等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

Synthesis and characterization of PbS nanotubes in bicontinuous microemulsion system

PbS nanotubes were successfully synthesized in bicontinuous microemulsion system containing cyclohexane, aqueous solution, n-pentanol and surfactant OP (polyethylene glycol p-octylphenyl ether). The morphology of PbS nanotubes was confirmed by the transmission electron microscopy. The crystallinity and structural features of PbS nanotubes were characterized by powder X-ray diffraction. The effect of key parameters, such as the molar ratio of water to surfactant and the reactant concentration, on the resulting product has also been investigated. The formation mechanism of PbS nanotubes and nanowires synthesized in bicontinuous microemulsion system has been discussed.     

Fabrication of PbS Nanoparticles Embedded in Silica Gel by Reverse Micelles and Sol-Gel Routes

PbS doped-silica gels showing a visible absorption onset were prepared by the sol-gel method. PbS nanoparticles with strong quantum-confinement effect were obtained from sodium sulfide and lead nitrate by the reverse micelle method. Chemical parameters such as the water/surfactant and the [Pb²⁺]/[S²⁻] ratios play a very important role in the PbS particle size and in their absorption threshold. The PbS nanoparticles were dispersed in a hydrolyzed solution of TEOS and converted to homogeneous gels after heating. The absorption threshold of PbS doped-gel is blue shifted compared to the one of the as-prepared PbS particles. The non-linear optical properties of the PbS nanoparticle solution were measured by degenerate four-wave mixing and theX ⁽³⁾ value was estimated to be 1.95 10⁻¹¹ esu.     

Fabrication of PbS nanocrystal-sensitized ultrafine TiO2 nanotubes for efficient and unusual broadband-light-driven hydrogen production

It is highly desired to maximize the use of solar light by developing broadband-light-responsive H₂ production system in the field of photocatalysis. Herein, a novel PbS/(Pt–TiO₂) nanocomposite with efficient and unusual broadband-light-driven H₂ production feature is constructed by using infrared-bandgap PbS nanocrystals as sensitizer of Pt-loaded ultrafine anatase TiO₂ nanotubes (Pt–TiO₂). After optimizing the component ratio, the resultant PbS/(Pt–TiO₂) nanocomposite delivers a H₂ production activity of 813 and 186 μmol h^?1 under ultraviolet (UV)-visible (Vis)-near-infrared (NIR) and Vis-NIR light irradiation, respectively. Moreover, an apparent quantum yield of 38.6%, 26.2%, 2.43%, 3.21%, 2.17%, 0.36%, 0.11% and 0.01% can be attained from the PbS/(Pt–TiO₂) nanocomposite illuminated at 350, 420, 550, 700, 760, 850, 950 and 1064 nm monochromatic light, respectively. The intimate interfacial contacts in the PbS nanocrystals decorated ultrafine TiO₂ nanotubes, which serve as the support and electron acceptor of PbS nanocrystals, can effectively promote the photoexcited hot electrons transferring from PbS nanocrystals to TiO₂ nanotubes before the thermalization losses, and thus causing the efficient Vis-NIR-light-responsive H₂ production activity of the PbS/(Pt–TiO₂) nanocomposite. These results provide an intriguing application of infrared-bandgap materials to exploit the low-energy photons of the solar light for constructing efficient and unusual broadband-responsive H₂ production system.     

Synthesis and characterization of PbS nanorods in W/O microemulsion system

PbS nanorods have been successfully synthesized in water-in-oil (W/O) microemulsion containing non-ionic surfactant OP, n-pentanol, cyclohexane, and aqueous solution. The effects of the molar ratio of water to surfactant (ω₀), the concentration of reactants and the ageing time on the morphologies of PbS nanoparticles were investigated. The microstructures, morphologies and properties of the synthesized products were characterized by means of X-ray diffraction, transmission electron microscopy, and ultraviolet-visible (UV-VIS) absorption spectroscopy, respectively. The results showed that the synthesized rod-like products are composed of cubic phase PbS. These nanorods have an average diameter of about 100 nm, and an average length of about 500 nm. In the UV-VIS absorption spectrum, the absorption edge of PbS nanorods exhibit a blue shift compared with that of bulk PbS, indicating the quantum confinement effect of PbS nano-particles     

Melamine as an Effective Supramolecular Modifier and Stabilizer in a Nanotube‐Constituted Supergel

Self‐assembly of N‐fluorenyl‐9‐methoxycarbonyl glutamic acid (Fmoc‐Glu) in water generates metastable single‐wall nanotubes. These nanotubes entangle and bundle together to form unstable gels that shrink with time and finally result in lamellar crystalline precipitates. Melamine (Mm) was employed as a supramolecular modifier and stabilizer to improve the stability of the nanotubes. Mm interacts with the carboxyl‐rich surfaces of the nanotubes via H‐bonds and static electronic forces to diminish the high affinity of individual nanotubes and facilitate Fmoc‐Glu supergelation (critical gelation concentration <0.1 wt %). Although the basic process of nanotube formation is not disturbed, Mm inverts the supramolecular helicity of nanotubes from P to M.     

Controlled Synthesis of Hollow PbS‐TiO2 Hybrid Structures through an Ion Adsorption–Heating Process and their Photocatalytic Activity

Hollow hybrid nanostructures have received significant attention because of their unique structural features. This study reports a facile ion adsorption–heating method to fabricate hollow PbS‐TiO₂ hybrid particles. In this method, the TiO₂ spheres used as a substrate material to grow PbS are aggregates of many small amorphous TiO₂ particles, and each small particle is covered with thioglycolic acid ligands through Ti⁴⁺–carboxyl coordination. When Pb²⁺ ions are added to a colloidal solution of these TiO₂ spheres, these ions are adsorbed by sulfhydryl (‐SH) groups to form metal thiolates, and the C−S bond is dissociated by heating to release S²⁻. The S²⁻ ions react with Pb²⁺ ions to form PbS without additive sulfur sources. Additionally, the amorphous TiO₂ spheres are transformed into the anatase phase during the heating process. As a result, the crystallization of TiO₂ spheres along with the formation of PbS is simultaneously carried out by heating. During the heating process, owing to the Kirkendall effect of S²⁻ diffusion and the Ostwald ripening effect of the crystallization of amorphous TiO₂ spheres, PbS‐TiO₂ hollow hybrid structures can be obtained. The XRD and XPS characterizations proved the formation of anatase TiO₂ and PbS. The TEM characterization confirmed the formation of hollow structures in the PbS‐TiO₂ hybrid sample. The photocatalytic activity of the hollow PbS‐TiO₂ hybrid spheres have been investigated for the degradation of Cr⁶⁺ under visible light. The results show that hollow PbS‐TiO₂ hybrid spheres exhibited the highest photocatalytic activity, in which almost all the Cr⁶⁺ was degraded after 140 min.     

Electrochemical intercalation reaction of lithium into sulfides of nonlayer structure: I. Lithium intercalation in lead sulfide

The reaction mechanism of cell Li/PbS has been studied with coulombic titration, cyclic voltammetry and X-ray diffraction methods. It was found that in the first stage of discharge (0< y ≤1.5), the intercalation of lithium into lead sulfide took place. The X-ray diffraction patterns showed that the main crystalline structure of PbS remained unchanged after lithiation, and the lithium intercalated probably locates in the center of the cubic-interspace of the crystal. The intercalation free energy of Li into PbS forming LiPbS was found to be ?300.48 KJ·mol^?1 (at 25°C). The chemical diffusion coefficient of lithium in Li_yPbS (0<y≤1) was determined by electrochemical method to be about 10^?11 cm²S-1.     

The effect of PbS nanoparticles on the formation of PbSe in aqueous solutions of sodium selenosulfate and lead(II)

It was established that PbS nanoparticles significantly increase the rate of formation of lead selenide during the reaction of Pb(NO₃)₂ and Na₂SeSO₃ in aqueous solutions of polymers. It was shown that the reaction product consists of PbS/PbSe nanoparticles with a “PbS core-PbSe shell” structure. A correlation was found between the forbidden band widths of the PbS nanoparticles and the PbS/PbSe nanostructures formed during the reaction. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 6, pp. 339–344, November–December, 2006.     

Chemical Synthesis,Structure Characterization,and Optical Properties of Hollow PbSx–Solid Au Heterodimer Nanostructures

Heterodimer nanostructures have attracted extensive attention, owing to an increasing degree of complexity, functionality, and then importance. So far, all the reported ones are built from solid nanoparticles. Herein, nearly monodisperse heterodimer nanostructures are constructed by hollow PbS_x and solid Au domains simultaneously through a mild reaction between PbS nanocrystals and the gold species in the presence of dodecylamine. Control experiments clearly reveal the underlying formation mechanism of the hollow PbS_x–solid Au heterodimers. The Au^III species in the solution, lead to the etching of PbS nanocrystals and the Au^I species facilitate the control of the number of gold domains per nanoparticle. Dodecylamine molecules not only work as a stabilizer in the reaction, but also act as a reducing agent that could greatly affect the morphology of the product. The optical properties of the heterodimers are investigated based on UV/Vis absorption spectroscopy and Raman spectroscopy. This novel heterodimer nanostructure pushes the development of complex nanocrystal‐based architectures forward, and also provides many opportunities for potential applications.     

Lanthanide‐Based Functional Misfit‐Layered Nanotubes

The synthesis of nanotubes from layered compounds has generated substantial scientific interest. “Misfit” layered compounds (MLCs) of the general formula [(MX)_1+x]_m[TX₂]_n, where M can include Pb, Sb, rare earths; T=Cr, Nb, and X=S, Se can form layered structures, even though each sub‐system alone is not necessarily a layered or a stable compound. A simple chemical method is used to synthesize these complex nanotubes from lanthanide‐based misfit compounds. Quaternary nanotubular structures formed by partial substitution of the lanthanide atom in nanotubes by other elements are also confirmed. The driving force and mechanism of formation of these nanotubes is investigated by systematic temperature and time‐dependent studies. A stress‐inducement mechanism is proposed to explain the formation of the nanotubes. The resulting materials may find applications in fields that include thermoelectrics, light emitters, and catalysis and address fundamental physical issues in low dimensions.