共查询到20条相似文献,搜索用时 15 毫秒
1.
利用波段内连续激光, 辐照禁带宽度为0.33 eV的中波光伏碲镉汞探测器. 实验结果表明, 随着辐照激光光强的逐渐增大, 探测器从线性响应过渡为非线性响应. 当探测器进入非线性状态, 探测器的开路电压随激光光强的增大而减小, 且在激光开启辐照时开路电压信号迅速下跳, 在激光停止辐照时开路电压信号迅速上跳. 通过考虑激光辐照下探测器的温度场分布以及温度对p-n结内建电场的影响, 结合考虑机械快门在开启和关闭时对激光光强变化的影响, 建立了光伏探测器在波段内连续激光辐照下的解析模型, 模型计算结果与实验结果吻合得较好. 研究表明, 激光辐照过程中的非线性响应, 主要由温度对p-n结内建电场的影响决定, 激光开启和关闭时的开路电压的幅值是由光强和温度共同决定. 相似文献
2.
利用三维经典系综模型,研究了整个系综两电子(Ar原子为例)从激光场吸收的能量对激光参数(波长、激光强度和椭偏率)的依赖关系.结果显示,当激光强度固定,波长增加时,整个系综两电子从激光场吸收的能量整体呈上升趋势,但不同强度下趋势略有差异.在较低强度时整个系综两电子从激光场吸收的能量对波长的依赖关系呈现持续平稳增加的趋势,在较高强度时呈现先缓慢减小再快速增大的趋势.对强度的依赖关系在不同波长时呈现两个有趣的交叉点.对椭偏率的依赖关系在较低强度时呈现先逐渐减小再缓慢增大的趋势;在中等强度时呈现一个“阶梯型”即先缓慢增大再逐渐减小最后缓慢增大;在更高强度时呈现先逐渐增大再逐渐减小的趋势.为了解释整个系综两电子从激光场吸收的能量对激光参数的依赖关系,把整个系综的动力学过程分为双电离、单电离、受挫单电离和受挫双电离4种通道.然后分析各个通道的特征及其如何主导整个系综两电子从激光场吸收的能量的变化趋势.分析结果表明,整个系综两电子从激光场吸收的能量对波长、激光强度和椭偏率的依赖均是由于某种通道主导整个系综两电子从激光场吸收的能量的结果. 相似文献
3.
4.
开展了多波段激光(750~970 nm)对彩色CCD成像系统的外场干扰实验,测得了不同辐照条件下对外场1.3 km处彩色CCD成像系统的干扰效果;建立了彩色CCD相机的激光干扰模型,对实验结果进行了理论验证与分析。理论与实验结果表明:强激光对彩色CCD成像系统的干扰效果明显,CCD靶面出现了明显的光饱和和串扰现象,光饱和区域的形成是由激光束进入光学系统后发生衍射效应造成的;到靶激光功率密度越强,CCD靶面光饱和面积越大,激光干扰效果越好;单波段750 nm激光作用下,到靶功率密度为4.2 kW/cm2,CCD靶面的光饱和面积为0.88 mm×0.97 mm;多波段激光(750~970 nm)作用下,到靶功率密度为20.7 kW/cm2,CCD靶面发生全靶面饱和现象;仿真结果与实验结果基本一致,证明了理论模型的正确性。对远场干扰能力计算结果表明:随着干扰距离的增加,到靶功率密度减小,激光干扰效果变差。 相似文献
5.
脉冲激光束在低真空(约2 Pa)环境下聚焦到高纯Zn靶表面, 烧蚀区域不仅有中心深孔的宏观损伤, 而且还发现大量微米量级的类似足球形状的金属Zn球体结构附着生长在孔洞内侧表面. 实验过程中采用等离子体光谱诊断技术研究宏观和微观损伤对后续脉冲激光的影响程度. 与聚焦于金属Zn平滑表面相比, 宏观损伤可以使后续激光诱导的Zn原子334.5 nm谱线强度提高10.3%, 在此基础上大量Zn微米球体附着在内表面可以使谱线强度再提高34.3%. 因此, 推断这些金属Zn微球表面镶嵌着光洁的纳米量级六边形和五边形小平面, 可以对后续脉冲激光产生镜面反射, 使得激光能量汇聚并耦合增强, 提高烧蚀效率. 实验结果还表明, 这些微米球体的数目随着激光脉冲次数的增加而增多, 使得后续激光能够诱导产生更为致密高温的等离子体. 研究结果有望为激光-金属微孔技术提供新思路.
关键词:
脉冲激光烧蚀
微纳米结构
激光诱导等离子体 相似文献
6.
500.8 nmNd∶YAG青光激光器光学薄膜的设计与制备 总被引:5,自引:2,他引:3
从双波长激光运转及和频的机理出发,对LD泵浦Nd∶YAG,LBO腔内和频500.8 nm〖JP2〗青光激光器所使用的光学薄膜进行了设计和制备.在激光反射镜的设计上,为了达到最佳的和频输出,对膜系要求进行了深入分析.采用对谐振腔一端面反射率固定不变并通过对另一腔镜基频光的透射率进行调谐的方法, 在给出合理初始结构后,利用计算机对膜厚进行了优化.并采用双离子束溅射沉积的方法,通过时间监控膜厚法成功制备出青光激光器所使用的全介质激光反射膜, 在室温下实现946 nm和1064 nm双波长连续运转,并通过Ⅰ类临界相位匹配LBO晶体腔内和频在国内首次实现500.8 nm青色激光连续输出.当泵浦注入功率为1.4 W时和频青光最大输出达20 mW. 相似文献
7.
为研究激光冲击对E690高强钢激光熔覆修复层微观组织的影响,选用专用金属粉末对E690高强钢试样预制凹坑进行激光熔覆修复,并使用脉冲激光对激光熔覆层进行冲击强化处理,同时采用扫描电镜、透射电镜和X射线应力分析仪分别对激光冲击前后激光熔覆层的微观组织和表面残余应力进行检测。结果表明:激光熔覆修复后,激光熔覆层组织为等轴晶,熔覆层与E690高强钢基体之间冶金结合良好,其表面残余应力为均匀分布的压应力。经激光冲击后,激光熔覆层截面晶粒得到细化,并观察到大量的形变孪晶,互相平行的孪晶界分割熔覆层粗大晶粒,在激光熔覆层的晶粒细化过程中发挥着重要作用;试样表层位错在{110}滑移面上发生交滑移,在晶界周围形成了位错缠结。经激光冲击后,激光熔覆层冲击区域表面残余压应力数值相较于冲击前提升了1.1倍。 相似文献
8.
采用无模激光器发射波长为330 nm的激光激发多色激光导星,需要考虑脉冲激光重频率、激光带宽、激光初始光斑直径以及大气透过率对回波光子数的影响.通过数值模拟,计算了高斯光束的脉冲激光和连续激光激发多色激光导星在实际大气中后向辐射330 nm和2207 nm波长的回波光子数.数值计算结果表明,在垂直发射和接收的情况下,当到达大气中间层的激光能量为1 W时,连续激光能够获得更多的回波光子数,并且回波光子数几乎无起伏.对于脉冲激光,提高脉冲激光重频率达到50 kHz以上时,多色激光导星330 nm的回波光子数随脉冲重频率的增加趋于有限值;当大气能见度小于5 km且大气相干长度为12.8 cm时,大约需要34 W以上的激光发射能量,才能获得满足使用自然星全倾斜探测的330 nm回波光子数.对于连续激光,相同情况下,大约需要20 W以上的激光发射能量. 相似文献
9.
高重频CO_2激光损伤HgCdTe晶体的数值分析 总被引:1,自引:0,他引:1
针对CO2激光作用下HgCdTe晶体的损伤问题进行了数值分析。首先,建立了高重频CO2激光损伤Hg0.784Cd0.216Te晶体的三维热传导物理模型;然后,利用有限元方法计算了单脉冲和高重频CO2激光作用下,Hg0.784Cd0.216Te晶体的损伤阈值;最后,分析了激光重频以及辐照时间对晶体损伤阈值的影响。研究结果表明:单脉冲激光辐照下,晶体的损伤阈值为64.5 J/cm2;高重频(f>1 kHz)激光辐照下,激光重频的改变对晶体损伤阈值的影响较小,损伤阈值应由平均功率密度表征,且与辐照时间密切相关;辐照时间的增加,可以有效地减小晶体的损伤阈值,当激光辐照功率密度<1.95 kW/cm2时,不会发生晶体损伤。研究结果对高重频CO2激光在激光加工以及激光防护的应用方面具有指导意义。 相似文献
10.
11.
Yuji Utsunomiya Takashi Kajiwara Takashi Nishiyama Kunihito Nagayama Shiro Kubota 《Applied Physics A: Materials Science & Processing》2010,99(3):641-649
We studied a new pulse laser ablation phenomenon on a liquid surface layer, which is caused by the difference between the
refractive indices of the two materials involved. The present study was motivated by our previous study, which showed that
laser ablation can occur at the interface between a transparent material and a gas or liquid medium when the laser pulse is
focused through the transparent material. In this case, the ablation threshold fluence is reduced remarkably. In the present
study, experiments were conducted in water and air in order to confirm this phenomenon for a combination of two fluid media
with different refractive indices. This phenomenon was observed in detail by pulse laser shadowgraphy. A high-resolution film
was used to record the phenomenon with a Nd:YAG pulse laser with 10-ns duration as a light source. The laser ablation phenomenon
on the liquid surface layer caused by a focused Nd:YAG laser pulse with 1064-nm wavelength was found to be followed by the
splashing of the liquid surface, inducing a liquid jet with many ligaments. The liquid jet extension velocity was around 1000
m/s in a typical case. The liquid jet decelerated drastically due to rapid atomization at the tips of the ligaments. The liquid
jet phenomenon was found to depend on the pulse laser parameters such as the laser fluence on the liquid surface, laser energy,
and laser beam pattern. The threshold laser fluence for the generation of a liquid jet was 20 J/cm2. By increasing the incident laser energy with a fixed laser fluence, the laser focused area increased, which eventually led
to an increase in the size of the plasma column. The larger the laser energy, the larger the jet size and the longer the temporal
behavior. The laser beam pattern was found to have significant effects on the liquid jet’s velocity, shape, and history. 相似文献
12.
13.
14.
15.
16.
This paper proposes an innovative vibration testing method based on impulse response excited by laser ablation. In conventional vibration testing using an impulse hammer, high-frequency elements of over tens of kilohertz are barely present in the excitation force. A pulsed high-power YAG laser is used in this study for producing an ideal impulse force on a structural surface. Illuminating a point on a metal with the well-focused YAG laser, laser ablation is caused by generation of plasma on the metal. As a result, an ideal impulse excitation force generated by laser ablation is applied to the point on the structure. Therefore, it is possible to measure high-frequency FRFs due to the laser excitation. A water droplet overlay on the metal is used to adjust the force magnitude of laser excitation. An aluminum block that has nine natural frequencies below 40 kHz is employed as a test piece. The validity of the proposed method is verified by comparing the FRFs of the block obtained by the laser excitation, impulse hammer, and finite element analysis. Furthermore, the relationship between accuracy of FRF measurements and sensitivity of sensors is investigated. 相似文献
17.
Frequency stabilization of a 399-nm laser by modulation transfer spectroscopy in an ytterbium hollow cathode lamp
下载免费PDF全文
![点击此处可从《中国物理 B》网站下载免费的PDF全文](/ch/ext_images/free.gif)
The modulation transfer spectroscopy in an ytterbium hollow cathode lamp at 399 nm is measured. The error signal for frequency locking is optimized by measuring the dependences of its slope, linewidth and magnitude on various parameters. Under the optimum condition, the laser frequency at 399 nm can be stabilized. The long-term stability of laser frequency is measured by monitoring the fluorescence signal of the ytterbium atomic beam induced by the locked laser. The laser frequency is shown to be tightly locked, and the stabilized laser is successfully applied to the cooling of ytterbium atoms. 相似文献
18.
根据红外光学系统的会聚特性,用光学增益方法分析了红外系统中各元件对应的光强分布,确定了位于焦面附近光学元件是激光破坏的易损部件,并提出了强激光对红外系统元件损伤,造成其探测、制导功能失效的硬破坏机理;由红外滤光片、探测器和信号处理电路与入射激光波长的光谱响应分析,提出了弱激光对红外系统干扰,导致其探测、制导功能在激光辐照一段时间内失效的软破坏机理;开展了激光辐照红外系统的失效验证实验,较好地解释了其失效的机理和效应。 相似文献
19.