An experimental design based strategy to optimize a capillary electrophoresis method for the separation of 19 polycyclic aromatic hydrocarbons

Because of their high toxicity, international regulatory institutions recommend monitoring specific polycyclic aromatic hydrocarbons (PAHs) in environmental and food samples. A fast, selective and sensitive method is therefore required for their quantitation in such complex samples. This article deals with the optimization, based on an experimental design strategy, of a cyclodextrin (CD) modified capillary zone electrophoresis separation method for the simultaneous separation of 19 PAHs listed as priority pollutants. First, using a central composite design, the normalized peak-start and peak-end times were modelled as functions of the factors that most affect PAH electrophoretic behavior: the concentrations of the anionic sulfobutylether-β-CD and neutral methyl-β-CD, and the percentage of MeOH in the background electrolyte. Then, to circumvent computational difficulties resulting from the changes in migration order likely to occur while varying experimental conditions, an original approach based on the systematic evaluation of the time intervals between all the possible pairs of peaks was used. Finally, a desirability analysis based on the smallest time interval between two consecutive peaks and on the overall analysis time, allowed us to achieve, for the first time in CE, full resolution of all 19 PAHs in less than 18 min. Using this optimized capillary electrophoresis method, a vegetable oil was successfully analyzed, proving its suitability for real complex sample analysis.     

Determination of trace amounts of polycyclic aromatic hydrocarbons in soil

A method for monitoring the contamination of soil with polycyclic aromatic hydrocarbons (PAHs) is introduced. Drying at elevated temperature is omitted to avoid losses of the more volatile constituents (primarily naphthalene). The soil sample, including its natural water content, is extracted with 2-methoxyethanol and cleaned up using a disposable C₈ cartridge and the PAHs are eluted with pentane, concentrated and measured by capillary gas chromatography with flame ionization detection. Determination limits between 15 and 35μg kg^?1 are obtained and the recovery is 80–90% measured at the 125 μg kg^?1 spike level, except for naphthalene (66%). Special attention is given to the design of the spiking technique, which simulates natural incorporation as far as possible, takes account of evaporation losses and therefore allows “real” recovery rates to be determined.     

Analysis of intermediates from polycyclic aromatic hydrocarbon biodegradation

A major difficulty in assessing bioremediation in hydrocarbon impacted field sites is the determination of the extent and products of contaminant biodegradation. Previously, various analytical techniques, including mass spectrometry and chromatography, have been used to characterize components in mixtures resulting from biodegradation. In this work, the applicability of capillary electrophoresis (CE) to this area of research is demonstrated. CE methods were optimized for analysis of compounds that are known metabolites of polycyclic aromatic hydrocarbon (PAH) biodegradation.     

On-line solid-phase extraction and high performance liquid chromatography determination of polycyclic aromatic hydrocarbons in water using polytetrafluoroethylene capillary

Naphthalene, biphenyl, acenaphtene, anthracene and pyrene were extracted from water samples using inner walls of polytetrafluoroethylene capillary. Optimum conditions for sorption, desorption and heart-cutting of the analyte zone were found. Combined on-line solid-phase extraction and HPLC method for determination of these compounds was proposed. Limits of detection were: (μg L⁻¹): 0.4 (naphthalene), 0.3 (biphenyl), 0.6 (acenaphtene), 0.2 (anthracene) and 0.1 (pyrene).     

Development of a novel ultrasound-assisted surfactant-enhanced emulsification microextraction method and its application to the analysis of eleven polycyclic aromatic hydrocarbons at trace levels in water

A novel ultrasound-assisted surfactant-enhanced emulsification microextraction (UASEME) technique has been proposed by using low-density extraction solvents. In the proposed technique, Tween 80 and cyclohexane were injected into 5-mL glass test tubes with conical bottoms, containing 5.00 mL of a water sample that was located inside the ultrasonic bath. When the extraction process was finished, the glass test tube was sealed with a rubber plug and then placed upside down in a centrifuge. The finely dispersed droplets of cyclohexane collected at the conical bottom of test tube because the density of cyclohexane is less than of water, and the PAHs were concentrated in the cyclohexane. Next, 5 μL of the cyclohexane that collected at the conical bottom was removed using a 10-μL microsyringe and injected into high performance liquid chromatography coupled with fluorescence detection (HPLC-FLD) for analysis. The proposed method avoided the use of chlorinated solvents, which have been widely used as extraction solvents in a normal UASEME assay. Parameters that affected the extraction efficiency, such as the type and volume of the extraction solvent, the type and concentration of the surfactant, and the ultrasound emulsification time and salt addition, were investigated and optimised for the method. Under the optimum conditions, the enrichment factors ranged between 90 and 247. The limits of detection of the method were 0.6-62.5 ng L(-1). Good recoveries and repeatability of the method for the eleven PAHs were also obtained. The proposed UASEME technique has been demonstrated to be simple, practical and environmentally friendly for the determination of PAH residues in real water samples.     

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from gas and particulate phases of atmospheric samples

Pressurised liquid extraction (PLE) was applied to determine the atmospheric levels of 16 polycyclic aromatic hydrocarbons (PAHs) in the gas and particulate phases. The method involved high‐volume air sampling with quartz fibre filters (QFFs) and polyurethane foam (PUF) plugs and analytes were subsequently extracted from the samples by PLE, and determined with GC‐MS. We optimised the PLE conditions for the solvent, the number of cycles and extraction temperature. Recoveries were higher than 90% for most compounds. Method LODs and LOQs were between 0.001 and 0.02 ng/m³ and between 0.01 and 0.05 ng/m³. Air samples were taken from a site in the region of Tarragona in Catalonia, Spain, where one of the largest petrochemical complexes in southern Europe is located. The total concentration of PAHs were from 6.7 to 27.66 ng/m³, with predominant levels of PAHs appearing in the gas phase (48–81%), and an average level of benzo[a]pyrene, the most carcinogenic PAH, of 0.86 ng/m³.     

Comparison of two capillary electrophoresis online stacking modes by analysis of polycyclic aromatic hydrocarbons in airborne particulates

Naphthalene, fluorene, pyrene, anthracene, phenanthrene, and chrysene were successfully separated by CD-modified MEKC (CD-MEKC) using 20 mM borate (pH 9.0) containing 90 mM SDS and 75 mM beta-CD. Two online stacking methods, i.e., sweeping and field-enhanced sample injection (FESI), were explored to enhance the detection sensitivity. The influences of some crucial parameters in sweeping and FESI procedures were investigated. For FESI method, a plug of water and low-conductivity sample matrix was used to increase the stacking efficiency. Compared with the sweeping method, FESI can increase the sensitivity in the range of 10-20-fold. The proposed method was used for the analysis of polycyclic aromatic hydrocarbons in airborne particulates.     

Liquid-liquid-liquid microextraction for the enrichment of polycyclic aromatic hydrocarbon metabolites investigated with fluorescence spectroscopy and capillary electrophoresis

The extraction and pre-concentration of phenol, 2-naphthol, and several hydroxyl polycyclic aromatic hydrocarbon (PAH) metabolites were investigated, using liquid-liquid-liquid microextraction (LLLME). The PAH metabolites are a very important class of compounds, and they have not been investigated previously by LLLME. For several of the hydroxyl PAH metabolites, the enrichment factors were small when using LLLME with an alkaline acceptor phase. Changing the acceptor phase to 1-octanol, which gave a two-phase system, improved the enrichment factors significantly for several of the hydroxyl PAH metabolites. For example, the enrichment factor was improved by a factor of 68.5 for 3-hydroxybenzo[a]pyrene. Enrichment factors were investigated as a function of time and stirring rate. At about 55 min the enrichment factor reached a maximum for the two-phase system and at approximately 75 min for the three-phase microextraction system. However, a 30 min extraction time was used for most of the experiments. Also, fluorescence spectroscopy was used to determine the enrichment factors and the mass distribution of the solute between the phases. Fluorescence spectroscopy was very effective in determining the very small concentrations of the solute in the various phases. In addition, capillary electrophoresis and LLLME were combined to demonstrate the substantial enrichment of 2-naphthol by combining these two approaches.     

Evaluation of polycyclic aromatic hydrocarbons in gasoline by HPLC and GC-MS

Summary In this paper the evaluation of polycyclic aromatic hydrocarbons (PAHs) in gasoline is described. A procedure involving a double extraction of samples with N-methylpirrolidone-water-phosphoric acid and with cyclohexane has been used followed by HPLC-DAD and GC-MS. The results obtained show that all gasoline samples contain PAHs with two to six rings and no substantial difference was noticed between leaded and unleaded gasoline. The benzo(a)-pyrene content ranged between 1.0–2.0 mg L⁻¹, a comparatively high concentration for a dangerous compound.     

Sample preparation of sewage sludge and soil samples for the determination of polycyclic aromatic hydrocarbons based on one-pot microwave-assisted saponification and extraction

A microwave-assisted sample preparation (MASP) procedure was developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) in sewage sludge and soil samples. The procedure involved the simultaneous microwave-assisted extraction of PAHs with n-hexane and the hydrolysis of samples with methanolic potassium hydroxide. Because of the complex nature of the samples, the extracts were submitted to further cleaning with silica and Florisil solid-phase extraction cartridges connected in series. Naphthalene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[e]pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3-cd]pyrene, were considered in the study. Quantification limits obtained for all of these compounds (between 0.4 and 14.8 μg kg⁻¹ dry mass) were well below of the limits recommended in the USA and EU. Overall recovery values ranged from 60 to 100%, with most losses being due to evaporation in the solvent exchange stages of the procedure, although excellent extraction recoveries were obtained. Validation of the accuracy was carried out with BCR-088 (sewage sludge) and BCR-524 (contaminated industrial soil) reference materials.     

Glass capillary column with nematogenic liquid crystals as stationary phases for separating polycyclic aromatic hydrocarbons

Summary Use of the homologues and analogues of nematogenic liquid crystals of the type N,N-bis(p-methoxylbenzylidene)-,-bi-p-toluidine (BMBT) as stationary phases in glass capillary columns is described. These stationary phases are very useful for resolving closely related, rigid solute isomers of three-, four- and five-ring PAH. With these columns it is possible to achieve faster and more complete separation of PAH compared with packed columns with a liquid crystalline stationary phase.     

Use of a keeper to enhance the recovery of volatile polycyclic aromatic hydrocarbons in HPLC analysis

Summary The recorveries of volatile polycyclic aromatic hydrocarbons in HPLC analysis may be enhanced if a long-chain alcohol, e.g. 1-hexanol or 1-octanol, is used as keeper in the solvent-evaporation step. Even under the harsh conditions of the vacuum-concentrator centrifuge, recoveries of more than 90% were achieved for 14 of the 15 PAH tested. The use of liquid-liquid extraction (LLE) eliminates the problem of adsorption of highly condensed aromatics by the wall of the sampling bottle. The combination of LLE with vacuum-controlled rotary evaporation and use of a keeper yielded overall recoveries between 50 and 130%, for most substances close to 100%, from tap water spiked with trace concentrations. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Comparative performance of extraction strategies for polycyclic aromatic hydrocarbons in peats

The assessment of historical trends in atmospheric deposition of organic contaminants by using peat samples has been reported on several occasions because these samples represent an almost ideal medium for recording temporal changes in organic contaminant deposition rates. The determination of polycyclic aromatic hydrocarbons (PAHs) in peat samples is complicated due to the high content of organic matter in peat, which affects both extraction efficiency and analytical quality. A rapid and simple method is proposed for the determination of 10 US Environmental Protection Agency indicator PAHs in complex matrices such as peat. This article reviews and addresses the most relevant analytical methods for determining PAHs in peat. We discuss and critically evaluate three different extraction procedures, such as ultrasound-assisted solvent extraction (UASE), shaking and pressurized liquid extraction (PLE). Clean-up of extracts was performed by solid-phase extraction using silica cartridges. Detection of the selected PAHs was carried out by high-performance liquid chromatography coupled with fluorescence detection for determination. Optimization of the variables affecting extraction by the selected extraction techniques was conducted, concluding that the UASE extraction method using hexane:dichloromethane (80:20) as extractant was robust enough to determine the selected PAHs in peat samples with estimated quantification limits between 0.050 and 3.5 μg/kg depending on the PAH. UASE did not demand sophisticated equipment and long extraction times. PLE involved sophisticated equipment and showed important variations in the results. The method proposed was applied to the determination of PAHs in peat samples from Xistral Mountains (Galicia, Spain).     

Fluidized-bed extraction of polycyclic aromatic hydrocarbons from contaminated soil samples

Summary Due to the carcinogenity and ubiquity of polycyclic aromatic hydrocarbons in the environment they are of ongoing interest to analytical chemistry. In this study, a comparison of the classic Soxhlet extraction and, fluidized-bed extraction, has been conducted. The extraction of polycyclic aromatic hydrocarbons by this technique has been optimized considering as experimental variables the variation of the number of extraction cycles and the holding time after reaching the heating temperature by means of a surface response design. The significance of the operational parameters of the fluidized-bed extraction on the performance characteristics has been investigated. For the determination of the analytes a selective clean-up of the extracts followed by a fast gas chromatography method with mass spectrometric detection was used, resulting in low limits of detection (0.2 pg μL⁻¹). The accuracy of the complete analytical method was established by extraction and analysis of reference materials.     

Water stability of zeolite imidazolate framework 8 and application to porous membrane-protected micro-solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

Zeolite imidazolate framework 8 (ZIF-8) has permanent porosity, high surface area, hydrophobic property, open metal sites and remarkable water stability. These novel properties characterize the material as being different from other moisture sensitive metal-organic frameworks and endow ZIF-8 with the potential to extract trace analytes from environmental water samples. In the present study, ZIF-8 was synthesized and used as a sorbent for micro-solid-phase extraction of 6 polycyclic aromatic hydrocarbons (PAHs) from environmental water samples for the first time. Parameters influencing the extraction efficiency such as desorption time, extraction time, desorption solvent and salt concentration were investigated. Environmental water samples collected from a local lake were processed using this novel μ-SPE procedure. ZIF-8 proved to be a very efficient extraction sorbent for the extraction of trace analytes from water samples. The limits of detection from gas chromatography-mass spectrometric analysis of PAHs were 0.002-0.012 ng/ml. The linear ranges were 0.1-50 or 0.5-50 ng/ml. The relative standard deviations for five replicates of the extractions were in the range of 2.1-8.5%.     

Application of a polysiloxane-based extraction method combined with column liquid chromatography to determine polycyclic aromatic hydrocarbons in environmental samples

Silicone rods with a diameter of 1 mm and 10 mm long were used to extract polycyclic aromatic hydrocarbons (PAHs) from water samples and for the rapid screening of highly contaminated waste material. The rods were placed in a 15 ml glass vial for the extraction of the analytes, which involved shaking (300 min⁻¹) the sample for 3 h. After extraction the rods were placed into 250 μl inserts of 2 ml vials filled with 100 μl of an acetonitrile-water mixture (4:1) and desorption was performed with sonication for 10 min. Then the PAHs were determined using LC and fluorescence detection. Recoveries of the rod extraction ranged between 62 and 97% and the detection limits were between 0.1 and 1.2 ng l⁻¹. These results are comparable with those of stir bar sorptive extraction (SBSE). Although the rods are reusable, their low price means they can be discarded if contaminated, eliminating the need for expensive cleaning. One disadvantage compared to SBSE is the longer extraction time needed to reach equilibrium.     

Improved gas-chromatographic columns of liquid crystals supported on glass beads for analysis of polycyclic aromatic hydrocarbons

Summary Glass microbead columns withN, N-bis-(p-butoxybenzilidene) , -bi-p-toluidine (BBBT) a high-temperature smectic-nematic liquid crystalline stationary phase have been prepared. The best efficiency was obtained with BBBT from 0.025% w/w (ca. 1800 theoretical plates m^–1) to 0.1% w/w (ca. 2100 theoretical plates m^–1). Capacity ratios and separation efficiencies of columns packed with glass microbeads treated and untreated with a surfaceactive agent were studied as a function of analysis time. A separation of five methylchrysene isomers is shown.     

Analytical evaluation of BEA zeolite for the pre-concentration of polycyclic aromatic hydrocarbons and their subsequent chromatographic analysis in water samples

The analytical performance of BEA – a commercial zeolite – is evaluated for the pre-concentration of fifteen Environmental Protection Agency – polycyclic aromatic hydrocarbons and their subsequent HPLC analysis in tap and lake water samples. The pre-concentration factors obtained with BEA have led to a method with excellent analytical figures of merit. One milliliter aliquots were sufficient to obtain excellent precision of measurements at the parts-per-trillion concentration level with relative standard deviations varying from 4.1% (dibenzo[a,h]anthracene) to 13.4% (pyrene). The limits of detection were excellent as well and varied between 1.1 (anthracene) and 49.9 ng L⁻¹ (indeno[1,2,3-cd]pyrene). The recovery values of all the studied compounds meet the criterion for regulated polycyclic aromatic hydrocarbons, which mandates relative standard deviations equal or lower than 25%. The small volume of organic solvents (100 μL per sample) and amount of BEA (2 mg per sample) makes sample pre-concentration environmentally friendly and cost effective. The extraction procedure is well suited for numerous samples as the small working volume (1 mL) facilitates the implementation of simultaneous sample extraction. These are attractive features when routine monitoring of numerous samples is contemplated.     

Supercritical fluid extraction followed by supramolecular solvent microextraction as a fast and efficient preconcentration method for determination of polycyclic aromatic hydrocarbons in apple peels

In this work, reverse micelle‐based supramolecular solvent microextraction method coupled with supercritical fluid extraction and used for determining trace amounts of polycyclic aromatic hydrocarbons in apple peels. The extract was analyzed by high‐performance liquid chromatography equipped with a fluorescence detector. Coupling supramolecular solvent microextraction with supercritical fluid extraction method, resolve low preconcentration factor of supercritical fluid extraction method, improved limit of detection of polycyclic aromatic hydrocarbons and allow the use of supramolecular solvent microextraction in solid matrices. The effective parameters on the supramolecular solvent microextraction and supercritical fluid extraction efficiency were optimized using one variable at a time and face centered design methods, respectively. Under the optimum condition, the limits of detection and limits of quantifications were in the range of 0.34–1.27 and 1.03–3.82 µg/kg, respectively. Analysis of polycyclic aromatic hydrocarbons in apple peels showed that the supercritical fluid extraction/ supramolecular solvent microextraction method provide great potential for trace analysis of polycyclic aromatic hydrocarbons in fruit samples (RSDs < 7.7%).