Magnetic molecularly imprinted polymer nanoparticles for the solid-phase extraction of paracetamol from plasma samples,followed its determination by HPLC

We are presenting magnetic molecularly imprinted polymer nanoparticles (m-MIPs) for solid-phase extraction and sample clean-up of paracetamol. The m-MIPs were prepared from magnetite (Fe₃O₄) as the magnetic component, paracetamol as the template, methacrylic acid as a functional monomer, and 2-(methacrylamido) ethyl methacrylate as a cross-linker. The m-MIPs were then characterized by transmission electron microscopy, FT-IR spectroscopy, X-ray diffraction and vibrating sample magnetometry. The m-MIPs were applied to the extraction of paracetamol from human blood plasma samples. Following its elution from the column loaded with the m-MIPs with an acetonitrile-buffer (9:1) mixture, it was submitted to HPLC analysis. Paracetamol can be quantified by this method in the 1 μg L^?1 to 300 μg L^?1 concentration range. The limit of detection and limit of quantification in plasma samples are 0.17 and 0.4 μg L^?1. The preconcentration factor of the m-MIPs is 40. The HPLC method shows good precision (4.5 % at 50 μg L^?1 levels) and recoveries (between 83 and 91 %) from spiked plasma samples. Figure

We are presenting magnetic molecularly imprinted polymer nanoparticles (m-MIPs) for solid-phase extraction and sample clean-up of paracetamol. The m-MIPs were applied to the extraction of paracetamol from human blood plasma samples     

An automated headspace solid-phase microextraction followed by gas chromatography–mass spectrometry method to determine macrocyclic musk fragrances in wastewater samples

A fully automated method has been developed for determining eight macrocyclic musk fragrances in wastewater samples. The method is based on headspace solid-phase microextraction (HS-SPME) followed by gas chromatography–mass spectrometry (GC-MS). Five different fibres (PDMS 7 μm, PDMS 30 μm, PDMS 100 μm, PDMS/DVB 65 μm and PA 85 μm) were tested. The best conditions were achieved when a PDMS/DVB 65 μm fibre was exposed for 45 min in the headspace of 10 mL water samples at 100 °C. Method detection limits were found in the low ng L^?1 range between 0.75 and 5 ng L^?1 depending on the target analytes. Moreover, under optimized conditions, the method gave good levels of intra-day and inter-day repeatabilities in wastewater samples with relative standard deviations (n?=?5, 1,000 ng L^?1) less than 9 and 14 %, respectively. The applicability of the method was tested with influent and effluent urban wastewater samples from different wastewater treatment plants (WWTPs). The analysis of influent urban wastewater revealed the presence of most of the target macrocyclic musks with, most notably, the maximum concentration of ambrettolide being obtained in WWTP A (4.36 μg L^?1) and WWTP B (12.29 μg L^?1), respectively. The analysis of effluent urban wastewater showed a decrease in target analyte concentrations, with exaltone and ambrettolide being the most abundant compounds with concentrations varying between below method quantification limit (<MQL) and 2.46 μg L^?1.

Rapid screening and detection of XOD inhibitors from S. tamariscina by ultrafiltration LC-PDA–ESI-MS combined with HPCCC

Xanthine oxidase (XOD) catalyzes the metabolism of hypoxanthine and xanthine to uric acid, the overproduction of which could cause hyperuricemia, a risk factor for gout. Inhibition of XOD is a major treatment for gout, and biflavonoids have been found to act as XOD-inhibitory compounds. In this study, ultrafiltration liquid chromatography with photodiode-array detection coupled to electrospray-ionization tandem mass spectrometry (UF-LC-PDA–ESI-MS) was used to screen and identify XOD inhibitors from S. tamariscina. High-performance counter-current chromatography (HPCCC) was used to separate and isolate the active constituents of these XOD inhibitors. Furthermore, ultrahigh-performance liquid chromatography (UPLC) and triple-quadrupole mass spectrometry (TQ-MS) was used to determine the XOD-inhibitory activity of the obtained XOD inhibitors, and enzyme kinetics was performed with Lineweaver–Burk (LB) plots using xanthine as the substrate. As a result, two compounds in S. tamariscina were screened as XOD inhibitors: 65.31 mg amentoflavone and 0.76 mg robustaflavone were isolated from approximately 2.5 g?S. tamariscina by use of HPCCC. The purities of the two compounds obtained were over 98 % and 95 %, respectively, as determined by high-performance liquid chromatography (HPLC). Lineweaver–Burk plot analysis indicated that amentoflavone and robustaflavone were non-competitive inhibitors of XOD, and the IC ₅₀ values of amentoflavone and robustaflavone for XOD inhibition were 16.26 μg mL^?1 (30.22 μmol L^?1) and 11.98 μg mL^?1 (22.27 μmol L^?1), respectively. The IC ₅₀ value of allopurinol, used as the standard, was 7.49 μg mL^?1 (46.23 μmol L^?1). The results reveal that the method for systematic screening, identification, and isolation of bioactive components in S. tamariscina and for detecting their inhibitory activity using ultrafiltration LC–ESI-MS, HPCCC, and UPLC–TQ-MS is feasible and efficient, and could be expected to extend to screening and separation of other enzyme inhibitors. Graphical Abstract

?     

Chitosan-poly(m-phenylenediamine)@Fe3O4 nanocomposite for magnetic solid-phase extraction of polychlorinated biphenyls from water samples

A extraction medium based on chitosan-poly(m-phenylenediamine) (CS-PPD) @Fe₃O₄ nanocomposite was synthesized by chemical polymerization of m-phenylenediamine in the presence of chitosan coated magnetic nanocomposite, and for the first time, used as the sorbent for the magnetic solid-phase extraction (MSPE) of seven polychlorinated biphenyls (PCB28, PCB52, PCB101, PCB118, PCB138, PCB153, and PCB180) at trace levels in water samples. Gas chromatography-triple quadrupole mass spectrometry (GC-MS/MS) was used for PCBs quantification and detection. Several factors related to MSPE efficiencies, such as type and amount of sorbent, extraction time, sample pH, and desorption conditions were investigated. Under the optimized conditions, an excellent linearity was observed in the range of 1.0–200 ng L^–1 for PCB180, 0.5–200 ng L^–1 for the other six PCBs with the correlation coefficients ranging from 0.9954 to 0.9993. The good recoveries at spiked levels of 10.0, 20.0, and 50.0 ng L^–1 were obtained in the range of 94 %–108 %, and the coefficients of variations were less than 6 %. The proposed method was feasible, rapid, and easy to operate for the trace analysis of the PCBs in local aquaculture water, livestock breeding water, and sewage water samples. Graphical Abstract

Fig. 1 Schematic diagram for the preparation of chitosan–poly(m-phenylenediamine) @Fe₃O₄ nanocomposite.     

Polyoxotungstate nanoclusters supported on silica as an efficient solid-phase microextraction fiber of polycyclic aromatic hydrocarbons

A highly porous silica-supported tungstophosphoric acid (PW) nanocluster was prepared for use in solid-phase microextraction (SPME) of polycyclic aromatic hydrocarbons (PAHs). The PWs represent a class of discrete transition metal-oxide nanoclusters and their structures resemble discrete fragments of metal-oxide structures of definite size and shape. Transition metal-oxide nanoclusters display large structural diversity, and their monodisperse sizes can be tuned from several Ångstroms up to 10 nm. The highly porous silica-supported tungstophosphoric acid nanocluster material is found to be capable of efficiently extracting PAHs from aqueous sample solutions. The nanomaterial was immobilized on a stainless steel wire for fabrication of the SPME fiber. Following thermal desorption, the PAHs were quantified by GC-MS. Analytical merits include limits of detection that range from 0.02 to 0.1 pg mL^?1 and a dynamic range as wide as from 0.001 to 100 ng mL^?1. Under optimum conditions, the repeatability for one fiber (n?=?3), expressed as the relative standard deviation, is between 4.3 % and 8.6 %. The method is simple, rapid, and inexpensive. The thermal stability of the fiber and the high relative recovery make this method superior to conventional methods of extraction.

The highly porous silica-supported tungstophosphoric acid nanocluster material is found to be capable of efficiently extracting PAHs from aqueous sample solutions. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. Following thermal desorption, the PAHs were quantified by GC-MS.     

The Development and Validation of a Stability-Indicating UHPLC-DAD Method for Determination of Perindopril l-Arginine in Bulk Substance and Pharmaceutical Dosage Form

A stability-indicating ultra-high-performance liquid chromatography (UHPLC) method with a diode array detector was developed and validated for the determination of cis/trans isomers of perindopril l-arginine in bulk substance and pharmaceutical dosage form. The separation was achieved on a Poroshell 120 Hilic (4.6 × 150 mm, 2.7 µm) column using a mobile phase composed of acetonitrile–0.1 % formic acid (20:80 v/v) at a flow rate of 1 mL min^?1. The injection volume was 5.0 µL and the wavelength of detection was controlled at 230 nm. The selectivity of the UHPLC-DAD method was confirmed by determining perindopril l-arginine in the presence of degradation products formed during acid–base hydrolysis and oxidation as well as degradation in the solid state, at an increased relative air humidity and in dry air. The method’s linearity was investigated in the ranges 0.40–1.40 µg mL^?1 for isomer I and 0.40–2.40 µg mL^?1 for isomer II of perindopril l-arginine. The UHPLC-DAD method met the precision and accuracy criteria for the determination of the isomers of perindopril l-arginine. The limits of detection and quantitation were 0.1503 and 0.4555 µg mL^?1 for isomer I and 0.0356 and 0.1078 µg mL^?1 for isomer II, respectively.     

Highly sensitive SERS probe for mercury(II) using cyclodextrin-protected silver nanoparticles functionalized with methimazole

We have developed a surface-enhanced Raman scattering (SERS) probe for the determination of mercury(II) using methimazole-functionalized and cyclodextrin-coated silver nanoparticles (AgNPs). These AgNPs in pH 10 solution containing sodium chloride exhibit strong SERS at 502 cm^?1. Its intensity strongly decreases in the presence of Hg(II). This effect serves as the basis for a new method for the rapid, fast and selective determination of trace Hg(II). The analytical range is from 0.50 μg L^?1 to 150 μg L^?1, and the limit of detection is 0.10 μg L^?1. The influence of 11 metal ions commonly encountered in environmental water samples was found to be quite small. The method was applied to the determination of Hg(II) in spiked water samples and gave recoveries ranging from 98.5 to 105.2 % and with relative standard deviations of <3.5 % (n?=?5). The total analysis time is <10 min for a single sample.

Magnetite-doped eggshell membrane as a magnetic sorbent for extraction of aluminum(III) ions prior to their fluorometric determination

We have explored the feasibility of using a magnetite-doped eggshell membrane as a magnetic solid phase extraction sorbent for the separation of aluminum ion from aqueous solutions. The sorbent was characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. A fast, simple and non-expensive method was then developed for the determination of trace quantities of Al(III) in water and food samples by combining magnetic solid phase extraction with fluorometric quantitation via its highly fluorescent complex with 8-hydroxyquinoline. The effects of pH value, amount of sorbent, sample volume, elution conditions and interfering ions on extraction were optimized. Under optimum conditions, the calibration graph extends from 0.5 to 65.0 μg L^?1, the limit of detection is 0.2 μg L^?1, and the enrichment factor is 84. The method was validated by the successful analysis of a standard reference material (NIST SRM 1549; nonfat milk powder) and applied to the determination of Al(III) in several waters, black tea, tomato paste and cocoa powder samples. Figure

Synthesis and application of magnetite-doped eggshell membrane for the separation of aluminum(III) ions from aqueous solutions is shown. After extraction for 5 min, the sorbent was gathered under an external magnetic field and the clear supernatant was directly decanted. The enriched analyte was then eluted from the sorbent prior to determination.     

Determination of Pt and Pd in particles emitted from automobile exhaust catalysts using ion-exchange matrix separation and voltammetric detection

We report on the ion-exchange separation of Pt and Pd from the main elements emitted from catalysts of gasoline-fueled cars by exploiting the selective chelating ion exchanger Lewatit MonoPlus TP-214. Pt and Pd were then eluted with a recovery of 92% and 96%, respectively, using an acidified solution of thiourea, and the eluent was analyzed by sequential voltammetry. The detection limits are 0.04 μg L^?1 and 1 μg L^?1 for Pt and Pd, respectively, and the relative standard deviation is about 4.0% (for n?=?10). The procedure was successfully applied to particles emitted from automobile exhaust catalysts of four capacity engine vehicles. Graphite furnace atomic absorption spectrometry was also employed for reasons of comparison. Emission by four vehicles with 1400, 2600, 3200, and 4800 cc engines, respectively, ranged from 19 to 28 ng km^?1 for Pt, and from 102 to 150 ng km^?1 for Pd.

Transparent poly(thiourethane-urethane)s based on dithiol chain extender

New segmented poly(thiourethane-urethane)s (PTU-Us) (with hard-segment content of 30–60 mass%) were synthesized by a one-step melt polymerization from poly(oxytetramethylene) diol of \( \overline{M}_{n} \)  = 1,000 g mol^?1 or \( \overline{M}_{n} \)  = 2,000 g mol^?1 or poly(hexamethylene carbonate) diol of \( \overline{M}_{n} \)  = 860 g mol^?1 as soft segments, 1,1′-methanediylbis(4-isocyanatocyclohexane) (Desmodur W ^®) and (methylenedi-1,4-phenylene)dimethanethiol as a chain extender. The PTU-Us were examined by FTIR, GPC, XRD, DSC, TG, Shore hardness, and tensile testing. Moreover, refractive index, transparency, adhesive properties, and resistance to bacteria and fungi were determined for selected polymers. The obtained high-molar-mass amorphous polymers showed elastomeric or plastic properties. Their T _gs were in the range from ?70 to 58 °C. The PTU-Us with the polycarbonate soft segments demonstrated a better segmental miscibility (higher T _gs), transparency as well as generally higher tensile strength and hardness than those with the polyether soft segments. All the synthesized PTU-Us showed a relatively good thermal stability. The temperature of 1 % mass loss of all PTU-Us was in the range of 236–255 °C. The introduction of thiourethane linkages to polyurethane chain caused increase of the adhesive strength on copper–polymer junction and refractive index values. From the microbial studies, it was found that the obtained polymers had delayed the growth of Gram-positive bacteria.     

Separation and Sensitive Analysis of Chlorophenols by MEEKC

A new microemulsion electrokinetic chromatographic method has been established for separation and sensitive analysis of the three chlorophenols 2-chlorophenol, 4-chlorophenol, and 2,4-dichlorophenol. The optimum microemulsion system was 15 mM SDS, 112 mM n-butanol, and 10 mM n-octane in 20 mM sodium tetraborate (pH 9.0). Under the optimum conditions, baseline separation was achieved within 8 min. The method was used for analysis of a real water sample previously pretreated by SPE. The linear ranges, precision of migration time and peak area, and limits of detection (LOD) were in the ranges of 0.5–50 μg L^?1, 4.85–9.75%, 0.49–0.706% (n = 6), and 0.6–1 μg L^?1, respectively, for the three chlorophenols.     

Titanium dioxide nanoparticle based solid phase extraction of trace Alizarin Violet,followed by its specrophotometric determination

Nanometer-sized titanium dioxide (nano-TiO₂) is shown to be a viable material for the preconcentration of Alizarin Violet (AV, a common dye and biological stain). In the preconcentration step, a 5-ring cyclic ester is formed between the ortho-dihydroxy groups of AV and two hydroxy groups of the titanic acid on the surface of the nano-TiO₂. Under optimized conditions, the adsorption capacity of nano-TiO₂ is?~?20 μg?·?mg^?1, the adsorption efficiency is 98 %. The adsorbed AV can be eluted with 5 mL of 5 mol?·?L^?1 5-sulfosalicylic acid with an elution efficiency of more than 91.8 %. The preconcentration factor is 50 in case of 250 mL samples. Spectrophotometric determination of AV in the eluate gives a linear calibration plot in the range between 18.8 μg?·?L^?1 and 10 mg?·?L^?1 and a detection limit (3 s; for n?=?11) of 18.8 μg?·?L^?1. The method is simple and fast. It was successfully applied to the analysis of AV in spiked natural waters, and recoveries were found to range between 94.2 and 97.3 %.

Nanometer-sized titanium dioxide is a viable material for the preconcentration of Alizarin Violet (AV), before its spectrophotometrical determination. The method is simple and fast. It was successfully applied to the analysis of AV in spiked natural waters, and recoveries were found to range between 94.2 and 97.3 %.     

Production of <Emphasis Type="Italic">R</Emphasis>-Mandelic Acid Using Nitrilase from Recombinant <Emphasis Type="Italic">E. coli</Emphasis> Cells Immobilized with Tris(Hydroxymethyl)Phosphine

Recombinant Escherichia coli cells harboring nitrilase from Alcaligenes faecalis were immobilized using tris(hydroxymethyl)phosphine (THP) as the coupling agent. The optimal pH and temperature of the THP-immobilized cells were determined at pH 8.0 and 55 °C. The half-lives of THP-immobilized cells measured at 35, 40, and 50 °C were 1800, 965, and 163 h, respectively. The concentration of R-mandelic acid (R-MA) reached 358 mM after merely 1-h conversion by the immobilized cells with 500 mM R,S-mandelonitrile (R,S-MN), affording the highest productivity of 1307 g L^?1 day^?1 and the space-time productivity of 143.2 mmol L^?1 h^?1 g^?1. The immobilized cells with granular shape were successfully recycled for 60 batches using 100 mM R,S-MN as substrate at 40 °C with 64% of relative activity, suggesting that the immobilized E. coli cells obtained in this study are promising for the production of R-MA.     

Determination of methylisothiocyanate in soil and water by HS-SPME followed by GC–MS–MS with a triple quadrupole

Methylisothiocyanate (MITC) is the main degradation product of metam sodium, a soil disinfectant widely used in agriculture, and is responsible for its disinfectant properties. Because MITC is highly toxic and volatile, metam sodium has to be applied in a manner that tries to reduce atmospheric emissions but still maintains adequate concentration of MITC in soil to ensure its disinfectant effect. Thus, monitoring of MITC concentrations in soil is required, and to this end sensitive, fast, and reliable analytical methods must be developed. In this work, a headspace solid-phase microextraction (HS-SPME) method was developed for MITC determination in water and soil samples using gas chromatography-tandem mass spectrometry (GC–MS–MS) with a triple-quadrupole analyzer. Two MS–MS transitions were acquired to ensure the reliable quantification and confirmation of the analyte. The method had linear behavior in the range tested (0.026–2.6 ng mL^?1 in water, 1–100 ng g^?1 in soil) with r ² over 0.999. Detection limits were 0.017 ng mL^?1 and 0.1 ng g^?1 in water and soil, respectively. Recoveries for five replicates were in the range 76–92 %, and RSD was below 7 % at the two spiking levels tested for each matrix (0.1 and 1 ng mL^?1 for water, 4 and 40 ng g^?1 for soil). The potential of using multiple HS-SPME for analyzing soil samples was also investigated, and its feasibility for quantification of MITC evaluated. The developed HS-SPME method was applied to soil samples from experimental plots treated with metam sodium following good agriculture practices. Figure

?     

Determination of chlorobenzenes in water samples based on fully automated microextraction by packed sorbent coupled with programmed temperature vaporization–gas chromatography–mass spectrometry

A fully automated method consisting of microextraction by packed sorbent (MEPS) coupled directly to programmed temperature vaporizer–gas chromatography–mass spectrometry (PTV–GC–MS) has been developed to determine the 12 chlorobenzene congeners (chlorobenzene; 1,2-, 1,3-, and 1,4-dichlorobenzene; 1,2,3-, 1,2,4-, and 1,3,5-trichlorobenzene; 1,2,3,4-, 1,2,3,5-, and 1,2,4,5-tetrachlorobenzene; pentachlorobenzene; and hexachlorobenzene) in water samples. The effects of the variables on MEPS extraction, using a C18 sorbent, and the instrumental PTV conditions were studied. The internal standard 1,4-dichlorobenzene d4 was used as a surrogate. The proposed method afforded good reproducibility, with relative standard deviations (RSD %) lower than 12 %. The limits of detection varied between 0.0003 μg L^?1 for 1,2,3,4-tetrachlorobenzene and 0.07 μg L^?1 for 1,3- and 1,4-dichlorobenzene, while those of quantification varied between 0.001 μg L^?1 and 0.2 μg L^?1 for the same compounds. Accuracy of the proposed method was confirmed by applying it to the determination of chlorobenzenes in different spiked water samples, including river, reservoir, and effluent wastewater.

Solid-phase microextraction/gas chromatography–mass spectrometry method optimization for characterization of surface adsorption forces of nanoparticles

A complete characterization of the different physico-chemical properties of nanoparticles (NPs) is necessary for the evaluation of their impact on health and environment. Among these properties, the surface characterization of the nanomaterial is the least developed and in many cases limited to the measurement of surface composition and zetapotential. The biological surface adsorption index approach (BSAI) for characterization of surface adsorption properties of NPs has recently been introduced (Xia et al. Nat Nanotechnol 5:671–675, 2010; Xia et al. ACS Nano 5(11):9074–9081, 2011). The BSAI approach offers in principle the possibility to characterize the different interaction forces exerted between a NP's surface and an organic—and by extension biological—entity. The present work further develops the BSAI approach and optimizes a solid-phase microextraction gas chromatography–mass spectrometry (SPME/GC-MS) method which, as an outcome, gives a better-defined quantification of the adsorption properties on NPs. We investigated the various aspects of the SPME/GC-MS method, including kinetics of adsorption of probe compounds on SPME fiber, kinetic of adsorption of probe compounds on NP's surface, and optimization of NP's concentration. The optimized conditions were then tested on 33 probe compounds and on Au NPs (15 nm) and SiO₂ NPs (50 nm). The procedure allowed the identification of three compounds adsorbed by silica NPs and nine compounds by Au NPs, with equilibrium times which varied between 30 min and 12 h. Adsorption coefficients of 4.66?±?0.23 and 4.44?±?0.26 were calculated for 1-methylnaphtalene and biphenyl, compared to literature values of 4.89 and 5.18, respectively. The results demonstrated that the detailed optimization of the SPME/GC-MS method under various conditions is a critical factor and a prerequisite to the application of the BSAI approach as a tool to characterize surface adsorption properties of NPs and therefore to draw any further conclusions on their potential impact on health. Graphical Abstract

The basic principle of SPME/GC-MS method for characterization of nanoparticles surface adsorption forces     

Electrochemically controlled solid-phase micro-extraction of proline using a nanostructured film of polypyrrole, and its determination by ion mobility spectrometry

We report on a fast, simple and accurate method for the determination of proline in urine samples by employing a nanostructured film of conducting polypyrrole for electrochemically controlled solid-phase microextraction, and ion mobility spectrometry (IMS) for detection. This method has the advantages of simple sample preparation and a sensitivity of IMS to proline that is higher than that for other amino acids. The calibration curve is linear in the range of 0.5–60 μg L^?1 (4–521 nmol L^?1), and the detection limit is 0.2 μg L^?1. The electrochemical potentials for uptake and release were optimized. The method was successfully applied to the clean-up and quantitation of trace amounts of proline in urine samples.

A polyaniline-magnetite nanocomposite as an anion exchange sorbent for solid-phase extraction of chromium(VI) ions

This work describes a novel polyaniline-magnetite nanocomposite and its application to the preconcentration of Cr(VI) anions. The material was obtained by oxidative polymerization of aniline in the presence of magnetite nanoparticles. The parameters affecting preconcentration were optimized by a Box-Behnken design through response surface methodology. Extraction time, amount of magnetic sorbent and pH value were selected as the main factors affecting sorption. The sorption capacity of the sorbent for Cr(VI) is 54 mg g^?1. The type, volume and concentration of the eluents, and the elution time were selected as main factors in the optimization study of the elution step. Following sorption and elution, the Cr(VI) ions were reacted with diphenylcarbazide, and the resulting dye was quantified by HPLC with optical detection at 546 nm. The limit of detection is 0.1 μg L^?1, and all the relative standard deviations are <6.3 %. The nanocomposite was successfully applied to the rapid extraction and determination of trace quantities of Cr(VI) ions in spiked water samples. Figure

A schematic procedure of magnetic solid phase extraction     

Development of novel sol–gel coatings by chemically bonded ionic liquids for stir bar sorptive extraction—application for the determination of NSAIDS in real samples

In this work, a novel ionic liquid (IL) chemically bonded sol–gel coating was prepared for stir bar sorptive extraction (SBSE) of nonsteroidal anti-inflammatory drugs (NSAIDs) followed by high-performance liquid chromatography-ultraviolet detection (HPLC-UV). By using γ-(methacryloxypropyl)trimethoxysilane (KH-570) as a bridging agent, 1-allylimidazolium tetrafluoroborate ([AIM][BF₄]) was chemically bonded onto the bare stir bar, and the prepared IL-bonded sol–gel stir bar coating showed higher extraction efficiency and better adsorption/desorption kinetics for target NSAIDs over other polydimethylsiloxane (PDMS)-based or monolithic stir bar coatings. The mechanical strength and durability (chemical/thermal stability) of the prepared IL-bonded sol–gel coating were excellent. The influencing factors of SBSE, such as sample pH, salt effect, stirring rate, extraction time, desorption solvent, and desorption time, were optimized, and the analytical performance of the developed SBSE-HPLC-UV method was evaluated under the optimized conditions. The limits of detection (LODs) of the proposed method for three NSAIDs were in the range of 0.23–0.31 μg L^?1, and the enrichment factors (EFs) were in the range of 51.6–56.3 (theoretical enrichment factor was 100). The reproducibility was also investigated at concentrations of 5, 20, and 100 μg L^?1, and the relative standard deviations (RSDs) were found to be less than 9.5, 7.5, and 7.6 %, respectively. The proposed method was successfully applied for the determination of NSAIDs in environmental water, urine, and milk samples. Graphical Abstract

?     

Cold vapor generation of Zn based on dielectric barrier discharge induced plasma chemical process for the determination of water samples by atomic fluorescence spectrometry

A new plasma chemical vapor generation (plasma-CVG) method for Zn was developed by dielectric barrier discharge (DBD). The dissolved Zn ions was readily converted to volatile species by DBD plasma in the presence of hydrogen and then, the generated Zn vapor, Zn⁰, was detected by cold vapor atomic fluorescence spectrometry (AFS). It eliminated the use of unstable tetrahydroborate-reducing reagent and high-purity acids. The operating conditions for the DBD plasma-CVG system were optimized for the efficient vapor generation of Zn. In addition, possible interferences from coexisting ions on the plasma-CVG of Zn were also examined. No appreciable matrix interference was found from most of the examined ions at concentration of 1 mg L^?1. However, severe depression of the Zn vapor generation efficiency was observed in the presence of ions at 10 mg L^?1. Under the optimal conditions, the limit of detection (LOD) was calculated to be 0.2 μg L^?1; good repeatability (relative standard deviation (RSD)?=?2.6 %, n?=?11) was obtained for a 20 Zn μg L^?1 standard. The accuracy of the proposed method was validated though analysis of Zn in reference material of simulated natural water sample GSB07-1184-2000 and the determined result was in good agreement with the reference value. The proposed method has also been successfully applied to the determination of Zn in Changjiang River water, Wuhan East Lake water, and Wuhan tap water samples. It provides an alternative green vapor generation method for Zn. Figure

?