均苯四甲酸酐修饰壳聚糖微球对Pb2+和Cd2+的吸附

用交联的壳聚糖微球 (CTS) 与均苯四甲酸酐在无水条件下反应,合成均苯四甲酸酐修饰壳聚糖微球,并用FT-IR和XPS表征产物的结构。研究它对水溶液中Pb2+和Cd2+的吸附行为。考察溶液的pH,吸附时间及Pb2+和Cd2+的初始浓度对吸附金属离子的影响。吸附等温线可以用Langmuir 方程较好的描述,当pH 5.0时,该吸附剂对Pb2+和Cd2+的最大吸附量分别为296.7mg g-1和149.9mg g-1。动力学过程用二级吸附动力学模拟具有很好的线性相关性,从而确定了吸附过程为化学吸附。采用0.2mol L-1的EDTA为解析剂,Pb2+和Cd2+分别获得92.4%和85.3%的解析率。表明该吸附剂有再生性能。应用于电镀废水中铅的处理,结果满意。     

球状壳聚糖负载噻二唑树脂的合成及其吸附性能

用苯甲醛保护胺基后,将2-氨基-5-巯基-1,3,4-噻二唑引入到大孔壳聚糖微球上,合成了亲水性的多孔球状吸附树脂(CTS-AMT)。 对比研究了CTS-AMT和母体微球(CTS)对Zn2+、Cu2+、Cd2+、Pb2+、Ag+和Hg2+的吸附性能。 结果表明,pH=5.0,T=298.15 K时,CTS-AMT树脂对上述金属离子的吸附在1.5 h内基本达到平衡,对金属离子Hg2+、Ag+和Pb2+的静态饱和吸附量分别为2.54、2.31和1.71 mmol/g。 在实验浓度范围内该树脂对Hg2+的吸附过程符合 Langmuir等温吸附模型。     

绿茶对水溶液中Pb2+和Cd2+吸附性能初步研究

研究了绿茶对溶液中Pb2 和Cd2 离子的吸附和解吸性质。考察了pH、温度、吸附时间对绿茶吸附性能的影响,得到吸附动力学曲线和吸附等温线。结果表明,茶叶在pH为4~6的弱酸性范围内对两种金属离子的吸附效果最佳,在30℃时,茶叶对Pb2 和Cd2 的饱和吸附量分别为46.66 mg/g和33.29mg/g,吸附符合Langmuir吸附等温方程,并对吸附机理进行了初步的探讨。对解吸条件研究发现,用0.1 mol/L HCl和EDTA作为解吸剂,对Pb2 和Cd2 的解吸效果较好,解吸率达80%以上,可有效回收重金属Pb2 和Cd2 。     

三乙烯四胺改性榴莲壳吸附水溶液中的Cd~(2+)、Pb~(2+)

采用三乙烯四胺改性榴莲壳,制备新型的改性榴莲壳吸附剂,研究其对Cd2+、Pb2+的吸附性能。结果表明,吸附Cd2+、Pb2+的适宜条件为:pH 6.0,吸附时间120 min。改性后榴莲壳吸附剂对Cd2+、Pb2+的吸附容量有了很大程度的提高,Cd2+、Pb2+最大吸附量分别达到39.30、53.76 mg/g。吸附过程可以很好地用准二级动力学方程描述,吸附等温线用Langmuir方程的拟合效果优于Freundlich方程。     

基于SPR技术研究壳聚糖对Pb2+的吸附动力学

采用自主构建的表面等离子共振(SPR)生物传感系统研究了壳聚糖对Pb2+的吸附动力学。通过双官能团偶联剂将壳聚糖固定在传感器芯片表面,利用壳聚糖分子中含有的大量活性基团与Pb2+配位形成金属螯合物,研究了壳聚糖对不同浓度Pb2+的吸附过程,并进行动力学分析。结果表明,壳聚糖对铅离子的吸附符合Langmuir单分子吸附理论所提出的动力学方程,为壳聚糖在处理含铅环境污染物方面提供了一种理论依据。     

交联羧甲基壳聚糖微球的制备及其对Pb2+的吸附性能

交联羧甲基壳聚糖微球的制备及其对Pb2+的吸附性能     

冠醚壳聚糖多孔微球选择性富集-石墨炉原子吸收法测定绒柄牛肝菌中的痕量铅

报道了用冠醚壳聚糖多孔微球选择性富集绒柄牛肝菌中痕量铅并用石墨炉原子吸收法测定.DB-18-crown-6-CTS多孔微球在pH5.5时,对Pb2+的富集率达到98%.吸附的Pb2+能用5 mL 2 mol/L的HCl定量洗脱,洗脱率98.1%.Pb2+被洗脱后,用石墨炉原子吸收法测定.该方法的富集倍数为100倍,检出限(3σ)为0.085μg/L,相对标准偏差小于2.8%,用于分析绒柄牛肝菌样品,回收率为94.5%～102%.     

三乙烯四胺修饰交联壳聚糖树脂的制备及其对痕量镉的吸附性能研究

以戊二醛、环氧氯丙烷为交联剂,用三乙烯四胺改性,由壳聚糖合成了一种新型的三乙烯四胺修饰交联壳聚糖微球(CRN)分离树脂,研究了不同条件下CRN对Cd2+的吸附性能。在pH6.0时,CRN能定量吸附溶液中的痕量Cd2+,其静态饱和吸附容量为31.0 mg/g。吸附在CRN上的Cd2+可用0.5 mol/L的H2SO4洗脱,用火焰原子吸收法测定洗脱液中Cd2+的含量。本法对Cd2+的检出限(3σ)为24.6 ng/mL,相对标准偏差(RSD)为2.1%(n=11,c=1.0μg/mL),加标回收率在97.3%～104.0%。该方法可用于矿渣中痕量镉的测定。     

手控注射式钛酸锶钡多孔球富集器分离富集-火焰原子吸收法测定水中铅和镉

以D311树脂为模板,采用溶胶-凝胶法制备了纳米钛酸锶钡多孔球,用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和傅立叶变换红外光谱仪(FTIR)进行了表征.考察了Pd2+和Cd2+的吸附和解脱条件.将微球装柱,制成注射式富集器,研究了此富集器对水中痕量Pd2+和Cd2+的富集性能.结果表明: 此法合成的多孔球,由钙钛矿结构的纳米钛酸锶钡组成,晶体平均粒径为21 nm,球体表面布满了不规则的纳米孔洞.当pH 4～7时,此多孔球对水中的Pd2+和Cd2+具有很强的吸附能力,静态吸附容量分别为61.9和14.8 mg/g.由多孔球装柱制成的手控注射式富集器,可成功实现对水中Pd2+和Cd2+的同时吸附.用2 mol/L HNO3洗脱后,火焰原子吸收测定.建立了手控注射式纳米钛酸锶钡富集器分离富集、FAAS法测定水中痕量Pd2+和Cd2+的新方法.此方法对Pd2+和Cd2+的检出限分别为0.099和0.0034 μg/L.用于水样中痕量Pd2+和Cd2+的富集和原子吸收测定,回收率分别为97.8%～106.5%和93.0%～100.7%.     

接枝壳聚糖对铅、镉吸附行为研究及应用

在碱性条件下,用环氧氯丙烷交联制备水不溶性交联壳聚糖(CCTS),将丙烯腈单体接枝到CCTS分子骨架上制得接枝壳聚糖(CTCA)。研究了CTCA对水中Pb2 、Cd2 的吸附富集行为和洗脱行为,用原子吸收光谱法测定。结果表明,溶液的pH值为6.0时,Pb2 、Cd2 的吸附率达94%和95%,吸附容量分别达到56.6 mg/g、47.0 mg/g。用1 mol/L HCl洗脱,Pb2 、Cd2 的解吸率均可达97%。方法的检出限为:Pb2 ,0.065μg/L;Cd2 ,0.024μg/L。对10 mg/L的Pb2 、Cd2 溶液进行分离富集和测定,其相对标准偏差为3.4%和5.2%。方法已用于天然水中Pb2 、Cd2 的分离富集和测定,其回收率:Pb2 ,94%~101.9%;Cd2 ,95.6%~108%。     

Solid-supported [2+2+2] cyclotrimerizations

The transition-metal-catalyzed [2+2+2] cyclotrimerization of a diyne and an alkyne provides a convergent route to highly-substituted aromatic rings. This reaction possesses distinct drawbacks, especially low chemo- and regioselectivities, which hamper its application in combinatorial synthesis. These problems have been solved by the development of solid-supported [2+2+2]-cycloaddition reactions. If conducted on a solid-support, this reaction enables rapid combinatorial access to diverse sets of carbo- and heterocyclic small-molecule arrays. The scope of this methodology has been investigated by examining different immobilization strategies, different diyne precursors, and a variety of functionalized alkyne reaction partners. Overall, isoindoline, phthalan, and indan libraries were assembled in good to excellent yields and with high purities.     

A photoionization study of the charge transfer reactions: Xe+ + O2 → O+2 + Xe and O+2 + Xe → Xe+ + O2

Photoionization mass spectrometer techniques have been employed to study the charge transfer reactions: Xe⁺ + O₂ → O⁺₂ + Xe and O⁺₂ + Xe → Xe⁺ + O₂. The results show the reaction of Xe⁺(²P_{$\text{3}\text{2}$}) ions with O₂ molecules is much more efficient than the reaction of Xe⁺(²P_{$\text{1}\text{2}$}) ions with O₂ molecules. The charge transfer reaction of O⁺₂ ions with Xe atoms was detected for O⁺₂ ions in the a ⁴Π_u state.     

Intracellular Ruthenium-Promoted (2+2+2) Cycloadditions

Metal-mediated intracellular reactions are becoming invaluable tools in chemical and cell biology, and hold promise for strongly impacting the field of biomedicine. Most of the reactions reported so far involve either uncaging or redox processes. Demonstrated here for the first time is the viability of performing multicomponent alkyne cycloaromatizations inside live mammalian cells using ruthenium catalysts. Both fully intramolecular and intermolecular cycloadditions of diynes with alkynes are feasible, the latter providing an intracellular synthesis of appealing anthraquinones. The power of the approach is further demonstrated by generating anthraquinone AIEgens (AIE=aggregation induced emission) that otherwise do not go inside cells, and by modifying the intracellular distribution of the products by simply varying the type of ruthenium complex.     

Alkenes in [2+2+2] Cycloadditions

Participation of alkenes and allenes in [2+2+2] cycloaddition reactions has attracted much attention recently. This version of the well‐established alkyne cyclotrimerization renders interesting products, such as cyclohexadienes and other polycycles, through cascade processes. Many mechanistic variations are observed when using certain metal complexes as catalysts. The frequent generation of stereogenic centers has prompted the development of efficient asymmetric versions. This Minireview summarizes the efforts reported to date on the use of double bonds as partners in [2+2+2] cyclotrimerizations.     

Formal [(2+2)+2] and [(2+2)+(2+2)] nonconjugated dienediyne cascade cycloadditions

[reaction: see text] Fluoranthene 2 and heptacycle 3 are easily accessible from the reaction of diyne 1 and norbornadiene (NBD) in the presence of the rhodium catalyst. The unusual [(2+2)+(2+2)] adduct 3 was confirmed by the X-ray crystal structure analysis.     

Studies on Synthetic Inorganic Ion Exchangers-III Quantitative Separations of Mg2+ -Pb2+, Zn2+ - Pb2+ Cu2+ - Pb2+, Al3+ - Pb2+, Zn2+ - Cd2+, and Mg2+ - Cd2+ on Lead Antimonate Columns

Abstract

A new inorganic ion exchanger, lead antimonate has been synthesized having an Pb:Sb ratio of 1:5 and cation exchange capacity of 1.46 mequiv./g. It is fairly stable in water and dilute solutions of acids, bases and salts. Ion distribution studies on twenty metal ions have been determined on this gel at pH 1,2,3 and 5. The following mixtures have been separated: Mg²⁺ - Pb²⁺, Zn²⁺ - Pb²⁺, Zn²⁺ - Pb²⁺, Cu²⁺ - Pb²⁺, Al³⁺ - Pb²⁺, Zn²⁺ - Cd²⁺ and Mg²⁺ - Cd²⁺. Mg²⁺ and Al³⁺ were removed with 0.4 M ammonium nitrate, Cu²⁺ and Zn²⁺ with 0.4 M ammonium nitrate + 0.1M nitric acid (1:1), Pb²⁺ with 0.5M nitric acid and Cd²⁺ with 0.25M nitric acid. A tentative structure of this material is proposed on the basis of chemical analysis, pH titrations, thermogravimetry and IR spectrophotometry.     

Tethered 2 + 2 + 2 cycloaddition reactions of cobalt-cycloheptyne complexes

Cycloheptyne-dicobalt hexacarbonyl complexes, substituted by propargylic ether functions, undergo 2 + 2 + 2 cycloaddition reactions with alkynes to give tricyclic benzocycloheptanes; an all-intramolecular version of this transformation is also possible.     

Triptycenediols by rhodium-catalyzed [2+2+2] cycloaddition

An efficient, modular synthesis of triptycene derivatives is presented, in which the triptycene ring system is constructed from readily available anthraquinone and alkyne starting materials. A rhodium-catalyzed alkyne cyclotrimerization reaction serves as the key step in this new method for the preparation of these useful unnatural products.