寸铝纳米团簇的相变行为

采用分子动力学方法模拟了半径从0.3–1.3 nm变化的小尺寸铝纳米团簇的熔化、凝固行为. 基于势能-温度曲线、热容-温度曲线分析, 获得了熔点、凝固点与尺寸的依变关系, 并利用表面能理论、小尺寸效应开展了现象分析.研究表明, 铝团簇原子数小于80时, 熔点和凝固点的尺寸依赖性出现无规律的异常变化; 而大于该原子数, 熔、凝固点则随着团簇尺寸的减小而单调下降; 当原子数为27时, 团簇熔点高于块材熔点近40 K. 同时, 铝纳米团簇呈现出凝固滞后现象, 即凝固点低于熔点. 关键词： 纳米团簇 熔点 凝固点 分子动力学     

Cu60Zr30Ti10非晶合金弛豫和晶化过程的小角X射线散射研究

应用小角X射线散射技术研究了Cu₆₀Zr₃₀Ti₁₀非晶合金从300到813 K之间微结构的演化情况.发现在淬火状态下Cu₆₀Zr₃₀Ti₁₀非晶合金中存在直径30 nm左右的富Cu区.非晶的结构弛豫包括573 K之前的低温结构弛豫和573 K到玻璃转变温度的高温结构弛豫，弛豫的结果是产生含有有序原子团簇的富Cu区，这些有序原子团簇的富Cu区是随后晶化过程中晶核产生的基础.Porod曲线分析表明，晶化生成的纳米体心立方CuZr相和基体之间有明锐的界面. 关键词： 小角X射线散射 非晶合金 结构弛豫 晶化     

Hcp-icosahedron structural transformation induced by the change in Ag concentration during the freezing of （CoAg）561 clusters

The synergy effect of alloy elements in bimetallic clusters can be used to tune the chemical and physical properties. Research on the influences of alloy concentration and distribution on the frozen structure of bimetallic clusters plays a key rolc in exploring new structural materials. In this paper, we study the influence of Ag concentration on the frozen structure of the （AgCo）561 cluster by using molecular dynamics simulation with a general embedded atom method. The results indicate that tt~e structure and chemical ordering of the （AgCo）561 cluster are strongly related to Ag concentration. Hcp-icosahedron structural transformation in the frozen （CoAg）561 cluster can be induced by changing Ag concentration. The chemical ordering also transforms to Janus-like Co Ag from core-shell Co-Ag.     

Plasmonics properties of trimetallic Al@Al2O3@Ag@Au and Al@Al2O3@AuAg nanostructures

Bimetallic and trimetallic nanoparticles have attracted significant attention in recent times due to their enhanced electrochemical and catalytic properties compared to monometallic nanoparticles. The numerical calculations using Mie theory has been carried out for three-layered metal nanoshell dielectric–metal–metal (DMM) system consisting of a particle with a dielectric core (Al@Al₂O₃), a middle metal Ag (Au) layer and an outer metal Au (Ag) shell. The results have been interpreted using plasmon hybridization theory. We have also prepared Al@Al₂O₃@Ag@Au and Al@Al₂O₃@AgAu triple-layered core–shell or alloy nanostructure by two-step laser ablation method and compared with calculated results. The synthesis involves temporal separations of Al, Ag, and Au deposition for step-by-step formation of triple-layered core–shell structure. To form Al@Ag nanoparticles, we ablated silver for 40 min in aluminium nanoparticle colloidal solution. As aluminium oxidizes easily in water to form alumina, the resulting structure is core–shell Al@Al₂O₃. The Al@Al₂O₃ particle acts as a seed for the incoming energetic silver particles for multilayered Al@Al₂O₃@Ag nanoparticles is formed. The silver target was then replaced by gold target and ablation was carried out for different ablation time using different laser energy for generation of Al@Al₂O₃@Ag@Au core–shell or Al@Al₂O₃@AgAu alloy. The formation of core–shell and alloy nanostructure was confirmed by UV–visible spectroscopy. The absorption spectra show shift in plasmon resonance peak of silver to gold in the range 400–520 nm with increasing ablation time suggesting formation of Ag–Au alloy in the presence of alumina particles in the solution.