Kinetics and rate-limiting mechanisms of dolomite dissolution at various CO_2 partial pressures

Techniques of rotating-disk and catalyst were used in investigating the kinetics of dolomite dissolution in flowing CO2-H2O system. Experiments run in the solutions equilibrated with various CO2 partial pressures (PCO2) from 30 to 100000 Pa. It shows that dissolution rates of dolomite are related with rotating speeds at conditions far from equilibrium. This was explained by modified diffusion boundary layer (DBL) model. In addition, the dissolution rates increase after addition of carbonic anhydrase (CA) to solutions, where the CA catalyzes CO2 conversion. However, great differences occur among various CO2 partial pressures. The experimental observations give a conclusion that the modified DBL model enables one to predict dissolution rates and their behaviour at various PCO2 with satisfactory precision at least far from equilibrium.     

Kinetics and rate-limiting mechanisms of dolomite dissolution at various CO2 partial pressures

Techniques of rotating-disk and catalyst were used in investigating the kinetics of dolomite dissolution in flowing CO₂-H₂O system. Experiments run in the solutions equilibrated with various CO₂ partial pressures (P_{CO 2} ) from 30 to 100000 Pa. It shows that dissolution rates of dolomite are related with rotating speeds at conditions far from equilibrium. This was explained by modified diffusion boundary layer (DBL) model. In addition, the dissolution rates increase after addition of carbonic anhydrase (CA) to solutions, where the CA catalyzes CO₂ conversion. However, great differences occur among various CO₂ partial pressures. The experimental observations give a conclusion that the modified DBL model enables one to predict dissolution rates and their behaviour at various P_{CO 2} with satisfactory precision at least far from equilibrium.     

片状纳米结构CeO2晶体的制备及其吸附CO2性能

在室温下,将CeCl₃溶液与CO₂储存材料（CO₂SM）混合、搅拌0.5 h制备了片状碳酸铈前驱体（CCPs）,并在500℃下煅烧CCPs 4 h,制得平均尺寸为4.94 μm×0.92 μm,厚度为0.04~0.08 μm纳米结构片状CeO₂晶体。在此过程中,CO₂SM不但可以提供CO₃^2-,还能起到分散剂和结构导向剂的作用。反应过程中,系统地研究了CO₂SM用量、Ce³⁺浓度和搅拌时间3个因素对CCPs形态和大小的影响,得到最优制备条件：0.1 g CO₂SM和50 mL 0.03 mol·L^-1 Ce³⁺水溶液以1 000 r·min^-1转速在室温下搅拌0.5 h。煅烧CCPs后,所制备的片状CeO₂晶体在室温下CO₂吸附量可达0.554 mmol·g^-1。     

TiO_2纳米带光催化二氧化碳甲烷化

研究了在常温常压下TiO2纳米带光催化CO2催化加氢气反应。在紫外光照射下,二氧化碳的加氢还原产物为甲烷。利用高分辨TEM,XRD,UV-Vis DRS,低温氮吸附-脱附,TG等考察了催化剂与甲烷产率的构效关系。结果表明,在600℃焙烧时得到的双晶材料具有最佳的光催化活性。优异的光催化活性主要得益于TiO2双晶脱水纳米带(DNR Bicrystalline dehydratednanoribbon)。上面形成的纳米晶界能够提高催化剂在紫外区的光吸收能力,TiO2(B)和锐钛矿独特的双晶间隔结构也提高了界面电荷分离的效率。担载贵金属Pt显著地提高了反应速率。     

一个Yb8簇合物的合成、结构及CO2催化转化性质

使用多齿席夫碱配体H₂L与Yb(acac)₃·2H₂O反应,设计并通过溶剂热法合成了一例结构新颖的八核镱簇合物[Yb₈(acac)₄(HL)₄(L)₂(μ₃-O)₄(C₂H₅O)₄]·2C₂H₅OH·2CH₂Cl₂ (1)。单晶 X 射线衍射分析表明,簇合物呈中心对称的八核结构,中心稀土离子Yb1(Ⅲ))为八配位的双帽三角棱柱几何构型,Yb2、Yb3和Yb4均为七配位,分别为单帽三角棱柱、五角双锥及单帽八面体几何构型。簇合物1具有良好的溶剂稳定性。近红外荧光测试表明：簇合物1在室温下表现出Yb(Ⅲ)特征发射峰。此外,催化性质研究表明：簇合物1可以有效地催化CO₂与环氧化合物的环加成反应,且作为异相催化剂表现出良好的循环性能。     

一个Yb8簇合物的合成、结构及CO2催化转化性质

使用多齿席夫碱配体H₂L与Yb(acac)₃·2H₂O反应,设计并通过溶剂热法合成了一例结构新颖的八核镱簇合物[Yb₈(acac)₄(HL)₄(L)₂(μ₃-O)₄(C₂H₅O)₄]·2C₂H₅OH·2CH₂Cl₂(1)。单晶X射线衍射分析表明,簇合物呈中心对称的八核结构,中心稀土离子Yb1(Ⅲ)为八配位的双帽三角棱柱几何构型,Yb2、Yb3和Yb4均为七配位,分别为单帽三角棱柱、五角双锥及单帽八面体几何构型。簇合物1具有良好的溶剂稳定性。近红外荧光测试表明：簇合物1在室温下表现出Yb(Ⅲ)特征发射峰。此外,催化性质研究表明：簇合物1可以有效地催化CO₂与环氧化合物的环加成反应,且作为异相催化剂表现出良好的循环性能。     

Solid products and rate-limiting step in the thermal half decomposition of natural dolomite in a CO2 (g) atmosphere

Natural dolomite powders obtained from caves which give unusual high resistance building materials, have been decomposed in a Knudsen cell at high CO₂ pressures in the temperature range of 913-973 K. XRD traces for the final solid products, after the first half thermal decomposition, have shown, that beside the XRD patterns for the calcite and MgO, the existence of a new structure with major peaks at 2θ equal to 38.5 and 65°. This finding has been ascribed to a solid solution of MgO in calcite. The kinetic analysis of the TG curves yield a total apparent enthalpy (ΔH^∗) for the decomposition equal to 440±10 kJ mol⁻¹ for a range of fraction decomposed (α) varying between 0.2 and 0.7. This value is much closer to the theoretical expected at 950 K value ΔH=486 kJ mol⁻¹ for the dolomite decomposition in CO₂ environment, where CaO, MgO and oxides of solid solution can be the solid reaction products. The rate determining step is the transport of CO₂ across the reacting interface through an high activated thermal process due to solid state diffusion of CO₃²⁻ in the bulk and/or the grain boundaries phases of CaCO₃ and/or of the solid solution. The microstructure evolution of the solid products follows a shear-transformation mechanism. At temperatures below 943 K, porous product particles are characterized by a monomodal narrow pore size distribution around 0.05 μm. At higher temperatures, a critical level of tensions inside the particles is reached and a bimodal pore size distribution around 1 and 0.05 μm is formed.     

R&D activities in Japan on methanol synthesis from CO2 and H2

Methanol synthesis from CO₂ and H₂ can be a useful process for conversion and transportation of hydrogen energy derived from non-fossil energies. More than ten research groups in Japan have extensively investigated the methanol synthesis from both academic and practical points of view. Recent R&D activities in Japan for developing high performance catalysts, for elucidating the reaction mechanism and also for operating a bench scale plant have been reviewed in this paper.     

制备工艺对NiFe2O4分解CO2活性的影响

随着大气中CO2浓度的增加,温室效应日趋严重,促使人们对大气中CO2的转化与消除这一课题更加重视。1990年Yutaka Tamaura[1]发现氧缺位磁铁矿几乎可以100%分解CO2后,为解决温室效应提供了一条新的探索途径。通过对不同铁酸盐MFe2O4(M=Fe,Mn[2],Co[3],Zn[4],Ni[5]等)分解CO2活性的考察,发现铁酸镍在300℃分解CO2的活性比其它铁酸盐都好。NiFe2O4的制备最常采用的是共沉淀法、柠檬酸溶胶凝胶法和水热法,3种方法由于制备     

CO2 anion-radical in organic carboxylations

This letter shows a first approximation to the use of CO₂ anion-radical in the obtention of α-methyl and α-ethylcyanoacetic acids from propionitrile and butyronitrile, respectively, through a paired electrochemical reaction with CO₂. The electrosynthesis of α-chloro-phenylacetic acid from benzyl chloride and phenylacetic acid from toluene by another proposed pathway is also discussed.     

ZIF-67/CeO2催化CO2和甲醇直接合成碳酸二甲酯

采用沉淀法将ZIF-67负载到CeO₂上,制备了具有多重活性位点的非均相催化剂ZIF-67/CeO₂,并研究其催化CO₂和甲醇直接反应生成碳酸二甲酯(DMC)的性能。采用 X 射线衍射、N2吸附-脱附、傅里叶变换红外光谱和 X 射线光电子能谱研究了ZIF-67/CeO₂的各种理化性质。结果表明,ZIF-67的引入使ZIF-67/CeO₂催化剂产生更多的氧空位。在考察的ZIF-67/CeO₂系列催化剂中,0.3-ZIF-67/CeO₂(0.3为Co、Ce物质的量之比)在具有高的比表面积的同时还能保持介孔结构,具有丰富的酸碱位点,并且具有较高的CO₂吸附容量,表现出最好的催化性能。在反应温度为140℃、压力为4.5 MPa的条件下反应4 h,DMC收率可达到3.79 mmol_DMC·gcat^-1。     

La2(CO3)3纳米线的微乳液法制备与表征

La₂(CO₃)₃ nanowires were prepared in the nonionic surfactant microemulsion(Triton X-100/cyclohexane/water)system. Transmission electron microscopy (TEM) and selected area electronic diffraction (SAED) were used to characterize the shape and size of the products. The results showed that the pH value and concentration of mother solution, temperature and aging time all could affect the morphology and size of the La₂(CO₃)₃ nanowires. The lengths of the nanowires were more than 10 μm and the diameters were in the range of 30～200 nm.     

ZIF-67/CeO2催化CO2和甲醇直接合成碳酸二甲酯

采用沉淀法将ZIF-67负载到CeO₂上,制备了具有多重活性位点的非均相催化剂ZIF-67/CeO₂,并研究其催化CO₂和甲醇直接反应生成碳酸二甲酯(DMC)的性能。采用X射线衍射、N₂吸附-脱附、傅里叶变换红外光谱和X射线光电子能谱研究了ZIF-67/CeO₂的各种理化性质。结果表明,ZIF-67的引入使ZIF-67/CeO₂催化剂产生更多的氧空位。在考察的ZIF-67/CeO₂系列催化剂中,0.3-ZIF-67/CeO₂(0.3为Co、Ce物质的量之比)在具有高的比表面积的同时还能保持介孔结构,具有丰富的酸碱位点,并且具有较高的CO₂吸附容量,表现出最好的催化性能。在反应温度为140℃、压力为4.5 MPa的条件下反应4 h,DMC收率可达到3.79 mmol_DMC·g_cat^-1。     

CrOx/SiO2催化剂上丙烷在CO2气氛中脱氢反应的研究

采用XRD、UV-vis DRS、ESR和微分吸附量热等技术,考察了铬担载量分别为2.5、5和10wt%的CrO_x/SiO₂催化剂的结构、表面性质和氧化还原性能。结果表明,催化剂表面上存在多种Cr的氧化态和聚集形式。随着Cr担载量从2.5wt%到10wt%的逐渐增大,催化剂表面占主导地位的Cr物种由CrO₃单体转为多聚CrO₃和Cr₂O₃晶相。在CO₂气氛中催化剂对丙烷转化率和丙烯选择性的大小顺序为2.5wt%CrO_x/SiO₂>5wt%CrO_x/SiO₂>10wt%CrO_x/SiO₂,反应过程中的原位ESR和UV-visDRS测定结果表明,催化剂表面的反应活性中心为Cr⁵⁺,Cr⁵⁺可由催化剂预处理过程中Cr³⁺的氧化及丙烷反应过程中CrO₃单体的还原产生,在反应中CO₂可使Cr³⁺重新氧化为Cr⁵⁺.     

含O2高温高压CO2环境中3Cr钢腐蚀产物膜特征

采用高温高压反应釜分别开展3Cr钢在CO2和O2共存、单独CO2和单独O2三种气体条件下的腐蚀实验,利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、能量色散X射线能谱(EDS)和电化学方法研究了3Cr钢在高温高压含有O2的CO2环境中的腐蚀产物膜特征.结果表明,在含有O2的CO2的条件下,3Cr钢表面腐蚀产物膜疏松多孔,主要成分为FeCO3、Fe3O4和Fe2O3,腐蚀产物中未见明显Cr元素富集,3Cr钢表现出点蚀的腐蚀形态.3Cr钢在高温高压含O2的CO2腐蚀条件下内外膜层电阻(Rf1、Rf2)和电荷传递电阻Rt均比仅含有CO2腐蚀环境的低,双电层电容(Cdl)和内外膜层电容(Cf1、Cf2)均比仅含有CO2腐蚀环境的高.含有O2的CO2条件下,其保护性显著低于单一CO2条件下形成的腐蚀产物膜.提出了在含O2的CO2气体条件下,3Cr钢表面存在由多种物质组成的腐蚀产物,这导致腐蚀产物疏松多孔,不会形成单一CO2条件下存在的显著提高腐蚀产物膜保护性的Cr(OH)3层,从而促进了3Cr钢的析氢腐蚀和酸性介质中的吸氧腐蚀的机理.     

Structural change of layered perovskite La2Ti2O7 at high pressures

The perovskite-related layered structure of La₂Ti₂O₇ has been studied at pressures up to 30 GPa using synchrotron radiation powder X-ray diffraction (XRD) and Raman scattering. The XRD results indicate a pronounced anisotropy for the compressibility of the monoclinic unit cell. The ratio of the relative compressibilities along the [100], [010] and [001] directions is ∼1:3:5. The greatest compressibility is along the [001] direction, perpendicular to the interlayer. A pressure-induced phase transition occurs at 16.7 GPa. Both Raman and XRD measurements reveal that the pressure-induced phase transition is reversible. The high-pressure phase has a close structural relation to the low-pressure monoclinic phase and the phase transition may be due to the tilting of TiO₆ octahedra at high pressures.     

Li2ZrO3材料吸收CO2性能的进一步研究

用不同结构的ZrO₂合成了一系列在高温下吸收CO₂的Li₂ZrO₃材料，并详细的研究了反应物质的物理和化学性质对生成物吸收CO₂性能的影响。采用SEM、XRD以及TG分析法分别进行了材料结构及其吸收CO₂性能的表征，并使用XPS法测定了材料表面的元素组成。实验结果表明，使用不同结构的ZrO₂合成的Li₂ZrO₃，其吸收CO₂的性能明显的不同。用ZrO₂(t)(四方)合成的Li₂ZrO₃吸收CO₂的速度快，在500 ℃下，20% CO₂（80%空气）的气氛中保持3h，其吸收量可达25（±0.6）%（wt），而以ZrO₂(m)(单斜)为原料制备的Li₂ZrO₃在上述吸收条件下重量仅增加9（±0.6）%（wt）。此外，实验结果还表明化学元素的掺杂对用ZrO₂(m)合成的Li₂ZrO₃的CO₂吸收速度及吸收容量影响较大。     

S型异质结光催化剂ZnFe2O4/WO3的构筑及光催化还原CO2性能

通过在WO₃纳米片表面负载ZnFe₂O₄纳米颗粒,构建了一系列S型异质结光催化剂ZnFe₂O₄/WO₃,并研究了其光催化CO₂还原性能。在没有助催化剂和牺牲剂的条件下,所制备的ZnFe₂O₄/WO₃复合材料可对CO₂与水蒸汽进行光催化反应。优化后的材料光照5 h后CO₂还原产物CO和CH₄的产量分别为7.87和4.88 μmol·g^-1。相对于单相组分,CO和CH₄的产量明显提高。光催化活性的提高,归因于ZnFe₂O₄和WO₃异质结的形成以及光生载流子的S型电荷传输模式。     

S型异质结光催化剂ZnFe2O4/WO3的构筑及光催化还原CO2性能

通过在WO₃纳米片表面负载ZnFe₂O₄纳米颗粒,构建了一系列S型异质结光催化剂ZnFe₂O₄/WO₃,并研究了其光催化CO₂还原性能。在没有助催化剂和牺牲剂的条件下,所制备的ZnFe₂O₄/WO₃复合材料可对CO₂与水蒸汽进行光催化反应。优化后的材料光照5 h后CO₂还原产物CO和CH₄的产量分别为7.87和4.88 μmol·g^-1。相对于单相组分,CO和CH₄的产量明显提高。光催化活性的提高,归因于ZnFe₂O₄和WO₃异质结的形成以及光生载流子的S型电荷传输模式。     

Z型Ag-Cu2O/BiVO4光催化剂的光催化还原CO2性能

利用简单的化学还原沉积法将 Cu₂O纳米球和 Ag纳米颗粒均匀包裹在十面体 BiVO₄表面,成功构建了一种具有高效电荷载流子分离/转移特性的Z型异质结光催化剂Ag-Cu₂O/BiVO₄。Ag-Cu₂O/BiVO₄在可见光下光催化CO₂还原为CO的产率可达5.37 μmol·g^-1·h^-1,分别是纯 BiVO₄和 Cu₂O的 35.80倍和 6.30倍。通过 X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、X射线能谱(EDS)、紫外可见漫反射光谱(UV-Vis DRS)、光致发光(PL)光谱、瞬态光电流响应(TPC)和电化学阻抗谱(EIS)对 Ag-Cu₂O/BiVO₄的晶体结构、形貌、组成、能带结构和吸光能力等进行了系统表征分析,并提出了其光催化体系还原CO₂的催化机理。