Impact of carbon dioxide on the surface tension of 1-hexanol aqueous solutions

Effects of carbon dioxide presence on the surface tension and adsorption kinetics of 1-hexanol solutions were investigated. Experiments were performed at a range of carbon dioxide vapor pressures and varying concentrations of 1-hexanol aqueous solution. Both dynamic and steady-state surface tensions of 1-hexanol aqueous solution were found to decrease with carbon dioxide pressure, and a linear relationship was observed between the steady-state surface tension and carbon dioxide pressure. To explain the experiments, adsorption and desorption of the two species (1-hexanol and carbon dioxide) from two sides of the vapor-liquid interface were considered. A modified Langmuir isotherm, the modified Langmuir equation of state and the modified kinetic transfer equation were developed. The resulting steady-state and dynamic surface tension data were modeled using the modified Langmuir equation of state and the modified kinetic transfer equation, respectively. Equilibrium constants and adsorption rate constants of 1-hexanol and carbon dioxide were evaluated through a minimization procedure for CO₂ pressures ranging from 0 to 690 kPa. From the steady-state modeling, the equilibrium parameters for 1-hexanol and carbon dioxide adsorption from vapor phase and liquid phase were found unchanged at different pressures of carbon dioxide. From the dynamic modeling, the adsorption rate constants for 1-hexanol and carbon dioxide from vapor phase and liquid phase were found to decrease with carbon dioxide pressure. Some fluctuations in the fitting parameters of the dynamic modeling (adsorption rate constants) were observed. These fluctuations may be due to experimental errors, or more likely the limitations of the model used. A major limitation of the model is related to large differences in adsorption/desorption between initial and final stages of the process, and a single set of property parameters cannot describe both initial and final states of the system. Variations may occur depending on which set of data, of initial or final states, is used in the model predictions over the entire time range.     

Synthesis and surface properties of anionic gemini surfactants with amide groups

Novel anionic gemini surfactants, 1,2-bis(N-beta-carboxypropanoyl-N-alkylamino)ethane (2CnenAm; n is hydrocarbon chain length of 6, 8, 10, 12, or 14), with two hydrocarbon chains, two carboxylate groups, and two amide groups, were synthesized by three-step reactions. Their solution properties were characterized by equilibrium and dynamic surface tension, steady-state fluorescence spectroscopy of pyrene, and dynamic light-scattering techniques. The surface tension measurements of 2CnenAm give low critical micelle concentrations (cmc), great efficiency in lowering the surface tension, and strong adsorption at air/water interface. Gemini surfactants behave normally with the logarithm of cmc decrease linearly with the chain length. In addition, adsorption and micellization behavior of 2CnenAm was estimated by parameter of pC20, cmc/C20, and standard free energy (DeltaG(0)mic and DeltaG(0)ads); they are significantly influenced by hydrocarbon chain length, and the adsorption is promoted more than the micellization as chain length becomes longer. The results of dynamic light-scattering and fluorescence quenching indicate that small micelles of 2CnenAm are observed at the concentrations above the cmc, and further large particles are also seen. Further, from the dynamic surface tension measurements, it is found that the shorter hydrocarbon chain length of 2CnenAm, the faster the rate of decrease of surface tension.     

Study of the surface properties and surface concentration of ionic liquid–alcohol mixtures

Surface properties for three binary mixtures containing a 1-butyl-3-methylimidazolium thiocyanate ([BMIM][SCN]) and a long-chain alcohol (1-butanol, 1-pentanol and 1-hexanol) were determined by surface tension data at the following temperatures: (298.15, 308.15, 318.15, 328.15 and 338.15) K. The surface tension data over the entire mole fraction range are correlated by the Fu et al.(FLW) and Myers-Scott (MS) models. There is good agreement between the experimental data and the results of correlations for 15 binary systems (the three systems at five temperatures) with an average relative error below 1.5%. In addition, the UNIFAC group contribution method is applied for calculation of activity coefficients of components in solution. Moreover, the relative adsorptions of alcohol at the air/liquid interface are determined using Gibbs adsorption isotherm. The obtained results show that the values of adsorption for mixtures of alcohols/[BMIM][SCN] increase with increasing the alkyl chain length of alcohol and decreasing temperature.     

Effect of temperature and composition on the density,viscosity, surface tension,and thermodynamic properties of binary mixtures of N-octylisoquinolinium bis{(trifluoromethyl)sulfonyl}imide with alcohols

Density and viscosity were determined for the binary mixtures containing the ionic liquid N-octylisoquinolinium bis{(trifluoromethyl)sulfonyl}imide ([C₈iQuin][NTf₂]) and 1-alcohol (1-butanol, 1-hexanol, and 2-phenylethanol) at five temperatures (298.15, 308.15, 318.15, 328.15, and 338.15) K and ambient pressure. The density and viscosity correlations for these systems were tested by an empirical second-order polynomial and by the Vogel–Fucher–Tammann equation. Excess molar volumes were described by the Redlich–Kister polynomial expansion. The density and viscosity variations with compositions were described by polynomials. Viscosity deviations were calculated and correlated by the Redlich–Kister polynomial expansions. The surface tensions of pure ionic liquid and binary mixtures of [C₈iQuin][NTf₂] with 1-hexanol were measured at atmospheric pressure at three temperatures (298.15, 308.15, and 318.15) K. The surface tension deviations were calculated and correlated by the Redlich–Kister polynomial expansion. The surface thermodynamic functions such as surface entropy and enthalpy were derived from the temperature dependence of the surface tension values. The critical temperature, parachor, and speed of sound for pure ionic liquid were described. A qualitative analysis on these quantities in terms of molecular interactions is reported. The obtained results indicate that ionic liquid interactions with alcohols are strong dependent on the special trend of packing effects and hydrogen bonding of this ionic liquid with hydroxylic solvents. As previously observed, an increase by a 1-alcohol carbon chain length leads to lower interactions on mixing.     

A Study of Dynamic Interfacial Properties as Related to Foaming Properties of Sodium 2,5-dialkyl Benzene Sulfonates

In this article, foaming properties and dynamic interfacial properties of a series of sodium 2,5-dialkyl benzene sulfonates in aqueous solutions were carried out to elucidate the relationship between foaming properties and dynamic interfacial properties. The properties of foams generated from bubbling air through different surfactant solutions were measured using a modified Bikerman device. The dynamic surface tension and surface dilational elasticity were obtained from an image analysis technique based on the oscillating bubble method. The surfactants molecular adsorption at the air/water interface was introduced with Rosen empirical equation and the rate of adsorption was determined from measurements of the dynamic surface tension. The surfactant with the longest alkyl chain shows the lowest dynamic surface activity, which lead to the lowest foam volume. The short ortho straight alkyl chain has little effect on the arrangement of molecules at the interface and the foam stability changes a little with the changing of the ortho alkyl chain length. The foam stability is correlated with both the higher surface dilational elasticity and the larger surface monolayer strength.     

The extent of molecular orientation at liquid/vapor interface of pyridine and its alkyl derivatives by molecular dynamics simulation

In this paper, molecular dynamics simulation was performed to investigate the liquid∕vapor interfacial structure of neat polar liquids. Large-scale ensembles of liquid pyridine and its alkyl derivatives, 4-methylpyridine and 4-ethylpyridine, were simulated by classical molecular dynamics at 298 K. For the liquid system of low polarity, the surface density profile of the atoms meet exactly at the middle of interfacial region, and atoms of hydrophobic nature can be hardly discriminated from hydrophilic ones in either vapor or liquid sides. For a liquid system of high polarity, the density profile of atoms with different nature is highly discriminated all over the interfacial region, and as the polarity increases, a dense region of atomic density is clearly developed in the subsurface region. The recognized bivariate method was also used to study the molecular orientational distribution quantitatively. Orientational analysis of the three liquid systems indicates that the pyridine ring plane in the outmost surface tends to be vertical. Its tendency in the innermost interfacial region is parallel. The orientational states available to 4-ethylpyridine and pyridine are discriminated by predicting the possibility of a bisector-wise tumbling for the ring plane in pyridine and a side-wise tumbling in 4-ethylpyridine. The orientational distribution maps explain the trend of experimental surface tension and surface entropy. As the dipole moment of these liquids increases with the alkyl chain length, the surface structural profile changes from a regular definite one to a surface of complex atomic structure involving a dense phase near the interface. The development of dense region in alkyl derivatives is the result of segregation of molecules due to the alkyl group, which is captured and discriminated by molecular dynamics simulation even when the length of a short alkyl chain is increased by one carbon atom.     

Micelle formation by N-alkyl-N-methylpyrrolidinium bromide in aqueous solution

The micellization of the ionic liquid N-alkyl-N-methylpyrrolidinium bromide (C(n)MPB, n = 12, 14 and 16) in aqueous solutions was investigated by surface tension measurements, electrical conductivity and static luminescence quenching. The effectiveness of the surface tension reduction (Π(cmc)), maximum surface excess concentration (Γ(max)) and the minimum area (A(min)) occupied per surfactant molecule at the air/water interface can be obtained from the surface tension measurements at 25 °C. The critical micelle concentration (cmc) at different temperatures and a series of thermodynamic parameters (ΔG, ΔH and ΔS) of micellization were evaluated from electrical conductivity measurements in the temperature range of 25-45 °C. The thermodynamic parameters show that the micelle formation is entropy-driven at low temperature and enthalpy-driven at high temperature. Furthermore, the micelle aggregation number (N(agg)) of C(n)MPB was calculated according to the Turro-Yekta method through static luminescence quenching and found that N(agg) (49, 55, and 59) increased with the hydrophobic chain length of C(n)MPB.     

Adsorptive separations for the recovery and purification of biobutanol

A?conceptual adsorption process for the recovery and purification of biobutanol is proposed. Different porous materials are tested on their ability to perform the adsorptive separations relevant to the process. The metal-organic framework ZIF-8, silicalite zeolite and active carbon were compared with respect to their adsorption capacity of 1-butanol dissolved in water, as obtained in static and dynamic conditions by respectively batch and breakthrough measurements at room temperature. Batch experimentation showed that other compounds present in a real ABE fermentation have no significant effect on the adsorption of 1-butanol on ZIF-8. The breakthrough separation of 1-butanol from an aqueous ABE mixture was performed with a ZIF-8 packed column. The desorption of 1-butanol from a saturated ZIF-8 packed column by a stepwise increase of the temperature to 423?K in combination with a purge of a nitrogen gas (60?ml/min) shows that 1-butanol desorbs at low temperature from ZIF-8. Adsorption isotherms of ethanol, 1-butanol and water in liquid phase on the zeolite SAPO-34 were determined by batch adsorption at 298?K. Also the separation of an ethanol/1-butanol mixture and the removal of ethanol from 1-butanol could be achieved with a SAPO-34 packed column. From this experimental work, two materials—ZIF-8 and SAPO-34—thus emerged as suitable adsorbents for the recovery and purification of biobutanol by adsorption.     

The interaction between sodium alkyl sulfate surfactants and the oppositely charged polyelectrolyte, polyDMDAAC, at the air-water interface: the role of alkyl chain length and electrolyte and comparison with theoretical predictions

The effect of alkyl chain length and electrolyte on the adsorption of sodium alkyl sulfate surfactants and the oppositely charged polyelectrolyte, polyDMDAAC, at the air-water interface has been investigated by surface tension and neutron reflectivity. The variations in the patterns of adsorption and surface tension behavior with alkyl chain length and electrolyte are discussed in the context of the competition between the formation of surface active surfactant/polyelectrolyte complexes and polyelectrolyte/surfactant micelle complexes in solution. A theoretical approach based on the law of mass action has been used to predict the surface effects arising from the competition between the formation of polyelectrolyte/surfactant surface and solution complexes and the formation of free surfactant micelles. This relatively straightforward model is shown to reproduce the principal features of the experimental results.     

Equilibrium and dynamic surface properties of long-chain quaternary ammonium hydroxides with different chain length and number

The equilibrium and dynamic surface tensions of five long-chain alkyl ammonium hydroxides (AAH) at the air/aqueous solution interface were investigated, and the effects of the length and number of alkyl chain on surface tensions had been discussed. With the increase of the length, the equilibrium surface tension (EST) increased from 28.65 to 40.52?mN/m. While, for the double chains at the critical micelle concentration (CMC), the EST decreased from 32.71 to 26.61?mN/m with the length increasing. In addition, the adsorption behaviors of the AAH were analyzed and the effective diffusion coefficients (D_eff) were calculated on basis of the Ward–Tordai equation. Moreover, the time required to attain the EST decreases with the increase of surfactant concentration. The longer the C–H chain is, the lower surface tension at initial concentration is. What’s more, the diffusion processing of the AAH to air/water interface mainly depends on the surfactant concentration, and the adsorption is controlled by diffusion mechanism in a dilute concentration, while under a high concentration the adsorption is controlled by mixed diffusion–kinetic mechanism.     

Equilibrium and dynamic surface tension properties of partially fluorinated quaternary ammonium salt gemini surfactants

The equilibrium and dynamic surface tension properties of a partially fluorinated quaternary ammonium salt gemini surfactant 1,2-bis[dimethyl-(3-perfluoroalkyl-2-hydroxypropyl)ammonium]ethane bromide (C(n)(F)C3-2-C3C(n)F, where n represents fluorocarbon chain lengths of 4, 6, and 8) were investigated, and the effects of the fluorocarbon chain length and the number of chains on them were discussed. The plot of the logarithm of the critical micelle concentration (cmc) against the fluorocarbon chain length for C(n)(F)C3-2-C3C(n)F showed a linear decrease with an increase in chain length. On the basis of the slope of this plot, it was found that the variation in cmc with respect to the chain length is large for fluorinated gemini surfactants. The surface tension at the cmc decreased significantly; this surface tension value is lower than that of conventional fluorinated monomeric surfactants. In particular, the lowest value was 13.7 mN m(-1) for n = 8. Furthermore, it was confirmed that the kinetics of adsorption at the interface decrease with an increase in the fluorocarbon chain length and the concentration.     

Mass transfer model of triethylamine across the n-decane/water interface derived from dynamic interfacial tension experiments

This publication presents a detailed experimental and theoretical study of mass transfer of triethylamine (TEA) across the n-decane/water interface. In preliminary investigations, the partition of TEA between n-decane and water is determined. Based on the experimental finding that the dissociation of TEA takes place in the aqueous and in the organic phase, we assume that the interfacial mass transfer is mainly affected by adsorption and desorption of ionized TEA molecules at the liquid/liquid interface. Due to the amphiphilic structure of the dissociated TEA molecules, a dynamic interfacial tension measurement technique can be used to experimentally determine the interfacial mass transport. A model-based approach, which accounts for diffusive mass transport in the finite liquid bulk phases and for adsorption and desorption of ionized TEA molecules at the interface, is employed to analyze the experimental data. In the equilibrium state, the interfacial tension of dissociated TEA at the n-decane/water interface can be adequately described by the Langmuir isotherm. The comparison between the theoretical and the experimental dynamic interfacial tension data reveals that an additional activation energy barrier for adsorption and desorption at the interface has to be regarded to accurately describe the mass transport of TEA from the n-decane phase into the aqueous phase. Corresponding adsorption rate constants can be obtained by fitting the theoretical predictions to the experimental data. Interfacial tension measurements of mass transfer from the aqueous into the organic phase are characterized by interfacial instabilities caused by Marangoni convection, which result in an enhancement of the transfer rate across the interface.     

Vapor–liquid equilibrium of binary mixtures of trichloroethylene with 1-pentanol, 2-methyl-1-butanol and 3-methyl-1-butanol at 100 kPa

Isobaric vapor–liquid equilibria (VLE) have been obtained for the systems trichloroethylene+1-pentanol, trichloroethylene+2-methyl-1-butanol and trichloroethylene+3-methyl-1-butanol at 100 kPa using a dynamic still. The experimental error in temperature is ±0.1 K, in pressure ±0.1 kPa, and in the liquid and vapor mole fraction ±0.001. The three systems satisfy the point-to-point thermodynamic consistency test. All the systems show positive deviations from ideality. The data have been correlated with the Margules, van Laar, Wilson, NRTL and UNIQUAC equations.     

Direct observation of chemical oscillation at a water/nitrobenzene interface with a sodium-alkyl-sulfate system.

The oscillation of the interfacial tension and electrical potential at a water/nitrobenzene interface was observed with homologous anionic surfactant molecules, sodium-alkyl-sulfates. Concerning small molecules with a short hydrophobic carbon chain, the oscillation period and amplitude decreased with a decrease of the length of the alkyl chain. On the other hand, when surfactant molecules with a long hydrophobic carbon chain were used, no remarkable periodic oscillation occurred after the first oscillation. In all systems, an interfacial flow by Marangoni convection was observed when the oscillation took place. By monitoring the movement of carbon powder scattered on the liquid/liquid interface with a CCD camera, we could observe that the liquid/liquid interface expanded outward from the area on which the surfactant molecules adsorbed when the oscillation occurred. When the small molecule was used, the speed of expansion of the interface (flow speed) was small and shrinkage followed by expansion of the interface repeatedly occurred. However, when the large molecule was used, the flow speed was large and expansion occurred only one time. These results show that hydrodynamic factors and surface activities are important in chemical oscillation systems.     

Transient Surface Tension of an Expanding Liquid Sheet

We address the problem of dynamic surface tension using measurements of sheet diameters that results from the impact of a liquid jet of diameter d(0) on a small disk of diameter d(i) (d(i)/d(0) approximately 4). At low velocities, the sheet diameter D is related to d(0) by the Weber number We, constructed with the liquid density rho, the jet velocity u(0), and the surface tension sigma at the rim: D/d(0)=18 We=18 [rho u(0)(2)/(sigma/d(0))]. This relation expresses the equilibrium between inertial forces and surface tension forces at the sheet rim. When a surfactant has been dissolved in the bulk of the liquid prior to the formation of the initial jet, the rim surface tension, and therefore the sheet diameter, depends on the amount of surfactant adsorbed at the rim. This amount is fixed by a competition between surface formation induced by radial extension and repopulation of the liquid interface in surfactant. The experimental setup proposed here provides a method to measure dynamic surface tension from sheet diameter measurements and symmetrically to monitor the adsorption of a surfactant on a liquid surface. The available adsorption time ranges from 10 to 100 ms. Experimental data obtained with two surfactants are in agreement with a model of a diffusion-controlled adsorption at the interface. Copyright 2000 Academic Press.     

Study on the Surface Property of Surfactant Ionic Liquids Solutions

The surfactant TX-100 can be dissolved in ionic liquid bmimPF6 and decrease the surface tension of 1-buty1-3-methylimidazolium hexafluorophosphate (bmimPF6) solutions. Here, we confirmed that in this new system, the pure solvents need rearrangement at the air-wate rinterface at the initial stage. The dynamic surface tension (DST) study shows that at the initial adsorption stage, the adsorption model of surfactant accords with the diffusion-controlled adsorption mechanism, and the dilute ionic liquids solutions is further close to the diffusion-controlled adsorption.     

Nucleation of ethanol, propanol, butanol, and pentanol: A systematic experimental study along the homologous series

We present homogeneous vapor-liquid nucleation rates of the 1-alcohols (C(n)H(2n+1)OH, n = 2-4) measured in the well-established two-valve nucleation pulse chamber as well as in a novel one-piston nucleation pulse chamber at temperatures between 235 and 265 K. The nucleation rates and critical cluster sizes show a very systematic behavior with respect to the hydrocarbon chain length of the alcohol, just as their thermo-physical parameters such as surface tension, vapor pressure, and density would suggest. For all alcohols, except ethanol, predictions of classical nucleation theory lie several orders of magnitude below the experimental results and show a strong temperature-dependence typically found in nucleation experiments. The more recent Reguera-Reiss theory [J. Phys. Chem. B 108(51), 19831 (2004)] achieves reasonably good predictions for 1-propanol, 1-butanol, and 1-pentanol, and independent of the temperature. Ethanol, however, clearly shows the influence of strong association between molecules even in the vapor phase. We also scaled all experimental results with classic nucleation theory to compare our data with other data from the literature. We find the same overall temperature trend for all measurement series together but inverted and inconsistent temperature trends for individual 1-propanol and 1-butanol measurements in other devices. Overall, our data establishe a comprehensive and reliable data set that forms an ideal basis for comparison with nucleation theory.     

Effect of Temperature and Composition on the Surface Tension and Thermodynamic Properties of Binary Mixtures of Boltorn U3000 with Alcohols and Ether

The surface tension of the pure hyperbranched polymer, Boltorn U3000, and binary mixtures of Boltorn U3000 with alcohols (1-butanol, 1-hexanol) have been measured at atmospheric pressure in the range of temperatures from 298.15 K to 328.15 K, or of Boltorn U3000 with methyl-tert-butylether (MTBE) in the range of temperatures from 298.15 K to 318.15 K. These measurements have been provided to complete information of the influence of temperature on surface tension for the selected polymer, which was chosen as a possible new entrainer in extraction processes. The surface thermodynamic functions such as surface entropy and enthalpy have been derived from the temperature dependence of the surface tension, as well as the critical temperature, parachor and speed of sound for the pure polymer. The influences investigated here include the effects of the alkyl chain length of an alcohol and solvent polarity on the surface tension.     

Sugar-based gemini surfactants with peptide bonds-synthesis, adsorption, micellization, and biodegradability

The sugar-based gemini surfactant with peptide bonds, N,N'-bisalkyl-N,N'-bis[2-(lactobionylamide)ethyl]hexanediamide (2C(n)peLac, in which n represents hydrocarbon chain lengths of 12 and 16), was synthesized by reacting adipoyl chloride with the corresponding monomeric surfactant N-alkyl-N'-lactobionylethylenediamine (C(n)peLac), which was obtained by reacting ethylenediamine with alkyl bromide and lactobionic acid. The adsorption and micellization properties of C(n)peLac and 2C(n)peLac were characterized by the measurement of their equilibrium and dynamic surface tension, steady-state fluorescence using pyrene as a probe, dynamic light scattering (DLS), and time-resolved fluorescence quenching (TRFQ), and their biodegradability was also investigated. The critical micelle concentration (cmc) decreases with an increase in the hydrocarbon chains from monomeric to gemini surfactants, whereas it increases with an increase in the chain length from 12 to 16 for both systems. The increases in both the hydrocarbon chain and the chain length of sugar-based surfactants reduce surface activities such as the ability to lower the surface tension, the occupied area per molecule, and the adsorption rate at the air/water interface. The sugar-based surfactants C(n)peLac and 2C(n)peLac exhibit unique aggregation behavior in aqueous solution. The DLS results indicate that the apparent hydrodynamic diameter of C(n)peLac micelles decreases sharply with increasing concentration, whereas that of 2C(n)peLac micelles decreases gradually. From the TRFQ measurement, it was observed that, as concentration increases, the aggregation numbers are almost constant for C(n)peLac, whereas they increase for 2C(n)peLac. These results imply that loosely packed micelles formed by sugar-based surfactants become tightly packed micelles as the concentration increases. Furthermore, it was found that 2C(n)peLac shows lower biodegradability than does C(n)peLac because it contains tertiary amines in the molecule.     

High-pressure phase equilibria for the carbon dioxide–2-methyl-1-butanol,carbon dioxide–2-methyl-2-butanol,carbon dioxide–2-methyl-1-butanol–water,and carbon dioxide–2-methyl-2-butanol–water systems

High-pressure vapor–liquid equilibria for the binary carbon dioxide–2-methyl-1-butanol and carbon dioxide–2-methyl-2-butanol systems were measured at 313.2 K. The phase equilibrium apparatus used in this work is of the circulation type in which the coexisting phases are recirculated, on-line sampled, and analyzed. The critical pressure and corresponding mole fraction of carbon dioxide for the binary carbon dioxide–2-methyl-1-butanol system at 313.2 K were found to be 8.36 MPa and 0.980, respectively. The critical point of the binary carbon dioxide–2-methyl-2-butanol was also found 8.15 MPa and 0.970 mole fraction of carbon dioxide. In addition, the phase equilibria of the ternary carbon dioxide–2-methyl-1-butanol–water and carbon dioxide–2-methyl-2-butanol–water systems were measured at 313.2 K and several pressures. These ternary systems showed the liquid–liquid–vapor phase behavior over the range of pressure up to their critical point. The binary equilibrium data were all reasonably well correlated with the Redlich–Kwong (RK), Soave–Redlich–Kwong (SRK), Peng–Robinson (PR), and Patel–Teja (PT) equations of state with eight different mixing rules the van der Waals, Panagiotopoulos–Reid (P&R), and six Huron–Vidal type mixing rules with UNIQUAC parameters.