Friction and wear properties of ZrO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> composite nanoparticles

In this article, the lubrication properties of ZrO₂/SiO₂ composite nanoparticles modified with aluminum zirconium coupling agent as additives in lubricating oil under variable applied load and concentration fraction were reported. It was demonstrated that the modified nanoparticles as additives in lubrication can effectively improve the lubricating properties. Under an optimized concentration of 0.1 wt%, the average friction coefficient was reduced by 16.24%. This was because the nanoparticles go into the friction zone with the flow of lubricant, and then the sliding friction changed to rolling friction with a result of the reduction of the friction coefficient.     

Optical and magnetooptical properties of CoFeB/SiO<Subscript>2</Subscript> and CoFeZr/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> granular magnetic nanostructures

The optical and magnetooptical properties of the new granular nanocomposites (CoFeB)/(SiO₂) and (CoFeZr)/(Al₂O₃), which are grains of amorphous ferromagnetic alloys embedded in dielectric matrices, have been studied. The dependence of the optical, magnetooptical, and magnetic properties of the nanocomposites on their qualitative and quantitative composition, as well as on the conditions of their preparation, was investigated. Spectra of the dielectric functions ε = ε₁ ? iε₂ were obtained by the ellipsometric method in the range 0.6–5.4 eV. Above 4.2 eV, the absorption coefficient of the (CoFeB)/(SiO₂) composites was found to be close to zero for all magnetic-grain concentrations. The polar Kerr effect measured at a photon energy of 1.96 eV in dc magnetic fields of up to 15 kOe reaches values as high as 0.25°–0.3° for these nanocomposites and depends only weakly on the conditions of preparation. On the other hand, the (CoFeZr)/(Al₂O₃) nanostructures reveal a considerable difference in the concentration dependences of the Kerr effect between samples prepared in a dc magnetic field and in zero field.     

Preparation and investigation of composite SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> films

SiO₂-TiO₂ films [Si:Ti = 1:(0.06–2.3)] are obtained by the sol-gel method. The structural and photoluminescent properties of the films and powders heat-treated at different temperatures are studied. It is shown that after 700°C the composite consists of TiO₂ crystallites that are structurally similar to anatase and distributed in an amorphous SiO₂ matrix. The photoluminescence spectra have maxima at 450–500 nm. The photoluminescence intensity depends on the treatment temperature and TiO₂ content. __________ Translated from Zhurnal Prikladnoi Spektroskopii Vol. 74, No. 3, pp. 357–361, May–June, 2007.     

Self-organization of bimetallic PdAu nanoparticles on SiO<Subscript>2</Subscript> surface

Bimetallic PdAu nanoparticles on SiO₂ substrate were produced by a sequential room-temperature sputtering deposition method. By the atomic force microscopy technique we studied the nanoparticles self-organization mechanisms in various conditions. First, Pd nucleation and growth proceeds at the substrate defects and the Pd nanoparticles density increase rapidly. During the second sputtering deposition, Au atoms adsorb on the SiO₂ and diffuse toward Pd nanoparticles without forming new nuclei. The Au atoms are trapped by the preformed Pd nanoparticles, forming PdAu bimetallic nanoparticles which size increases. Furthermore, fixing the amount of deposited Pd and increasing the amount of deposited Au, we analyzed the evolution of the PdAu film surface morphology: we observe that the PdAu grows initially as three-dimensional islands; then the PdAu film morphology evolves from compact three-dimensional islands to partially coalesced worm-like structures, followed by a percolation morphology and finally to a continuous and rough film. The application of the interrupted coalescence model allowed us to evaluate the critical mean island diameter R _c ≈ 2.8 nm for the partial coalescence process. The application of the dynamic scaling theory of growing interfaces allowed us to evaluate the dynamic growth exponent β = 0.21 ± 0.01 from the evolution of the film surface roughness. Finally, fixing the amount of deposited Pd and Au we studied the self-organization mechanism of the PdAu nanoparticles induced by thermal processes performed in the 973–1173 K temperature range. The observed kinetic growth mechanism is consistent with a surface diffusion-limited ripening of the nanoparticles with a temperature-dependent growth exponent. The dependence of the growth exponent on the temperature is supposed to be linked to the variation with the temperature of the characteristics of the PdAu alloy. The activation energy for the surface diffusion process was evaluated in 0.54 ± 0.03 eV.     

Si/SiO<Subscript>2</Subscript> core shell clusters probed by Raman spectroscopy

Using a pulsed microplasma source, clusters were produced through the ablation of a Si cathode and successive supersonic expansion. The Si cluster beam was deposited onto different substrates and the partial oxidation of the cluster surface avoided the growth of large agglomerates, preserving their nanocrystalline morphology. Micro-Raman spectroscopy was used for an accurate size diagnosis of the deposited nanoparticles. The size of the Si dots ranges between 2 and about 15 nm. The Si dots appear to have a Si oxide shell, as confirmed also by structural and compositional analysis through transmission electron microscopy and atomic force microscopy. Double Raman peaks were attributed to small Si agglomerates having a thin substoichiometric Si-O interface.     

Ferroelectrical properties of SiO<Subscript>2</Subscript>-TGS nanocomposite

Dielectric properties of the composites based on nanodisperse silica hydrosol and ferroelectric triglycinesulfate (TGS) are investigated. The studies allow us to expect the presence of the ferroelectric state in the composites.     

The effect of packing density on luminescence of amorphous SiO<Subscript>2</Subscript> nanoparticles

Photoluminescence of amorphous SiO₂ nanoparticles compressed in the form of tablets is studied under exposure to UV radiation. The observed luminescence spectrum is a broad band extending from the excitation wavelength to 700 nm and with a maximum at ~470 nm. The spectrum can be decomposed into two Gaussian components with maxima at ~460 and ~530 nm. As the pressure applied for sample preparation increases, the integrated intensities of these bands change in opposite directions—the intensity of the short-wavelength band increases, while that of the long-wavelength band decreases. It is concluded that these bands are due to different luminescence centers of silicon dioxide located on the surface and in the bulk of SiO₂ nanoparticles.     

The influence of Fe,Cu, SiO<Subscript>2</Subscript>, TiO<Subscript>2</Subscript>, and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles in aqueous solution on proton relaxation times

Measurements of proton nuclear spin-spin and spin-lattice relaxation times are applied for determining the concentration of solid-phase nanoparticles in nanofluids. This approach is tested for metal oxides SiO₂, TiO₂, Al₂O₃ and metal-carbon nanoparticles of 3d-metals Fe and Cu. It is shown that the sensitivity of the method for determining concentrations of 3d-metals is much higher than for oxides (by 2–4 orders of magnitude). It is revealed that measurement of the proton spin-spin relaxation time allows one to determine the concentration of Cu nanoparticles to 0.0001 mg/ml and that of Fe nanoparticles to 0.00001 mg/ml.     

RETRACTED ARTICLE: Refractive-index tailoring and morphological evolutions in Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite thin films

Refractive-index tailoring and morphological evolutions in two different thin film composite systems of gadolinia–silica (Gd₂O₃:SiO₂) and zirconia–silica (ZrO₂:SiO₂) deposited through reactive electron-beam codeposition processes are discussed in this research paper. For Gd₂O₃:SiO₂ the refractive-index tuning has been achieved from 1.45 to 2.18, whereas in the case of ZrO₂:SiO₂ the achieved tunable range is from 1.45 to 2.45 in the ultraviolet region. Under certain compositional mixings with lower silica fractions both the systems demonstrated relative microstructural and morphological densifications. Such evolutions were very successfully derived through phase-modulated ellipsometry and atomic force microscopy. The composition-dependent refractive-index tailoring and microstructural densifications have been investigated by adopting Tauc–Lorentz and single-effective-oscillator models. The morphological correlation functions have also very aptly supported such evolutions in these composite films. These experimental results indicate their favourable properties and applicability down to the extreme ultraviolet wavelength region of the electromagnetic spectrum. PACS 42.79.Wc; 78.66.-w; 78.20.Ci; 61.16.Ch; 42.70.-a;68.55.-a; 68.35.Bs; 81.15.Ef     

Mössbauer studies of magnetic Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> nanocomposites

A large variety of glass and glass ceramics may be obtained by sol-gel process from hydrolysis of tetraethoxysilane. The transformation involves hydrolysis and polycondensation reactions leading to the growth of clusters that eventually collide together to form a gel. The structure and properties of the final product have been found to be strongly dependent on the initial conditions of preparation. Silica nanocomposites based on Fe₂O₃/SiO₂ were prepared with the help of ultrasonic activation and subsequent annealing in nitrogen atmosphere or air with concentrations of iron oxide of about 20 to 30wt.%.     

Structure and optical properties of ZnSe/SiO<Subscript>2</Subscript> layered nanocomposites

Structure and optical properties of ZnSe/SiO₂ layered nanocomposites obtained using microwave magnetron sputtering have been studied. The nanocomposites are X-ray amorphous at relatively small thicknesses of the zinc selenide layers. When the thickness of the zinc selenide layers exceeds 20 Å, ZnSe/SiO₂ films contain SiO₂ amorphous phase and zinc selenide cubic nanocrystallites. It has been demonstrated that the thickness of zinc selenide layers affects the microstresses, refractive index, and band gap.     

A computer study of the Raman spectra of the (GaN)<Subscript>129</Subscript>, (SiO<Subscript>2</Subscript>)<Subscript>86</Subscript>, and (GaN)<Subscript>54</Subscript>(SiO<Subscript>2</Subscript>)<Subscript>50</Subscript> nanoparticles

The Raman spectra of the (GaN)₁₂₉, (SiO₂)₈₆, and (GaN)₅₄(SiO₂)₅₀ nanoparticles were calculated using the molecular dynamics method. The spectrum of (SiO₂)₈₆ had three broad bands only, whereas the Raman spectrum of (GaN)₁₂₉ contained a large number of overlapping bands. The form of the Raman spectrum of (GaN)₅₄(SiO₂)₅₀ was determined by the arrangement of the GaN and SiO₂ components in it. The nanoparticle with a GaN nucleus had a continuous fairly smooth spectrum over the frequency range 0 ≤ ω ≤ 600 cm⁻¹, whereas the spectrum of the nanoparticle with a SiO₂ nucleus contained well-defined bands caused by vibrations of groups of atoms of different kinds and atoms of the same kind.     

Electrical conductivity and dielectric properties of SiO<Subscript>2</Subscript> nanoparticles dispersed in conducting polymer matrix

Electrical and dielectric properties of conducting polypyrrole–wide band gap silica (PPY–SiO₂) nanocomposites have been investigated as a function of temperature and frequency for different concentrations of polypyrrole. The average grain size of the nanocomposites is in the range of 40–80 nm. Impedance spectra reveal two distorted semicircles corresponding to grain and grain boundary effects. The magnitude of conductivity and its temperature variation are significantly different from polypyrrole and silica. A very large dielectric constant of about 4800 at 30 kHz and at room temperature has been observed for the highest concentration of silica. Inhomogeneous behavior of nanocomposites gives rise to high dielectric constant.     

Plasmachemical synthesis and basic properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

Cobalt-ferrite (CoFe₂O₄) nanoparticles (CFNPs) are obtained using direct plasmachemical synthesis in the plasma of a low-pressure arc discharge. The formation of the CFNPs with an average size of 9 nm and a narrow granulometric composition is established employing the methods of X-ray structure analysis and transmission microscopy. The CFNP behavior upon high-temperature annealing is analyzed. The CFNP functional groups are determined using the infrared Fourier spectrum. The results of the X-ray energy dispersion confirm the correspondence of the ratio of the number of atoms of each material to the nominal stoichiometry. The basic magnetic properties of the obtained and annealed samples are investigated at room temperature using the vibrating spectrum magnetometry (VSM).     

Iron nanoparticles in amorphous SiO<Subscript>2</Subscript>: X-ray emission and absorption spectra

The local structure of the chemical bond of iron ions implanted into SiO₂ glasses (implantation energy, 100 keV; fluence, 1 × 10¹⁶ cm^?2) is investigated using x-ray emission and absorption spectroscopy. The Fe L x-ray emission and absorption spectra are analyzed by comparing them with the corresponding spectra of reference samples. It is established that iron nanoparticles implanted into the SiO₂ vitreous matrix are in an oxidized state. The assumption is made that the most probable mechanism of transformation of iron nanoparticles into an oxidized state during implantation involves the breaking of Si-O-Si bonds with the formation of Si-Si and Fe-O bonds.     

Hydrothermal synthesis and magnetic properties of CuSb<Subscript>2</Subscript>O<Subscript>6</Subscript> nanoparticles and nanorods

Nanoparticles and nanorods of CuSb₂O₆ are prepared by hydrothermal method and its high temperature α-phase is stabilized at room temperature. The average size of the nanoparticles is ca. 13.7 nm. The nanorods, with a width of ca. 20 nm and an aspect ratio of ca. 5, are the agglomerates composing of smaller nanoparticles with an average size of ca. 8.3 nm. Compared with the high temperature α-phase of bulk sample at 400 K, the lattice of nanophases elongated in ab plane and compressed along c direction. The CuSb₂O₆ nanoparticles exhibit predominant paramagnetic phenomenon. The difference in magnetic properties of the nanoparticles and nanorods indicates the interfacial interaction of agglomerated nanoparticles.     

Structural and magnetic properties of size-controlled Mn<Subscript>0.5</Subscript>Zn<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles and magnetic fluids

Mn_0.5Zn_0.5Fe₂O₄ ferrite nanoparticles with tunable Curie temperature and saturation magnetization are synthesized using hydrothermal co-precipitation method. Particle size is controlled in the range of 54 to 135 Å by pH and incubation time of the reaction. All the particles exhibit super-paramagnetic behaviour at room temperature. Langevin’s theory incorporating the interparticle interaction was used to fit the virgin curve of particle magnetization. The low-temperature magnetization follows Bloch spin wave theory. Curie temperature derived from magnetic thermogravimetric analysis shows that Curie temperature increases with increasing particle size. Using these particles magnetic fluid is synthesized and magnetic characterization is reported. The monolayer coating of surfactant on particle surface is confirmed using thermogravimetric measurement. The same technique can be extended to study the magnetic phase transition. The Curie temperature derived using this measurement complies with the low-temperature magnetic measurement. The room-temperature and high-temperature magnetization measurements are also studied for magnetic fluid systems. The magnetic parameters derived for fluid are in good agreement with those obtained for the particle system.     

The enhanced catalytic degradation of SiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/C@TiO<Subscript>2</Subscript> photo-Fenton system on p-nitrophenol

Heterogeneous photo-Fenton SiO₂/Fe₃O₄/C@TiO₂ (SFCT) catalyst with a core-multishell structure and a diameter of about 550 nm was successfully prepared and was characterized by scanning electron microscopy (SEM), TEM, XRD, Raman, and Fourier transform infrared (FT-IR). The results illustrated that anatase TiO₂ coexisted with rutile TiO₂, in which the anatase phase was the main crystal phase. In addition, the catalytic activity of SFCT catalyst had been evaluated in the catalytic degradation on p-nitrophenol (PNP). The influence factors on the PNP degradation, including SFCT component ratio (m _SFC/ m _TiO2), H₂O₂ dosage, solution pH, and PNP concentration, had been investigated. And the contrast experiments about the photo-Fenton catalytic mechanism revealed that the SFCT-2 catalyst possessed a superior activity in the neutral environment due to the optimal activity matching between Fe₃O₄ and TiO₂, and it exhibited the stable catalytic performance after five successive recycles. Therefore, the SFCT-2 catalyst had a promising application for the photo-Fenton degradation of organic contaminant.     

On the magnetic properties of Pr[Mn(CN)<Subscript>6</Subscript>]. 4H<Subscript>2</Subscript>O

A Prussian Blue type compound of the nominal composition Pr[Mn(CN)₆].4H₂O has been prepared. It is shown that the compound exhibits ferrimagnetism with a Curie temperature T_C=38.9 K. Observed magnetic relaxation displays a logarithmic behavior.     

Casimir friction force between a SiO<Subscript>2</Subscript> probe and a graphene-coated SiO<Subscript>2</Subscript> substrate

The possibility of mechanical detection of Casimir friction with the use of a noncontact atomic force microscope is discussed. A SiO₂ probe tip located above a graphene-coated SiO₂ substrate is subjected to the frictional force caused by a fluctuating electromagnetic field produced by a current in graphene. This frictional force will create the bend of a cantilever, which can be measured by a modern noncontact atomic force microscope. Both the quantum and thermal contributions to the Casimir frictional force can be measured using this experimental setup. This result can also be used to mechanically detect Casimir friction in micro- and nanoelectromechanical systems.