Characterization of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles synthesized by various methods

Microwave-induced combustion with glycine, CTAB-assisted hydrothermal process with NaOH and NH3, EDTA assisted-hydrothermal methods have been applied to prepare NiFe₂O₄ nanoparticles for the first time. Structural and magnetic properties of the products were investigated by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmison electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), and electron spin resonance spectrometry (EPR). TEM measurements showed that morphology of the product depends on the synthesis method employed. The average cystallite size of NiFe₂O₄ nanoparticles was in the range of 14–59 nm as measured by XRD. The uncoated sample (Method A) had an EPR linewidth of 1973 Oe, the coated samples reached lower values. The magnetic dipolar interactions existing among the Ni ferrite nanoparticles are reduced by the coatings, which could cause the decrease in the linewidth of the EPR signals. Additionally, the linewidth increases with an increase in the size and the size distribution of nanoparticles.     

Optimal design and characterization of superparamagnetic iron oxide nanoparticles coated with polyvinyl alcohol for targeted delivery and imaging

Superparamagnetic iron oxide nanoparticles (SPION) with narrow size distribution and stabilized by polyvinyl alcohol (PVA) were synthesized. The particles were prepared by a coprecipitation technique using ferric and ferrous salts with a molar Fe3+/Fe2+ ratio of 2. Using a design of experiments (DOE) approach, the effect of different synthesis parameters (stirring rate and base molarity) on the structure, morphology, saturation magnetization, purity, size, and size distribution of the synthesized magnetite nanoparticles was studied by various analysis techniques including X-ray powder diffraction (XRD), thermogravimetric analysis (TGA) with differential scanning calorimetry (DSC) measurements, vibrating-sample magnetometer (VSM), transmission electron microscopy (TEM), UV-visible, and Fourier transform infrared (FT-IR) spectrometer. PVA not only stabilized the colloid but also played a role in preventing further growth of SPION followed by the formation of large agglomerates by chemisorption on the surface of particles. A rich behavior in particle size, particle formation, and super paramagnetic properties is observed as a function of molarity and stirring conditions. The particle size and the magnetic properties as well as particle shape and aggregation (individual nanoparticles, magnetic beads, and magnetite colloidal nanocrystal clusters (CNCs) are found to be influenced by changes in the stirring rate and the base molarity. The formation of magnetic beads results in a decrease in the saturation magnetization, while CNCs lead to an increase in saturation magnetization. On the basis of the DOE methodology and the resulting 3-D response surfaces for particle size and magnetic properties, it is shown that optimum regions for stirring rate and molarity can be obtained to achieve coated SPION with desirable size, purity, magnetization, and shape.     

Preparation and Magnetic Property of La_(0.7)Sr_(0.3)MnO_3 Nanorod by Combination Sol-Gel with Molten Salt

La0.7Sr0.3MnO3(LSMO) nanorods were synthesized by a method combining sol-gel with molten salts at 950 °C for 10 h, which employed KCl+NaCl(mass ratio 4:1) as eutectic molten salts. The morphologies and magnetic properties of the resulting LSMO nanorods were investigated by X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), and vibrating sample magnetometer(VSM) measurements. It was found that the obtained perovskite manganite LSMO was a uniform nanorod with a d...     

Synthesis of Fe3O4@SiO2-Ag magnetic nanocomposite based on small-sized and highly dispersed silver nanoparticles for catalytic reduction of 4-nitrophenol

We demonstrate a single-step facile approach for the synthesis of glycine (amino acid) passivated Fe(3)O(4) magnetic nanoparticles (GMNPs) using soft chemical route. The surface passivation of Fe(3)O(4) nanoparticles with glycine molecules was evident from infrared spectroscopy, thermal and elemental analyses, and light scattering measurements. These nanoparticles show better colloidal stability, good magnetization, excellent self-heating capacity under external AC magnetic field and cytocompatibility with cell lines. Further, the active functional groups (-NH(2)) present on the surface of Fe(3)O(4) nanoparticles can be accessible for routine conjugation of biomolecules/biolabelling through well-developed bioconjugation chemistry. Specifically, a new colloidal glycine passivated biocompatible Fe(3)O(4) nanoparticles with excellent specific absorption rate (SAR) have been fabricated, which can be used as an effective heating source for hyperthermia treatment of cancer (thermal therapy).     

Magnetic applications of polymer gels

In this paper we report results of both, material preparation and magnetic characterisation, on CoFe₂O₄ particles of nanometric size formed by in‐situ precipitation within polymer gels. The size of the particles was controlled within a very narrow volume distribution and its average value was shifted from 2 to 10 nm. The existence of nanoparticles showing, at room temperature, coercive field values between 500 and 900 Oe and saturation magnetisations of about 500 emu/cm³, suggest to use these systems to get magnetic recording media with ultra high density. Poly(vinyl alcohol) (PVA) and Polystyrene (PS) films were prepared from this nanocomposite material. After a magnetic field treatment nanoparticles within the PVA films are free to rotate in response to an applied magnetic field. This PVA based nanocomposite film portends a new class of magnetic material with very little or no electrical and magnetic loss.     

Solvothermal synthesis of NiCo alloy icosahedral nanocrystals

New dimensional NiCo alloy icosahedral nanocrystals with controllable size have been first reported and synthesized through an Ostwald ripening process in a template-absent solvothermal reaction system. The proposed synthesis is corroborated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction analysis (XRD), energy-dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS). The as-obtained NiCo icosahedral nanocrystals exhibit the size- and component-dependent magnetic behaviors. The coercivity (H(c)) depends on both the magnetocrystalline and structure anisotropy, and the saturation magnetizations (M(s)) decided by the content of Co. H(c) decreases from 189.02 to 147.95 Oe with the increase of the icosahedral NCs size from 200 to 850 nm. Especially, the H(c) of the icosahedral NCs at 157.38 Oe is higher than that of nanospheres at 104.02 Oe. In addition, M(s) and H(c) increased with the increasing Co content. It can be an ideal building block for applications in magnetic media, sensors, and other devices.     

Preparation,surface morphology,and optical properties of indium(III) oxide nanoparticles by thermolysis of indium–poly(vinyl alcohol) coordination polymer

First report on the preparation of well-dispersed, indium(III) oxide (In₂O₃) nanoparticles with 22–35?nm size by polymer thermolysis is presented. Indium–poly(vinyl alcohol) (PVA) coordination polymer films were prepared by ‘solution casting technique’ from the homogeneous aqueous solution of coordination polymer prepared using PVA and indium(III) nitrate as starting materials; subsequently the films were calcined at 550?°C to yield In₂O₃ nanoparticles. Both indium–PVA coordination polymer that served as the precursor and the titled nanoparticles were characterized by Fourier transform-infrared spectroscopy, photoluminescence (PL), powder X-ray diffraction (XRD), transmission electron microscopy, and thermal analysis. Room temperature PL spectra of the prepared indium oxide nanoparticles showed intense blue emissions around 360, 410 and 430?nm, characteristic of indium oxide nanoparticles due to oxygen vacancies. The lower energy PL emission decreases with an increase of indium(III) content in the precursor. The size of the nanoparticles calculated from line broadening of XRD pattern (cubic; JCPDS: 06-0416) was found to be around 24?nm. The average particle size of the synthesized nanoparticles increased with metal ion content in the precursor coordination polymer.     

Size and surface effects on the magnetic properties of NiO nanoparticles

NiO nanoparticles (NPs) were prepared by a sol-gel process using the citrate route. The sol-gel parameters were tuned to obtain samples with different average particle sizes, ranging from 12 to 70 nm. Magnetic characterization revealed an increase in the blocking temperature with the diameter of the NPs and an increase in the effective magnetic anisotropy (K(eff)) with decreasing particle size. The magnetic moment per particle was calculated for all samples using the susceptibility value at T = 300 K. The number of uncompensated spins per NP was found to be proportional to n (n(S)≡ total number of spins), indicating that they are randomly distributed on the NP surface. For small diameters (<30 nm) the surface anisotropy constant was estimated, using, for NiO NPs, a recent model describing the evolution of K(eff) with particle size. Hysteretic loops performed at low temperatures after field cooling displayed loop shifts (～6.5 kOe in the field axis and ～0.18 emu g(-1) vertically), coercive field enhancement (H(C)≈ 4.8 kOe) and training effects for the smaller NPs. The sample with NPs of larger diameters presented magnetic properties close to those of bulk NiO.     

Influences of surfactant (PVA) concentration and pH on the preparation of copper nanoparticles by electron beam irradiation

Electron beam irradiation method was successfully applied to the preparation of Cu nanoparticles in aqueous solution under room temperature and ambient pressure using polyvinyl alcohol (PVA) as the surfactant. The influences of the pH on the products were studied by X-ray diffraction (XRD), and those of the surfactant PVA concentration on the particle size and agglomeration by ultraviolet–visible spectrophotometry (UV–vis) and laser scattering particle size distribution analysis (LSPSDA). The products were characterized by XRD and transmission electron microscopy (TEM). The results showed that the grain size of Cu nanoparticles, within a certain range, can decrease with increasing PVA concentration. Pure Cu nanoparticles with the grain size distribution of 5–50 nm were prepared when the pH was adjusted between 5.0 and 9.0, and the PVA concentration was 2.20 g/100 mL.     

Pentenoic Acid-Stabilized Magnetic Nanoparticles for Nanomedicine Applications

One-pot magnetic nanoparticles capped with pentenoic acid were prepared by co-precipitation process of Fe²⁺ and Fe³⁺ in the presence of ammonium hydroxide solution. The morphology and the hydrodynamic diameter of the prepared nanoparticles were characterized using scanning electron microscopy and dynamic light scattering, while stability, surface charge, and magnetic properties were assessed through thermogravimetric analysis, zeta potential, and a vibrating sample magnetometer, respectively. The type of interaction between iron nanoparticles and the carboxylate head of pentenoic acid was studied using Fourier transform infrared (FTIR). It indicates the existence of a bidentate chelation and pentenoic acid is not only adsorbed on the iron nanoparticles, but to some extent the nanoparticles are chemically bonded. When an alternating magnetic field is applied, magnetic materials are observed to heat as a result of relaxation. The heat generated from samples was examined by exposing a suspension containing 20% and 30% nanoparticles for an alternating current (AC) magnetic field. Our results demonstrate that the simplification of the synthetic methodology for magnetic nanoparticles with a high specific absorption rate (SAR) shows potential for hyperthermia application.     

Preparation and Magnetic Property of La0.7Sr0.3MnO3 Nanorod by Combination Sol-Gel with Molten Salt

La0.7Sr0.3MnO3（LSMO） nanorods were synthesized by a method combining sol-gel with molten salts at 950 ℃ for 10 h, which employed KCl＋NaCl（mass ratio 4：1） as eutectic molten salts. The morphologies and magnetic properties of the resulting LSMO nanorods were investigated by X-ray diffraction（XRD）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, and vibrating sample magnetometer（VSM） measurements. It was found that the obtained perovskite manganite LSMO was a uniform nanorod with a diameter of about 50 nm and a length of longer than 500 rim. The Curie temperature（To） of the LSMO nanorod used here was 262 K, much lower than that of bulky single crystal LSMO（360 K）. The low Curie temperature might be a result of the great disorder near the grain boundary, which could be observed clearly from the TEM picture.     

A simple route to synthesize nanocrystalline nickel ferrite (NiFe2O4) in the presence of octanoic acid as a surfactant

Nanocrystalline nickel ferrite (NiFe₂O₄) powder was prepared by a co-precipitation method from Ni and Fe chlorides. The as-prepared samples were characterized by powder X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry (VSM). SEM and TEM indicated that the particles were spherical with particle sizes in the range 25 ± 5 nm. The magnetic properties of the sample were measured by using a vibrating sample magnetometer, which showed that the sample exhibited typical ferromagnetic behavior at room temperature, while a finite coercivity of 245.5 Oe was present at 300 K. The saturation magnetization of the sample (23.13 emu/g) was significantly lower than that for the reported multidomain bulk particles (55 emu/g), reflecting the ultrafine nature of the sample.     

Synthesis and stabilization of Prussian blue nanoparticles and application for sensors

Prussian blue (PB) nanoparticles were synthesized by two methods from FeCl2 and K3Fe(CN)6 and from FeCl3 and K3Fe(CN)6 based on the method published by Fiorito et al., and stabilized by different polymers like polyvinyl alcohol (PVA), polyvinyl pyrrolidone (PVP), polyallylamine hydrochloride (PAH), polydiallyl-dimethyldiammonium chloride (PDDA) and polystyrene sulfonate (PSS). The effect of the monomer/Fe3+ ratio was studied regarding the average particle size and zeta-potential. The forming PB structure was checked by X-ray diffraction. The stabilization was successful for every applied polymer, but the average particle size significantly differs. Particle size distributions were determined by Malvern type nanosizer equipment and by transmission electron microscope (TEM) and zeta potential values were determined for the obtained stabile samples. The results revealed that by using FeCl2 and K3Fe(CN)6 for PB preparation particles with narrow size distribution and average diameter of 1.7 nm occurred but stabilization was necessary. By the other method the dispersion was stabile with 182 nm particles but the particle size exponentially decreased to 18 nm with increasing PVP concentration. Ultrathin nanofilms were prepared on glass support by the alternating layer-by-layer (LbL) method from PB particles and PAH. The morphology of the prepared films was investigated also by AFM. The films were immobilized on interdigitated microsensor electrodes (IME) and tested in sensing hydrogen peroxide and different acids like acetic acid, hydrochloric acid vapors.     

Large Magnetocaloric Effect,Moment, and Coercivity Enhancement after Coating Ni Nanoparticles with Ag

We observe a large magnetocaloric effect in monodisperse Ni and Ni_coreAg_shell nanoparticles in the superparamagnetic region. The organically passivated Ni nanospheres show a large magnetic entropy change of 0.9 J kg^?1 K for a 3 T magnetic field change. In comparison to the surfactant‐coated Ni nanoparticles, the Ni_coreAg_shell nanoparticles show an enhanced coercivity, magnetization, and magnetocaloric effect (1.3 kg K for a 3 T magnetic field change). The coercivity at 10 K increases from 360 Oe for Ni nanoparticles to nearly 610 Oe for Ni_coreAg_shell particles. This large enhancement is attributed to the enhanced inter‐particle interaction, which is mediated by the metallic shell, over the relatively weaker dipolar interaction in the surfactant‐coated Ni nanoparticles, and to modification of the surface spin structure.     

Fe3O4-LiMo3Se3 nanoparticle clusters as superparamagnetic nanocompasses

A scaleable chemical approach to functional nanoscale analogues of the magnetic compasses in magnetotactic bacteria is described. LiMo(3)Se(3)-Fe(3)O(4) nanowire-nanoparticle composites were synthesized by a reaction of 3-iodopropionic acid treated LiMo(3)Se(3) nanowire bundles with oleic acid-stabilized Fe(3)O(4) nanoparticles of 2.8, 5.3, and 12.5 nm size in tetrahydrofuran. Transmission electron micrographs show that the composite consists of Fe(3)O(4) nanoparticles attached to the surfaces of the 4-6 nm thick nanowire bundles. UV/vis spectra reveal absorptions from the nanowire (506 nm) and magnetite components (280-450 nm), and IR spectra show characteristic bands for the propionic acid linkers and for the residual oleic acid ligands on the magnetite particles. In the presence of excess oleic acid, the nanocomposites undergo rapid disassembly, suggesting that Fe(3)O(4) nanoparticles are bonded to nanowires via carboxylate groups from the linkers. Ultrasonication of a dispersion of the composite in THF produces individual LiMo(3)Se(3)-Fe(3)O(4) clusters, which are 340 +/- 107 nm long and 20 +/- 5 nm thick, depending on the sonication time and Fe(3)O(4) nanoparticle size. Field cooled and zero-field cooled magnetization measurements reveal that the blocking temperature (T(B) = 100 K) of the clusters with 5.3 nm Fe(3)O(4) is increased as compared to the free nanoparticles (T(B) = 30 K). Directional dipolar interactions in the clusters lead to magnetic anisotropy, which makes it possible to align the clusters in a magnetic field (900 Oe).     

Synthesis of Bilayer Surfactant-Coated Magnetic Nanoparticles for Application in Magnetic Fluid Hyperthermia

Nanocrystalline La_0.73Sr_0.27MnO₃ perovskite oxides with an average particle size of 26 nm were synthesized using the sol-gel method. To make water based magnetic fluid, the obtained nanoparticles were coated by self-organized bilayer surfactant containing oleic acid and sodium dodecyl sulfate as inner and outer layer, respectively. The bare and coated nanoparticles were characterized by x-ray powder diffraction, Fourier transform infrared spectroscopy, thermogravimetry, and transmission electron microscopy analyses. Calorimetric analysis was used to determine the heat generation efficiency of the prepared magnetic fluid under various alternating magnetic fields. The obtained results revealed that the maximum temperature achieved by the nanoparticles is in the therapeutic temperature range which enables these materials to be used as self-controlled heating agents in magnetic hyperthermia therapy.     

精氨酸功能化磁性纳米材料的制备及在磷酸化肽富集中的应用

以精氨酸修饰的磁性微球作为磁性固相萃取(MSPE)平台的载体, 结合基质辅助激光解吸电离飞行时间质谱(MALDI-TOF MS)技术, 实现了对复杂样品中低丰度磷酸化肽的分离富集. 采用场发射扫描电子显微镜、 Zeta电位测定、 红外光谱分析、 振动样品磁强计及X射线衍射分析等手段对合成的功能化磁性材料进行了表征. 选择β-酪蛋白酶解产物磷酸化肽为标准品, 在最佳实验条件下, 利用构建的MSPE-MS平台能够实现对磷酸化肽的高选择性和高灵敏度检测, 检出限为0.1 fmol. 实验结果表明, 经精氨酸修饰的磁性材料对牛奶样品中低含量的磷酸化肽具有较高的选择性, 所建立的方法适用于复杂样品的分离分析.     

Radiation synthesis of copper sulphide/poly(vinyl alcohol) nanocomposites films: an efficient and reusable catalyst for p-nitrophenol reduction

ABSTRACT

Copper sulphide nanoparticles (CuS NPs) were in situ synthesised via irradiation process, using Poly (vinyl alcohol) (PVA) as host polymeric matrices. The as-prepared CuS/PVA nanocomposite films were characterised by X-ray diffraction (XRD) spectroscopy, ultraviolet-visible (UV-VIS) spectroscopy, Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). Both UV-VIS spectra and X-ray diffraction patterns confirmed the formation of CuS nanoparticles. The FTIR spectrum indicates the coordination between CuS nanoparticles and the OH groups of the PVA chains. The TEM image showed that the obtained CuS nanoparticles have spherical shape, monodispersed and uniform particle size distribution. The CuS/PVA nanocomposite film was successfully applied in the reduction of p-nitrophenol into p-aminophenol as a catalyst using NaBH₄ as reducing agent. The catalytic test indicates that CuS/PVA nanocomposite film has high activity for the conversion of P-NP into P-AP and effectively recycled and reused for several times.     

Magnetic and Thermal Properties of Novel Poly(ether-amide)/Fe3O4 Nanocomposite Containing Phosphine Oxide Group

New poly(ether-amide) nanocomposite containing phosphine oxide was prepared via solution polymerization process from synthesized poly(ether-amide) and Fe₃O₄ nanoparticles in a solution of N,N-dimethylformamide. Uniform monodisperse Fe₃O₄ nanoparticles were synthesized at room temperature via a facile sonochemical reaction. Poly(ether-amide) (PEA) as the polymer matrix was synthesized from reaction of 1,4-(4-carboxy phenoxy)butane (1) and bis(3-amino phenyl)phenyl phosphine oxide (2) via a direct polycondensation reaction. Nanoparticle and nanocomposite were characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared. The effect of the presence of Fe₃O₄ nanoparticles on the thermal properties of PEA was studied using thermogravimetric analysis in nitrogen atmospheres. The magnetic properties of the sample were also investigated using an alternating gradient force magnetometer. We found that the Fe₃O₄ nanoparticles exhibit a ferromagnetic behaviour with a saturation magnetization of 59 emu/g and a coercivity of 104 Oe at room temperature. The coercivity of PEA/Fe₃O₄ nanocomposites is found to be 126 Oe, higher than 104 Oe which is obtained for Fe₃O₄.     

Solution synthesis of gadolinium nanoparticles

Gadolinium nanoparticles have been produced at subambient temperature by alkalide reduction. The nanoparticles display maxima in the temperature dependence of their magnetization, cooled in the absence of an applied external field, at T(max) of 5.0 and 17.5 K for unheated samples and samples annealed at 1000 degrees C for 4 h, respectively. Field cooled behavior deviates at temperatures slightly above T(max), increasing at lower temperature. Curie-Weiss law fits of the high-temperature data yield magnetic moments in close agreement with those expected for noninteracting Gd(3+) ions, suggesting that the behavior seen is due to a magnetic transition rather than superparamagnetism. Magnetization is linearly dependent on field at temperatures higher than 7-8 times T(max) and shows remanence-free hysteresis at lower temperature, suggesting metamagnetism. Some annealed samples show evidence of additional ferromagnetic interactions below approximately 170 K. Magnetic entropy curves generated from magnetization data are consistent with that expected for a paramagnet.