Inverted polymer solar cells with a solution-processed zinc oxide thin film as an electron collection layer

A solution-processed zinc oxide (ZnO) thin film as an electron collection layer for polymer solar cells (PSCs) with an inverted device structure was investigated. Power conversion efficiencies (PCEs) of PSCs made with a blend of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C61-butyric acid methyl ester (PCBM) are 3.50% and 1.21% for PSCs with and without the ZnO thin film, respectively. Light intensity dependence of the photocurrent and the capacitance-voltage measurement demonstrate that the increased PCEs are due to the restriction of the strong bimolecular recombination in the interface when a thin ZnO layer is inserted between the polymer active layer and the ITO electrode. These results demonstrate that the ZnO thin film plays an important role in the performance of PSCs with an inverted device structure.     

New alternating D–A1–D–A2 copolymer containing two electron‐deficient moieties based on benzothiadiazole and 9‐(2‐Octyldodecyl)‐8H‐pyrrolo[3,4‐b]bisthieno[2,3‐f:3',2'‐h]quinoxaline‐8,10(9H)‐dione for efficient polymer solar cells

A novel D–A₁–D–A₂ copolymer denoted as P1 containing two electron withdrawing units based on benzothiadiazole (BT) and 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3′,2′‐h]quinoxaline‐8,10(9H)–dione (PTQD) units was synthesized and characterized. The resulting copolymer exhibits a broad‐absorption spectrum, relatively deep lying HOMO energy level (?5.44 eV) and narrow optical bandgap (1.50 eV). Bulk heterojunction (BHJ) polymer solar cells (PSCs) based on P1 as donor and PC₇₁BM as acceptor with optimized donor to acceptor weight ratio of 1:2 and processed with DIO/CB solvent showed good photovoltaic performance with power conversion efficiency of 6.21% which is higher than that of the device processed without solvent additive (4.40%). The absorption and morphology investigations of the active layers indicated that structural and morphological changes were induced by the solvent additive. This higher power conversion efficiency could be mainly attributed to the absorption enhancement and improved charge transported in the active layer induced by the better nanoscale morphology of the active layer. This study demonstrated that a copolymer with two different acceptor moieties in the backbone may be promising candidate as donor copolymer for solution processed BHJ PSCs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 155–168     

High-efficiency quaternary polymer solar cells enabled with binary fullerene additives to reduce nonfullerene acceptor optical band gap and improve carriers transport

The polymer/small-molecule electron donor and nonfullerene organic electron acceptor are of structural similarity with both donor and acceptor molecules consisting of polycyclic fused-ring backbone and being decorated with alkyl-chains.In this study,we report that the introduction of binary fullerenes(C_(60)-/C_(70)-PCBM and C_(60)-/C_(70)-ICBA)into a nonfullerene binary system PBDB-T:ITIC reduces the polymer-nonfullerene acceptor intermixing,obtaining higher crystallinity with(100)crystal coherence length from 28 to 29–33 nm for the ITIC,and from 14 to 20–24 nm for the PBDB-T,and improved electron and hole mobilities both.Unprecedentedly,such a protocol reduces the ITIC optical band gap from 1.59 to 1.55 eV.As consequences,higher short-circuit current-density(17.8–18.4 vs.15.8 m A/cm~2),open-circuit voltage(0.92 vs.0.90 V)and fill-factor(0.72–0.73 vs.0.68)are simultaneously obtained,which ultimately afford higher efficient quaternary polymer solar cells with power conversion efficiencies(PCEs)up to 12.0%–12.8%comparing to the host binary device with 9.9%efficiency.For the polymer,ITIC,and ICBA/PCBM ternary blends,11%PCEs were recorded.The use of PCBM leads to larger red-shifting in thin film absorption and external quantum efficiency(EQE)response.Such effect is more pronounced when ICBA:PCBM mixture is used.These results indicate the size and shape of C_(60)and C_(70)as well as the substituent position of the second indene unit on C_(60)-/C_(70)-ICBA affect not only the blend morphology but also the electronic coupling in BHJ mixtures:the quaternary device performance increased in sequences of C_(70)-PCBM:C_(70)-ICBA→C_(70)-PCBM:C_(60)-ICBA→C_(60)-PCBM:C_(70)-ICBA→C_(60)-PCBM:C_(60)-ICBA.The resonant soft X-ray scattering(RSoXS)data indicated the most refined phase separation in the C_(60)-PCBM:C_(60)-ICBA based blend,corresponding to its best device function among the quaternary devices.These results indicate that the using of binary fullerenes as the acceptor additives allows for tuning nonfullerene blended film’s optical properties and filmmorphologies,shedding light on the designing high-performance multi-acceptor polymer solar cells.     

Inverted polymer solar cells with Zn2SnO4 nanoparticles as the electron extraction layer

In this study, we report narrow-size distribution Zn₂SnO₄ (ZSO) nanoparticles, which are produced by low-temperature solution-processed used as the electron extraction layer (EEL) in the inverted polymer solar cells (i-PSCs). Moreover, poly[(9,9-bis(3'-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) is used to modify the surface properties of ZSO thin film. By using the ZSO NPs/PFN as the EEL, the i-PSCs fabricated by poly[4,8-bis(2-ethylhexyloxyl)benzo[1,2-b:4,5-b'] dithio-phene-2,6-diyl-altethylhexyl-3-fluorothithieno [3,4-b]thiophene-2-carboxylate-4,6-diyl] (PTB7) blended with (6,6)-phenyl-C₇₁-butyric acid methylester (PC₇₁BM) bulk heterojunction (BHJ) composite, exhibits a power conversion efficiency (PCE) of 8.44%, which is nearly 10% enhancement as compared with that of 7.75% observed from the i-PSCs by PTB7:PC₇₁BM BHJ composite using the ZnO/PFN EEL. The enhanced PCE is originated from improved interfacial contact between the EEL with BHJ active layer and good energy level alignment between BHJ active layer and the EEL. Our results indicate that we provide a simple way to boost efficiency of i-PSCs.     

Synthesis and characterization of thieno[3,2‐b]thiophene‐isoindigo‐based copolymers as electron donor and hole transport materials for bulk‐heterojunction polymer solar cells

A novel class of thieno[3,2‐b]thiophene (TT) and isoindigo based copolymers were synthesized and evaluated as electron donor and hole transport materials in bulk‐heterojunction polymer solar cells (BHJ PSCs). These π‐conjugated donor‐acceptor polymers were derived from fused TT and isoindigo structures bridged by thiophene units. The band‐gaps and the highest occupied molecular orbital (HOMO) levels of the polymers were tuned using different conjugating lengths of thiophene units on the main chains, providing band‐gaps from 1.55 to 1.91 eV and HOMO levels from ?5.34 to ?5.71 eV, respectively. The corresponding lowest unoccupied molecular orbital (LUMO) levels were appropriately adjusted with the isoindigo units. Conventional BHJ PSCs (ITO/PEDOT:PSS/active layer/interlayer/Al) with an active layer composed of the polymer and PC₇₁BM were fabricated for evaluation. Power conversion efficiency from a low of 1.25% to a high of 4.69% were achieved with the best performing device provided by the D?π?A polymer with a relatively board absorption spectrum, high absorption coefficient, and more uniform blend morphology. These results demonstrate the potential of this class of thieno[3,2‐b]thiophene‐isoindigo‐based polymers as efficient electron donor and hole transport polymers for BHJ PSCs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of a Novel Low‐Bandgap Polymer Based on a Ladder‐Type Heptacyclic Arene Consisting of Outer Thieno[3,2‐b]thiophene Units for Efficient Photovoltaic Application

A novel conjugated polymer PIDTT‐quinoxaline (Qx) based on the coplanar thieno[3,2‐b]thiophene‐phenylene‐thieno[3,2‐b]thiophene structure is synthesized and evaluated as an electron‐donor material for bulk‐heterojunction polymer solar cells (BHJ PSCs). The absorption spectra, electrochemical, charge transport, and film morphology properties as well as theoretical modeling of PIDTT‐Qx are investigated to understand its intrinsic structure–property relationship. As expected, this polymer with an extended π‐conjugated backbone exhibits a narrow‐bandgap and board absorption spectrum for enhanced light harvesting. BHJ PSCs (ITO/PEDOT:PSS/polymer:PC₇₁BM/interlayer/Al) afford a maximum power conversion efficiency of 5.05% with an open‐circuit voltage of 0.84 V, a short‐circuit current density of 11.26 mA cm⁻², and a fill factor of 53.4%. These results demonstrate the potential of PIDTT‐Qx as an efficient electron‐donor material for BHJ PSCs.

     

Benzo[1,2-b:4,5-b′]dithiophene-based conjugated polyelectrolyte for the cathode modification of inverted polymer solar cells

A conjugated polyelectrolyte (CPE) named PBNBr, is prepared by post-quaternizing of poly{4,8-bis(octyloxy)benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl-alt-9,9-bis(3′-((N,N-dimethylamino)propyl)fluorene-2,7-diyl} (PBN) with bromoethane. The chemical strucutes, electrooptical properties of the PBNBr is fully characterized. As compared with the PBN, the PBNBr exhibit much better methanol solution processibility, and more effectively tuning ability for the work function (W_f) of ITO (W_F bare ITO, ?4.8 eV, W_F of ITO with PBN interlayer, ?4.1 eV, W_F of ITO with PBNBr interlayer ?3.9 eV). The open circuit voltages (V_OC) and power conversion efficiencies (PCEs) of polymer solar cells from the blend film of poly(3-hexylthiophene) (P3HT) and [6,6]-phenylC₆₁-butyric acid methyl ester (PC₆₁BM) with PBN and/or PBNBr modified ITO as cathode are respectively increased about 27% and 120% in contrast to those for the control devices with bare ITO as cathode. And PCEs of 4.21% and 4.53% are achieved in the PSCs with PBN and/or PBNBr modified ITO as cathode.     

Cove‐Edge Nanoribbon Materials for Efficient Inverted Halide Perovskite Solar Cells

Two cove‐edge graphene nanoribbons hPDI2‐Pyr‐hPDI2 ( 1 ) and hPDI3‐Pyr‐hPDI3 ( 2 ) are used as efficient electron‐transporting materials (ETMs) in inverted planar perovskite solar cells (PSCs). Devices based on the new graphene nanoribbons exhibit maximum power‐conversion efficiencies (PCEs) of 15.6 % and 16.5 % for 1 and 2 , respectively, while a maximum PCE of 14.9 % is achieved with devices based on [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM). The interfacial effects induced by these new materials are studied using photoluminescence (PL), and we find that 1 and 2 act as efficient electron‐extraction materials. Additionally, compared with PC₆₁BM, these new materials are more hydrophobic and have slightly higher LUMO energy levels, thus providing better device performance and higher device stability.     

Wide bandgap conjugated polymers based on bithiophene and benzotriazole for bulk heterojunction solar cells: Thiophene versus thieno[3,2-b]thiophene as π-conjugated spacers

Two wide bandgap (WBG) conjugated polymers, P2T-DTTTAZ and P2T-DTTAZ, with donor-π-acceptor (D-π-A) structures was designed and synthesized, utilizing thieno[3,2-b]thiophene (TT) and/or thiophene (T) units as π-bridge in conjugated polymer backbone. And, the wider optical band gap (E_g) of approximately 1.98 eV for P2T-DTTTAZ and 2.09 eV for P2T-DTTAZ were observed. Obviously, replacing T unit with larger conjugated plane TT unit as π-bridges, P2T-DTTTAZ resulted in the red shifted absorption and the reduced band gap, compared with these of P2T-DTTAZ. The polymer solar cells (PSCs) with an inverted device structure based on P2T-DTTTAZ or P2T-DTTAZ as donor and [6,6] phenyl-C₆₁ butyric acid methyl ester (PC₆₁BM) as acceptor were assembled and the photovoltaic properties were also investigated. The power conversion efficiencies (PCEs) of 1.57% for P2T-DTTTAZ and 1.25% for P2T-DTTAZ were obtained.     

Polymers for application in organic solar cells: Bithiophene can work better than thienothiophene when coupled to benzodithiophene

The synthesis and characterization of two low band gap copolymers ( P1 and P2 ) incorporating benzo[1,2‐b:4,5‐b']dithiophene unit substituted with octylsulfanylthienyl groups (OSBT) are here reported. These materials, designed to be employed in polymer solar cells (PSCs), were obtained from alternating OSBT and bithiophene ( P1 ) or thienothiophene ( P2 ) units. Their structural electrochemical and photophysical properties were investigated. They are thermally stable and soluble in organic solvents from which they easily form films. They also form π‐stacks in solution, in film and display a moderate solvatochromism. These polymers were tested with [70]PCBM in bulk‐heterojunction (BHJ) PSCs where they act as donor materials and [70]PCBM is the electron acceptor. The best device, obtained using a 1:3 weight ratio for the P1 :[70]PCBM blend, shows a PCE around 1.5%. A broad response from 350 to 700 nm is also observed in the external quantum efficiency (EQE) curves, wider for P1 with respect to P2 . © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1603–1614     

Thiadiazoloquinoxaline and benzodithiophene bearing polymers for electrochromic and organic photovoltaic applications

Abstract

Two novel thiadiazoloquinoxaline and benzodithiophene (BDT) bearing copolymers were designed and synthesized. Different BDT units (alkoxy and thiophene substituted) were used as donor materials and the effect of alkoxy and thiophene substitution on the electrochemical, spectroelectrochemical and photovoltaic properties were investigated. Both polymers exhibited low oxidation potentials at around 0.90 V and low optical band gaps at around 1.00?eV due to the insertion of electron poor thiadiazoloquinoxaline unit into the polymer backbone. Both P1 (poly-6,7-bis(3,4-bis(decyloxy)phenyl)-4-(4,8-bis(nonan-3-yloxy)benzo[1,2-b:4,5-b']dithiophen-2-yl)-[1, 2, 5]thiadiazolo[3,4-g]quinoxaline) and P2 (poly- 4-(4,8-bis(5-(nonan-3-yl)thiophen-2-yl)benzo[1,2-b:4,5-b']dithiophen-2-yl)-6,7-bis(3,4-bis(decyloxy)phenyl)-[1, 2, 5]thiadiazolo[3,4-g]quinoxaline) exhibited multichromic behavior with different tones of greenish yellow and gray in the neutral and fully oxidized states, respectively. In addition, both polymers revealed very high optical contrasts (～87%) in the NIR region which make these promising polymers good candidates for NIR applications. Finally, in order to explore the organic photovoltaic performances, P1 and P2 were mixed with PC₇₁BM in the active layer of organic solar cells (OSCs) by conventional device structure. As a result P1 and P2 based devices revealed power conversion efficiencies (PCEs) of 0.33% and 0.60% respectively. However, the additive treatment enhanced PCE from 0.49 to 0.73% for P2 based devices.     

Donor-acceptor (D-A) terpolymers based on alkyl-DPP and t-BocDPP moieties for polymer solar cells

A series of low band gap terpolymers based on 4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b¢] dithiophene (BDTT) and diketopyrrolopyrrole (DPP) with varied solubilizing groups (i.e., tert-butoxycarbonyl, t-Boc and 2-octyldodecyl) are developed as electron donors for bulk heterojunction (BHJ) polymer solar cells (PSCs). The results reveal that the one with 50% t-Boc concentration (P3) performs better than the other terpolymers used in this study in conventional PSC devices with a power conversion efficiency of 2.92%.     

聚(3-己基噻吩)作为光谱增感层在有机太阳电池光谱响应增强中的应用

报道了利用聚(3-己基噻吩)(P3HT)作为前置缓冲层来弥补(4,8-双-(2-乙基己氧基)-苯并[1,2-b:4,5-b']二噻吩)-(4-氟代噻并[3,4-b]噻吩(PBDT-TT-F):[6,6]-苯基-C₆₁-丁酸甲酯(PC₆₁BM)共混体相异质结(BHJ)电池对450-600 nm处光谱响应不足的新的器件结构设计思路. 光谱带隙为1.8 eV的PBDT-TT-F 在550-700 nm处有很强的光谱吸收, 在有机太阳电池器件上有很好的应用潜能. 但其在350-550 nm处的吸收不强, 影响了器件对太阳光谱的利用效率. 与此相比, P3HT薄膜的光谱吸收主要在450-600 nm范围内, 同PBDT-TT-F 形成良好的互补关系. 新设计的器件外量子效率(EQE)研究结果表明, 利用P3HT 作为前置缓冲层可以与PBDT-TT-F:PC₆₁BM薄膜中的PC₆₁BM形成平面异质结, 从而拓展了器件在450-600 nm处的光谱响应范围,实现光谱增感作用. 优化P3HT的厚度为20 nm左右, 器件对外输出的短路光电流密度从11.42 mA·cm^-2提高到12.15 mA·cm^-2, 达到了6.3%的提升.     

All‐Polymer Solar Cells: Recent Progress,Challenges, and Prospects

For over two decades bulk‐heterojunction polymer solar cell (BHJ‐PSC) research was dominated by donor:acceptor BHJ blends based on polymer donors and fullerene molecular acceptors. This situation has changed recently, with non‐fullerene PSCs developing very rapidly. The power conversion efficiencies of non‐fullerene PSCs have now reached over 15 %, which is far above the most efficient fullerene‐based PSCs. Among the various non‐fullerene PSCs, all‐polymer solar cells (APSCs) based on polymer donor‐polymer acceptor BHJs have attracted growing attention, due to the following attractions: 1) large and tunable light absorption of the polymer donor/polymer acceptor pair; 2) robustness of the BHJ film morphology; 3) compatibility with large scale/large area manufacturing; 4) long‐term stability of the cell to external environmental and mechanical stresses. This Minireview highlights the opportunities offered by APSCs, selected polymer families suitable for these devices with optimization to enhance the performance further, and discusses the challenges facing APSC development for commercial applications.     

Bowl-Assisted Ball Assembly for Solvent-Processing the C60 Electron Transport Layer of High-Performance Inverted Perovskite Solar Cell

Pristine fullerene C₆₀ is an excellent electron transport material for state-of-the-art inverted structure perovskite solar cells (PSCs), but its low solubility leaves thermal evaporation as the only method for depositing it into a high-quality electron transport layer (ETL). To address this problem, we herein introduce a highly soluble bowl-shaped additive, corannulene, to assist in C₆₀-assembly into a smooth and compact film through the favorable bowl-ball interaction. Our results show that not only corannulene can dramatically enhance the film formability of C₆₀, it also plays a critical role in forming C₆₀-corannulene (CC) supramolecular species and in boosting intermolecular electron transport dynamics in the ETL. This strategy has allowed CC devices to deliver high power conversion efficiencies up to 21.69 %, which is the highest value among the PSCs based on the solution-processed-C₆₀ (SP-C₆₀) ETL. Moreover, the stability of the CC device is far superior to that of the C₆₀-only device because corannulene can retard and curb the spontaneous aggregation of C₆₀. This work establishes the bowl-assisted ball assembly strategy for developing low-cost and efficient SP-C₆₀ ETLs with high promise for fully-SP PSCs.     

Platinum(II)-bis(aryleneethynylene) complexes for solution-processible molecular bulk heterojunction solar cells

Four new solution-processible small-molecular platinum(II)-bis(aryleneethynylene) complexes consisting of benzothiadiazole as the electron acceptor and triphenylamine and/or thiophene as the electron donor were conveniently synthesized and characterized by physicochemical and computational methods, and utilized as the electron-donor materials in the fabrication of solution-processed bulk heterojunction (BHJ) solar cells. The effect of different electron-donor groups in these small molecules on the optoelectronic and photovoltaic properties was also examined. The optical and time-dependent density functional theory studies showed that the incorporation of stronger electron-donor groups significantly enhanced the solar-absorption abilities of the complexes. These molecular complexes can serve as good electron donors for fabricating BHJ devices by blending them with the [6,6]-phenyl-C(71)-butyric acid methyl ester (PC(70)BM) as the electron acceptor. The best power conversion efficiency of 2.37% was achieved with the open-circuit voltage of 0.83 V, short-circuit current density of 7.10 mA cm(-2) and fill factor of 0.40 under illumination of an AM 1.5 solar-cell simulator. The spin-coated thin films showed p-channel field-effect charge transport with hole mobilities of up to 2.4×10(-4) cm(2) V(-1) s(-1) for these molecules. The present work illuminates the potential of well-defined organometallic complexes in developing light-harvesting small molecules for efficient power generation in organic photovoltaics implementation.     

Synthesis of three new 1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl) pyrrole‐based donor polymers and their bulk heterojunction solar cell applications

A series of three new 1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole‐based polymers such as poly[1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole] ( PTPT ), poly[1,4‐(2,5‐bis(octyloxy)phenylene)‐alt‐5,5'‐(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole)] ( PPTPT ), and poly[2,5‐(3‐octylthiophene)‐alt‐5,5'‐(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole)] ( PTTPT ) were synthesized and characterized. The new polymers were readily soluble in common organic solvents and the thermogravimetric analysis showed that the three polymers are thermally stable with the 5% degradation temperature >379 °C. The absorption maxima of the polymers were 478, 483, and 485 nm in thin film and the optical band gaps calculated from the onset wavelength of the optical absorption were 2.15, 2.20, and 2.13 eV, respectively. Each of the polymers was investigated as an electron donor blending with PC₇₀BM as an electron acceptor in bulk heterojunction (BHJ) solar cells. BHJ solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM/TiO_x/Al configurations. The BHJ solar cell with PPTPT :PC₇₀BM (1:5 wt %) showed the power conversion efficiency (PCE) of 1.35% (J_sc = 7.41 mA/cm², V_oc = 0.56 V, FF = 33%), measured using AM 1.5G solar simulator at 100 mW/cm² light illumination. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Incorporation of Hexa‐peri‐hexabenzocoronene (HBC) into Carbazole–Benzo‐2,1,3‐thiadiazole Copolymers to Improve Hole Mobility and Photovoltaic Performance

Hexa‐peri‐hexabenzocoronene (HBC) is a discotic‐shaped conjugated molecule with strong π–π stacking property, high intrinsic charge mobility, and good self‐assembly properties. For a long time, however, organic photovoltaic (OPV) solar cells based on HBC demonstrated low power conversion efficiencies (PCEs). In this study, two conjugated terpolymers, poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5′‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT)‐ 5 HBC and PCDTBT‐ 10 HBC, were synthesized by incorporating different amounts of HBC as the third component into poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5′‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT) through Suzuki coupling polymerization. For comparison, the donor–acceptor (D –A) conjugated dipolymer PCDTBT was also synthesized to investigate the effect of HBC units on conjugated polymers. The HBC‐containing polymers exhibited higher thermal stabilities, broader absorption spectra, and lower highest‐occupied molecular orbital (HOMO) energy levels. In particular, the field‐effect mobilities were enhanced by more than one order of magnitude after the incorporation of HBC into the conjugated polymer backbone on account of increased interchain π–π stacking interactions. The bulk heterojunction (BHJ) polymer solar cells (PSCs) fabricated with the polymers as donor and PC₇₁BM as acceptor demonstrated gradual improvement of open‐circuit voltage (V_OC) and short‐circuit current (J_SC) with the increase in HBC content. As a result, the PCEs were improved from 3.21 % for PCDTBT to 3.78 % for PCDTBT‐ 5 HBC and then to 4.20 % for PCDTBT‐ 10 HBC.     

A two-dimension medium band gap conjugated polymer based on 5,10-bis(alkylthien-2-yl)dithieno[3,2-d:3′,2′-d′]benzo[1,2-b:4,5-b′]dithiophene: Synthesis and photovoltaic application

A two-dimension medium band gap copolymer poly{5,10-bis(4,5-didecylthien-2-yl)dithieno[2,3-d:2′,3′-d′]benzo[1,2-b:4,5-b′]dithiophene-2,7-diyl-alt-2,5-di(3-octylthien-2-yl) thiophen-5,5′-diyl}, named as PDTBDT-T-3T, was prepared by the palladium-catalyzed Stille cross coupling reaction and characterized. The resulting polymer exhibits good solubility in common organic solvents, excellent thermal stability, and extensive light absorption from 300 nm to 650 nm with an optical band gap of 1.92 eV, the highest occupied molecular orbital (HOMO) level of ?5.03 eV and the hole mobility up to 1.92 × 10^?4 cm²·V^?1·s^?1. The power conversion efficiencies (PCEs) of 2.02%–3.19% have been achieved in the traditional PVCs for the copolymer. It should be noted that the PCEs of 4.2% for the inverted PVCs from the copolymer with PFN (poly[(9,9-bis(3′-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl- fluorene)]) as cathode modifying interlayer, were similar with the PCEs of 4.39% for the inverted PVCs from P3HT:PC₇₁BM at the same condition. These results indicated that the copolymer could be used as potential candidate for P3HT.     

A benzo[ghi]-perylene triimide based double-cable conjugated polymer for single-component organic solar cells

Single-component organic solar cells (SCOSCs) with high stability and simplified fabrication process are supposed to accelerate the commercialization of organic photovoltaics. However, the types of photo-active materials and photovoltaic performance of SCOSCs are still far lagging behind the bulk-heterojunction type organic solar cells (BHJ OSCs). It is still an arduous task to introduce new photo-active materials into SCOSCs, aiming to improve the efficiencies of SCOSCs. One feasible way is to construct double-cable polymers with new structures and tune conformation, morphology and mobility for the improvement in power conversion efficiencies (PCEs). Hence, in this work, we constructed a new double-cable polymer PBTT-BPTI by introducing fused core 5,7-dibromo-2,3-bis(2-ethylhexyl)benzo[1,2-b:4,5-c’]dithiophene-4,8-dione (TTDO) into the main backbone and benzo[ghi]-perylene triimide (BPTI) unit into the side chain. Both of the two units show strong electron-withdrawing property, which are expected to broaden absorption spectra and enhance intermolecular interaction. The double-cable polymer exhibited a broad absorption in the range of 300-700 nm with an optical band gap (E_g) of 1.79 eV. The PCE of PBTT-BPTI-based SCOSCs was 2.15%, which may be limited by the unconstructed efficient electron transporting channels.