Bi4Ti3O12 Thin Films from Mixed Bismuth-Titanium Alkoxides

Bi₄Ti₃O₁₂ thin films were obtained by the sol-gel method. The precursor solution was prepared by allowing the two metallic alkoxides, Bi(OC₂H₄OCH₃)₃ and Ti(OC₂H₄OCH₃)₄, to react in 2-methoxy-ethanol to form the mixed alkoxide. This stable sol was deposited by spin-coating onto platinized silicon substrates. X-Ray diffraction patterns indicate that the perovskite initial crystallization temperature is 460°C for powder samples and it ranges between 400 and 500°C, for thin films, as a function of the number of coating layers. Dense, smooth and crack free thin films with grain sizes ranging from 20 nm to 500 nm are obtained, depending on the number of coating layers and on the post-deposition temperature annealing.     

Influence of Preparation Conditions on Crystallization Behavior of the Complex Alkoxide Derived PbTiO3 Powder

PbTiO₃ powders were prepared by hydrolysis of the complex alkoxide derived from Pb(OCOCH₃)₂ and Ti(OCH₂CH₃)₄, and their crystallization behaviors were investigated by DTA. Influence of conditions of synthesis and hydrolysis of the Pb-Ti complex alkoxide and heating atmosphere on crystallization behavior of powder was examined.Powders consisting of spherical particles with submicron diameter could be obtained by using the reaction time over 16 hr for synthesis, and the use of acetone-ethanol solvent with ammonia catalyst for the hydrolysis of the complex alkoxide. The resultant powders crystallized to tetragonal PbTiO₃ perovskite above 250°C under O₂ flow, and then transformed to cubic perovskite at 490°C. The powder heated at 250°C for 1 hr in O₂ consisted of well-crystallized tetragonal perovskite crystals of cubic shape of 0.2 to 1 µm in size.     

X-ray and Raman study of spray pyrolysed vanadium oxide thin films

Vanadium oxide thin films were prepared by spray pyrolysis using solutions of vanadium chloride (VCl₃) with different concentrations on glass substrates heated at 200 and 250 °C. The influence of substrate temperature (T_s) and solution concentration (molarity) on structural and vibrational properties is discussed by using X-ray diffraction and Raman spectroscopy. The results revealed that at 0.05 M and T_s = 200 °C, V₄O₉ thin films are obtained. At 250 °C, V₂O₅ phases with preferential orientation are observed and the films become polycrystalline when the molarity increases.     

Preparation of nitrogen doped zinc oxide nanoparticles and thin films by colloidal route and low temperature nitridation process

Nitrogen doped zinc oxide (ZnO) nanoparticles have been synthesized using a colloidal route and low temperature nitridation process. Based on these results, 200 nm thick transparent ZnO thin films have been prepared by dip-coating on SiO₂ substrate from a ZnO colloidal solution. Zinc peroxide (ZnO₂) thin film was then obtained after the chemical conversion of a ZnO colloidal thin film by H₂O₂ solution. Finally, a nitrogen doped ZnO nanocrystalline thin film (ZnO:N) was obtained by ammonolysis at 250 °C. All the films have been characterized by scanning electron microscopy, X-ray diffraction, X-Ray photoelectron spectroscopy and UV–Visible transmittance spectroscopy.     

Fabrication of copper–zinc oxide composite thin films from single source precursor by aerosol assisted chemical vapour deposition

A new heterobimetallic complex, Zn₂(OAc)₆(μ-O)₂Cu₄(bdmap)₂Cl₂ (1) where bdmap = 1,3-bis(dimethylamino)-2-propanolato and OAc = acetato, was synthesized by direct interaction of a 2:1.5 mixture of Cu(OCH₃)Cl/Zn(OAc)₂ · 2H₂O with bdmapH in toluene at room temperature and characterized by melting point, elemental analysis, FT-IR spectroscopy, mass spectrometry, thermogravimetric analysis (TGA) and single crystal X-ray diffraction. The aerosol assisted chemical vapour deposition (AACVD) from complex (1) showed that it is a promising precursor to deposit thin films of crystalline Cu–ZnO (2:1) composite. The chemical composition and surface morphology of the deposited thin films were analysed by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM) and energy dispersive analytical X-ray (EDAX), which suggest that the films were thin, crystalline, uniform, smooth and tightly adherent to the substrates with particle size ranging from 0.2–0.5 μm at 250 °C to 0.4–0.9 μm at 475 °C. It was also shown that size of the crystallite can be controlled by controlling deposition temperature of the films. The thickness and voltage–current characteristics of thin films were measured with profilometer and voltmeter by using the four-probe method.     

The effect of different substrate temperatures on the structure and luminescence properties of Y2O3:Bi3+ thin films

Y₂O₃:Bi³⁺ phosphor thin films were prepared by pulsed laser deposition in the presence of oxygen (O₂) gas. The microstructure and photoluminescence (PL) of these films were found to be highly dependent on the substrate temperature. X-ray diffraction analysis showed that the Y₂O₃:Bi³⁺ films transformed from amorphous to cubic and monoclinic phases when the substrate temperature was increased up to 600 °C. At the higher substrate temperature of 600 °C, the cubic phase became dominant. The crystallinity of the thin films, therefore, increased with increasing substrate temperatures. Surface morphology results obtained by atomic force microscopy showed a decrease in the surface roughness with an increase in substrate temperature. The increase in the PL intensities was attributed to the crystallinity improvement and surface roughness decrease. The main PL emission peak position of the thin films prepared at substrate temperatures of 450 °C and 600 °C showed a shift to shorter wavelengths of 460 and 480 nm respectively, if compared to the main PL peak position of the powder at 495 nm. The shift was attributed to a different Bi³⁺ ion environment in the monoclinic and cubic phases.     

Photoelectrochemical Properties of Sol-Gel Processed Ag-TiO2 Nanocomposite Thin Films

Ag-TiO₂ thin films were prepared with a sol-gel route, using titanium isopropoxide and silver nitrate as precursors, at 0, 0.03 and 0.06 Ag/Ti nominal atomic ratios. After drying at 80°C, the films were fired at 300°C, 500°C, and 600°C for 30 min and 5 h. Glancing angle X-ray diffraction (XRD) analysis and X-ray photoelectron spectroscopy (XPS), with depth profiling of the concentration, were used to study the films. XPS analysis showed the presence of C and N as impurities in the nanocomposite films. Their concentration decreased with increasing the firing temperature. Chemical state analysis showed that Ag was present in metallic state, except for the outer layer where it was present as Ag⁺. For the films prepared with a Agt/Ti concentration of 0.06, depth profiling measurements of the film fired at 300°C showed a strong Ag enrichment at the outer surface, while composition remained almost constant within the rest of the film, at Ag/Ti atomic ratio of 0.02. Two layers were found for the films heated to 500°C, where the Ag/Ti ratios were 0.015 near the surface and 0.03 near the substrate. The photoelectrochemical properties of Ag-TiO₂ were studied for thin films deposited on ITO substrates. Photocurrents of Ag-TiO₂ nanocomposite electrodes fired at 300°C were observed even at visible light, for wavelengths longer than 400 nm.     

Hydrothermal synthesis of 2D ordered macroporous ZnO films

The ZnO films with two-dimensional ordered macroporous structure were successfully fabricated through hydrothermal crystal growth of ZnO on the ZnO substrate covered with a monolayer of polystyrene (PS) spheres as template. The precursor solution of hydrothermal crystal growth of ZnO were prepared by equimolar solution of Zn(NO₃)₂·6H₂O and hexamethylenetramine (HMT). The confinement effect of the PS spheres template on the growth of ZnO nanorods and the influence of sodium citrate on the crystal growth of ZnO had been studied. The film surface morphology and the preferential growth of ZnO crystal were investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. Also, the photoluminescence spectrum of ZnO films had been measured, and the corresponding mechanism was discussed. __________ Translated from Chemistry, 2007, 70 (8): 587–592 [译自: 化学通报]     

Synthesis and characterization of ZnO nanowires by thermal oxidation of Zn thin films at various temperatures

In this research high-quality zinc oxide (ZnO) nanowires have been synthesized by thermal oxidation of metallic Zn thin films. Metallic Zn films with thicknesses of 250 nm have been deposited on a glass substrate by the PVD technique. The deposited zinc thin films were oxidized in air at various temperatures ranging between 450 °C to 650 °C. Surface morphology, structural and optical properties of the ZnO nanowires were examined by scanning electron microscope (SEM), X-ray diffraction (XRD), energy dispersive X-ray (EDX) and photoluminescence (PL) measurements. XRD analysis demonstrated that the ZnO nanowires has a wurtzite structure with orientation of (002), and the nanowires prepared at 600 °C has a better crystalline quality than samples prepared at other temperatures. SEM results indicate that by increasing the oxidation temperature, the dimensions of the ZnO nanowires increase. The optimum temperature for synthesizing high density, ZnO nanowires was determined to be 600 °C. EDX results revealed that only Zn and O are present in the samples, indicating a pure ZnO composition. The PL spectra of as-synthesized nanowires exhibited a strong UV emission and a relatively weak green emission.     

ZnO thin films electrodeposited in propylene carbonate under a magnetic field

Electrochemical processing of ZnO films on fluorine-doped indium tin oxide (FTO/ITO) substrate was investigated in organic propylene carbonate electrolyte solutions containing Zn(NO₃)₂·6H₂O. Much finer and more uniform morphologies of the ZnO films were obtained in comparison with those in aqueous electrolyte solutions. The effects of superimposing a magnetic field to the ZnO films were further examined. Superimposing a magnetic field considerably influenced the transient current density in the initial stage, especially in the mass transfer controlled region at −1.5 V vs Zn wire reference electrode. It also introduced substantially no drastic influence on the microstructure in spite of the appearance of considerably significant morphological variations. Contribution to special issue on Magnetic field effects in Electrochemistry.     

A low-temperature synthesis of ultraviolet-light-emitting ZnO nanotubes and tubular whiskers

We have successfully synthesized single-crystal ZnO nanotubes and tubular whiskers by employing Zn(NO₃)₂·6H₂O, NH₃·H₂O as the starting materials in the presence of polyethylene glycol (PEG, M_w=2000) at ambient pressure and low temperature (70 °C). Characterizations are carried out by X-ray powder diffraction (XRD), X-ray energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), transmission electron microscopy (TEM, HRTEM) and photoluminescence (PL) measurement. The results show that the as-prepared ZnO are tubular textures, which have average cross-sectional dimensions of 200-300 nm, lengths of 2-3.5 μm, and wall thickness of 80 nm. These tubular products demonstrate a sharp ultraviolet excitonic emission peak centered at 385 nm at room temperature. A possible growth mechanism and the influence of the reaction temperature on the formation of crystalline ZnO are presented.     

Sol-Gel Preparation and Characterization of Ag-TiO2 Nanocomposite Thin Films

Ag-TiO₂ thin films were prepared with a sol-gel route, using titanium isopropoxide and silver nitrate as precursors, at 0.03 and 0.06 Ag/Ti nominal atomic ratios. After drying at 80°C, the films were fired at 300°C and 500°C for 30 min. The films were analysed by X-ray diffraction (XRD) with glancing angle, and X-ray photoelectron spectroscopy (XPS), with depth profiling of the concentration. XPS analysis showed the presence of C and N as impurities in the nanocomposite films. Their concentration decreased with increasing the firing temperature. Chemical state analysis showed that Ag was present in metallic state, except for the very outer layer where it was present as Ag⁺. For the films prepared with a Ag/Ti concentration of 0.06, depth profiling measurements of the film fired at 300°C showed a strong Ag enrichment at the outer surface, while composition remained almost constant within the rest of the film, at 0.019. For the films heated to 500°C, two layers were found, where the Ag/Ti ratios were 0.015 near the surface and 0.026 near the substrate.     

Preparation and Characterization of Molybdenum Oxide Thin Films by Sol-Gel Process

This paper presents a new sol-gel process to prepare molybdenum oxide thin films. A molybdenum acetylacetonate sol was prepared by employing the system CH₃COCH₂COCH₃/MoO₃/C₆H₅CH₃/HOCH₂CH₂OCH₃. A molybdenum acetylacetonate gel was prepared by addition of aqueous NH₃. Thermal gravimetry (TG) and differential thermal analyses (DTA) of the gel suggested that crystallization of MoO₃ occurs in a 140 K temperature range around 508°C. MoO₃ films were prepared on fused silica, Si (111) and Al₂O₃ (012) substrates by annealing spin coating films of the sol in oxygen environment at 508°C. X-ray diffraction (XRD) showed that all films crystallize in -MoO₃ structure, and crystallites on fused silica substrate are arbitrarily oriented while those on Si (111) and Al₂O₃(012) substrates oriented in the (010) direction. SEM investigations showed that MoO₃ grains of all films are randomly distributed, with a longitudinal dimension of about 1–5 m and the film thickness is about 1 m.     

Effect of α-Hydroxyketones as Chelate Ligands on Dip-Coating of Zirconia Thin Films

The stabilization effects of -hydroxyketones such as acetoin, acetol, and their imine derivatives of monoethanolamine (MEA) on the 2-propanol solution of metal alkoxides (Al, Ti, Zr, Nb and Ta) were investigated. The hydroxyketones, especially acetoin which has a moderate boiling point around 150°C, were found to have a stabilization effect on the alkoxides of Ti^IV, Nb^V and Ta^V already in their molar ratios of 2, while the Zr^IV alkoxide was stabilized at the molar ratio of 4. By sol-gel processing using this acetoin-stabilized solution, crystallized ZrO₂ thin films could be prepared at temperatures as low as 400°C, which was lower than that from a diethanolamine (DEA)-stabilized precursor (450°C). The films prepared in this study showed a high transparency (more than 90%, UV-VIS spectroscopy), suggesting that the use of chelate ligands with low boiling points is a good way to lower the crystallization temperature of sol-gel-derived ZrO₂ thin films. The Zr complexes of the imines made by the reaction between the hydroxyketones and MEA were stable and photosensitive (<500 nm), making it possible to pattern ZrO₂ films by photo-irradiation of their gel films.     

Controlled-synthesis of ZnO nanorings

ZnO nanorings were synthesized on a large scale by an easy solution-based method at 70°C for 5 h using hexamethylenetramine (C₆H₁₂N₄, HMT) and Zn (NO₃)₂·2H₂O as raw materials in the presence of surfactant poly(acrylamide-co-diallyldimethylammonium chloride) (PAM-CTAC). The structure and morphology of the products were characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). The influence of experimental conditions such as concentration of surfactant and reactants, reaction temperature on the structure and morphology of the products were investigated. A probable formation mechanism of ZnO nanorings in the presence of surfactant PAM-CTAC was discussed. The results show that the products are wurtzite hexagonal ZnO nanorings with an inner diameter of 220 nm and a wall thickness of 70 nm. Reaction temperature and concentration of reactants influence the shape and size of ZnO nanorings but PAM-CTAC plays the key role in the formation of ZnO nanorings. Through adjusting the concentration of PAM-CTAC, controlled-synthesis of ZnO nanorings can be realized. A room temperature photoluminescence (PL) spectrum of ZnO obtained shows that the full width at half maximum (FWHM) of the UV emission (∼7 nm) is much narrower than that of commercial ZnO bulk crystals (∼18 nm). The narrow FWHM confirms the uniformity and narrow size distribution of the synthesized ZnO crystals. __________ Translated from Chemical Journal of Chinese Universities, 2008, 29(1): 28–32     

ZnO thin films prepared on titanium substrate by PLD technique at different substrate temperatures

ZnO thin films were grown by pulsed laser deposition on titanium substrates at different substrate temperatures ranging from 300 to 700 °C. X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS),photoluminescence, and Raman spectroscopy are employed to investigate the change of properties. XRD, XPS, and Raman data showed that the films consisted of TiO₂ at high substrate temperature, which will deteriorate the crystallization quality of ZnO films. The optimum temperature for the growth of ZnO films on the Ti substrate is about 500 °C in this paper. The ZnO films grown on titanium substrate can be used in direct current, microwave, and medical applications. Copyright © 2014 John Wiley & Sons, Ltd.     

Aqueous pathways for formation of zinc oxide particles in the presence of carboxymethyl inulin

In this study, zinc oxide (ZnO) crystals were obtained by a simple wet chemical method using zinc nitrate hexahydrate (Zn(NO₃)₂·6H₂O) and hexamethylenetetramine as the starting materials in the presence of the water-soluble biopolymer carboxymethyl inulin (CMI). We investigated the effect of reaction temperature and CMI concentration on the morphology, surface area, particle size, and size distribution of zinc oxide. X-ray diffraction analysis showed the XRD patterns for all the samples were similar to that of ZnO with the wurtzite structure, irrespective of the geometric shape of the particle. The ZnO rod grows preferentially along the [001] direction in the absence of the CMI. The biopolymer affects the ZnO crystals in a concentration-dependent manner by altering the growth rate of the particles along the c-axis and a-axis. The vast majority of the crystals have a central grain boundary in the presence of CMI. The precipitate consisted of micrometer-sized hexagonally shaped bipyramidal ZnO crystals and nanocrystals.     

Study on the Synthesis of ZnO Nanoparticles Using Azadirachta indica Extracts for the Fabrication of a Gas Sensor

This paper compared the effects of A. indica plant proteins over chemical methods in the morphology of zinc oxide nanoparticles (ZnO NPs) prepared by a co-precipitation method, and ethanol sensing performance of prepared thin films deposited over a fluorene-doped tin oxide (FTO) bind glass substrate using spray pyrolysis technique. The average crystallite sizes and diameters of the grain-sized cluster ZnO NPs were 25 and (701.79 ± 176.21) nm for an undoped sample and 20 and (489.99 ± 112.96) nm for A. india dye-doped sample. The fourier transform infrared spectroscopy (FTIR) analysis confirmed the formation of the Zn–O bond at 450 cm⁻¹, and also showed the presence of plant proteins due to A. indica dye extracts. ZnO NPs films exhibited good response (up to 51 and 72% for without and with A. indica dye-doped extracts, respectively) toward ethanol vapors with quick response-recovery characteristics at a temperature of 250 °C for undoped and 225 °C for A. indica dye-doped ZnO thin films. The interaction of A. indica dye extracts helps to decrease the operating temperature and increased the response and recovery rates of the sensor, which may be due to an increase in the specific surface area, resulting in adsorption of more oxygen and hence high response results.     

The effect of hydrothermal growth temperature on preparation and photoelectrochemical performance of ZnO nanorod array films

Highly oriented ZnO nanorod arrays with controlled diameter and length, narrow size distribution and high orientation consistency have been successfully prepared on ITO substrates at different growth temperatures by using a simple hydrothermal method. XRD results indicate that the nanorods are high-quality single crystals growing along [001] direction with a high consistent orientation perpendicular to the substrate. SEM images show that the nanorods have average diameters of about 30-70 nm by changing growth temperature. The thin films consisting of ZnO nanorods with controlled orientation onto ITO substrates allow a more efficient transport and collection of photogenerated electrons through a designed path. For a sandwich-type cell, the relatively high overall solar energy conversion efficiency reaches about 2.4% when the growth temperature is at 95 °C.     

Formation of Superhydrophobic-Superhydrophilic Pattern on Flowerlike Alumina Thin Film by the Sol-Gel Method

We have prepared superhydrophobic surfaces which become superhydrophilic by heat-treatment at 500°C or irradiation of UV-light. When hydrolyzed fluoroalkyltrimethoxysilane (FAS) was coated on Al₂O₃ gel film with a roughness of 20 to 50 nm, the films showed superhydrophobicity and high transparency; the contact angle for water of the film was 165° and the transmittance for the visible light was higher than 92%. When the FAS-coated thin films were heat-treated at temperatures higher than 500°C, the films became superhydrophilic; the contact angle for water on the films was smaller than 5°. Thin films of amorphous TiO₂ or anatase TiO₂ were coated between Al₂O₃ gel and FAS layer, and the contact angle for water was also about 160°. UV irradiation using high-pressure mercury lamp on these films resulted in the contact angle to be smaller than 5°. When UV light was irradiated through a photomask, superhydrophobic-superhydrophilic micropatterns applicable as a stamper for printing or a substrate of micro-optical components were successfully obtained on the films.