基板界面对PS/PMMA共混物薄膜相逆转组成比的影响

近年来高分子共混体系中的界面、表面效应逐渐引起了越来越多研究者的兴趣 .人们发现 ,当共混物薄膜厚度减至一定程度时 ,聚合物共混物薄膜中的相形态、相容性及相分离动力学与本体中有较大的不同[1～ 3] .基板界面作用对共混薄膜体系的热力学、动力学行为产生很大的影响 .我们以往的研究 [4 ,5]也发现 ,PP/EVAc(70 /30 )共混体系退火过程中 ,基板界面 (如玻璃 )作用可大大加速分散相(EVAc)粒子的粗化凝聚过程 .本研究用聚甲基丙烯酸甲酯和聚苯乙烯共混物的四氢呋喃溶液在不同基板介质 (如玻璃基板 ,PP基板 )上成膜 ,用相差显微镜观测了…     

Rheological,mechanical and morphological properties of thermoplastic vulcanizates based on NR‐g‐PMMA/PMMA blends

Graft copolymer of natural rubber and poly(methyl methacrylate) (NR‐g‐PMMA) was prepared using semi‐batch emulsion polymerization technique via bipolar redox initiation system. It was found that the grafted PMMA increased with the increase of methyl methacrylate (MMA) concentration used in the graft copolymerization. The NR‐g‐PMMA was later used to prepare thermoplastic vulcanizates (TPVs) by blending with PMMA through dynamic vulcanization technique. Conventional vulcanization (CV) and efficient sulphur vulcanization (EV) systems were studied. It was found that the CV system provided polymer melt with lower shear stress and viscosity at a given shear rate. This causes ease of processability of the TPVs via extrusion and injection molding processes. Furthermore, the TPVs with the CV system showed higher ultimate tensile strength and elongation. The results correspond to the morphological properties of the TPVs. That is, finer dispersion of the small vulcanized rubber particles were observed in the PMMA matrix. Various blend ratios of the NR‐g‐PMMA/PMMA blends using various types of NR‐g‐PMMA (i.e. prepared using various percentage molar ratios of NR and MMA) were later studied via dynamic vulcanization by a conventional sulphur vulcanization system. It was found that increasing the level of PMMA caused increasing trend of the tensile strength and hardness properties but decreasing level of elongation properties. Increasing level of the grafted PMMA in NR molecules showed the same trend of mechanical properties as in the case of increasing concentration of PMMA used as a blend component. From morphological studies, two phase morphologies were observed with a continuous PMMA phase and dispersed elastomeric phase. It was also found that more finely dispersed elastomeric phase was obtained with increasing the grafted PMMA in the NR molecules. Copyright © 2005 John Wiley & Sons, Ltd.     

Blends of poly(methyl methacrylate) (PMMA) with PMMA ionomers: Mechanical properties

Rigid–rigid blends made of ionomer and ionomer precursor polymer, based on poly(methyl methacrylate) (PMMA), have been investigated. Two series of blends have been prepared for studying mechanical properties. In one series, dynamic mechanical properties were determined over a wide range of temperatures. As the weight fraction of the ionomer was increased, there was a modest increase of modulus at ambient temperature and a very large increase in the rubbery modulus at elevated temperatures above the glass transition temperature of PMMA. In a second series of tests, tensile stress–strain measurements, made at an ambient temperature, were carried out over a wide range of blend compositions. For all blends tested, the mechanical properties exhibited a synergistic enhancement, i.e., average values of modulus, strength and fracture energy were all higher than expected based on the rule of mixtures. Measurements of fracture toughness also exhibited synergy, with a maximum value, higher than the value of either blend component, being attained in blends containing about 30 wt % of the PMMA ionomer. These results are interpreted in terms of a higher resistance to fracture of the more chain-entangled ionomer phase and good interfacial adhesion between the two components of the blend. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1235–1245, 1998     

Miscibility and morphologies of poly(arylene ether phenyl phosphine oxide/sulfone) copolymer/vinyl ester resin mixtures and their cured networks

Nonreactive bisphenol A‐based poly(arylene ether triphenyl phosphine oxide/diphenyl sulfone) statistical copolymers and a poly(arylene ether triphenyl phosphine oxide) homopolymer, each having a number‐average molecular weight of about 20 kg/mol, were synthesized and solution‐blended with a commercial dimethacrylate vinyl ester resin. Free‐radical cured systems produced morphologies that were a function of both the amount of phosphonyl groups and the weight percentage of the copolymers. For example, highly hydrogen‐bonded poly(arylene ether phenyl phosphine oxide) homopolymer/vinyl ester resin mixtures were homogeneous in all proportions both before and after the formation of networks. Copolymers containing low amounts (≤30 mol %) of the phosphonyl groups displayed phase separation either before or during cure. The phase‐separated cured materials generally had phase‐inverted morphologies, such as a continuous thermoplastic copolymer phase and a particulate, discontinuous vinyl ester network phase, except for systems containing a very low copolymer content. The resin modified with a copolymer containing 30 mol % phosphine oxide comonomer showed improved fracture toughness, suggesting the importance of both phase separation and good adhesion between the thermoplastic polymer and the crosslinked vinyl ester filler phase. The results suggested that the copolymers with high amounts of phosphine oxide should be good candidates for interphase sizing materials between a vinyl ester matrix and high‐modulus carbon fibers for advanced composite systems. Copolymers with low amounts of phosphonyl groups can produce tough, vinyl ester‐reinforced plastics. The char yield increases with the concentration of bisphenol A poly(arylene ether phosphine oxide) content, suggesting enhanced fire resistance. The incorporation of thermoplastic copolymers sustains a high glass‐transition temperature but does not significantly affect the thermal degradation onset temperature. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2409–2421, 2000     

Low velocity impact and pseudo-ductile behaviour of carbon/glass/epoxy and carbon/glass/PMMA hybrid composite laminates for aircraft application at service temperature

Carbon/glass hybrid composite (CGHC) laminates are some of the most promising composites for lightweight applications. Sometimes these laminates are used in warm environment, such as aircraft frame structures, and this may affect their performance. In order to investigate this issue, the present research aims to study the effect of temperatures on the impact behavior and pseudo-ductile behaviour of CGHC in presence of different types of thermosets “epoxy” and thermoplastic “acrylic poly-methyl methacrylate-PMMA”. The experiments were started with making of CGHC laminates from different stacking sequences of unidirectional carbon and woven glass fibre layers, using a vacuum-assisted resin transfer method followed by curing treatment. In addition to CGHC laminates, four other neat batches (Carbon/epoxy, Carbon/PMMA, Glass/epoxy, Glass/PMMA) were prepared for comparison. The low velocity impact behaviour of the fabricated panels was evaluated at high temperatures (60 °C and 80 °C) according to ISO 6603-2 standard, using drop tower, while pseudo-ductile behaviour and ductility index (DI) of the specimens were estimated based on the measured total energy and elastic energy. Also, the low-velocity impact response was modeled mathematically based on a modified energy-balance model to predict the absorbed energies. Finally, the failure mechanisms were examined using optical microscope to determine the influence of these damage growth on DI of the composites under different temperatures. The results showed that the impact energy response of both hybrid composites i.e. epoxy and PMMA was stable even as the temperature rose, however, carbon/glass/PMMA exhibited better performance compared with carbon/glass/epoxy with an increase in impact energy response estimated at 50% (25 °C) and 53% (80 °C). Also, the pseudo-ductile phenomenon was strongly evident, which facilitates the predictablility of failure.     

Use of block copolymer-stabilized cadmium sulfide quantum dots as novel tracers for laser scanning confocal fluorescence imaging of blend morphology in polystyrene/poly(methyl methacrylate) films

This paper describes the first use of polymer-coated quantum dots (QDs) as fluorescent tracers for LSCFM imaging of phase morphology in polymer blends. Cadmium sulfide (CdS) QDs stabilized at the surface with a PS-b-PAA block copolymer are shown to be well dispersed via their polystyrene (PS) brush layer in the PS phase of solvent-cast 40/60 (w/w) PS/PMMA blends. The QDs are excluded from the PMMA phase, providing excellent fluorescence contrast for LSCFM imaging of the phase-separated blends. The presence of PS-b-PAA-stabilized QDs does not appear to affect the blend morphology, since the observed morphologies are the same when the percentage of QDs within the PS phase is varied from 10 to 50 wt %. These QD fluorescent tracers are used to characterize several aspects of blend morphology in solvent-cast 40/60 PS/PMMA blends containing PS homopolymer with either 100 (low molecular weight) or 1250 (high molecular weight) repeat units. In the PS(1250)/PMMA blends, a percolating distribution of PMMA droplets (2-25 mum) in a PS matrix is observed in the bulk, and a distinct inversion in the continuous phase is found near the glass substrate. In the PS(100)/PMMA blends, a "phase-in-phase" morphology is found, consisting of large PS domains (20-100 mum) dispersed in a PMMA continuous phase and small PMMA domains (1-2 mum) scattered throughout the larger PS droplets. The observed change in blend structure is attributed to a lower interfacial tension for the lower molecular weight PS.     

Preparation and properties of aniline chain-extended thermoplastic epoxy resin using triphenylphosphine as catalyst

Thermoplastic resins have been widely used in fiber reinforced polymer composites because of its recyclability and short cycle times. However, the high viscosity after heating and melting restricts its infiltration on the surface of fiber. In this study, a series of thermoplastic epoxy resins were prepared via the chain extension reaction of epoxy groups with liquid aniline using triphenylphosphine (TPP) as catalyst. The relationship between polymer network structure and performance was comprehensively investigated. The solubility tests indicated that excessive aniline or TPP facilitated the crosslinking of resins. Besides, on the premise of thermoplasticity, appropriate TPP could increase the degree of chain extension, molecular weight, and glass transition temperature of resins. Furthermore, the in-situ polymerization process facilitated infiltration between epoxy resin and the fibers before chain extension reaction. The bending test showed that the flexural performance of the sample with 2 phr of TPP was improved by 38.8%. Therefore, this work provides a feasible method to prepare the thermoplastic epoxy resins and its fiber-reinforced composites with good mechanical properties.     

New strategy to reinforce and toughen composites via introducing thorns-like micro/nanofibers

In this work, we report a new strategy of introducing thorns-like fiber into composites, so that the resultant composites substantially benefit from strong fiber–matrix interface adhesion. Specifically, the “thorns” could increase in interlocking molecules chains and entangle with the surrounding matrix resin, which could impede the mobility of polymer chains, as like the roots with uplift capacity. Strong interfacial adhesion between fibers and matrices is suggested by the SEM images and the DMA studies. After the thorns-like fibers are embedded into epoxy resin, the glass transition temperature (T_g) and the storage modulus (E′) are higher than these of neat epoxy and untreated fibers-reinforced epoxy, respectively, and the flexural properties of the composites reinforced with thorns-like fibers are significantly increased. Therefore these novel three dimensional thorns-like fibers will be applicable for composite materials based upon its unique architecture, making it an attractive alternative to increase the performance of any matrix resin.     

Visualization of the morphology at the interphase of glass fibre reinforced epoxy-thermoplastic polymer composites

This work deals with the effect that the use of glass fibres has on the morphology developed by a thermoplastic polymer modified epoxy. In particular, three surface modifications of the glass fibres were studied: calcinations desizing, activation with hydrochloric acid and coating with 3-aminopropyltriethoxy silane. As the epoxy polymer, a model system based on the full reaction of DGEBA and 2-methyl-1,5-diaminopentane was used. As the modifiers of the epoxy thermoset, two thermoplastic polymers were used: poly(methylmethacrylate) and polystyrene. The morphologies were examined either in the polymer bulk or at the interfaces by means of scanning electron microscopy and atomic force microscopy. After a thoroughly examination of the samples it was found that the thermoplastic polymers preferentially accumulate at the interfaces of these materials when activated and silanized glass fibres are used. These results might be attributed to a gradual phase separation process due to stoichiometric gradients which, on the other hand, seems to be conditioned by the nature of glass fibres surface.     

Full color light‐emitting electrospun nanofibers prepared from PFO/MEH‐PPV/PMMA ternary blends

In this study, luminescence electrospun (ES) nanofibers based on ternary blends of poly(9,9‐dioctylfluoreny‐2,7‐diyl) (PFO)/poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV)/poly(methyl methacrylate) (PMMA) were prepared from chloroform solutions using a single capillary spinneret. Effects of PFO/MEH‐PPV ratio on the morphology and photophysical properties were studied while the PMMA weight percentage was fixed at 90 wt %. The morphologies of the prepared ES fibers were characterized by FE‐SEM and fluorescence microscopy. The obtained fibers had diameters around a few hundred nm and pore sizes in the range of 30–35 nm. The emission colors of the PFO/MEH‐PPV/PMMA blend ES fibers changed from blue, white, yellowish‐green, greenish‐yellow, orange, to yellow, as the MEH‐PPV composition increased. In contrast, the emission colors of the corresponding spin‐coated films were blue, orange, pink‐red, red, and deep‐red. Based on the values of solubility parameters, the PFO and MEH‐PPV are miscible to each other and trapped in the PMMA matrix. Hence, energy transfer between these two polymers is possible. The smaller aggregated domains in the ES fiber compared to those of spin‐coated films possibly reduce the efficiency of energy transfer, leading to different emission colors. Also, the prepared ES fibers had higher photoluminescence efficiencies than those of the spin‐coated films. Pure white light‐emitting fibers prepared from the PFO/MEH‐PPV/PMMA blend ratio of 9.5/0.5/90 had the Commission Internationale de L'Eclairage (CIE) coordinate of (0.33, 0.31). Our results showed that different color light‐emitting ES fibers were produced through optimizing the composition of semiconducting polymer in the transparent polymer matrix. This type of ES fibers could have potential applications as new light sources or sensory materials for smart textiles. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 463–470, 2009     

Approach to improving the toughness of TGMDA/DDS epoxy resin by blending with thermoplastic polymer powders

A series of hot-melt processable thermosetting compositions was prepared by blending N,N,N′,N′-tetraglycidyl-4,4′ -diaminodiphenyl-methane/4,4′-diaminodiphenylsulfone (TGMDA/DDS) epoxy resin and thermoplastic polymer powders with average particle size below 30 μm. The basic thermoplastic polymers were either a high T_g amorphous cardo polyimide (T_g=350°C) or commercial semicrystalline PA6 and PA12 polyamides. The resulting heterogeneous mixtures showed viscosity values below 5000 cps suitable for prepregging process. After cure, phase-separated morphologies were maintained with a rather limited interphase miscibility as demonstrated by thermomechanical analysis. Scanning electron microscope examination of fracture surfaces pointed out a strong adhesion between the powder particles and the surrounding polyepoxy network, particularly for the potentially reactive polyamide structures. Moreover, as shown by differential scanning calorimeter analysis, the crystallinity ratio of the PA6 and PA12 powders was lowered due to melting during thermal polymerization. The fracture toughness properties of the powder-containing materials were compared with those of a fully miscible cardo polyimide–TGMDA/DDS blend coming from an homogeneous resin composition. The best improvement in fracture energy was obtained for the powder-modified resins. The most effective composition filled with 16 wt% of powdered polyimide exhibited a fourfold increase in G_IC (388 J/m² versus 100 J/m²) without compromising the epoxy thermomechanical stability (T_g=227°C versus 223°C).     

A PMMA composite as an optical diffuser in a liquid crystal display backlighting unit (BLU)

The effect of thermo-physical properties, relative humidity and stiffness on the warpage of a poly(methyl methacrylate) (PMMA) diffusing plate modified with glass fibers in a direct-lit backlight unit (BLU) of a liquid crystal display (LCD) was investigated. The warpage of the PMMA diffusing composites modified with a glass fiber were significantly reduced relative to that of a conventional PMMA diffusing plate. Luminance and scattering characteristics of the PMMA diffusing composites having 5, 10, 20 vol% of glass fibers were measured. Although the luminance of the composite was lowered as increasing the volume fractions of glass fibers in the PMMA composites, good brightness uniformity of the composites on a light source was obtained.     

PMMA/超支化聚(酯-酰胺)共混物薄膜中柱状相结构的形成

利用相差显微镜、三维形貌测量仪对聚甲基丙烯酸甲酯 超支化聚 (酯 酰胺 ) (PMMA HBP)共混物薄膜在玻璃基板作用下的相分离行为进行了研究 .结果表明 ,不同组分比的共混物薄膜会呈现不同的相形态和相分离过程 .当薄膜厚度在 5 0 0nm左右 ,HBP为低组分时 ,发现了一种特殊的分散相为圆柱状的相形态 ,并对该相形态出现的条件进行了研究 .认为基板与组分之间的相互作用和薄膜厚度决定了圆柱状结构形成 .     

用苯乙烯-丙烯腈无规共聚物作增容剂改善聚碳酸酯/聚甲基丙烯酸甲酯相容性的研究

对聚碳酸酯（ＰＣ）／苯乙烯 丙烯腈无规共聚物（ＰＳＡＮ）／聚甲基丙烯酸甲酯（ＰＭＭＡ）三元共混物，运用平均场理论，通过二元链段相互作用参数χｉｊ计算了其中三个二元对共混组成的相互作用参数χｂｌｅｎｄ，并计算了三元共混体系的ｓｐｉｎｏｄａｌ曲线．由此预测了三元共混物相容的条件，讨论了ＰＳＡＮ组成，各聚合物分子量对体系相容性的影响，并进行了实验验证．结果表明通过适当控制共聚组成和分子量，ＰＳＡＮ可以作为ＰＣ和ＰＭＭＡ共混物的增容剂，并可以通过仅改变ＰＳＡＮ在共混物中的比例来改善体系的相容性，直至得到完全均相的三元共混物．     

反相微乳液模板原位聚合制备纳米氯化银/聚甲基丙烯酸甲酯及其结构表征

用甲基丙烯酸甲酯(MMA)作油相,反相胶束微乳液作为模板,制备了纳米氯化银(AgCl)粒子,再进行原位聚合制备了纳米氯化银/聚甲基丙烯酸甲酯(AgCl/PMMA)复合材料.透射电镜(TEM)分析表明,纳米AgCl的尺寸为20～80 nm.扫描电镜(SEM)测试表明纳米AgCl粒子均匀地存在于PMMA基材中.红外分析证明,胶束中水和表面活性剂AOT的羰基在MMA聚合后微观环境发生变化,纳米粒子同聚合物之间有吸附行为.动态力学(DMTA)分析复合材料,发现纳米AgCl粒子与聚合物之间存在强烈相互作用,形成了中间相层(interphase layer),改变了聚合物的动态力学性能.     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.     

氧化石墨烯/PMMA和表面官能化的石墨烯/PMMA复合材料的制备及其力学性能的研究

使用简单的溶液共混的方法制备了氧化石墨烯/聚甲基丙烯酸甲酯(GO/PMMA)和表面官能化的石墨烯/聚甲基丙烯酸甲酯复合材料.通过透射电镜(TEM),扫描电镜(SEM)和原子力显微镜(AFM)观察了石墨烯及复合材料的表观形貌.通过拉伸实验表征了其力学性能,研究发现随着石墨烯的加入,其拉伸强度和断裂伸长率都有所改善,而且表面官能化的石墨烯的复合材料的改善效果要优于氧化石墨烯.     

Thermal induced phase separation of E7/PMMA PDLC system

The phase behaviour of thermoplastic polymer-dispersed liquid crystal system is studied with particular emphasis on the various transitions that occur within the system. The extent of plasticization of the polymer(polymethyl methacrylate) by the low molecular weight liquid crystal(E7) along with the several transitions of theLC(Liquid Crystal) are determined by modulated DSC. Optical microscopy was used to construct the temperature versus composition phase diagram. Our study indicates the existence of a limiting temperature of 40°C around which the PMMA matrix turns glassy irrespective of the initial composition within the phase separated region, suggesting the intersection of the glass transition curve with the coexistence curve. A slight depression of theN-I(Nematic to Isotropic) transition of theLC is observed with increasing composition of PMMA whereas theS-M(Smectic to Nematic) transition and theT _g (Glass transition temperature) of theLC remain unaffected. The one phase mixture remains isotropic until phase separation at a lower temperature where theLC rich domains become nematic. The growth ofLC rich domains is studied as a function of temperature and time.     

Interdiffusion at the interface between poly(vinylpyrrolidone) and epoxy

Electron microprobe analysis (EMP) was used to study interdiffusion in bilayer films of thermoplastic poly(vinylpyrrolidone) (PVP) and a thermoset epoxy. The bilayer films were prepared by casting a stoichiometric mixture of the uncured diglycidyl ether of bisphenol A epoxy (DGEBA) and 4,4′-diaminodiphenylsulfone (DDS) on the PVP film and then curing the system in a two-step process under a nitrogen atmosphere. For the EMP studies, the sulfur signal was used as a probe for DDS, while the nitrogen signal served as a probe for both DDS and PVP. The addition of brominated DGEBA to the conventional DGEBA in a 1: 1 weight ratio allowed the bromine signal to be used as a probe for the epoxy phase. It was found that the interfacial thickness was much larger for the film prepared from low molecular weight PVP than that from high molecular weight PVP. Interdiffusion was suppressed when the initial cure temperature in the two-step cure cycle was 130°C compared to 170°C, in which the first stage of the cure reaction dominated the interdiffusion process. More importantly, it was demonstrated that the diffusion front of the curing agent was located closer to the thermoplastic polymer phase as compared to that of the thermoset polymer in the interface region. This tendency was more significant in the system with the larger interfacial thickness. These results have important consequences on interphase structures and properties. They suggest that crosslinking of the epoxy in the interphase may be suppressed because of an insufficient amount of curing agent and that the not-fully-reacted curing agent in the PVP phase may act to plasticize this phase. © 1997 John Wiley & Sons, Inc.     

Dielectric properties and molecular mobility of organic/inorganic polymer composites

Microstructure-dielectric properties relationship and molecular mobility of organic/inorganic polymer composites (OIPCs), consisting of polyurethane (PU) and sodium silicate (NaSi), were investigated in this work. Broadband dielectric relaxation spectroscopy (DRS) and thermally stimulated depolarization current (TSDC) techniques were employed. Our interest was focused on the study of the glass transition mechanism and conductivity relaxation. The influence of the molecular weight of PU and inorganic phase content on the dielectric properties of the composites was of particular interest. Glass transition temperature shifts to higher temperatures with the addition of NaSi. The overall molecular mobility was found to increase in the composites, compared to the pure PU matrix. The results are more intense for the composites based on the PU with low molecular weight.