同步热分析-傅里叶变换红外光谱-气相色谱-质谱法分析淀粉

应用同步热分析法对淀粉样品进行了热失重研究。分别在氮气和氮氧(91+9,体积比)混合气氛围中,对淀粉样品在动态升温条件下的热重、微分热重和温度变化曲线的差异进行了比较,将315℃和350℃时所得的热解产物进行傅里叶变换红外光谱和气相色谱-质谱分析,在氮气和氮氧混合气氛围下共检出并鉴定了51种化合物。     

糠醛渣热解特性的研究

以糠醛渣为研究对象,应用热重分析法,以高纯氮气为载气对其进行了详细的热重分析试验。结果表明糠醛渣热解随温度升高经历五个不同阶段,表现了糠醛渣热解的复杂性。通过对5 ℃/min、20 ℃/min、50 ℃/min和80 ℃/min的升温速率及不同粒径下的失重曲线进行的对比表明,随着升温速率和粒径的增大,糠醛渣热解的初始温度增大,热解向高温侧移动。最后根据实验数据建立了热解动力学模型,并对数学模型进行了求解,得到了糠醛渣热解反应的动力学参数,表明糠醛渣热解属三级反应。     

热重分析-傅里叶变换红外光谱法研究橡塑海绵的热氧降解

采用热重分析-傅里叶变换红外光谱法(TGA-FTIR)研究了空气中橡塑海绵的热氧降解行为。考察了材料在3个不同升温速率下的失重情况,并对材料失重过程逸出的气体进行了分析。结果表明:橡塑海绵有两个失重阶段,随着升温速率的增大,材料的失重速率增加,最大失重速率温度有所升高;第一失重阶段是橡塑海绵中丁腈橡胶(NBR)和聚氯乙烯(PVC)官能团的热解,主要生成氯化氢及氰酸类气体;第二失重阶段是橡塑海绵中碳链的热氧降解,主要生成二氧化碳。     

城市污水污泥燃烧特性和动力学特性分析

采用热重分析仪对城市污水污泥进行热重实验,通过TG(热重)、DTG(微分热重)和DSC(差示扫描量热)曲线的分析对比,获得污水污泥热解和燃烧不同阶段的特性。低于250℃,燃烧与热解的热重曲线基本吻合,说明在此之前,失重速率主要受控于有机物的分解以及析出,燃烧过程对失重影响不明显。燃烧DTG曲线呈现“W”峰型,第一个失重速率峰与热解DTG曲线基本对应,高于410℃,燃烧DTG曲线出现显著的加速。采用Coats-Redfern 积分法,假设不同的反应模型进行拟合,推断出污泥燃烧过程中两个DTG峰体现出不同的反应机理。借鉴煤燃烧机理分析认为,污泥燃烧反应初期挥发分的燃烧受控于化学反应速率,随着温度的不断提高,剩余挥发分的燃尽和固定碳的燃烧总反应速率逐渐受扩散因素控制。基于分析所得污泥燃烧机理,采用四个独立的平行反应模型模拟污泥的燃烧过程,拟合曲线与实验数据吻合良好。     

热分析法研究五倍子醛的热稳定性及其分解动力学

采用热重法,以氮气为保护气,分别在5、10、15、20℃/min的升温速率下,测得五倍子醛的热重-微分热重(TG-DTG)曲线,并在10℃/min的升温速率下测得样品的差示扫描量热(DSC)曲线。结合热失重数据和五倍子醛结构对其分解机理进行推断和验证,并运用双外推法对五倍子醛的热解动力学进行分析,求得原始状态和热平衡态下的动力学参数。研究结果表明,五倍子醛晶体在升温过程中先经历了非结合水和结合水的受热挥发阶段,然后在163℃之后发生热分解,分子中醛基断裂失去1分子的CO;随着升温速率的升高,五倍子醛的分解反应向高温区域移动,最大失重速率依次减小;热解活化能Eα为286.21 kJ/mol,指前因子lnA为70.21,热解机理函数g(α)=[-ln(1-α)]2/3,反应级数n=2/3;热解活化能随转化率的增加逐渐减小;经动力学参数推断,在室温(25℃)下,五倍子醛的贮存期为4～5年。     

马瑞原油在空气和氮气中的热解-氧化性能

低温氧化是注空气采油及原位燃烧采油技术中的重要化学反应,为深入认识原油在有氧环境下复杂热反应过程中的低温氧化特性,我们采用热重/差热分析法(TG/DTA)研究了线性升温和等温条件下马瑞(Merey)原油的热反应行为。 结果表明,Merey原油在空气及线性升温条件下的受热过程分4个阶段:气化段、低温氧化段、热解段和高温氧化段;相邻阶段的物理、化学主导过程的重叠增加了分析原油热反应特征的难度。 升温速率提高,气化段和低温氧化段的终止温度不变;热解段和高温氧化段的终止温度以及热解段的峰温随升温速率的增加而升高。 N₂气与空气下Merey原油的热重/微分热重(TG/DTG)数据对比表明,升温速率越高,空气下的高温氧化段与热解段重叠程度越大,这有利于燃烧但会降低原油采收率。 空气下等温时的TG/DTA结果表明随升温速率增加,升温至300 ℃时的失重率降低,不利于原油轻组分的气化。 反应温度越高,气化过程时间越长,失重分数越大。 Merey原油在低于300℃时低温氧化反应不是主导反应。     

生物质秸秆热重分析及几种动力学模型结果比较

利用热重分析在不同升温速率和氮气气氛下对两种生物质（玉米秸秆和稻秆）的热失重行为进行了研究。根据热重实验数据，采用四种利用热分析获取动力学参数的方法（Coats-Redfern法，Doyle法，最大速率法和分布活化能模型(DAEM)），计算生物质秸秆热分解反应活化能E、反应级数n及频率因子A，并进行比较。结果表明，采用不同的处理方法，得出的热分解动力学参数不同。利用Coats-Redfern法，玉米秸秆和稻秆在热解主要阶段（失重约5 w%～80 w%时）可由一段一级反应过程描述，升温速率10 K/min时活化能值分别为68.8 kJ/mol和70.0 kJ/mol。Doyle法和DAEM模型得到的结果较为接近，可以得到生物质热解过程中的活化能随失重率的变化曲线。生物质秸秆热解包含分子键能断裂的一系列复杂、连续反应过程。     

污泥与煤和煤矸石共燃特性研究

利用STA 409 PC型同步热分析仪,对煤、煤矸石和污泥不同质量比样品的燃烧过程进行了热重分析。结果表明,单一煤和煤矸石的DTG曲线都只有一个明显的失重峰,污泥的DTG曲线有两个明显的失重峰,而混合物的DTG曲线都有两个失重峰。通过分析不同样品的混燃过程,发现随着煤所占质量比的增加,最大失重峰速率所对应的温度都有所降低。煤、煤矸石、污泥及其混合物的活化能为16.93kJ/mol～109.89kJ/mol。随着污泥所占质量比的增加,混合物的着火温度有所降低,当达到70%时,污泥与煤混合物的着火点接近单一污泥的着火点。     

煤直接液化残渣及其萃取产物的热重分析

利用热天平考察了神华和胜利两种典型中国煤直接液化残渣及其萃取产物的失重曲线。实验表明,神华残渣和胜利残渣的轻质组分含量相近,其失重率也相近,但轻质组分组成不同使得失重过程并不一致 。升温速率增加,热解最大失重速率增加,最大失重速率温度升高。以残渣各组分失重曲线拟合得到的残渣失重曲线可近似表示残渣的失重曲线。动力学分析表明,由实验数据拟合的活化能和指前因子计算得到的失重曲线,与实际实验得到的失重曲线较为一致。液化残渣在低温区失重率很高,而且这部分失重产物可以通过溶剂萃取的方式得到。     

一种煤与两种城市污水污泥混合热解的热重分析

采用热重分析法对一种煤和两种城市污水污泥（S1和S2）及其混合物进行了热解实验研究,揭示了煤和污泥在氮气中的热解特性及污泥对煤热解特性的影响。煤和污泥的热解特性参数不同,主要表现在总失重率、失重速率及挥发分析出温度区间等。煤与污泥S1混合有助于增加样品的热解总失重率,提高失重速率;污泥S1与煤的挥发分析出区间部分重合,污泥灰中含的无机物对煤的热解起到催化效果;煤和S2污泥混合后热解反应过程中无明显相互作用;煤与城市污水污泥混合物的相互作用与样品特性和混合比例有关。     

Simultaneous non-invasive microwave dielectric spectroscopy and dynamic mechanical analysis for studying drying processes

The aim of this paper is to describe how a dynamic mechanical analyser can be used together with the microwave coaxial line technique. This coupling enables the simultaneous recording of changes in the mechanical properties and moisture content of materials as a function of time or temperature at a selected frequency. The sample is placed either directly under the probe or clamped in the sample holder of the dynamic mechanical analyser. Sample positioning and heating is accurately controlled by the mechanical analyser and its temperature controller. Samples can be subjected to a constant static force, a frequency or both. A micro probe, recently designed for measurements on semi-rigid and rigid surfaces [1], and connected to a network analyser was used to monitor the moisture content of the samples.     

Morphology of polyethylene crystallized by solution stirring

Dilatometric and calorimetric studies have been made of the fusion process of linear polyethylene crystallized by stirring xylene solutions at elevated temperatures. It is shown that the melting point of the crystals increases rapidly from 139.5°C to 145°C in the crystallization temperature range of 100–103°C and levels off to 146 ± 0.5°C, provided that very slow heating rates are employed. Stirrer-crystallized samples treated with fuming nitric acid show higher crystalline contents. Comparison of their enthalpies of fusion and melting points indicate that higher molecular order along the fiber axis is associated with higher crystallization temperatures. This is in general agreement with corresponding results of other modes of crystallization. The attack of fuming nitric acid on stirrer crystals is characterized by weight-loss curves similar to those of dilutesolution crystals and bulk polyethylene. The linear molecular weight dependence on time of exposure to nitric acid suggests that the oxidation proceeds mainly from the chain ends at a constant rate for samples stirred in the lower crystallization range, but an increased rate is observed for a sample stirred from xylene at 105°C. It is suggested that the lamellar overgrowths, most evident at low crystallization temperatures, are epitaxially attached to the fiber axis, whereas the smaller crossbandings observed at higher crystallization temperatures are possibly made up of elements of chains that are only partly incorporated in the highly ordered fibrous core.     

Thermal gradients in differential scanning calorimetry

A combined static and dynamic temperature calibration is described. The static calibration corrects the instrumental dial temperature reading. The dynamic calibration has instrumental and material components and therefore varies from specimen to specimen. It is obtained from individual DSC curves and so removes uncertainties in sample temperature due to varying mass, geometry, and heating rate. The instrumental performance is improved and specific heats may be obtained to an accuracy of ±1%.     

Melting of constrained drawn nylon 6 yarns

A differential scanning calorimeter (DSC) was used to study the melting behavior of drawn nylon 6 yarns which were prevented from shrinking during heating. The DSC curves exhibit a single melting peak at a higher temperature instead of the double peaks which, as reported previously, were observed in the unconstrained state. The curve is explained quantitatively in terms of the perfecting of the original crystals followed by monotonic melting of these crystals during heating. The single peak results from the absence of the partial melting–recrystallization process which plays an important role in the appearance of double peaks. The temperature of the melting peak for the constrained sample increases linearly with draw ratio, and is unaffected by drawing temperature and by annealing at constant length after drawing. The elevation of the melting temperature is discussed on the basis of the entropy effects predicted theoretically by Zachmann. Thermal analysis of constrained samples has proved to be useful for detecting oriented crystals which coexist with unoriented ones.     

Kinetics of Extraction of Biologically Active Substances from Medicinal Plant Raw Materials using Different Techniques

The problems and peculiarities of obtaining the kinetic characteristics of extraction of biologically active substances (BAS) from a plant matrix are discussed. The establishment of kinetic characteristics of the extraction of BAS under various extraction conditions is studied on the example of samples of Hypericum perforatum and Salvia officinalis. The lowest value of the average rate constant of the extraction of BAS from the materials examined is characteristic of a variant of static extraction with an aqueous alcohol extractant under heating. The methods of static extraction under heating (according to the requirements of pharmacopoeia articles) and ultrasonication, as well as using double ultrasonication differ little from each other in their kinetic efficiency. The method of dynamic extraction of BAS at an elevated temperature and pressure is characterized by the highest values of the rate constant, which leads to an acceleration of the diffusion of the BAS into the extractant’s medium. It is noted that the extraction processes and chemical transformations of some BAS (hyperforin, carnosic acid, etc.) occur simultaneously as confirmed by the decrease in their concentrations in the extractant during the extraction from plant samples.     

Polyvinylpyrrolidone thin film pyrolysis as accessed by the real-time optical transmission measurements

Present results reveal basic features of the optical transmission thermo-analytical method in its employment to investigate the oxidative pyrolysis of supported thin polyvinylpyrrolidone films. The OT curves naturally vary in shapes and positions on the time/temperature scales, respective to the examined rate of sample heating, to the wavelengths of radiation as well as to the film thickness. Recorded OT curves exhibit characteristic shapes with well-expressed OT minima. The temperatures at which the OT minima appear are in a linear relationship with heating rates of samples, at a frequency of radiation as well as a film thickness kept constant. Similarly, the OT values at which the OT minima appear are in a linear relationship with film thickness, at a frequency of the radiation and sample heating rate unchanged.     

机械振动对聚丙烯结晶作用的影响

对热塑性高分子作熔体加工时,在此过程中同时再叠加机械振动,设计制造的加工机器一方面具有卓越的技术经济指标,另一方面制品的物理性能也得到了提高[1,2].此类研究的重点多集中在动态成型过程中聚合物的流变行为或者成型后制品的力学性能方面[3,4],对聚合物本身在此外加交变力     

Heating and temperature gradients of lipid bilayer samples induced by RF irradiation in MAS solid‐state NMR experiments

The MAS solid‐state NMR has been a powerful technique for studying membrane proteins within the native‐like lipid bilayer environment. In general, RF irradiation in MAS NMR experiments can heat and potentially destroy expensive membrane protein samples. However, under practical MAS NMR experimental conditions, detailed characterization of RF heating effect of lipid bilayer samples is still lacking. Herein, using ¹H chemical shift of water for temperature calibration, we systematically study the dependence of RF heating on hydration levels and salt concentrations of three lipids in MAS NMR experiments. Under practical ¹H decoupling conditions used in biological MAS NMR experiments, three lipids show different dependence of RF heating on hydration levels as well as salt concentrations, which are closely associated with the properties of lipids. The maximum temperature elevation of about 10 °C is similar for the three lipids containing 200% hydration, which is much lower than that in static solid‐state NMR experiments. The RF heating due to salt is observed to be less than that due to hydration, with a maximum temperature elevation of less than 4 °C in the hydrated samples containing 120 mmol l^?1 of salt. Upon RF irradiation, the temperature gradient across the sample is observed to be greatly increased up to 20 °C, as demonstrated by the remarkable broadening of ¹H signal of water. Based on detailed characterization of RF heating effect, we demonstrate that RF heating and temperature gradient can be significantly reduced by decreasing the hydration levels of lipid bilayer samples from 200% to 30%. Copyright © 2016 John Wiley & Sons, Ltd.     

圆盘膜萃取-气相色谱-质谱法同时测定水中16种酞酸酯类化合物

提出了气相色谱-质谱法同时测定水中16种酞酸酯类化合物(PAEs)的方法。采用自制圆盘萃取装置、无塑料制品接触试验程序进行水样富集,对圆盘膜片选择、过膜压力、洗脱剂种类与用量等进行考察;对仪器工作条件离子源温度、升温速率、进样口温度和不同时间段监测离子及增益等进行了探讨。16种PAEs的质量浓度分别在一定的范围内与峰面积呈线性关系,检出限(3S/N)在0.17～2.45μg.L-1之间。以空白蒸馏水为基底,在3个浓度水平下做加标回收试验,回收率在79.8%～104%之间,相对标准偏差(n=6)在1.1%～9.4%之间。     

On the non-isothermal determination of activation energy for thermal decomposition reactions

Attention is called to the frequently encountered linear sector in the isothermal course of the topochemical processes which is used in the kinetic treatment of the differential curves of thermal CoOOH decomposition. The effect of sample weight and heating rate on the values of the activation energy of this process under polythermal conditions has been investigated. Most of the values obtained are in good agreement among themselves as well as with those found isothermally. Existing differences have been explained satisfactorily.