Effects of cellulose nanocrystals on the vulcanization of natural rubber/cellulose nanocrystals nanocomposite and corresponding regulating strategies

Vulcanization is a vital process in rubber processing, it endows rubber with valuable physical and mechanical properties, making rubber a widely used engineering material. In addition to vulcanization agent, reinforcing fillers play a non-ignorable influence on the vulcanization of rubber nanocomposites. Herein, the effects of cellulose nanocrystals (CNCs) on the vulcanization of natural rubber (NR)/CNCs nanocomposite was studied. It was found that even though the addition of CNCs can effectively improve the dispersion of ZnO in NR matrix, the vulcanization of NR was inhibited. This may be attributed to the CNCs' adsorption of vulcanizing agents (DM, ZnO) and the acidic chemical environment on the surface of CNCs. In order to improve the vulcanization properties of NR/CNCs nanocomposite, tetramethyldithiochloram (TMTD) and triethanolamine (TEOA) were used as a combination accelerator and curing activator, respectively, and polyethylene glycol (PEG) was introduced to screen hydroxyl groups on the surface of CNCs to prohibit the CNCs' adsorption of vulcanizing agents. The results indicate that TMTD and TEOA effectively improved the vulcanization rate of NR/CNCs nanocomposite and increased the crosslink density by an order of magnitude. Subsequently, the tensile strength, tear strength, and so forth. of NR/CNCs nanocomposite were significantly improved. However, PEG hardly help to improve the vulcanization properties of NR/CNCs nanocomposite. In addition, the control samples without CNCs were prepared and characterized, the comparation between NR and NR/CNCs nanocomposite shows that the synergistic effect of crosslink density and CNCs' reinforcement more effectively improve mechanical properties of NR. This work not only elucidates the inhibiting mechanisms of CNCs on the vulcanization of NR, but also provides practical strategies for improving the vulcanization and properties of NR/CNCs nanocomposite. It may accelerate the application of CNCs as rubber reinforcing filler.     

Rheological,mechanical and morphological properties of thermoplastic vulcanizates based on NR‐g‐PMMA/PMMA blends

Graft copolymer of natural rubber and poly(methyl methacrylate) (NR‐g‐PMMA) was prepared using semi‐batch emulsion polymerization technique via bipolar redox initiation system. It was found that the grafted PMMA increased with the increase of methyl methacrylate (MMA) concentration used in the graft copolymerization. The NR‐g‐PMMA was later used to prepare thermoplastic vulcanizates (TPVs) by blending with PMMA through dynamic vulcanization technique. Conventional vulcanization (CV) and efficient sulphur vulcanization (EV) systems were studied. It was found that the CV system provided polymer melt with lower shear stress and viscosity at a given shear rate. This causes ease of processability of the TPVs via extrusion and injection molding processes. Furthermore, the TPVs with the CV system showed higher ultimate tensile strength and elongation. The results correspond to the morphological properties of the TPVs. That is, finer dispersion of the small vulcanized rubber particles were observed in the PMMA matrix. Various blend ratios of the NR‐g‐PMMA/PMMA blends using various types of NR‐g‐PMMA (i.e. prepared using various percentage molar ratios of NR and MMA) were later studied via dynamic vulcanization by a conventional sulphur vulcanization system. It was found that increasing the level of PMMA caused increasing trend of the tensile strength and hardness properties but decreasing level of elongation properties. Increasing level of the grafted PMMA in NR molecules showed the same trend of mechanical properties as in the case of increasing concentration of PMMA used as a blend component. From morphological studies, two phase morphologies were observed with a continuous PMMA phase and dispersed elastomeric phase. It was also found that more finely dispersed elastomeric phase was obtained with increasing the grafted PMMA in the NR molecules. Copyright © 2005 John Wiley & Sons, Ltd.     

反式丁戊橡胶改性航空轮胎侧胶的结构与性能

采用反式-1,4-丁二烯-异戊二烯共聚橡胶（简称反式丁戊橡胶,TBIR）改性航空轮胎侧胶[天然橡胶（NR）/顺丁橡胶（BR）（质量比80/20）],研究了NR/BR/TBIR混炼胶的结晶行为、力学性能、硫化特性及硫化胶的物理机械性能、动态力学性能和填料分散性.结果表明,相比NR/BR并用胶,结晶性TBIR的并用赋予NR/BR/TBIR混炼胶较高的格林强度和杨氏模量.NR/BR/TBIR混炼胶工艺正硫化时间延长,交联密度提高.TBIR用量范围内,NR/BR/TBIR硫化胶300%定伸应力提高7%,耐屈挠疲劳性能提高35%~50%,滚动阻力降低.m（NR）/m（BR）/m（TBIR）为80/10/10硫化胶具有更好的综合力学性能及耐热氧老化性能.随着硫化时间的延长,NR/BR/TBIR（80/10/10）硫化胶较NR/BR（80/20）硫化胶100%定伸应力提高18%以上,NR/BR体系的耐屈挠疲劳性降低近60%,而NR/BR/TBIR（80/10/10）体系仍能保持原来的50%;反映滚动阻力的60℃损耗因子降低8%~14%,反映抗湿滑性的0℃损耗因子保持不变.填料分散度得到改善,填料聚集体尺寸降低.NR/BR/TBIR（80/10/10）硫化胶具有更好的耐长时间硫化的特性.     

Reactive compatibilization of recycled low density polyethylene/butadiene rubber blends during dynamic vulcanization

For reactive compatibilization of the recycled LDPE with butadiene rubber (BR) an equal quantity of few couples of reactive polyethylene copolymer/reactive polybutadiene (1/1) were introduced into the corresponding phases before the dynamic vulcanization. The LDPE/BR thermoplastic dynamic vulcanizates (TDVs) produced using the poly(ethylene-co-acrylic acid), PE-AA/polybutadiene terminated with isocyanate groups, PB-NCO compatibilizing couple with different ratio of functional groups have demonstrated the best mechanical properties and have been characterized by X-Ray analysis and DMTA measurements. For all of systems studied the increasing components compatibility due to the formation of the essential interface layer have been observed. The PB-NCO modifier participates in two processes: it is co-vulcanised with BR in rubber phase and reacts in the interface with the PE-AA dissolved in LDPE. The amorphous phase of LDPE is dissolved by rubber phase, i.e. the morphology with dual phase continuity is formed that provides an improvement of mechanical characteristics of material obtained. The best combination of mechanical characteristics was obtained for LDPE(PE-AA)/BR(PB-NCO), PB-NCO=7.5 wt.% per PB, COOH/NCO=1/1. The tensile strength and an elongation at break for these blends were 3.9 MPa and 353% and for the basic non-compatibilized blend 3.2 MPa and 217%, relatively.     

Ribbon-like microfiber of vulcanized and non-vulcanized natural rubber obtained by the solution blow spinning

Natural rubber (NR) microfibers were obtained from NR/chloroform solutions with or without vulcanization agents, by a solution blow spinning (SBS) technique. The microfibers showed a ribbon-like morphology with average widths ranging from 15 to 45 μm, depending on the processing conditions. Concentrations of 3%, 4%, and 5% (wt/vol) of NR/chloroform were compared; at 4% wt/vol the spinning process was most stable, and fiber width was the most homogeneous. Microfibrous NR membranes incorporating vulcanizing agents were treated at temperatures of 70, 80, and 90°C for 1, 2, 3, and 4 h. Membrane tensile strength and elongation at break varied with temperature and treatment time. The best result was found with the sample treated at 90°C for 3 h. In this case, the tensile strength and elongation at break was (4.9 ± 0.8) MPa and (867 ± 18) % which is about 310% and 330% higher than the values found for the same sample without the incorporation of vulcanizing agents. This expressive increase was attributed to the vulcanization of the rubber, which also provided a shift to a higher value of the glass transition temperature. Overall properties of the blow-spun films, especially the high elasticity-contraction, suggest they are attractive candidates for use in robotics, and biobased electronics including wearable sensors.     

Studies on radiation grafting of methyl methacrylate onto natural rubber for improving modulus of latex film

Methyl methacrylate (MMA) can be grafted onto natural rubber (NR) in latex by gamma irradiation for improving the mechanical properties of the dry films. Physical blending of MMA-grafted NR latex with radiation vulcanized natural rubber latex (RVNRL) or simultaneous radiation grafting and crosslinking are found to be useful techniques for improving the properties of latex films. Moduli of the films are improved with increasing MMA content; however, tensile strength is reduced. High modulus without much reduction in tensile strength can be achieved if the MMA content is 50–60 parts per hundred rubber.     

反式异戊橡胶合金改性溶聚丁苯橡胶/顺丁橡胶轿车胎面胶

研究了反式异戊橡胶合金(TPIR)的结晶性能、加工性能和力学性能及在轿车胎面胶溶聚丁苯橡胶/顺丁橡胶(SSBR/BR)中的应用.研究结果表明,与无定形SSBR和BR相比,TPIR生胶具有常温可结晶性,因此TPIR具有较高的格林强度.毛细管挤出行为研究结果表明,TPIR具有优异的挤出性能,挤出物外观光滑,挤出涨大比小.与SSBR/BR混炼胶相比,用TPIR改性后的SSBR/BR/TPIR混炼胶的格林强度与100%定伸应力随TPIR含量的增加而提高.经150℃硫化反应后制备的SSBR/BR/TPIR硫化胶物理机械性能优异:不仅耐湿滑性能、耐磨耗性能及压缩强度较对比胶提高,其伸张疲劳性能较对比胶提高4倍以上.透射电子显微镜(TEM)及填料分散仪表征结果表明,与SSBR/BR硫化胶相比,SSBR/BR/TPIR硫化胶的填料聚集体平均尺寸降低2μm,填料分散性显著改善.表明TPIR是一种应用于高性能轿车胎面胶的理想胶料.     

Surface Modification of Rice Husk Ash by Ethanol-assisted Milling to Reinforce the Properties of Natural Rubber/Butadiene Rubber Composites

Rice husk ash(RHA), obtained by pyrolysis of rice husks, can be used as a potential reinforcing filler for rubber composites. In this work, ball milling in ethanol(ethanol-assisted milling) was used to hydroxylate the surface of RHA, promoting the graft modification of bis-(γ-triethoxysilylpropyl)-tetrasulfide(Si69). The obtained modified RHA(RHA-EM-Si69) was filled into the natural rubber/butadiene rubber(NR/BR) composites, and the filler-rubber interactions were enhanced. In consequence, RHA-EM-Si69 filled NR/BR composites showed overall improvement in the mechanical properties compared with RHA filled NR/BR composites. The tear strength increased from 13.37 kN/m to 34.71 kN/m, and the tensile strength increased from 1.84 MPa to 7.75 MPa. Carbon black(N774) was also used for comparison under the same conditions. This method provides a potential for promoting the value of RHA in rubber industry.     

POSS nanoparticles as a potential compatibilizer for natural rubber/butadiene rubber blends

In this study, it was aimed to investigate octavinyl‐polyhedral oligomeric silsesquioxane (OV‐POSS) incorporation into natural rubber (NR)/butadiene rubber (BR) elastomer blends as a potential compatibilizer. The effects of OV‐POSS loading levels on the thermal, mechanical, morphological, and dynamic‐mechanical properties of elastomer blends were explored. Fourier‐Transform Infrared Spectrometer (FTIR), Temperature Scanning Stress Relaxation (TSSR), and Differential Scanning Calorimetry (DSC) results revealed the conceivable effect of OV‐POSS nanoparticles in the vulcanization through reacting with sulfur and/or elastomers. Scanning Electron Microscope (SEM), X‐Ray Diffraction (XRD), and tensile test measurements supported the improvement of mechanical properties due to homogeneous dispersion at low loading levels. On the other hand, high amount of OV‐POSS incorporation (7 and 10 phr) resulted in a decrease in mechanical properties, owing to the agglomeration of nanoparticles. According to contact angle and Dynamic mechanical analysis (DMA) results, it could be concluded that OV‐POSS nanoparticles were localized at the interface of the elastomers and enabled the compatibilization of immiscible NR/BR blends.     

The sensitizing effect of acrylates on radiation vulcanization of natural rubber latex

The sensitizing effect of acrylates on radiation vulcanization of natural rubber latex was studied. The results indicate that Gc value of crosslinking (Gc) will be higher at the same radiation dose when a sensitizer exists, and Gc value decreases with the increase of radiation dose (D) conforming to the formula Gc=KD^-α, where K and α are constants depending on sensitizers. The more sensitizers added, the greater the Gc value. However, the viscosity of the natural rubber latex also increases rapidly along with the increase of sensitizers added.Some sensitizers, such as TMPTA, can decrease the optimum dose from about 200 kGy to approximately 20 kGy according to our experiment. The tensile strength of the film can reach round 20 MPa. Other physical properties are comparable to those of unsensitized.     

Maleic-anhydride grafted EPM as compatibilising agent in NR/BR/EPDM blends

Incorporation of approximately 30 phr Ethylene-Propylene-Diene rubber (EPDM) into natural rubber (NR)/butadiene rubber (BR) is a means to achieve non-staining ozone resistance for tire sidewall applications. However, due to incompatibility of the elastomers and heterogeneous filler distribution in each of the rubber phases, the mechanical properties deteriorate. In the present work, maleic-anhydride modified EPM (MAH-EPM) is added as a compatibilising agent between NR/BR and EPDM. The addition of 5 phr of MAH-EPM results in significantly improved tensile and tear strength when compared to a straight NR/BR/EPDM blend. These improvements can mainly be attributed to a compatibilising effect of MAH-EPM, resulting in a more homogeneous phase distribution, but in particular a much better homogeneous carbon black distribution over the different rubber phases. In addition, ionic crosslinks are introduced into the blends by interaction of MAH-EPM with zinc oxide.     

Dynamically vulcanized ethylene propylene diene terpolymer/nylon thermoplastic elastomers

A thermoplastic elastomer (TPE) of ethylene propylene diene terpolymer (EPDM) and nylon with excellent mechanical properties was prepared by dynamic vulcanization. The effects of the curing systems, compatibilizer, nylon content and reprocessing on the mechanical properties of EPDM/nylon TPEs were investigated in detail. Experimental results indicate that maleic anhydride (MAH) grafted EPR has a better performance in compatibilizing the EPDM/nylon blends compared with other compatibilizers containing acid group. Tensile strength and elongation at break go through a maximum value at a compatibilizer resin content (on total rubber dosage) of 20%. EPDM/nylon TPE using sulfur as curative has higher tensile strength and elongation than that of TPE using phenolic resin or peroxide as curatives. Tensile strength and elongation at break increase with increasing nylon content. Scanning electron microscopy results show that rubber particles distributed at an average size of 1 μm in dynamic vulcanized EPDM/MAH-g-EPR/nylon TPE.     

原位接枝炭黑/天然橡胶复合材料的制备及性能

采用原位固相接枝方法,使在高温和强剪切作用下降解的天然橡胶接枝到炭黑表面.通过对接枝前后炭黑填充天然橡胶的性能对比发现,原位接枝炭黑不但能提高天然橡胶的硫化速度,还能提高拉伸强度,定伸应力和撕裂强度等;动态力学性能的测试结果表明接枝炭黑填充的天然橡胶中接枝炭黑网络化程度较低,这些结果主要归因于接枝炭黑在橡胶基体中分散性的改善及炭黑与橡胶之间作用力的增加.     

Dynamic vulcanization of reclaimed tire rubber and high density polyethylene blends

Dynamic vulcanization of reclaimed tire rubber (RTR) and HDPE blends was reported. The effect of blend ratio, methods of vulcanization, i.e. sulphur, peroxide, and mixed system and the addition of compatibilizer on mechanical, thermal, and rheological properties were investigated. The blend with highest impact strength was obtained from 50/50 RTR/HDPE vulcanized by sulphur. Increasing the RTR content to more than 50% resulted in a decrease in the impact strength of blend, most likely due to the increasing carbon black content. For tensile strength, the presence of rubber and carbon black, however, unavoidably caused a drop in this property. Comparing among three methods of vulcanization, sulphur system seems to be the most effective method. Results from solvent swelling ratio, glass transition temperatures and viscosity indicated that the sulphur vulcanization created the highest degree of cross-link and filler-matrix interaction in the RTR/HDPE blend. Morphology of the blends was also assessed by scanning electron microscopy (SEM).     

Radiation Vulcanization of Nitrile Butadiene Rubber/Butadiene Rubber Blends

Blends of nitrile butadiene rubber (NBR) with butadiene rubber (BR) with varying ratios have been prepared. Vulcanization of prepared blends has been induced by ionizing radiation of gamma rays with varying dose up to 250 kGy. Physical properties, namely soluble fraction and swelling number have been followed up using toluene as a solvent. Mechanical properties, namely tensile strength, tensile modulus at 100% elongation and elongation at break have been followed up as a function of irradiation dose, as well as blend composition. Thermal stability of blends was studied by TGA. The result indicated that the addition of NBR has improved the properties of NBR/BR blends. Also, NBR/BR blend is thermally stable than BR alone.     

聚丙烯／顺丁橡胶动态硫化增韧的研究

研究了在聚丙烯(pp)与顺丁橡胶(BR)共混过程中加入橡胶硫化剂使共混体系中橡胶相动态硫化交联。研究结果表明,采用动态硫化法可提高共混物的冲击强度和拉伸强度。借助于SEM和DMA,证实了动态硫化使PP/BR共混体系具有相界面粘结良好的多相结构,改善了两相相容性。探讨了动态硫化增韧的机理。     

Radiation effect on properties of carbon black filled NBR/EPDM rubber blends

Rubber blend of acrylonitrile butadiene rubber (NBR) and ethylene-propylene diene monomer (EPDM) rubber (50/50) has been loaded with increasing contents, up to 100 phr, of reinforcing filler, namely, high abrasion furnace (HAF) carbon black. Prepared composites have been subjected to gamma radiation doses up to 250 kGy to induce radiation vulcanization under atmospheric conditions. Mechanical properties, namely, tensile strength (TS), tensile modulus at 100% elongation (M₁₀₀), and hardness have been followed up as a function of irradiation dose and degree of loading with filler. On the other hand, variation of the swelling number as a physical property, as a function of same parameters, however, in car oil as well as brake oil has been undertaken. In addition, the electrical properties of prepared composites, namely, their electrical conductivity, were also evaluated. The thermal behavior of the prepared composites was also investigated. The results obtained indicate that improvement has been attained in different properties of loaded NBR/EPDM composites with respect to unloaded ones.     

Influence of different curing systems on the physico-mechanical properties and stability of SBR and NR rubbers

The physical properties of radiation, sulfur and peroxide-cured styrene–butadiene rubber (SBR) and natural rubber (NR) were compared. The dependence of the mechanical properties of the radiation-vulcanized SBR and NR on the coagent concentration and radiation dose was studied. The effect of thermal aging on the mechanical properties of the different rubber formulations was discussed. The radiation-cured formulations of SBR have superior mechanical properties and thermal stability compared with those of the chemically vulcanized compounds. Whereas, the radiation-cured formulations of NR have similar mechanical properties but superior thermal stability (based on the % change in E after thermal aging), when compared with those of the sulfur-vulcanized compounds and slightly better than those of the peroxide-vulcanized compounds.     

Thermal stability and ageing properties of sulphur and gamma radiation vulcanized natural rubber (NR) and carboxylated styrene butadiene rubber (XSBR) latices and their blends

The thermal stability of natural rubber (NR) and carboxylated styrene butadiene rubber (XSBR) latices and their blends was studied by thermogravimetric methods. Ageing characteristics of these latex blends were studied by applying hot air oven thermal ageing for seven days at 70 °C. The mechanical properties of the aged samples were studied. Thermal degradation and ageing properties of these individual latices and their blends were investigated with special reference to blend ratio and vulcanization techniques. As the XSBR content in the blends increased their thermal stability was also found to increase. Among sulphur and radiation-vulcanized samples, radiation cured possesses higher thermal stability due to the higher thermal stability of carbon-carbon crosslinks. DTG curves were used for the determination of different stages involved in the degradation. Activation energy for degradation was determined from Coats-Redfern plot. The properties of aged samples were found to decrease due to chain depletion. However, the moduli of XSBR and NR/XSBR blends were found to increase owing to the formation of crosslinks upon ageing.