高择优取向铌酸锶钡薄膜的射频磁控溅射制备

采用溶胶-凝胶法在(100)Si单晶上预先制备出掺钾(K)的铌酸锶钡(SBN)缓冲层，利用射频磁控溅射法在缓冲层KSBN上沉积出高择优取向的铌酸锶钡薄膜，获得了磁控溅射法制备择优取向铌酸锶钡薄膜的相关工艺参数，研究发现，KSBN缓冲层能够很有效地克服衬底与SBN薄膜之间较大的晶格失配，在氧气氩气的比例为1∶2，工作气压为10 Pa，溅射功率300 W，衬底温度300℃，退火温度为800℃的工艺条件下，能够获得c轴高度择优取向的铌酸锶钡铁电薄膜.利用X射线衍射仪，原子力显微镜等仪器分析了薄膜     

高择优取向硅基含钾铌酸锶钡（K:SBN）薄膜的制备与性能

采用NbCl5作为先驱物，利用溶胶-凝胶法在Si(100)衬底上成功获得高度择优取向的铁电铌酸锶钡(SBN)薄膜.与用Nb(OC2H5)5作为先驱物的SBN薄膜相比，NbCl5配制的薄膜前驱溶液中含有一定数量的K离子.K离子的含量对SBN薄膜取向的影响存在一个最优值.二次离子质谱测试发现，K离子对SBN晶胞的溶入和对Si衬底的渗透能够同时使SBN晶胞和Si晶胞产生微小扭曲，从而起到调整薄膜与衬底的匹配关系，并最终促使SBN薄膜c轴高度择优取向的生长.测试了薄膜的光学特性. 关键词： 铌酸锶钡 溶胶-凝胶方法 择优取向     

以MgO为缓冲层的硅基铌酸锶钡薄膜取向特性与其波导结构的设计研究

采用溶胶－凝胶法在Si(100)基片上制备出择优取向的MgO薄膜,随后在其上生长出具有择优取向的铌酸锶钡铁电薄膜.实验发现,MgO缓冲层的应用可以大大提高SBN薄膜的择优取向性能.同时,用五层对称理想波导耦合模理论,以SBN为波导层,分析了波导损耗与厚度的关系. 通过对计算出的理想结果与实际相结合,以及对SBN在生长过程工艺与损耗关系的研究,制备出高质量、低损耗的SBN薄膜,为其在电光波导调制器等微系统中的应用打下良好的基础.     

铌酸锶钡薄膜的微结构与电光性能的研究

本文叙述了使用溶胶凝胶法在MgO(0 0 1)的衬底上制备铌酸锶钡薄膜的过程 ,膜层厚度可达 5 μm。通过X射线衍射、摇摆曲线、扫描、拉曼散射光谱等方法研究了薄膜的微结构性能 ,实验发现 ,铌酸锶钡薄膜具有了较好的 (0 0 1)方向的优先取向性能 ,并且随着薄膜厚度的增加 ,其晶体取向性也会随之不断改进。熔石英的透明衬底上生长的SBN薄膜具有较大的电致双折射效应 ,其有效电光系数能够高达 6 6 2× 10 -11m/V。     

铁电SBN薄膜电光系数的测量及其在波导中的应用

利用溶胶-凝胶法在MgO(001)衬底上获得C轴择优取向的铁电铌酸锶钡(SBN)薄膜,主要介绍MgO(001)衬底上SBN60薄膜及掺入的K离子与Nb离子摩尔比例为1：3的SBN60薄膜横向电光系数r51的测量,实验测得不掺K的SBN60薄膜r51值为37．6pm／V,掺K的r51值为58．5pm／V。并由此设计一种基于MgO(001)衬底上的马赫一曾德尔型SBN60薄膜波导调制器,计算出在633nm时,掺K比例为1：3的此种波导调制器半波调制电压值为10V,不掺K的半波电压值为16V,结果说明掺入K离子能增加薄膜的横向电光系数并有效的减少波导的半波调制电压。     

铁电铌酸锶钡薄膜的结构特性研究

采用溶胶凝胶法在Si(001)基片上制备铁电铌酸锶钡薄膜,使用X射线衍射、摇摆曲线、扫描电子显微镜、喇曼散射光谱等测试手段研究薄膜的微结构与薄膜厚度之间的关系,制备的薄膜厚度可达到5μm.实验发现,随着薄膜厚度的增加,SBN60和SBN75薄膜在(001)方向的优先取向性越来越好.随着膜层的增加,处于底层的膜层能够起到缓冲层的作用,以逐渐改善薄膜与基片之间的晶格失配,从而使得晶体的结晶取向性越来越好.     

薄膜光学 光学薄膜参数测试

O484．5 2005032081 铁电SBN薄膜电光系数的测量及其在波导中的应用= Measurement of electrooptic coefficients in SBN60 thin films and their applications in Mach-Zehnder type waveguide modulators[刊,中]／沈智如(浙江大学现代光学 仪器国家重点实验室．浙江,杭州(310027)),叶辉…∥光 学学报．-2005,25(1)．-121-125 利用溶胶-凝胶法在MgO(001)衬底上获得c轴择优 取向的铁电铌酸锶钡(SBN)薄膜,主要介绍MgO(001)衬     

AlN缓冲层对ZnO薄膜质量的影响

采用脉冲激光沉积法以AlN为缓冲层在Si(100)衬底上制备了ZnO薄膜,并测量了样品的XRD谱、SEM图和PL谱.结果表明,AlN缓冲层可以提高Si衬底上外延生长ZnO薄膜的晶体质量.改变缓冲层的生长温度(50～500 ℃)所制备样品的测量结果表明,较低温度下生长的AlN缓冲层有利于制备高质量的ZnO外延层薄膜,其中AlN缓冲层生长温度为100 ℃时外延生长ZnO薄膜晶体质量最好.     

以Au为缓冲层在Si衬底上生长ZnO薄膜

采用化学气相沉积(CVD)方法在Si(001)衬底上分别制备了有金属Au缓冲层以及无Au缓冲层的ZnO薄膜。其中Au缓冲层在物理气相沉积(PVD)设备中蒸发,厚度大约为300nm。有Au缓冲层的ZnO薄膜晶体质量比直接在Si衬底上生长有了显著提高。利用X射线衍射(XRD)研究了所生长ZnO薄膜的结晶质量,有Au缓冲层的ZnO薄膜虽然仍为多晶,但显示出明显的择优取向。用光学显微镜研究了ZnO薄膜的表面特征,金属Au缓冲层显著地提高了在Si衬底上生长的ZnO薄膜的晶粒尺寸及平整度。同时利用室温光致发光(PL)谱研究了ZnO薄膜的光学性质,并分析了有Au缓冲层的ZnO薄膜NEB发光峰强度反而弱的可能原因。     

退火温度对低温生长MgxZn1-xO薄膜光学性质的影响

用射频磁控溅射法在80℃衬底温度下制备出MgxZn1-xO(x=0.16)薄膜,用X射线衍射(XRD)、光致发光(PL)和透射谱研究了退火温度对MgxZn1-xO薄膜结构和光学性质的影响.测量结果显示,MgxZn1-xO薄膜为单相六角纤锌矿结构,并且具有沿c轴的择优取向;随着退火温度的升高,(002)XRD峰强度、平均晶粒尺寸和紫外PL峰强度增大,(002)XRD峰半高宽(FWHM)减小.结果证明,用射频磁控溅射法通过适当控制退火温度可得到高质量MgxZn1-xO薄膜.     

SBN thin films growth by RF plasma beam assisted pulsed laser deposition

SBN thin films were grown on MgO and Silicon substrates by PLD and RF-PLD (radiofrequency assisted PLD) starting from single crystal Sr_0.6Ba_0.4Nb₂O₆ and ceramic Sr_0.5Ba_0.5Nb₂O₆ stoichiometric targets. Morphological and structural analyses were performed on the SBN layers by AFM and XRD and optical properties were measured by spectroellipsometry. The films composition was determined by Rutherford Backscattering Spectrometry. The best set of experimental conditions for obtaining crystalline, c-axis preferential texture and with dominant 31° in-plane orientation relative to the MgO (100) axis is identified.     

衬底温度对PLD法生长的Mg0.05Zn0.95O薄膜结构和发光特性的影响

用脉冲激光沉积(PLD)法在不同温度的Si(111)衬底上成功制备了c轴择优取向的Mg_005Zn_095O薄膜.通过X射线衍射(XRD)和光致发光谱(PL)研究了衬底温度对Mg_005Zn_095O薄膜结构和发光特性的影响,探讨了薄膜的结晶质量与发光特性之间的关系.结果表明,在衬底温度为450℃时生长的Mg_005Zn_095O薄膜具有很好的c轴取向和较强的光致发光峰.室温下分别用激发波长为240,300和325nm的氙灯作为激发光源得到不同样品的PL谱,分析表明紫外发光峰和紫峰来源于自由激子的复合辐射且发光强度与薄膜的结晶质量密切相关,蓝绿发光峰与氧空位有关.此外,探讨了衬底温度影响紫外光致发光峰红移和蓝移的可能机理. 关键词： 005Zn_095O薄膜')" href="#">Mg_005Zn_095O薄膜 PLD 衬底温度 光致发光     

Thin film properties by facing targets sputtering system

In this study, film thickness distribution and c-axis crystalline orientation of deposited thin films were studied after preparing Co–Cr thin films, a promising ultra-high density perpendicular magnetic recording media, with a facing targets sputtering (FTS) apparatus. Electrical discharge characteristics needed for the optimum operation of sputter device was also studied in order to prepare thin films of superior c-axis crystalline orientation with FTS method (apparatus) in which thin film of fine quality can be formed because temperature increase of substrate due to the bombardment of high-energy particles can be restrained.As a result of the study, it is confirmed that the FTS method can give stable working under broad magnetic field and range of gas pressure and stable electrical discharge under low Ar gas pressure. Film thickness of prepared thin film shows fairy regular distribution and could obtain good thin films whose dispersion angle of c-axis crystalline orientation is about 3.5°.     

蓝宝石基片的处理方法对ZnO薄膜生长行为的影响

采用反应射频磁控溅射方法,在经过不同方法处理的蓝宝石基片上,在同一条件下沉积了ZnO薄膜.利用原子力显微镜、X射线衍射、反射式高能电子衍射等分析技术,对基片和薄膜的结构、表面形貌进行了系统表征.研究结果显示,不同退火条件下的蓝宝石基片表面结构之间没有本质的差异,均为α-Al₂O₃ (001)晶面,但基片表面形貌的变化较大.在不同方法处理的蓝宝石基片上生长的ZnO薄膜均具有高c轴取向的织构特征,但薄膜的表面形貌差异较大.基片经真空退火处 关键词： ZnO薄膜 反应磁控溅射 基片处理 形貌分析     

Structural, defect and optical properties of ZnO films grown under various O2/Ar gas ratios

Thin wurtzite (0 0 2) textured ZnO thin films were deposited on glass substrates by radio frequency magnetron sputtering under O₂/Ar ratios R varying from 0.05 to 1.0 at room temperature. The structure of, and defects in, the films were investigated by XRD, SEM and slow positron beam techniques. The XRD spectra showed that ZnO thin films were polycrystalline with hexagonal structure and a good c-axis orientation perpendicular to the substrate. The thickness, grain size and the crystalline quality of the films strongly depended on R; the larger grain size and thicker ZnO films were grown when R was lower. Positron beam Doppler broadening measurements showed that in low R films additional vacancy-type defects (e.g. Zn-related vacancy complexes or clusters) were formed. Photoluminescence spectra found that the film with R = 0.4 had the highest luminescence efficiency, in good agreement with the best c-axis preferential orientation. The transmittance spectra of the films decreased with decreasing R, due to the thickness effect. Correlations between microstructure, defect and optical properties are discussed.     

择优取向MgO缓冲层上制备的硅基Ba0.7Sr0.3TiO3薄膜的结构和性能研究

分别采用sol-gel法和磁控溅射法在Si（001）单晶衬底上制备出（111）和（001）取向的MgO缓冲层薄膜,随后在其上生长Ba_0.7Sr_0.3TiO₃（BST30）铁电薄膜.通过X射线衍射,扫描电子显微镜,原子力显微镜等方法研究了薄膜的微结构.实验结果发现,在较厚的MgO（001）缓冲层上可长出（101）取向的BST30薄膜,而在较薄的MgO（111） 缓冲层上则表现出（101）和（111）取向相互竞争的现象,随着MgO（111）缓冲 关键词： 0.7Sr_0.3TiO₃')" href="#">Ba_0.7Sr_0.3TiO₃ 铁电薄膜 择优取向 sol-gel     

Ferroelectric SrxBa1-xNb2O6 optical waveguiding thin films on SiO2-coated Si(100) substrates

x Ba_1-xNb₂O₆ (x=0.5) films (abbreviated as SBN:0.5) on SiO₂-coated Si substrates are potential components for the application of integrated electro-optics devices. SBN:0.5 optical waveguiding thin films on SiO₂-coated Si substrates with a very thin MgO diffusion buffer have been successfully prepared by pulsed laser deposition. The as-grown films have a refractive index of 2.28, which is close to that of bulk SBN. X-ray analysis showed that the as-grown films have a single-phase tetragonal tungsten bronze structure. The SBN:0.5 thin films prepared by PLD exhibit favorable ferroelectric and optical waveguiding properties. The composition and the morphology of the films were also examined by XPS and by SEM, respectively. Ferroelectric SBN:0.5 optical waveguiding thin films on SiO₂-coated Si substrates are expected to be used in integrated electro-optic devices. Received: 27 February 1997/Accepted: 17 October 1997     

Influence of substrate crystallography on the room temperature synthesis of AlN thin films by reactive sputtering

A pulsed DC reactive ion beam sputtering system has been used to synthesize aluminium nitride (AlN) thin films at room temperature by reactive sputtering. After systematic study of the processing variables, high-quality polycrystalline films with preferred c-axis orientation have been grown successfully on silicon and Au/Si substrates with an Al target under a N₂/(N₂ + Ar) gas flow ratio of 55%, 2 mTorr processing pressure and keeping the temperature of the substrate holder at room temperature. The crystalline quality of the AlN layer as well as the influence of the substrate crystallography on the AlN orientation has been characterized by high-resolution X-ray diffraction (HR-XRD). Best ω-FWHM (Full Width at Half Maximum) values of the (0 0 0 2) reflection rocking curve in the 1 μm thick AlN layers are 1.3°. Atomic Force Microscopy (AFM) measurements have been used to study the surface morphology of the AlN layer and Transmission Electron Microscopy (TEM) measurements to investigate the AlN/substrate interaction. AlN grew off-axis from the Si substrate but on-axis to the surface normal. When the AlN thin film is deposited on top of an Au layer, it grows along the [0 0 0 1] direction but showing a two-domain structure with two in-plane orientations rotated 30° between them.     

涂层导体用金属基带表面对过渡层成核的机理研究

涂层导体用金属基带的表面状况对在其上制备的过渡层的形貌和取向有很大影响.在Ni单晶、轧制辅助双轴织构基带(RABiTS)Ni和经过硫化处理的Ni基带三种不同衬底上采用磁控溅射法制备了CeO₂过渡层.结果表明,在Ni单晶和硫化处理的Ni基带上制备的CeO₂薄膜取向较差,而在RABiTS Ni上制备的CeO₂薄膜完全呈c轴取向,表面平整致密.反射高能电子衍射图显示,RABiTS Ni具有的c(2×2)的S超结构对CeO₂薄膜的取向生长起到了很重要的作用. 关键词： 涂层导体 金属基带 超结构 过渡层