纳米金属粉对高氯酸铵热分解动力学的影响

The thermal decomposition characteristics of general ammonium perchlorate (g-AP) influenced by the addition of aluminum, nickel with different particle sizes (general and nano) are studied by TG and DSC. The results show that aluminum powders (both general and nano size) are nearly uninfluenced. Nano nickel powders have the greatest influence on the decomposition properties of g-AP among metal powders. Such accelerating effects of nanonickel powders are more apparent on the stage of high temperature decomposition than low temperature decomposition of g-AP and will be weakened with the decrease of the content of nanonickel. Nanonickel powders are also more effective than super fine nickel powders on accelerating the thermal decomposition of superfine AP (s-AP). The kinetic parameters of the thermal decomposition of s-AP and mixture of s-AP and nano nickel powders are obtained from the TG-DTG curves bythe integral method based on the Coats-Red fern equation. Nanonickel powders reduce the apparent activation energy of the thermal decomposition of s-AP from 157.9 kJ/mol to 134.9 kJ/mol. The most probable mechanism functions of the thermal decomposition reaction for s-AP and mixture of s-AP and nano nickel powders both belong to systems of Avrami-Erofeev equations. The mechanism of such accelerating effects has been discussed.     

纳米铜粉对高氯酸铵热分解的影响

The decomposition behaviour of ammonium perchlorate (AP) has been investigated in the presence of Cu nanopowder by DTA. The results show that nanometer Cu powder decreased the first and second thermal decomposition temperature of AP by 35.1 ℃ and 130.2 ℃, respectively, and the DTA heat release of AP in the presence of Cu nanopowders increased to 1.20 kJ·g^-1, showing good catalytic effect on the thermal decomposition of AP. The catalytic effect of Cu micron-size powder on the thermal decomposition of AP was less than that of Cu nanopowder. With the increase in content, Cu nanopowder enhanced its catalytic effect on the high temperature decomposition of AP, however, it weakened its catalytic effect on the low temperature decomposition of AP. The mechanism of catalysis for the thermal decomposition of AP is as follows: (1) metal oxider acts as the intermedium in the process of election tranfer, (2) Cu nanopowder reacts with the decomposed product of AP, (3) Cu nanopowder has special surface effect.     

纳米NdCoO3催化高氯酸铵热分解的DSC/TG-MS研究

采用微乳液法制备了立方晶系的NdCoO3纳米晶.利用DSC/TG-MS研究了NdCoO3对AP热分解的催化作用.结果表明,在NdCoO3的催化作用下,AP的热分解反应峰值温度下降了113℃,表观分解反应热从655 J·g-1增加到1 363 J·g-1,分解的气相产物主要有NH3,H2O,O2,HCl,N2O,NO,NO2和Cl2.在金属氧化物表面吸附生成超氧化离子(O2-)和氧离子(O-,O2-),这是加速AP分解反应的主要原因.加入NdCoO3催化AP热分解,由于对氨的氧化深度不同而导致分解放热量的增加.     

铜/纳米金刚石复合物的结构及其对高氯酸铵热分解的催化作用

Nano-Copper and Cu/UDD (ultradispersed diamond) nanocomposites were separately prepared by reduction of CuCl₂ aqueous solution and that doped with 0.7%(weight percent) of ultra-dispersed diamond. The as prepared nano-crystals were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR) and electron paramagnetic resonance techniques (EPR). It was found that homogeneous nucleation dominated the aqueous reduction reaction at high concentration and the diameter of nano-copper decreased as the reaction time shortened, yet at lower concentration heterogeneous nucleation predominated and the doped UDD functioned as heterogeneous nucleation. Otherwise large number of free-radicals existed in the nano-composites. Both of nano-copper and Cu/UDD nanocomposites were strong catalysts for AP decomposition, with Cu/UDD being a more effective one. The higher decomposition temperature for AP was 119 ℃ lower than that without catalyst. And the exothermic quantity of decomposition was from 590 J·g^-1 to 1 400 J·g^-1 by mix 2% of the Cu/UDD nanocomposites.     

铝粉粒度对高氯酸铵热分解动力学的影响

采用热重-差示扫描量热(TG-DSC)联合技术研究了10.7 μm, 2.6 μm和40 nm铝粉对高氯酸铵(AP)热分解的影响. 结果表明, 铝粉的加入对AP的低温放热峰有抑制作用, 对高温放热分解反应有促进作用, 并且随铝含量的增加和铝粒径的减小这种作用更强烈. 采用多元非线性拟合技术对不同升温速率下TG-DSC实验数据进行拟合, 结果表明, 质量分数为40%的不同粒径铝粉的加入对AP的热分解三阶段(A→B→C→D)反应模型无影响, 但反应机理函数发生了改变. 纯AP, AP/Al(10.7 μm), AP/Al(2.6 μm)及AP/Al(40 nm)的反应机理函数组合分别为C1/D1/D1, C1/D1/D3, C1/D1/D4和C1/D1/F2.     

纳米Co3O4的制备及其对高氯酸铵热分解的催化性能

 选用CoCl2·6H2O分别与NaOH, H2C2O4·2H2O, Na2CO3·10H2O及Na2C2O4组成四个反应体系,通过室温固相反应制备了不同平均粒径的纳米Co3O4, 并用X射线衍射和透射电镜对Co3O4的物相、形貌和粒径大小进行了表征. 结果表明, Co3O4的平均粒径分别为23, 30, 35和150 nm, 大小均匀,分散性好. 还用差热分析法考察了纳米Co3O4对高氯酸铵热分解的催化性能,并与微米Co3O4进行了比较. 结果表明,纳米Co3O4可使高氯酸铵的低温放热峰消失,高温放热峰温度降至323.5 ℃, 降低了128.5 ℃, 表观分解热增加了750 J/g, 达 1265 J/g, 纳米Co3O4对高氯酸铵热分解的催化性能明显好于微米Co3O4.     

纳米CuO：不同形貌的制备及对高氯酸铵热分解催化性能

采用超声法和微波水热法,制备了棒状、球状、梭形和杨桃状纳米CuO粉体。以X-射线粉末衍射仪(XRD)、透射电镜(TEM)手段对各种产物进行了表征。用热分析法考察了不同形貌的纳米CuO对高氯酸铵(AP)分解的催化作用。结果表明,四种形貌的纳米CuO均可强烈催化AP的热分解,而棒状和球状纳米CuO的催化活性更高。与纯高氯酸铵相比,加入棒状纳米CuO后AP的高温分解温度降低了124.4 ℃,加入球形纳米CuO催化剂后高温分解温度降低了122 ℃,且低温分解峰消失。     

Mg2NiH4对高氯酸铵热分解过程的影响

采用置换-扩散法制备了储氢材料Mg2NiH4, 用XRD, ICP和DSC-TG方法对其结构进行了表征. 用热分析法(DSC)研究了Mg2NiH4对高氯酸铵(AP)热分解过程的影响. 研究结果表明, Mg2NiH4对AP热分解过程有较大影响. Mg2NiH4可以显著促进AP的低温热分解过程, 降低高温热分解温度, 使DSC表观分解热明显增大. 随着加入量的增加, Mg2NiH4对AP热分解的催化促进作用增强, 当Mg2NiH4加入的质量分数为30％时, DSC表观分解热最大. 吸氢量越大, 储氢材料对AP的催化促进作用越强. Mg2NiH4催化促进AP分解过程的作用机理为: Mg2NiH4分解释放的H2及Mg和Ni与AP分解产物发生反应.     

多孔纳米CoFe2O4的制备及其对高氯酸铵的热分解催化性能

采用胶晶模板法制备出具有三维多孔结构的纳米CoFe₂O₄。利用X射线衍射仪(XRD)、傅里叶变换红外(FT-IR)光谱仪、扫描电镜(SEM)、透射电镜(TEM)和N₂吸附-脱附对样品的晶型和形貌结构等进行表征,采用差示扫描量热法(DSC)对比研究多孔纳米CoFe₂O₄和球形纳米CoFe₂O₄对高氯酸铵(AP)的热分解性能的影响,并考察这两种催化剂对AP催化热分解的动力学参数。结果显示,制备出的多孔纳米CoFe₂O₄样品具有典型的尖晶石结构,孔径约200 nm;比表面积明显高于40 nm球形CoFe₂O₄,达到55.646 m²·g^-1。DSC测试结果表明：多孔纳米CoFe₂O₄的加入促进了AP的热分解,最高使AP的高温分解峰温降低91.46℃,能量释放最高达1120.88 J·g^-1,是纯AP分解放热量的2.3倍;多孔纳米CoFe₂O₄具有较高的比表面积,能提高催化反应的接触面积,使AP的高温分解峰温度更低,反应活化能较小,从而表现出比球形纳米CoFe₂O₄更高的催化活性。此外,对多孔纳米CoFe₂O₄催化AP的热分解机理进行初步探索,纳米多孔催化剂对气态中间产物的作用促进了AP的热分解。     

纳米LaCoO3的制备及其对高氯酸铵分解的催化性能

以硝酸镧和硝酸钴为原料,通过硬脂酸法制备了纳米LaCoO3。采用红外光谱、X射线衍射、透射电镜等测试手段对产物进行了表征,并用热分析法考察了不同含量的纳米LaCoO3对高氯酸铵热分解的催化作用。结果表明,在600℃下可获得结晶良好的钙钛矿型纳米LaCoO3,粒径约40-60 nm。纳米LaCoO3能强烈催化高氯酸铵的热分解,催化作用随着LaCoO3含量的增加而增强。添加5%的纳米LaCoO3可使高氯酸铵的高温分解温度下降116℃,分解放热量也由2%时的1390 J·g^-1增至1600 J·g^-1。     

纳米Co-B非晶态合金对高氯酸铵分解的催化性能

 利用化学还原法制备了纳米 Co-B 非晶态合金,并用透射电镜、X射线衍射、差示扫描量热和N2吸附表面积测试等技术对样品进行了表征. 运用差热分析研究了纳米 Co-B 非晶态合金对高氯酸铵(AP)分解的催化性能. 结果表明,加入 Co-B 非晶态合金后AP的高低温放热峰相连,合并成一个高而大的放热峰,且峰温有很大程度的降低, 这说明纳米 Co-B 非晶态合金对AP热分解有很好的催化活性. 同时, Co-B 非晶态合金能使AP的表观分解热显著增大.     

镁铜合金储氢材料的制备及对高氯酸铵热分解过程的影响

采用置换-扩散法制备了镁铜合金储氢材料(Mg2Cu-H), 并对其结构进行了表征. 结果表明, Mg2Cu经过氢化得到的镁铜合金储氢材料不是单一晶相, 而是MgCu2和MgH2的混合物. 用热分析法(DSC)研究了镁铜合金储氢材料对固体火箭推进剂常用氧化剂——高氯酸铵(AP)热分解过程的影响. 结果表明, 镁铜合金储氢材料可以显著促进AP的热分解过程, 加快热分解速率, 降低高温热分解温度, 使DSC表观分解热明显增大. Mg2Cu-H对AP热分解过程的促进作用明显强于Mg2Cu. 随着加入量增加, 镁铜合金储氢材料对AP热分解的催化促进作用增强. 探讨了镁铜合金储氢材料促进AP热分解过程的作用机制.     

纳米Cu2O的制备及其对高氯酸铵热分解的催化性能

 以Cu(NO3)2和NaOH为原料,以水合肼为还原剂,通过沉淀法在室温下制备了纳米Cu2O. 采用X射线衍射、透射电镜和X射线光电子能谱等手段对产物进行了表征,并用热分析法考察了不同形貌的纳米Cu2O对高氯酸铵热分解的催化作用. 结果表明,通过改变NaOH溶液的加入量可分别得到长针形和多边形的纳米Cu2O. 通过调节反应物浓度可以将纳米Cu2O粒径控制在19～68 nm. 不同形貌的纳米Cu2O均能强烈催化高氯酸铵的热分解,其中分散性良好的多边形纳米Cu2O的催化活性较高,添加2%的多边形纳米Cu2O可使高氯酸铵的高温分解温度降低103 ℃,分解放热量由590 J/g增至1350 J/g.     

Effects of Aluminum on Thermal Decomposition of Hexogen/Ammonium Perchlorate

Thermogravimetry-differential scanning calorimetry-mass spectrometry-Fourier transform infrared spectrometry（TG-DSC-MS-FTIR） simultaneous analysis was used to study the effects of 10.7 μm and 40 nm Al on the thermal decomposition of the Hexogen/ammonium perchlorate（RDX/AP,1/2,mass ratio） mixture.TG-DSC results show that there are two mass loss processes for the thermal decomposition of RDX/AP/Al.The first one is mainly ascribed to the thermal decomposition of RDX.The reaction rate of RDX/AP/10.7 μm Al is so fast that the apparent activation energy,calculated by model-free Friedman method,is negative,which is the same as that of RDX/AP.30％（mass fraction） 40 nm Al added in RDX/AP change the activation energy from negative to positive value.The second mass loss process of the RDX/AP/A1 mixture is ascribed to the thermal decomposition of AP.This process can be divided into three stages for RDX/AP with and without Al.The kinetics model is not changed in the presence of micro-sized Al,while it is changed from CnB/D1/D1 to CnB/D1/D4 after the addition of 40 nm Al to RDX/AP.The reaction rate constant of the first stage and the end temperature of the second stage decrease,while the end temperatures of the third stage increase in the presence of 40 nm Al.The MS-FTIR results show there is a competition between the formation reactions of HNCO,N2O and NO2 during the second mass loss process.     

Preparation of Ni/TiO2 Nanoparticles and Their Catalytic Performance on the Thermal Decomposition of Ammonium Perchlorate

Metal/oxide nanoparticles are attractive because of their special structure and better properties. The Ni/TiO₂ nanoparticles were prepared by a liquid phase chemical reduction method in this paper. The obtained‐products were characterized by inductively coupled plasma (ICP), X‐ray diffraction (XRD), high‐resolution transmission electron microscopy (HRTEM) and scanning electron microscopy (SEM). The results show that Ni particles in Ni/TiO₂ nanoparticles exhibit better dispersion and the size of most Ni particles is 10 nm or so. The catalytic activity of Ni/TiO₂ nanoparticles on the thermal decomposition of ammonium perchlorate (AP) was investigated by simultaneous thermogravimetry and differential thermal analysis (TG‐DTA). Results show that composite process of Ni and TiO₂ can improve the catalytic activity of Ni nanoparticles on the thermal decomposition of AP, which is mainly attributed to the improvement of Ni dispersion in Ni/TiO₂ nanoparticles. The catalytic activity of Ni/TiO₂ nanoparticles increases with increasing the weight ratio of Ni to AP.     

Facile Fabrication of Cu-doped Carbon Aerogels as Catalysts for the Thermal Decomposition of Ammonium Perchlorate

We report a simple and effective method to produce copper-doped carbon aerogel (Cu-CA) using sodium alginate as a carbon precursor through ion crosslinking and high-temperature carbonization. Results indicate that Cu-alginate has a 3D scaffold structure with pores. The effect of using different metal salt mass ratios of Cu-CA on the catalytic thermal decomposition of AP is also investigated. The thermal decomposition temperature of AP decreases by 94.24 °C, and the activation energy of the decomposition reaction is reduced by 45.7 kJ/mol. These results demonstrate that the composite exhibits superior catalytic performance compared with a single-component transition metal salt.