固相萃取-衍生化-气相色谱-质谱法测定水中类固醇类雌激素

采用固相萃取-衍生化-气相色谱-质谱法同时测定水中4种类固醇类雌激素雌酮(E1)、17β-雌二醇(E2)、17α-乙炔基雌二醇(EE2)、雌三醇(E3)。样品经Oasis HLB固相萃取柱,以丙酮为溶剂进行洗脱后,采用吡啶、N-甲基-N-三甲基硅基三氟乙酰胺于40℃衍生化20min后,采用气相色谱-质谱仪分析。E1、E2、EE2和E3的线性范围分别为5.00~500μg·L-1和10.0~500μg·L-1,4种类固醇类雌激素的检出限(3S/N)在1.5~3.0μg·L-1之间,测定下限(10S/N)在5.0~10μg·L-1之间;方法用于实际水样的分析,加标回收率在86.8%~93.8%之间,测定值的相对标准偏差(n=7)在7.1%~11%之间。     

类固醇类环境内分泌干扰物羟基衍生化研究

采用气相色谱-质谱联用技术(GC-MS),以N,O-双三甲基硅基三氟乙酰胺为衍生化试剂,系统研究了4种类固醇类环境内分泌干扰物雌酮(E1)、17β-雌二醇(E2)、雌三醇(E3)、17α-乙炔基雌二醇(EE2)的羟基衍生化行为,考察了BSTFA用量、衍生化温度和时间对类固醇类环境内分泌干扰物衍生化效果的影响以及衍生化产物的稳定性、标准曲线、仪器检出限等,并对衍生化产物特征碎片离子的裂解机理进行了解释.结果表明:对于100 μL 0.01 g/L标准混合溶液,BSTFA的最佳用量为25 μL;衍生化过程不需要加热,常温下(20 ℃)下反应10 min就可取得最佳的衍生化效果;衍生化产物的稳定性较好,在-20 ℃下放置48 h,相对响应因子RRF基本没有降低.在优化的实验条件下,各待测物具有良好的线性相关性,E1和E2的检出限为0.3 μg/L,EE2和E3的检出限为5 μg/L.     

固相萃取-分散液液微萃取-柱前衍生法测定水样中痕量雌激素

建立了碳纳米管的固相萃取-分散液液微萃取-柱前荧光衍生化(SPE-DLLME-PFD)测定水体中痕量雌三醇(E3)、双酚A(BPA)、17α-乙炔基雌二醇(EE2)及17β-雌二醇(E2)的高效液相色谱方法.采用中心复合设计和响应曲面法分析并优化SPE、DLLME及PLD条件,最佳条件为210 mL水样以2.0 mL/min的流速过固相萃取柱(碳纳米管量30 mg),甲醇洗脱,氮气浓缩并定容至0.6 mL(分散剂),将100 μL C6MIM[PF6]与分散剂的混合液注入到NaCl含量为25％的2.0 mL去离子水中,离心,移取20 μL下层有机相于样品瓶中,与4.0 mg衍生剂混合,在40℃水浴中衍生25 min;用0.1mL甲醇溶解过量的衍生剂颗粒,取20 μL进样分析.在优化条件下.4种雌激素的线性范围为0.05～5.00 μg/L,相关系数R2=0.9966～0.9999;,检出限介于0.13～6.33 ng/L(S/N=3)之间.不同加标浓度条件下,雌激素的加标回收率在83.1％～122.4％范围内(RSD=1.7％～9.6％).在实际水样中E3和BPA检出率较高.与其它方法相比,本方法虽然萃取时间长、水样量大、步骤多,但具有检出限低、操作简便、环境友好等优点.     

基于碳纳米管的固相萃取-分散液液微萃取测定水中多种痕量环境雌激素

建立了基于碳纳米管的固相萃取-分散液液微萃取/ 上浮溶剂固化-高效液相色谱/荧光法测定水体中痕量雌激素雌三醇(E3)、 双酚A(BPA)、 17α-乙炔基雌二醇(EE2)及17β-雌二醇(E2)的方法. 利用中心复合实验设计分别对固相萃取和分散液液微萃取条件进行了优化, 通过响应曲面法得到的最佳萃取条件为碳纳米管用量30 mg, 水样体积210 mL, 流速2.0 mL/min, 萃取剂(十二醇)体积50 μL, 分散剂(甲醇)体积0.2 mL以及不添加盐. 在优化的实验条件下, E3, BPA, EE2和E2测定的线性范围分别为0.05~100, 0.05~100, 0.05~50和0.05~50 μg/L, 相关系数为0.9993~0.9999, 检出限分别为48.4, 3.3, 8.1和6.0 ng/L. 对不同加标浓度(0.40和4.00 μg/L)的实验室自来水、 排水沟污水及市售矿泉水3种实际水样进行了分析: E3, BPA, EE2和E2的加标回收率依次为107.5%~120.8%, 92.5%~108.3%, 103.5%~121.0%和102.5%~132.5%, 相对偏差分别为2.47%~13.28%, 1.73%~11.94%, 1.72%~8.36%和3.54%~11.95%, 富集因子平均值分别为461, 1075, 2074和949. 实际水样分析结果表明, 本方法可用于不同基质水样中雌激素的测定. 与其它方法相比, 本方法虽然固相萃取时间长及水样量大, 但检出限低、 富集因子高、 操作简便及费用低, 仍可作为一种可普及的水中痕量雌激素检测方法.     

固相萃取-气相色谱/质谱联用法同时检测水体中9种环境雌激素

建立了固相萃取-气质联用法(SPE-GC-MS)测定水体中9种环境雌激素:雌酮(E1)、17b-雌二醇(E2)、雌三醇(E3)、4-辛基酚(OP)、4-壬基酚(NP)、双酚A(BPA)、己烯雌酚(DES)、美雌醇(EE3ME)和17a-炔雌醇(EE2)的检测方法,优化了萃取和衍生化反应条件,实验结果表明:HLB柱回收率较高,衍生化反应的温度为75℃,衍生时间为90 min;本方法对9种环境雌激素的加标回收率为60.5%～126.7%,对应的相对标准偏差为0.8%～11.1%,方法检出限为1.08～8.60 ng/L,并将本方法应用于实际环境水样的检测。     

固相萃取-衍生化气相色谱/质谱法测定制药厂污水中的环境雌激素

采用固相萃取-衍生化气相色谱/质谱法(GC/MS)测定某制药厂污水中的雌酮(E1)、雌二醇(E2)、雌三醇(E3)和乙炔基雌二醇(EE2)4种雌激素化合物。样品经固相萃取柱萃取富集及双(三甲基硅烷基)三氟乙酰胺(1%三甲基氯硅烷)（BSTFA(1%TMCS)）衍生化后进行GC/MS分析。该法对4种目标物的检出限为1.8～4.7 ng/L,相对标准偏差为2.3%～9.1%(n=8)。目标化合物的加标回收率为（94.0±2.9）%～（101±3.8）%,说明该方法能较好地应用于污水中雌激素化合物的定量检测。通过对某制药厂污水中的雌激素进行定量分析,发现污水中乙炔基雌二醇和雌酮质量浓度分别达396.6 和39.9 ng/L;经过传统的厌氧兼氧好氧生物处理后,污水中的环境雌激素的去除率仅为35%～40%,说明传统的污水处理工艺对去除污水中雌激素效果并不明显,需要改进。     

氟化物衍生-~(19)F-核磁共振法检测水样中氰化物

取69.8mg·L~(-1)氰化钠溶液0.50mL,用0.25mol·L~(-1)氢氧化钠溶液调节其酸度至pH 12,减压蒸发至干。加入二甲基亚砜(DMSO)0.5mL溶解残渣,随后加入2,2,2-三氟苯乙酮(TFAP)10μL和乙酸酐20μL,室温下反应45min,使氰根衍生为1-氰基-2,2,2-三氟~(-1)-乙酸苯乙酯(CTPA)。取0.30mL上述溶液,加入7.78mmol·L~(-1)乙酸~(-3)-氟苄酯-氘代三氯甲烷(CDCl3)溶液0.2mL为内标,按仪器工作条件进行~(19)F-核磁共振(NMR)分析。试验表明该衍生方法的检出限为0.7mg·L~(-1)。方法不受其他干扰离子(如CO_3~(2-)、B_4O_7~(2-)、Cl~-、SO_4~(2-)等)的影响,具有良好的专属性。选用3种不同水源的水样(自来水、河水、纯水)按所提出方法衍生化并测定,三者的回收率依次为74.0%,74.0%,75.0%,并无大的差别,3种水样测定值的相对标准偏差(n=6)依次为2.1%,2.4%,3.0%。方法曾用于天津8·12爆炸区采集的水样中氰根的测定,获满意结果。     

雌酮、17β－雌二醇与17α－乙炔基雌二醇在污水样中的稳定性研究

雌酮(E1)、雌二醇(E2)和炔雌醇(EE2)在ng·L-1的浓度水平即可干扰生物的内分泌系统,在英国即将被限制排放.论文研究了在三种水样保存方式下污水厂进水和尾水中E1,E2和EE2浓度的变化.研究显示:(A)在4℃,避光保存,三种雌激素在进水样中降解率为22%、34%和4%;在尾水样中则分别为14%、26%和2%.(B)在4℃避光及pH=2(英国环保署常规有机污染物保存方法)保存条件下,E1、E2和EE2在2天内在进水样中的损失率为8%、20%和4%;在尾水样中的损失率分别为4%、17%和1%.(C)在水样中加入Cu(NO3)2抑制剂至250mg·L-1并用HCl调节至pH=3在低于10℃避光保存,可保证E1、E2和EE2在15天内损失＜3%.采用方式C保存水样有利于提高分析检测E1、E2和EE2的准确度和重现性.     

气相色谱-质谱法测定尿及河底泥中的环境雌激素

报道了尿及河底泥中环境雌激素(壬基酚、双酚A、己烯雌酚、17α-乙炔基雌二醇)和内源性雌激素(17α-雌二醇、17β-雌二醇、雌三醇、雌酮)的气相色谱-质谱(GC-MS)测定法。尿样经盐酸溶液水解后用固相萃取(SPE)柱浓缩净化,底泥样品用甲醇-乙酸乙酯萃取。被测组分经五氟丙酸酐(PFPA)衍生化后用GC-MS进行定性定量检测。该法测定的峰面积的日内相对标准偏差为1.22%-5.55%,检出限为0.05-1.27 μg/L(或μg/kg)。被测组分的加标回收率除尿样中17α-乙炔基雌二醇和己烯雌酚分别为2     

分散液液微萃取-柱前衍生-高效液相色谱法测定水样中双酚A

建立了分散液液微萃取-柱前衍生-高效液相色谱法测定水样中双酚A的分析方法.通过交互正交试验和混合型优化实验设计对影响因素(萃取剂体积、分散剂类型及其体积、水样体积、pH值及离子强度)进行了优化.优化后的分散液液微萃取条件为:60 μL萃取剂,0.4 mL分散剂(甲醇),pH 4.0;优化后的柱前衍生化条件:0.1 mL 2.0 g/L衍生剂(对硝基苯甲酰氯)、衍生化时间30 min;方法的线性范围:0.002～0.2 mg/L(r=0.9997),检出限0.007 μg/L(S/N=3);不同浓度双酚A的萃取率为59.0%～63.0%,相对标准偏差(RSD)2.5%～9.2%(n=5);水样中双酚A的加标率为86.5%～107.1%,RSD为4.0%～11.9%(n=5),其它雌激素(雌酮、雌二醇、雌三醇和17α-乙炔基雌二醇)对双酚A的测定无干扰.本方法可以对水环境中的痕量BPA进行检测,具有操作简便、快速等优点.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.