Arsenic speciation by coupling capillary zone electrophoresis with mass spectrometry

Summary Capillary zone electrophoresis (CZE) has been coupled with mass spectrometry to enable the identification of mineral and organometallic compounds of arsenic in speciation studies. The electrophoretic effluent was introduced through a concentric interface into the mass spectrometer. Make-up liquid was added to enable electric contact at the outlet of the separation capillary and to assist the electronebulization process. After ionization, the ions were analyzed and quantified with an ion-trap detector. Optimization of the coupling conditions (geometry of the concentric interface, composition and flow rate of the sheath liquid, electronebulization and detection conditions) is described. The results show that the geometry of the concentric interface and the positioning of the outlet of the separation capillary have a critical effect on stability and sensitivity. Programming the electronebulization and detection conditions throughout the analysis enabled identification and quantification of the seven arsenic compounds of interest (neutral, and positively or negatively charged species) in less than 20 min at the ppm level. Limits of detection ranged from 0.5 to 3.3 mg L⁻¹, corresponding to amounts injected ranging from 15 to 60 pg. The linear dependence of mass spectrometric response on arsenic concentration was verified for concentrations ranging from 5 to 200 mgL⁻¹. For the two positively charged species, arsenobetaine and arsenocholine, an on-line preconcentration technique (field-amplified sample injection) enabled reduction of the detection limits by approximately one order of magnitude to 110 and 160 μgL⁻¹, respectively.     

Development of a fully buffered molybdate electrolyte for capillary electrophoresis with indirect detection and its use for analysis of anions in Bayer liquor

A new counterion-buffered molybdate electrolyte was developed and optimized for simultaneous quantitative determination of up to eight anions (chloride, sulphate, oxalate, fluoride, formate, malonate, succinate, and acetate) in Bayer liquor by capillary electrophoresis with indirect detection at 214 nm. The separation parameters were optimized in respect to separation of the critical analyte group fluoride-formate-malonate, with the optimal electrolyte prepared from molybdic trioxide containing 5.0 mmol/L MoO3, 1.3 mmol/L cetyltrimethylammonium bromide (CTAB), and buffered with diethanolamine (DEA) to pH 9.2 (ca. 20 mM DEA). Total length of separation capillary was 80 cm, resulting in run time of under 4 min. The method is suitable for a wide concentration range of the analytes (1-50 mg/L) with linear calibration plots (R2 = 0.9983-0.9999). Relative standard deviations were 0.05%-0.07% for migration times and 0.67%-2.04% for peak areas. The detection limits were in the range of 0.17-0.51 mg/L or 2-10 micromol/L (hydrostatic injection of 30 s of 1000 x diluted sample). Due to its good buffering capacity, the electrolyte exhibited an excellent ruggedness and good tolerance to the alkaline samples. Consequently, Bayer liquor samples could be diluted as little as 100 x which allows more sensitive determination of minor components over previous methods. The method was successfully applied to analysis of Bayer liquor samples with recoveries in the range of 95-105%.     

Hydrodynamic suppression of the electroosmotic flow in capillary electrophoresis with indirect spectrophotometric detection

A version of capillary electrophoresis with indirect spectrophotometric detection and the hydrodynamic suppression of electroosmotic flow is studied. It is shown that, to improve the reliability of ion identification, one should calculate electrophoretic mobilities of ions or migration times corrected with regard to the electroosmotic flow rate. Correlations between electrophoretic peak areas of ions and their electrophoretic mobilities are derived. In the studied version of capillary electrophoresis, the accuracy of measuring anion concentrations can be improved using the internal standard method.     

Hyphenation of capillary electrophoresis to inductively coupled plasma mass spectrometry as an element-specific detection method for metal speciation

A stepwise development for the use of capillary electrophoresis and inductively coupled plasma mass spectrometry (ICP-MS) for speciation investigations is presented. The high resolution power of CE is used for the separation of metal species, whereas ICP-MS is taken for element-specific detection with low detection limits. This contribution starts with an off-line combination of both instruments. Separation and identification of species in model solutions and real samples are shown by scanning UV detection at the CE unit with subsequent metal quantification in peak related fractions, applying electrothermal vaporization ICP-MS. Finally, first separations are demonstrated, using the on-line hyphenation with a laboratory-made nebulizer. Here, standard solutions are separated and monitored by UV and ICP-MS. Stability of electrical current during nebulization was checked and a possibly interfering suction flow was estimated. After optimization sufficient electropherograms were obtained. Advantages and problems are discussed for both modes.     

Separation of phospholipids by capillary zone electrophoresis with indirect ultraviolet detection

A simple method for separation of different anionic and zwitterionic phospholipid classes by capillary zone electrophoresis (CZE), using indirect UV detection with adenosine monophosphate (AMP) as background electrolyte and the UV-absorbing additive, was successfully developed in this study. The separation conditions including apparent pH (pH*) of running buffer, concentration of AMP, organic solvent, applied voltage and capillary temperature were systematically optimized. The application of this method to human blood sample was also briefly examined.     

The speciation of rhodium(III) in hydrochloric acid media by capillary zone electrophoresis

A fast and effective method to study the aquation of rhodium(III) chlorocomplex in hydrochloric solutions using capillary zone electrophoresis (CZE) is developed. At least five species, some of which seem to be oligomeric, are formed in solution during the aquation process at pH>1. The fast hydration of RhCl₆³⁻ makes this species impossible to detect. The first species detected in the optimised conditions is RhCl₅(H₂O)²⁻ although RhCl₄(H₂O)₂⁻ is the main species during the first stage of the aquation process. When equilibrium is reached either RhCl₃(H₂O)₃ or a cationic complex, RhCl₂(H₂O)₄⁺, is formed as the main species. Matrix Assisted Laser Desorption Ionisation Time of Flight Mass Spectrometry (MALDI-TOF MS) is used as a novel technique to elucidate the structure of the rhodium aqua/chloro complexes formed in solution. Results obtained by CZE are confirmed by spectrophotometry.     

Separation of phenolic acids by capillary electrophoresis with indirect contactless conductometric detection

A new method for the electrophoretic separation of nine phenolic acids (derivatives of benzoic and cinnamic acids) with contactless conductometric detection is presented. Based on theoretical calculations, in which the mobility of the electrolyte co- and counterions and mobility of analytes are taken into consideration, the electrolyte composition and detection mode was selected. This approach was found to be especially valuable for optimization of the electrolyte composition for the separation of analytes having medium mobility. Indirect conductometric detection mode was superior to the direct mode as predicted theoretically. The best performance was achieved with 150 mM 2-amino-2-methylpropanol electrolyte at pH 11.6. The separation was carried out in a counter-electroosmotic mode and completed in less than 6 min. The LODs achieved were about 2.3-3.3 microM and could be further improved to 0.12-0.17 microM by using a sample stacking procedure. The method compares well to the UV-Vis detection.     

Optimization of cation detection by capillary zone electrophoresis with indirect UV absorbance

Summary The indirect UV detection of cations by capillary zone electrophoresis gives peaks of very different height or area between cations. We show that the height depends on the electrophoretic mobility of the cation compared with the electrophoretic mobility of the chromophore used. Moreover, the limit of detection can be easily improved by about 4-fold by adjusting the concentration of complexing agent or by using a chromophore with the same velocity as the studied cation. Using a new parameter termedsensitization power we can optimize the limit of detection and have determined the best chromophores for each family of cations.Sensitization power is a maximum for: alkali metals and alkali earths with imidazole and UV Cat 2^?, for transition metal with pyridine, for light rare earth with ephedrine and UV Cat 1^?, for heavy lanthanides with 1-naphthylamine and phenyl-trimethyl-ammonium bromide. Corrected areas of all cations studied have normal distributions directly proportional to their ionic charge. Certain behaviour can be predicted for elements such as actinides. Detection can also be enhanced because the relation of proportionality between ionic charge and corrected area allows comparison of the performance of all chromophores.     

Determination of quinine in beverages by online coupling capillary isotachophoresis to capillary zone electrophoresis with UV spectrophotometric detection

The present study illustrates the possibilities of capillary isotachophoresis (CITP) online coupled with capillary zone electrophoresis (CZE) and hyphenated with fiber-based spectrophotometric diode array detection (DAD) for the direct, highly reliable, and ultrasensitive determination of quinine (QUI) in real multicomponent ionic matrices (beverages). Here, the CITP provided an effective online sample pretreatment (preseparation and preconcentration) prior to the CZE separation. Due to the CITP sample preconcentration, a simple UV-visible absorbance spectrophotometric detection was sufficient for obtaining very low concentration limits of detection (~2.3 ng/mL). Enhanced separation selectivity due to the combination of different separation mechanisms (CITP vs. CZE) enabled to obtain a pure analyte zone, suitable for its detection and quantitation in the directly injected real samples. The spectrophotometric DAD, unlike single wavelength UV detection, enabled to characterize the purity (i.e. spectral homogeneity) of the analyte zone and preliminary data indicate structurally related compounds via characteristic spectra recorded in the interval of 200-600 nm. The proposed CITP-CZE-DAD method was characterized by favorable performance parameters (sensitivity, linearity, precision, recovery, accuracy, robustness, and selectivity) and successfully applied to the control of QUI and potential QUI impurities in commercial beverages. This method is proposed as a routine automatized method for the highly reliable quality food control.     

Isoelectric buffers, part 3: determination of pKa and pI values of diamino sulfate carrier ampholytes by indirect UV-detection capillary electrophoresis

Ampholytes with close pK(a) values (i.e., good carrier ampholytes (CAs)) are needed as buffers in pH-biased isoelectric trapping (IET) separations. The syntheses of two families of such good CAs were reported recently. Members of the family of diamino sulfate ampholytes (first series) had pI values in the 5.7 < pI < 9.0 range. Members of the family of quaternary ammonium dicarboxylic acid ampholytes (second series) had pI values in the pI < 4.3 range. To further characterize the diamino sulfate ampholytes, their effective mobilities were measured by indirect UV-absorbance detection capillary electrophoresis in a series of background electrolytes (BGEs) with different pH values. The pK(a) and limiting ionic mobility values of the CAs were obtained by fitting these mobility values, as a function of the pH and the ionic strength of the BGEs, to the theoretical mobility expression. These diamino sulfates complete the list of CAs suitable for IET separations.     

Determination of mannitol and sorbitol in infusion solutions by capillary zone electrophoresis using on-column complexation with borate and indirect spectrophotometric detection

Capillary zone electrophoresis with indirect UV detection at 215 nm was applied for the separation and determination of mannitol (MA), sorbitol (SO) and xylitol in the form of anionic borate-polyol complexes. The separation was carried out in a fused silica capillary (total length 60 cm, effective length 50 cm, I.D. 50 microm) at 25 kV. The optimized background electrolyte was 200 mM borate buffer (pH 9.3, adjusted with triethylamine) containing 10 mM 3-nitrobenzoate as the chromogenic co-ion. The separation took approximately 13 min. The rectilinear calibration range was 0.2-2 mg mL(-1) for MA and SO when using xylitol (1 mg mL(-1)) as the internal standard. The limit of detection at a S/N of 3 was approximately 30 microg mL(-1) for either analyte. The method was used for the assay of MA or SO in pharmaceutical infusion solutions. The RSD values were 0.15% or 1.07% (n=6) when determining 100 mg mL(-1) of MA or 50 mg mL(-1) of SO in commercial infusion solutions. The results were in good agreement with those of pharmacopoeial iodimetric titration.     

Characterization of exopolysaccharides in marine colloids by capillary electrophoresis with indirect UV detection

A method was established using capillary electrophoresis with indirect UV detection for analysis of monosaccharides liberated from exopolysaccharides by acidic hydrolysis. Tangential flow filtration was used to isolate high molecular weight polysaccharides from seawater. The capillary electrophoresis method included the use of a background electrolyte consisting of 2,6-dimethoxyphenol and cetyltrimethylammonium bromide. Several neutral sugars commonly existing in marine polysaccharides were separated under optimized conditions. The relative standard deviations were between 1.3% and 2.3% for relative migration time and 1.3-2.5% for peak height. Detection limits (at S/N 3) were in the range of 27.2-47.8 μM. The proposed approach was applied to the analysis of hydrolyzed colloidal polysaccharides in seawater collected from the Baltic Sea. Nanomolar levels of liberated monosaccharides in seawater samples can be detected by preconcentration up to 30,000 times.     

毛细管电泳-间接紫外检测法测定蜂蜜中的氨基酸

采用毛细管电泳-间接紫外检测法同时分离测定蜂蜜中的赖氨酸、色氨酸、谷氨酸等9种氨基酸。考察了磷酸浓度、进样方式和缓冲液pH对分离效率和重现性的影响。在分离电压为-15 kV、检测波长为220 nm条件下,以含有0.5 mmol/L十六烷基三甲基溴化铵、20 mmol/L烟酸、10%甲醇的10 mmol/L磷酸二氢钠缓冲溶液(pH 10.2)为运行缓冲液,9种组分在11 min内达到基线分离;检出限最低可达到0.3 mg/L;线性范围为1.0~1000 mg/L;日间及日内精密度为0.64%~5.83%。实际样品中除甲硫氨酸外的8种氨基酸的加标回收率为60.00%~118.37%。将该方法应用于不同蜜源植物和产地的蜂蜜样品的测定,在市售的5种蜂蜜中均检测到脯氨酸、丝氨酸和天冬氨酸,而只在荔枝蜜中检测到苏氨酸。该方法可以为蜂蜜的蜜源鉴别及质量评估提供借鉴方法。     

毛细管区带电泳-间接紫外法快速测定食品中的甜蜜素

建立了毛细管区带电泳-间接紫外法快速测定食品中甜蜜素的新方法。液体样品用超纯水稀释后直接进样;固体样品经粉碎或剪碎后用超纯水超声提取后离心,上清液直接进样或用水稀释后进样。以未涂敷石英毛细管（80 cm×75 μm,有效长度：70 cm）为分离柱,以2 mmol/L苯甲酸钠+10 mmol/L碳酸钠+0.5 mmol/L十六烷基三甲基溴化铵为分离缓冲液;于200 nm波长处检测。检出限为8.9 mg/kg （S/N=3）,定量限为26.7 mg/kg （S/N=9）。低、中、高添加水平的加标回收率分别为93.4%、100.3%及101.9%,相应的RSD分别为6.7%、2.0%及2.2%（n=5）。日内及日间精密度分别为2.6%和4.5%。整个分析过程无需有机溶剂。在能力验证样品的分析结果与国家标准方法的结果相吻合的基础上,分析了7件食品样品,获满意结果。     

Simultaneous determination of amphoteric surfactants in detergents by capillary electrophoresis with indirect UV detection

A simple, rapid and simultaneous determination of four types of amphoteric surfactants, i.e., C8, C10, C12, C14, C16 and C18-homologues of alkyldimethylamine N-oxide (AO), alkylamidopropylamine N-oxide (APAO), alkylbetaine (Bt) and alkylamidopropylbetaine (APB), was performed by using capillary electrophoresis (CE) with indirect UV detection. To optimize the separation conditions, effects of pH of background solution (BGS), organic modifier and chromophore for indirect UV detection on the CE separation of the amphoteric compounds were investigated. Addition of 50% (v/v) acetonitrile to the BGS under a lower pH condition brought a good separation performance due to the suppression of micelle formation for the analytes and the adsorption onto the inner surface of the capillary. Under an optimal condition, the 24 amphoteric analytes were completely separated in a single run within 17min. The relative standard deviation of the migration time was ranging from 0.20 to 0.23% and the limit of detection values for AO, APAO, Bt and APB homologues were 10-20, 20, 20-50 and 50microg/mL, respectively. Furthermore, the developed method can provide a high resolution separation of the amphoteric surfactants in commercially available detergents and shampoo without any sample pretreatments.     

Simultaneous determination of selenium and antimony compounds by capillary electrophoresis with indirect fluorescence detection

Capillary electrophoresis (CE) with indirect fluorescence detection was used to analyze selenium (selenite, selenate, selenomethionine, and selenocystine) and antimony (antimonite and antimonate) compounds. The separation was achieved by CE in 6 min with a 1.2 mM fluorescein solution at pH 9.5. Fluorescein also functioned as a background fluorophore for the indirect detection of these nonfluorescent species. Linearity of more than two orders of magnitude was generally obtained. Precision of migration times and peak areas was less than 1.0% and 7.2%, respectively. The concentration limits of detection (CLODs) was in the microM range. The detection sensitivity was generally dependent upon the transfer ratio (TR, defined as the number of moles of fluorescein ions displaced by one mole of analyte ions) of each species.     

Analysis of inorganic cations in honey by capillary zone electrophoresis with indirect UV detection

An indirect UV detection method based on capillary electrophoresis was developed to separate eleven metal cations completely, including alkali, alkaline earth and transition metal, which are related to evaluate the quality of honey. The background electrolyte contains 15 mmol/L chromophore imidazole, and acetic acid (pH = 3.7), which functioned as pH adjustor and complexing reagent. The selected cations can be completely separated within 8 min under hydrodynamic mode injection with a running voltage of 20 kV at 25°C. Limit of detection, linearity, reproducibility relative standard deviation of migration time and recoveries are in the range of 0.01-0.21 mg/L, 0.06-60.0 mg/L, 2.1-3.4% and 95.4-104.1%, respectively. The applicability of the method is shown by the analysis of honey samples, including a comparison with results of pretreatment and unpretreatment of eight samples. The results demonstrate that the developed method can conveniently be used in routine analysis of honey.     

Performance of a simple UV LED light source in the capillary electrophoresis of inorganic anions with indirect detection using a chromate background electrolyte

Light emitting diodes (LEDs) are known to be excellent light sources for detectors in liquid chromatography and capillary electromigration separation techniques, but to date only LEDs emitting in the visible range have been used. In this work, a UV LED was investigated as a simple alternative light source to standard mercury or deuterium lamps for use in indirect photometric detection of inorganic anions using capillary electrophoresis with a chromate background electrolyte (BGE). The UV LED used had an emission maximum at 379.5 nm, a wavelength at which chromate absorbs strongly and exhibits a 47% higher molar absorptivity than at 254 nm when using a standard mercury light source. The noise, sensitivity and linearity of the LED detector were evaluated and all exhibited superior performance to the mercury light source (up to 70% decrease in noise, up to 26.2% increase in sensitivity, and over 100% increase in linear range). Using the LED detector with a simple chromate-diethanolamine background electrolyte, limits of detection for the common inorganic anions, Cl-, NO3-, SO4(2-), F- and PO4(3-) ranged from 3 to 14 microg L(-1), using electrostatic injection at -5 kV for 5 s.     

Studying protein-drug interaction by microfluidic chip affinity capillary electrophoresis with indirect laser-induced fluorescence detection

We developed a microfluidic chip-affinity CE method based on indirect LIF detection to study protein-drug interactions. The interaction between heparin and BSA was quantitatively studied, as a model system. In our method, sodium fluorescein was chosen as background, and redistilled water as marker to monitor EOF. The electrophoretic mobility changes of BSA were measured, with various concentrations of heparin added to the running buffer. Each run was completed within 80 s. The binding constant was determined to be (1.24 +/- 0.05) x 10(3) M(-1), which was in good agreement with that reported in the literature.     

Separation of aminoalkanephosphonic acid enantiomers by indirect UV detection capillary electrophoresis with application of cyclodextrins

Indirect UV detection capillary electrophoresis (CE) was used for the separation of aminoalkanephosphonic acid (AP) enantiomers by applying commercially available cyclodextrins as chiral discriminators. The results show that the separation of the enantiomers depends on pH of the background electrolyte, the molar ratio of cyclodextrin to aminophosphonic acid, and on the type of the applied chiral selector. Optimization of process conditions allowed enantiomeric baseline separation or partial separation of 12 out of 14 alpha-aminophosphonic acids studied. This type of CE might therefore be successfully used for routine determination of enantiomeric purity of aminophosphonic acids.