Kinetic-spectrophotometric determination of trace amounts of As(III) based on its inhibitory effect on the redox reaction between bromate and hydrochloric acid

A simple, sensitive, rapid and reliable method has been developed for spectrophotometric determinations of As(III) in the presence of As(V) based on its inhibition effect on the redox reaction between bromate and hydrochloric acid. The decolorization of methyl orange by the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. The method allows the determination of arsenic in the range of 6-1000 mug l(-1). The relative standard deviation for 10 determinations of 40 mug l(-1) of As(III) was 1.43% and the limit of detection, corresponding to a signal to noise ratio of three, was 3.4 mug l(-1). The proposed method was applied to the determination of As(III) in water samples with satisfactory results.     

Promoting effect of iodide on the hexacyanomanganate(IV)-arsenic(III) redox reaction, for kinetic determination of iodide

The rate of the reaction between hexacyanomanganate(IV) and arsenic(III) in an acid medium is strongly accelerated by iodide. The reaction kinetics indicates that the iodide activity decreases throughout the reaction, probably because manganese(IV) oxidizes iodide to iodate (an inactive form). This behaviour is defined as promotion, rather than catalysis, and this rate-modifying effect has been used to determine iodide by a kinetic method. A linear calibration plot was obtained by a two-point fixed-time procedure. A detection limit of 0.2 ng/ml, a quantification limit of 0.6 ng/ml and relative standard deviations of 5.5 and 13% for the 6.7 and 0.6 ng/ml levels respectively have been found. Positive kinetic interferences from osmium(VIII) and iodate have been observed, and copper(II), silver(I) and mercury(II) inhibit the iodide activity by precipitaton. The method has been applied to determination of iodide in sodium arsenite (reagent grade) and table salt. The method has been validated by recovery experiments.     

Kinetic ultramicrodetermination of chromium(III) and osmium(VIII) based on their accelerating effect on the periodate-arsenite reaction

Summary A spectrophotometric kinetic method is described for the ultramicrodetermination of chromium (III) and osmium (VIII) based on their promoting and catalytic effect respectively on the periodate — arsenite reaction. For chromium(III) determination the decrease in absorbance within a fixed period of time is related directly to the chromium concentration. For osmium (VIII) determination the time required for the reaction to consume a fixed amount of periodate is measured automatically and related directly to the osmium concentration. Ultramicroamounts of chromium(III) in the 10^–6–10^–5 M level and of osmium(VIII) in the 10^–8–10^–7 M level were determined with a mean error of about 2%. The method has been applied to the determination of chromium in chrome ores.

---

Zusammenfassung Eine kinetische Methode zur Ultramikrobestimmung von Chrom(III) und Osmium(VIII) auf der Grundlage ihrer beschleunigenden bzw. katalytischen Wirkung auf die Perjodat-Arsenit-Reaktion wurde beschrieben. Für Chrom dient die Abnahme der Extinktion innerhalb einer bestimmten Zeitspanne als Maß der Konzentration. Bei der Bestimmung von Osmium(VIII) wird die Zeit für den Verbrauch einer bestimmten Menge Perjodat automatisch gemessen. Sie entspricht direkt der Osmiumkonzentration. Ultramikromengen Cr(III) in der Größenordnung 10^–6–10^–5 M und Os(VIII) in der Größenordnung 10^–8–10^–7 M sind mit einem Fehler von ungefähr 2% bestimmbar. Die Methode wurde zur Chrombestimmung in Erzen angewendet.

     

Kinetic determination of tellurium based on its inhibitory effect on the palladium(II)-catalysed reaction between pyronine G and hypophosphite ion

A kinetic method for the determination of Te based on its inhibitory effect on the PdII-catalysed reaction between pyronine G and H2PO2- is described. The influence of experimental variables on the rate of the process and the potential interfering effect of a large number of ions has been studied. Under the selected experimental conditions: 6 x 10(-5) M pyronine G; 0.6 M H2PO2-; pH 2.6, adjusted with Britton-Robinson buffer; 0.80 microgram ml-1 of PdII; and a temperature of 22 +/- 0.2 degrees C, Te was determined in the concentration range 0.08-0.85 microgram ml-1. The method was applied to the determination of Te in waters and lead concentrates.     

Indirect kinetic spectrophotometric determination of hydroxylamine based on its reaction with iodate.

A simple, precise and accurate method is proposed for rapid determination of trace amounts of hydroxylamine based on the reaction of hydroxylamine with iodate in acidic media. The reaction of neutral red by the produced nitrite ion was used to monitor the reaction spectrophotometrically at 525 nm by a fixed time method. Hydroxylamine in the range of 0.0400-1.200 microg mL(-1) could be determined. The relative standard deviation for 10 determinations of 0.500 microg mL(-1) hydroxylamine was 1.81% and the limit of detection was 0.010 microg mL(-1). The proposed method was applied to the determination of hydroxylamine in water samples with satisfactory results.     

Kinetic determination of Hg(II) based on its accelerating effect on the reaction between hexacyanoferrate(II) and 1,10-phenanthroline catalysed by micelles

A kinetic-photometric method for the determination of Hg(II) over the range 10-80 ng/ml is proposed. It is based on the accelerating effect of this ion on the reaction between hexacyanoferrate(II) and 1,10-phenanthroline which is monitored via the ferroin complex formed. Anionic sodium dodecyl sulphate (SDS) micelles, which catalyse the reaction, allow the ferroin complex to be formed under more acidic conditions. Combination of this pH shift and the development of the reaction in the vicinity of micelles results in improved selectivity in the determination of Hg(II) compared to the reaction occurring in an aqueous medium. Some observations on the effect of SDS on the reaction are reported.     

Ruthenium(III) catalysis in the reaction of hexacyanoferrate(III) and iodide ions in perchloric acid medium

RuCl₃ can further catalyze the reaction between hexacyanoferrate(III) and iodide ions, which is already catalyzed by the hydrogen ions obtained from perchloric acid. Rate, when the reaction is catalyzed only by the hydrogen ions, was separated graphically from the rate when ruthenium(III) and H⁺ ions both catalyze the reaction. Reactions studied separately in the presence as well as in the absence of RuCl₃ under similar conditions were found to follow second order kinetics w.r.t. [I⁻]. While the rate showed direct proportionality w.r.t. [Fe(CN)₆]³⁻ and [RuCl₃]. At low concentrations the reaction shows direct proportionality with respect to [H⁺] which tends to become proportional to the square of hydrogen ion concentrations. External addition of [Fe(CN)₆]⁴⁻ ions retards the reaction velocity while change in ionic strength of the medium has no effect on the rate. With the help of the intercept of the catalyst graph, extent of the reaction, which takes place without adding ruthenium(III) was calculated and it was in accordance with the values obtained from the separately studied reaction in which only H⁺ ions catalyze the reaction. It is proposed that ruthenium forms a complex, which slowly disproportionates into the rate-determining step. Arrhenius parameters at four different temperatures were also calculated.      

Kinetic-photometric determination of iodide based on its inhibitory effect on the bromate oxidation of Victoria Blue 4-R.

A new sensitive kinetic method has been developed for the determination of trace amounts of I- over the range of 50-300 ng cm(-3). The method was based on the inhibitory effect of iodide on the oxidation of Victoria Blue 4-R by KBrO3. The reaction is monitored spectrophotometrically at 596.3 nm. Method development includes optimization of reagent concentration and temperature. The kinetic parameters of the reaction were reported and a rate equation was suggested. The effects of certain foreign ions upon the reaction rate were determined for the assessment of the selectivity of the method. The proposed method was successfully applied to the determination of iodide in real samples. The new developed method was found to have fairly good selectivity, sensitivity, simplicity and rapidity.     

Kinetic-spectrophotometric determination of trace amounts of vanadium(V) based on its catalytic effect on the reaction of DBM-arsenazo and potassium bromate

A simple and sensitive kinetic-spectrophotometric method is developed for the determination of trace vanadium(V), based on the catalytic effect of vanadium(V) on the oxidation of DBM-arsenazo by potassium bromate in 0.0138 moll(-1) phosphoric acid medium and at 100 degrees C in the presence of citric acid as activator. The absorbance is measured at 528 nm with the fixed-time method. The optimization of the operating conditions regarding concentrations of the reagents, temperature and interferences are also investigated. The working curve is linear over the concentration range 0-20 ngml(-1) of vanadium(V) with good precision and accuracy and the detection limit was down to 3.44 ngl(-1). The relative standard deviation for a standard solution of 14 ngml(-1) is 0.28% (n=11). The apparent activity energies of the catalytic reaction and the non-catalytic reaction are 73.48, 113.5 kJ/mol, respectively. The proposed method proved highly sensitive, selective and relatively rapid for the assay of vanadium at low-level range of 0-20 ngml(-1) without any pre-concentration step. Thw method was applied to the determination of vanadium(V) in steels, rice, flour, cabbage, potato, fish, shrimp and tea samples with satisfactory results. The obtained results for the steel samples were excellent agreement with the standard reference values. The analytical results of the rice, flour, cabbage, potato, fish, shrimp and tea samples were excellent agreement with those of atomic absorption spectrometry. The recovery experiments have been made for the rice, flour, cabbage, potato, fish, shrimp and tea samples except the steels; excellent results were obtained. The relative standard deviations were over the range of 0.18-2.60% and the recoveries were over the range of 98.00-102.4%, respectively. The analytical results obtained were satisfactory.     

Spectrophotometric determination of periodate, iodate and bromate mixtures based on their reaction with iodide.

A rapid, simple, precise and accurate method is proposed for the determination of ternary mixtures of periodate-iodate-bromate based on their reaction with iodide ion at different pH values. The absorbance was measured at 352 nm. Three sets of reaction conditions were developed. In the first set of conditions, only periodate reacted with iodide, but in the second set the periodate and iodate reacted with iodide and in the third set the three ions reacted with iodide during the first 3 min after initiation of the reaction. The method could be used for individual determinations of periodate, iodate and bromate in the concentration range of 0.05-8.0 microg/ml, 0.05-5.0 microg/ml and 0.2-12 microg/ml, respectively. The data were evaluated by simultaneous equations.     

Sensitive kinetic-spectrophotometric determination of iodate in iodized table salt based on its accelerating effect on the reaction of bromate with chloride ion in the presence of hydrazine.

A simple, precise, sensitive and accurate method was developed for rapid determination of trace quantities of iodate. The method is based on the accelerating effect of iodate on the reaction of bromate and chloride acid in the presence of hydrazine in acidic media. The decolorization of Methyl Orange with the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. Iodate could be determined in the concentration ranges of 0.03 - 1.2 microg ml(-1). The relative standard deviation for ten replicate determinations of 0.3 microg ml(-1) of iodate was 1.65%. The proposed method was applied to the determination of iodate in table salts with satisfactory results.     

Voltammetric determination of As(III) in an aqueous zwitterionic complexing medium

Summary The polarographic behaviour and determination of As(III) in aqueous complexing electrolytes (bicine buffer solutions) ofpH values varying from 1.13–11.96 have been investigated at 25°C (direct current and differential pulse polarographic techniques). Using DC polarographic measurements, it was shown that reduction of As(III) takes place along one or three waves depending upon thepH value of the solution. Microcoulometric experiments have been performed at the limiting region of the different waves obtained at differentpH values. Cyclic voltammograms were recorded using a HDME to investigate the nature of reduction. Schemes for the mechanism of reduction occurring at the DME have been deduced. Kinetic parameters and wave characteristics for the reduction of As(III) have been calculated. A method for DPP determination of As(III) in bicine buffer solution ofpH 1.41 is reported. The detection limit of the method is 6.60×10^–8 M As(III).

---

Voltammetrische Bestimmung von As(III) in einem wäßrigen zwitterionischen komplexierenden Medium

Zusammenfassung Das polarographische Verhalten und die polarographische Bestimmung von As(III) in wäßrigen komplexierenden Elektrolyten (Bicin-Pufferlösungen) wurde beipH-Werten zwischen 1.13 und 11.96 und 25°C untersucht (Direktstrom- und Differentialpulstechniken). Mittels DC-Polarographie wurde gezeigt, daß die Reduktion von As(III) je nach dempH-Wert der Lösung in einer oder in drei Wellen erfolgt. In den Grenzbereichen der bei verschiedenenpH-Werten erhaltenen unterschiedlichen Wellen wurden microcoulometrische Experimente durchgeführt. Zur Untersuchung des Reduktionsvorgangs wurden cyclische Voltammogramme unter Verwendung einer HDME durchgeführt. Für den Mechanismus der an der Quecksilbertropfelektrode stattfindenden Reduktion wurden Reaktionsgleichungen ermittelt. Kinetische Parameter und Wellencharakteristika für die Reduktion von As(III) wurden berechnet. Eine Methode zur Bestimmung von As(III) mittels differentieller Pulspolarographie in Bicin-Pufferlòsung beipH 1.14 wird vorgestellt. Die Erfassungsgrenze der Methode liegt bei 6.60×10^–8 M As(III).

     

Kinetic determination of selenium, based on inhibition of the Pd(II)-catalysed reaction between pyronine G and hypophosphite

A new kinetic method for determination of selenium is based on its inhibitory effect on the Pd(II)-catalysed reaction between Pyronine G and hypophosphite. Under the optimum experimental conditions (6 x 10(-5)M Pyronine G, 0.4M hypophosphite, 0.4 mug/ml Pd(II), pH 2.8, temperature 22.0 +/- 0.2 degrees ), Se can be determined in the concentration range 0.033-0.50 mug/ml. The method suffers from numerous interferences and is thus limited in application. It has been applied to the determination of selenium in spring waters and pharmaceutical preparations.     

Spectrofluorimetric kinetic determination of selenium (IV) by flow injection analysis in cationic micellar medium

A sensitive catalytic kinetic spectrofluorimetric method for determining ng ml(-1) of selenium by flow injection analysis has been developed. The method, based on the catalytic effect of Se (IV) on the reduction of resorufin by sulphide, in the presence of cetylpyridinium chloride, is monitored spectrofluorimetrically (lambda(ex)=480 nm; lambda(em)=583 nm). The linearity range of the calibration graph is dependent on the concentration of sulphide. The variables affecting the rate of the reaction were investigated. The method is simple, rapid, precise, sensitive, and widely applicable. The limit of detection is 1 ng ml(-1) Se (IV), and the calibration range is 5-1000 ng ml(-1). Sampling rate is 60 samples h(-1), and the relative standard deviation of 12 determinations of 100 ng ml(-1) Se was 0.76%. The determination of Se (IV) in the presence of Se (VI) and total selenium is described. The method was applied to the determination of Se in selenium tablets, and several synthetic samples.     

Indirect spectrophotometric determination of traces of antimony(III) based on its oxidation by chromium(VI) and reaction of chromium(VI) with diphenylcarbazide

An indirect method for the determination of antimony(III) is described. Antimony(III) is oxidized to antimony(V) by chromium(VI) and the excess of chromium(VI) is then determined spectrophotometrically with diphenylcarbazide. Optimal conditions were established for both the determination of antimony(III) and the elimination or reduction of interferences. Antimony(III) can be determined quickly and easily in the range 0.05–5 mg l^?1; the relative standard deviation is 2% for 1.0 mg l^?1 antimony(III). The method is applicable to marine sediments and geothermal waters.     

Kinetic-spectrophotometric determination of Sb(V) based on its reaction with iodide in the presence of methylene blue

A rapid, simple, and sensitive kinetic method is developed for the determination of trace amounts of Sb(V). The method is based on the reaction of Sb(V) with iodide in acidic media in the presence of methylene blue. The reaction was monitored spectrophotometrically by measuring the decrease in the absorbance at 664 nm by a fixed-time technique of 60 s. The method allowed the determination of Sb(V) at concentrations between 0.01 and 2.2 μg/mL. The limit of detection was 0.006 μg/mL and the relative standard deviation for ten replicate measurements of 0.5 μg/mL Sb(V) was 1.2%. The method was applied to the determination of Sb(V) in tap water and spring water with satisfactory results. The text was submitted by the authors in English.