Wettability and antifouling behavior on the surfaces of superhydrophilic polymer brushes

The surface wettabilities of polymer brushes with hydrophobic and hydrophilic functional groups were discussed on the basis of conventional static and dynamic contact angle measurements of water and hexadecane in air and captive bubble measurements in water. Various types of high-density polymer brushes with nonionic and ionic functional groups were prepared on a silicon wafer by surface-initiated atom-transfer radical polymerization. The surface free energies of the brushes were estimated by Owens-Wendt equation using the contact angles of various probe liquids with different polarities. The decrease in the water contact angle corresponded to the polarity of fluoroalkyl, hydroxy, ethylene oxide, amino, carboxylic acid, ammonium salt, sulfonate, carboxybetaine, sulfobetaine, and phosphobetaine functional groups. The poly(2-perfluorooctylethyl acrylate) brush had a low surface free energy of approximately 8.7 mN/m, but the polyelectrolyte brushes revealed much higher surface free energies of 70-74 mN/m, close to the value for water. Polyelectrolyte brushes repelled both air bubbles and hexadecane in water. Even when the silicone oil was spread on the polyelectrolyte brush surfaces in air, once they were immersed in water, the oil quickly rolled up and detached from the brush surface. The oil detachment behavior observed on the superhydrophilic polyelectrolyte brush in water was explained by the low adhesion force between the brush and the oil, which could contribute to its excellent antifouling and self-cleaning properties.     

Perfluorocarbon thin films and polymer brushes on stainless steel 316 L for the control of interfacial properties

Perfluorocarbon thin films and polymer brushes were formed on stainless steel 316 L (SS316L) to control the surface properties of the metal oxide. Substrates modified with the films were characterized using diffuse reflectance infrared Fourier transform spectroscopy (DRIFT), contact angle analysis, atomic force microscopy (AFM), and cyclic voltammetry (CV). Perfluorooctadecanoic acid (PFOA) was used to form thin films by self-assembly on the surface of SS316L. Polypentafluorostyrene (PFS) polymer brushes were formed by surface-initiated polymerization using SAMs of 16-phosphonohexadecanoic acid (COOH-PA) as the base. PFOA and PFS were effective in significantly reducing the surface energy and thus the interfacial wetting properties of SS316L. The SS316L control exhibited a surface energy of 38 mN/m compared to PFOA and PFS modifications, which had surface energies of 22 and 24 mN/m, respectively. PFOA thin films were more effective in reducing the surface energy of the SS316L compared to PFS polymer brushes. This is attributed to the ordered PFOA film presenting aligned CF(3) terminal groups. However, PFS polymer brushes were more effective in providing corrosion protection. These low-energy surfaces could be used to provide a hydrophobic barrier that inhibits the corrosion of the SS316L metal oxide surface.     

Synthesis of copolymer brushes endowed with adhesion to stainless steel surfaces and antibacterial properties by controlled nitroxide-mediated radical polymerization

Novel copolymer brushes have been synthesized by a two-step "grafting from" method that consists of the electrografting of poly(2-phenyl-2-(2,2,6,6-tetramethyl-piperidin-1-yloxy)-ethylacrylate) onto stainless steel, followed by the nitroxide-mediated radical polymerization of 2-(dimethylamino ethyl)acrylate and styrene or n-butyl acrylate, initiated from the electrografted polyacrylate chains. The grafted copolymers were quaternized in order to endow them with antibacterial properties. Peeling tests have confirmed the strong adhesion of the grafted copolymer onto the stainless steel substrate. Quartz crystal microbalance experiments have proven that fibrinogen adhesion is lower on the hydrophilic quaternized films compared to the nonionic counterpart. Such quaternized copolymers exhibit significant antibacterial activity against the Gram-positive bacteria S. aureus and the Gram-negative bacteria E. coli.     

Electrochemical procedure for constructing poly(phenylene sulfide) brushes on glassy carbon and stainless steel

A simple electrochemical approach based on potential sweeping has been developed for growing poly(phenylene sulfide) (PPS) brushes from 4,4’‐disulfanediyldibenzenediazonium salt on glassy carbon and stainless steel. First, the diazonium salt becomes reduced at the substrate on the initial part of the sweep carried out in a negative direction to form a covalently bonded diphenyl disulfide film. Once sufficiently extreme potentials are reached the disulfide bridges are reductively cleaved to form a thin layer of covalently attached thiophenolates. These are prone to be involved in fast coupling reactions with the diazonium salt to form PPS brushes in a repetitive growth process. In this manner linear PPS brushes with thicknesses up to 150 nm are easily formed. In addition, exact control on the brush length may be exerted through the switching potential selected or the number of sweeps applied. The films are characterized by time‐of‐flight secondary ion mass spectrometry which shows that the film growth is accompanied by an increase in the intensity ratio of S^?/ in line with the proposed PPS structure. This structure was further supported by Raman spectra, exhibiting a high‐intensity C?S stretch band and no S?S stretch band. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 91–98     

Comparison of antibacterial ability of copper and stainless steel

In this paper, the electro-analysis and spectrophotometric analysis methods were used to study the antibacterial ability of copper and stainless steel materials. When Escherichia coli (E. coli) and photo-bacteria were used as samples, the antibacterial effect of stainless steel was very weak, while the percentage of bacteria dying from exposure to metallic copper for 30 min was over 90%. The antibacterial ability of copper has a potential application in the field of disinfection, food packaging and piping of drinking water. Translated form Huaxue Tongbao, 2006, 69(10): 772–776 (in Chinese)     

Spectral collocation methods for polymer brushes

We provide an in-depth study of pseudo-spectral numerical methods associated with modeling the self-assembly of molten mixed polymer brushes in the framework of self-consistent field theory (SCFT). SCFT of molten polymer brushes has proved numerically challenging in the past because of sharp features that arise in the self-consistent pressure field at the grafting surface due to the chain end tethering constraint. We show that this pressure anomaly can be reduced by smearing the grafting points over a narrow zone normal to the surface in an incompressible model, and/or by switching to a compressible model for the molten brush. In both cases, we use results obtained from a source (delta function) distribution of grafting points as a reference. At the grafting surface, we consider both Neumann and Dirichlet conditions, where the latter is paired with a masking method to mimic a confining surface. When only the density profiles and relative free energies of two comparison phases are of interest, either source or smeared distributions of grafting points can be used, but a smeared distribution of grafting points exhibits faster convergence with respect to the number of chain contour steps. Absolute free energies converge only within the smeared model. In addition, when a sine basis is used with the masking method and a smeared distribution, fewer iterations are necessary to converge the SCFT fields for the compressible model. The numerical methods described here and investigated in one-dimension will provide an enabling platform for computationally more demanding three-dimensional SCFT studies of a broad range of mixed polymer brush systems.     

Simple model for grafted polymer brushes

The first theories of grafted polymer brushes assumed a step profile for the monomer density. Later, the real density profile was obtained from Monte Carlo or molecular dynamics simulations and calculated numerically using a self-consistent field theory. The analytical approximations of the solutions of the self-consistent field equations provided a parabolic dependence of the self-consistent field, which in turn led to a parabolic distribution for the monomer density in neutral brushes. As shown by numerical simulations, this model is not accurate for dense polymer brushes, with highly stretched polymers. In addition, the scaling laws obtained from the analytical approximations of the self-consistent field theory are identical to those derived from the earlier step-profile-approximation and predict a vanishing thickness of the brush at low graft densities, and a thickness exceeding the length of the polymer chains at high graft densities. Here a simple model is suggested to calculate the monomer density and the interaction between surfaces with grafted polymer brushes, based on an approximate calculation of the partition function of the polymer chains. The present model can be employed for both good and poor solvents, is compatible with a parabolic-like profile at moderate graft densities, and leads to an almost steplike density for highly stretched brushes. While the thickness of the brush depends strongly on solvent quality, it is a continuous function in the vicinity of the temperature. In good and moderately poor solvents, the interactions between surfaces with grafted polymer brushes are always repulsive, whereas in poor solvents the interactions are repulsive at small separations and become attractive at intermediate separation distances, in agreement with experiment. At large separations, a very weak repulsion is predicted.     

Protective properties of redox polymer film deposited on stainless steel

We propose a novel composite organic-inorganic coating in the form of a redox polymer film for protection of stainless steel against general corrosion in strong acid medium (2 M H₂SO₄). We utilize an anion exchange polymer, protonated poly(4-vinylpyridine), into which hexacyanoferrate anions have been introduced. Owing to the presence of Fe(CN)₆^3–/4– at the interface formed by the film and the steel, a sparingly soluble metal hexacyanoferrate (mostly Prussian blue, PB) is formed as an overcoating on the steels surface, presumably on the passive (metal oxide) layer. The redox polymer film on the steel seems to act as a composite three-dimensional bilayer-type coating in which hexacyanoferrate(III,II) anions (that are capable of effective charge storage) exist in the outer portions of the film, whereas the inner PB layer improves the systems overall adherence and stability. By analogy to a conducting polymer (e.g. polyaniline, polypyrrole), introduction of the redox polymer composite film leads to stabilization of the steel substrates potential within the passive range.Contribution to the 3rd Baltic Conference on Electrochemistry, Gdansk-Sobieszewo, Poland, 23–26 April 2003Dedicated to the memory of Harry B. Mark, Jr. (28 February 1934–3 March 2003)     

Responsive and patterned polymer brushes

While polymer brush systems continue to grow in popularity, so does their complexity and sophistication. Advances in polymerization and specific functionalization methods have led to novel applications in diverse research fields. The marriage of top‐down lithography with bottom‐up brush processing is becoming increasingly important in the development and progress of nanotechnology. The aim of this review is to examine different approaches taken to generate tailored polymer brush systems through surface‐initiated polymerizations as well as patterning techniques. Detaching polymer brushes to create free‐standing membranes is also highlighted and discussed in terms of methods and characterization. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1457–1472     

Functional polymer thin films designed for antifouling materials and biosensors

Polymer thin films offer a versatile and ubiquitous platform for a wide variety of real-world applications in biomedicine, nanotechnology, catalysis, photovoltaic devices, and energy conversion and storage. Depending on the chemical composition of the polymers and the associated microenvironment, the physicochemical properties (biocompatibility, stability, wettability, adhesion, morphology, surface free energy, and others) of polymer films can be tuned for a specific application through precisely controlled surface synthesis and the incorporation of desirable and responsive functional groups. In this short review, we first summarise the methods most commonly used for the fabrication of polymer thin films. Then we discuss how these polymer thin films can be used in a selection of biomedical applications in antifouling materials and biosensors. Some directions for the rational design of polymer thin films to achieve a specific function or application are also provided.     

Interfacial friction and adhesion of polymer brushes

A bead-probe lateral force microscopy (LFM) technique is used to characterize the interfacial friction and adhesion properties of polymer brushes. Our measurements attempt to relate the physical structure and chemical characteristics of the brush to their properties as thin-film, tethered lubricants. Brushes are synthesized at several chain lengths and surface coverages from polymer chains of polydimethylsiloxane (PDMS), polystyrene (PS), and a poly(propylene glycol)-poly(ethylene glycol) block copolymer (PPG/PEG). At high surface coverage, PDMS brushes manifest friction coefficients (COFs) that are among the lowest recorded for a dry lubricant film (μ ≈ 0.0024) and close to 1 order of magnitude lower than the COF of a bare silicon surface. Brushes synthesized from higher molar mass chains exhibit higher friction forces than those created using lower molar mass polymers. Increased grafting density of chains in the brush significantly reduces the COF by creating a uniform surface of stretched chains with a decreased surface viscosity. Brushes with lower surface tension and interfacial shear stresses manifest the lowest COF. In particular, PDMS chains exhibit COFs lower than PS by a factor of 3.7 and lower than PPG/PEG by a factor of 4.7. A scaling analysis conducted on the surface coverage (σ) in relation to the fraction (ε) of the friction force developing from adhesion predicts a universal relation ε ~ σ(4/3), which is supported by our experimental data.     

Combination of electrografting and atom-transfer radical polymerization for making the stainless steel surface antibacterial and protein antiadhesive

A two-step "grafting from" method has been successfully carried out, which is based on the electrografting of polyacrylate chains containing an initiator for the atom transfer radical polymerization (ATRP) of 2-(tert-butylamino)ethyl methacrylate (TBAEMA) or copolymerization of TBAEMA with either monomethyl ether of poly(ethylene oxide) methacrylate (PEOMA) or acrylic acid (AA) or styrene. The chemisorption of this type of polymer brushes onto stainless steel surfaces has potential in orthopaedic surgery. These films have been characterized by ATR-FTIR, Raman spectroscopy, atomic force microscopy (AFM), and measurement of contact angles of water. The polymer formed in solution by ATRP and that one detached on purpose from the surface have been analyzed by size exclusion chromathography (SEC) and (1)H NMR spectroscopy. The strong adherence of the films onto stainless steel has been assessed by peeling tests. AFM analysis has shown that addition of hydrophilic comonomers to the grafted chains decreases the surface roughness. According to dynamic quartz crystal microbalance experiments, proteins (e.g., fibrinogen) are more effectively repelled whenever copolymer brushes contain neutral hydrophilic (PEOMA) co-units rather than negatively charged groups (PAA salt). Moreover, a 2- to 3-fold decrease in the fibrinogen adsorption is observed when TBAEMA is copolymerized with either PEOMA or AA rather than homopolymerized or copolymerized with styrene. Compared to the bare stainless steel surface, brushes of polyTBAEMA, poly(TBAEMA-co-PEOMA) and poly(TBAEMA-co-AA) decrease the bacteria adhesion by 3 to 4 orders of magnitude as revealed by Gram-positive bacteria S. aureus adhesion tests.     

A modified polyvinylchloride surface with antibacterial and antifouling functions

Surfaces with antibacterial and hydrophilic properties are very attractive to cardiovascular applications. The objective of this study was to synthesize and immobilize a novel antibacterial and hydrophilic polymer onto surface of polyvinylchloride via an effective and mild surface coating technique. The surface coated with a terpolymer constructed with N‐vinylpyrrolidone, 3,4‐dichloro‐5‐hydroxy‐2(5H)‐furanone derivative, and succinimide residue was evaluated with cell adhesion, bacterial adhesion, and bacterial viability. 3T3 mouse fibroblast cells and two bacteria species were used to evaluate surface adhesion and antibacterial activity. Results showed that the polymer‐modified polyvinylchloride surface exhibited not only significantly decreased 3T3 fibroblast cell adhesion with a 66% to 87% reduction but also significantly decreased bacterial adhesion with 69% to 87% and 52% to 74% reduction of Pseudomonas aeruginosa and Staphylococcus aureus attachment, respectively, as compared with original polyvinylchloride. Furthermore, the modified polyvinylchloride surfaces exhibited significant antibacterial functions by inhibiting bacterial growth (75%‐84% and 78–94% inhibition of P aeruginosa and S aureus, respectively, as compared to original polyvinylchloride) and killing bacteria. These results demonstrate that covalent polymer attachment conferred antifouling and antibacterial properties to the polyvinylchloride surface.     

Symmetric pH-dependent swelling and antibacterial properties of chitosan brushes

Charged polymer brushes grafted to surfaces are of great interest for antibacterial, biosensor, nanofluidic, and drug delivery applications. In this paper, chitosans with quaternary ammonium salts, CH-Q, were immobilized on silicon oxide and characterized by in situ quartz-crystal microbalance with dissipation, QCM-D, and in situ spectroscopic ellipsometry, SE. Both methods showed that the hydrated film exhibited a minimum thickness of ~40 nm near pH 5 that increased strongly (up to ~80 nm) at lower and higher pH. This symmetric swelling is surprising because CH-Q is a cationic polymer. The CH-Q grafted layer was stable for pH values from 3 to 8 and exhibited rapid, reversible swelling and contraction upon varying pH. The CH-Q layer also reduced S. aureus colonization by a factor of ~30× compared to bare silicon oxide and an amine terminated silane grafted to silicon oxide. This antibacterial characteristic of CH-Q is attributed to the quaternary ammonium salts and the flexible polymer brush.     

Molecularly imprinted polymer coated on stainless steel fiber for solid-phase microextraction of chloroacetanilide herbicides in soybean and corn

A molecularly imprinted polymer (MIP) with metolachlor as template was firstly coated on stainless steel fiber through chemical bonding strategy to solve the fragility problem of silica fiber substrate for solid-phase microextraction. The surface pretreatment of stainless steel fiber and the polymerization conditions were investigated systematically to enhance the preparation feasibility and MIP coating performance, and then a porous and highly cross-linked MIP coating with 14.8-μm thickness was obtained with over 200 times re-usability which was supported by non-fragile stainless steel fiber adoption. The MIP coating possessed specific selectivities to metolachlor, its metabolites and other chloroacetanilide herbicides with the factors of 1.1–4.6. Good extraction capacities of metolachlor, propisochlor and butachlor were found with MIP coating under quick adsorption and desorption kinetics, and the detection limits of 3.0, 9.6 and 38 μg L⁻¹ were achieved, respectively. Moreover, the MIP-coated stainless steel fiber was evaluated for trace metolachlor, propisochlor and butachlor extraction in the spiked soybean and corn samples, and the enrichment factors of 54–60, 27–31 and 15–20 were obtained, respectively.     

Development of a novel antifouling platform for biosensing probe immobilization from methacryloyloxyethyl phosphorylcholine-containing copolymer brushes

The immobilization of thiol-terminated poly[(methacrylic acid)-ran-(2-methacryloyloxyethyl phosphorylcholine)] (PMAMPC-SH) brushes on gold-coated surface plasmon resonance (SPR) chips was performed using the "grafting to" approach via self-assembly formation. The copolymer brushes provide both functionalizability and antifouling characteristics, desirable features mandatorily required for the development of an effective platform for probe immobilization in biosensing applications. The carboxyl groups from the methacrylic acid (MA) units were employed for attaching active biomolecules that can act as sensing probes for biospecific detection of target molecules, whereas the 2-methacryloyloxyethyl phosphorylcholine (MPC) units were introduced to suppress unwanted nonspecific adsorption. The detection efficiency of the biotin-immobilized PMAMPC brushes with the target molecule, avidin (AVD), was evaluated in blood plasma in comparison with the conventional 2D monolayer of 11-mercaptoundecanoic acid (MUA) and homopolymer brushes of poly(methacrylic acid) (PMA) also immobilized with biotin using the SPR technique. Copolymer brushes with 79 mol % MPC composition and a molecular weight of 49.3 kDa yielded the platform for probe immobilization with the best performance considering its high S/N ratio as compared with platforms based on MUA and PMA brushes. In addition, the detection limit for detecting AVD in blood plasma solution was found to be 1.5 nM (equivalent to 100 ng/mL). The results have demonstrated the potential for using these newly developed surface-attached PMAMPC brushes for probe immobilization and subsequent detection of designated target molecules in complex matrices such as blood plasma and clinical samples.     

Neutral and charged polymer brushes at solid surfaces

Neutral and charged polymer brushes covalently attached to planar solid surfaces were generated by using self-assembled monolayers of an azo initiator and radical chain polymerization in situ. The brushes were characterized by FTIR-spectroscopy, optical waveguide-spectroscopy and Ellipsometry. Especially the film thicknesses of surface bound polyelectrolyte (PEL) monolayers were measured by optical waveguide spectroscopy (OWS) as a function of the humidity of the environment. The PEL brushes show strong increases in thickness as well as strong decrease of the refractive index of the surface attached layer due to water incorporation caused by the exposure to the humid environment. Additionally the behavior of neutral as well as charged brushes in contact with solvent was investigated by using multiple-angular-scans of ellipsometry in a total internal reflectance setup. The scaling behavior of the brush height as a function of the graft density of the attached polymer molecules was investigated for the neutral brush as well as for the PEL brush system.     

Liquid-crystalline polymer brushes: deformation and microphase segregation

A statistical theory of the structure and thermodynamics of a planar brush (‘accordion’) formed by bridged polymer chains containing mesogenic segments and immersed in a solvent is developed. It is shown that deformation of an accordion can lead to the formation of a two-phase structure with coexisting liquid-crystalline (LC) and swollen microphases. Phase diagrams for accordions with different grafting densities are obtained. The influence of anisotropic interaction between mesogenic segments on the structure of phase diagrams is investigated.     

仿生聚合物材料用于糖肽的高选择性富集

蛋白质糖基化分析对深入认识其生物功能和发现生物标志物意义重大。由于生物样品中糖肽的丰度低，糖肽的富集至关重要。该文合成了一种以色氨酸为功能基团的新型仿生聚合物材料（简称Poly-Trp），并用于糖肽的高选择性富集。扫描电子显微镜、热分析仪和红外光谱仪等表征证明Poly-Trp已成功合成。通过考察溶液条件变化对糖肽在Poly-Trp保留的影响，发现糖肽在Poly-Trp上的保留分别随着溶液中乙腈浓度的降低和酸度的升高而变弱。且Poly-Trp对牛胎球蛋白糖肽的富集选择性高于商品化ZIC-HILIC和氨基硅胶，能抵抗物质的量倍数为100的牛血清白蛋白的干扰。该研究中仿生聚合物材料的设计为糖肽富集材料提供了新思路和新方法。     

Homeotropic and planar structures in liquid-crystalline polymer brushes

The ordering in polymer brushes formed by macromolecules with mesogenic groups in the main chain is investigated. The numerical method of self-consistent field approximation was used. The existence of two different liquid crystalline nematic states is shown: homeotropic (HLC) and planar (PLC) states. The free energy of the HLC state is always less than that of the PLC state. However, with the increase of energy of anisotropic interactions, (with decrease in temperature) our numerical procedure leads us to either one or another state depending on the grafting density. The results obtained show that both brush surfaces, play an essential role in establishing the concrete LC state structure. The grafting surface and the external surface force the planar order.