聚合物微环谐振波分复用器传输特性的理论分析

根据耦合模理论,给出了1×N信道微环谐振波分复用器(MRRWM)的光强传递函数通用公式,并分析了微环谐振波分复用器的传输特性。利用参量优化结果,在中心工作波长约为 1.55μm、波长间隔约 5.6 nm的情况下,对1×8信道硅基聚合物微环谐振波分复用器进行了数值模拟。计算结果表明,该器件具有以下优良的性能:分波光谱准确,自由光谱区约为18 nm,对于半径10μm以上的微环弯曲损耗很小,且器件的插入损耗主要由波导的传输损耗决定,振幅耦合比率为0.2时对应的每条竖直输出信道的插入损耗在0.57 dB以下,信道间的串扰小于-18.5 dB,输出谐振峰3 dB带宽可达0.25 nm,最小背景光的强度约为3.8×10-4。     

聚合物微环谐振器电光开关阵列的优化与模拟

利用耦合模理论、电光调制理论和微环谐振理论,提出了一个聚合物微环谐振器电光开关阵列的模型.该器件由N-1个微环和N条平行信道构成,在微环上施加不同方式的驱动电压,可以实现N条信道的开关功能.以7微环8信道结构为例,在1550 nm谐振波长下对该器件进行了优化和模拟.结果表明,微环波导芯的截面尺寸为1.7μm×1.7μm,波导芯与电极间的缓冲层厚度为2.5 μm,电极厚度为0.2μm,微环半径为13.76 μm,微环与信道间的耦合间距为0.14μm,输出光谱的3 dB带宽约为0.05 nm,开关电压约为8.1 V左右,插入损耗约为0.23～4.6 dB,串扰小于-20 dB.     

基于绝缘硅的微环谐振可调谐滤波器

采用电子束光刻和感应耦合等离子刻蚀等工艺,研制了一种基于绝缘硅材料的的微环谐振可调谐滤波器.滤波器微环半径为5μm左右,波导截面尺寸为(350～500 nm)×220 nm不等.测试结果表明,波导宽度为450 nm时器件性能最为理想,其自由频谱宽度为16.8 nm,1.55μm波长附近的消光比为22.1 dB.通过对微...     

聚合物串联耦合双环电光开关的优化

利用耦合模理论、电光调制理论和微环谐振理论,提出一个聚合物串联耦合双环电光开关器件模型,在1.55 μm谐振波长下对该器件进行了模拟和优化.结果为：微环波导芯截面尺寸为1.6×1.6 μm2,波导芯与电极间的限制层厚度为1.6 μm,电极厚度为0.15 μm,微环半径为15.2 μm,微环与信道间的耦合间距为0.14 μm,微环与微环间的耦合间距为0.6 μm,输出光谱的3 dB带宽约为0.06 nm,开关电压约为6 V左右,插入损耗约为2.2 dB,串扰约为－20 dB.所设计的双环电光开关较单环型电光开关不仅输出光谱更加平坦陡峭,非谐振光更弱,而且开关电压更低.     

1×N信道聚合物微环谐振器电光开关阵列的开关特性

利用耦合模理论、电光调制理论和微环谐振理论,提出了一个完善合理的聚合物微环谐振器电光开关阵列模型.该器件由1条水平信道、N条竖直信道和N个微环构成,在微环上施加不同方式的驱动电压,可以实现N+1条信道的开关功能.以1×8信道结构为例,在1 550 nm谐振波长下对该器件进行了优化设计和模拟分析.其结果是:微环波导芯的截面尺寸为1.7×1.7 μm2,波导芯与电极间的缓冲层厚度为2.5 μm,电极厚度为0.2 μm,微环半径为13.76 μm,微环与信道间的耦合间距为0.14 μm,输出光谱的3 dB带宽约为0.05 nm,开关电压约为12.6 V,插入损耗约为0.67～1.26 dB,串扰小于-20 dB,开关时间约为11.35 ps.     

光子晶体耦合缺陷波导两通道解波分复用器

提出了一种新型两通道光子晶体解波分复用器.首先使用平面波展开法分析了耦合缺陷波导的特性.接着对双耦合缺陷波导之间的耦合效应进行分析.然后,利用耦合效应设计了一种高效的解波分复用器,使用有限时域差分法研究了不同波长的光在解波分复用器中的传输特性,并计算出了电场分布图.仿真结果表明,该种结构可以实现波长分别为1 266nm和1 311nm两种光波的解波分复用.由于耦合缺陷波导具有更小的群速度,此种结构较基于线缺陷波导耦合的解波分复用器具有更小的耦合长度,从而减小了系统的体积.     

光纤干涉型波分复用器件的研究

利用耦合理论，分析了马赫－陈德尔（Ｍａｃｈ－Ｚｅｈｎｄｅｒ）干涉型波分复用器的复用间隔，波长隔离度及输出功率等特性，讨论了它的温度稳定性，并对其波长调谐性进行了分析与实验。     

基于三角晶格光子晶体谐振腔的双通道解波分复用器

提出了一种基于三角晶格二维光子晶体解波分复用器。该器件主体由线缺陷波导、环形谐振腔及点缺陷微腔构成。使用平面波展开法研究了线缺陷波导的特性,给出了线缺陷波导的能带图,对局部器件微调后进行大量的性能仿真以及对整体器件进行性能仿真,选择合适的器件参数,并使用时域有限差分法研究了不同波长的光在解波分复用器中的传输特性,并给出了电场分布图。仿真结果表明,该种结构可以实现波长分别为1271nm和1291nm两种光波的解波分复用。采用6个额外的介质柱,提高了环形腔的透射率;并通过在入射波导的入射口处增加三对介质柱,提高了波导的出射效率,从而整体上提高了双通道解波分复用器的输出效率。     

聚合物微环电光开关的模拟和优化

利用耦合模理论、电光调制理论和微环谐振理论,提出一个完善合理的聚合物微环电光开关的器件模型,并给出了可用以分析微环谐振过程的光强传递函数,据此在谐振波长1 550 nm下对该器件进行了模拟和优化.结果表明：微环波导芯截面尺寸为1.8×1.8 μm2,波导芯与电极间的限制层厚度为1.1 μm,电极厚度为0.15 μm,微环半径为15.2 μm,微环与信道间的耦合间距为0.16 μm,光绕微环转300 圈即可形成稳定的谐振状态,此时的谐振时间约为147.4 ps.不加电压时,下信道的插入损耗约为0.8 dB,上信道的串扰约为－26 dB;当取工作电压等于19.7 V为开关电压时,上信道的插入损耗约为0.34 dB,下信道的串扰约为－20 dB.     

1×|N 信道聚合物微环谐振器电光开关阵列的开关特性

利用耦合模理论、电光调制理论和微环谐振理论,提出了一个完善合理的聚合物微环谐振器电光开关阵列模型.该器件由1条水平信道、N条竖直信道和N个微环构成,在微环上施加不同方式的驱动电压,可以实现N＋1条信道的开关功能.以1×8信道结构为例,在1 550 nm谐振波长下对该器件进行了优化设计和模拟分析.其结果是：微环波导芯的截面尺寸为1.7×1.7 μm2,波导芯与电极间的缓冲层厚度为2.5 μm,电极厚度为0.2 μm,微环半径为13.76 μm,微环与信道间的耦合间距为0.14 μm,输出光谱的3 dB带宽约为0.05 nm,开关电压约为12.6 V,插入损耗约为0.67~1.26 dB,串扰小于－20 dB,开关时间约为11.35 ps.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.