微波消解ICP-AES法同时测定蒙药新-Ⅱ中多种微量元素及Ca/Mg,Cu/Zn比值的分析

采用微波消解ICP—AES法同时测定蒙药新-Ⅱ中Ca、Mg、Fe、Zn、Ni、Mn、Cu、Pb等15种微量元素,并对蒙药新-Ⅱ中Ca／Mg,Cu／Zn比值进行了初步的分析。结果表明,蒙药新-Ⅱ中含有多种微量元素,其中人体有益的微量元素Ca、Mg、Fe、Cu、Ni、Zn、Mn的量相对高,即Ca〉Mg〉Fe〉Mn〉Zn〉Ni〉Cu,而人体有害微量元素Cd、Pb、Ag的量相对较低,Ca／Mg和Cu／Zn比值分别为4．1760、0．6077。加标回收率在97．5％～105．5％之间,相对标准偏差RSD≤2．7％,检出限≤0．008μg／mL。     

桂花中微量元素的光谱测定

采用火焰原子吸收法同时测定了桂花中K、Na、Ca、Mg、Pb、Cd、Cu、Mn、Co、Zn、Cr、Fe等十二种微量元素的含量。方法的相对标准偏差介于0．07％～2．31％之间,回收率介于93．0％～106．0％之间,分析结果满意,并表明,桂花中含有丰富的金属元素,元素含量由高到低排列顺序为：K,Ca,Mg,Na,Fe,Zn,Cu,Mn,Pb,Co,Cr,CA,说明桂花具有较高的营养价值。     

电感耦合等离子体原子发射光谱法(ICP-AES)测定不同品种山药中矿物质元素与对比研究

采用微波消解样品,运用电感耦合等离子体原子发射光谱法同时测定山药中K,Na,Ca,Mg,Zn,Fe,Cu,Mn,Se,Pb,Cd和Cr 12种元素。结果表明:方法简便、快速、准确;山药富含对人体有益的K,Ca,Fe,Mg,Zn,Mn,Se等矿物质元素,其肉质中重金属元素Pb,Cd,Cr含量均未超过国家食品卫生标准。     

微波消解/ICP—AES法测定不同品种山药中矿物质元素与对比研究

采用微波消解样品,运用电感耦合等离子体原子发射光谱法同时测定山药中K、Na、Ca、Mg、Zn、Fe、Cu、Mn、Se、Pb、Cd和Cr等12种元素。结果表明：方法简便、快速、准确度高;四种山药均富含对人体有益的K、Ca、Fe、Mg、Zn、Mn、Se等矿物质元素,其肉质中Pb、Cd、Cr含量均未超过国家食品卫生标准。     

FAAS法测定红树内生真菌Nigrospora sp.菌体中的微量元素

目的测定红树内生真菌Nigrospora sp.菌体中的微量元素。方法采用火焰原子吸收光谱法(FAAS)对湛江红树木榄内生真菌菌体中的Fe、Zn、Cu、Ca、Mg、Mn、Cd和Pb等微量元素进行了分析测定,结果发现其Fe、Zn、Cu、Ca、Mg和Mn等元素的含量都比较丰富,未检出Cd和Pb。数据显示相对标准偏差为0.30%～3.93%,回收率为96.8%～102.6%,结论该法快速、简单、结果可靠,为进一步对红树木榄内生真菌探讨研究提供更全面的分析数据。     

ICP-AES法同时测定配合饲料中的微量元素

采用ICP—AES法同时测定配合饲料中Cu、Fe、Mn、Zn、Ca、Mg、P、Pb、Cr、Cd元素的含量。选择了合适的分析线、溶样酸及酸的用量，各元素测定结果的相对标准偏差为0．40％～6．52％，回收率为90．8％～104．5％。     

原子吸收光谱法测定宁夏几种中草药中微量元素含量

采用原子光谱法测定了宁夏几种野生中草药苦豆子、败酱草、老瓜头全草及根、茎、叶中Ca、Mg、Fe、Mn、Zn、Cu、Pb、Cd 8种元素的含量。结果表明,几种野生中草药Ca、Mg、Fe、Mn、Zn、Cu含量较为丰富,Pb含量低,Cd未检出,分析结果对几种中草药的辨证使用及其生长环境的研究具有一定的实际意义。     

松口蘑中微量元素的测定

采用火焰原子吸收法同时测定了松口蘑中K、Ca、Na、Mg、Fe、Pb、Cd、Co、Cr、Zn、Mn、Cu等12种元素的含量。方法的相对标准偏差在0.08％－2.32％范围,回收率在97.1%－108.3%范围。结果表明,在三种松口蘑样品中,除含有较高的K、Na、Ca、Mg和一定量的有害元素Cd、Pb外,其余6种对人体有益的微量元素较为丰富。     

白族长寿地区硬果仁中19种元素的测定分析

用电感耦合等离子体发射光谱法（ICP－AES）,对云南省白族长寿区的葵花子仁、麻子仁和核桃仁中的Ca、Mg、P、S、Na、AI、B、Fe、Zn、Cu、Mo、Sr、Mn、Cr、Se、Ge、Cd、Pb、As等19种元素进行了测定分析。结果表明,3种硬果仁中含有丰富的人体必需的Ca、Mg、P、S、Na、Fe、Zn、Mn、Se、Cu、Cr、Sr、Mo等有益元素,且P、Mg、S、Ca、Na、Zn、Mn、Fe、Se的含量较高。这些生命元素在3种硬果仁中的含量存在差异。有害元素Cd、Pb均未检出,核桃仁中As含量较高。硬果仁中富含这些生命元素是该地区老人健康长寿的一个重要原因。     

藏药材白花龙胆花中微量元素的分析

对藏药材白花龙胆花中17种微量元素（Cu、Zn、Fe、Mn、Co、Ni、Se、Cr、Mg、Ca、K、Na、P、As、Hg、Pb、Cd）的含量作了测定。结果表明,白花龙胆花中含有较高的人体必需微量元素和常量元素,其中常量元素K、Ca、Na、Mg和微量元素Zn、Fe、Mn的含量均较高。     

智能石墨消解–ICP–MS法测定空气PM2.5中的Pb和Cd

建立电感耦合等离子体质谱(ICP–MS)测定空气PM2.5中的Pb和Cd元素的分析方法。采用连续β射线–DHS PM2.5大气颗粒物浓度监测仪采集空气中的PM2.5,以智能石墨消解PM2.5滤膜样品,ICP–MS测定其中的Pb和Cd元素含量。在优化的仪器条件下,元素Pb和Cd标准曲线的线性相关系数均为0.999 9,检出限分别为0.018,0.52ng/m3,满足HJ 657–2013的要求。Pb和Cd的加标回收率分别为95.8%~101.4%,99.3%~104.9%,测定结果的相对标准偏差分别为4.20%和2.38%(n=6)。对滤膜标准样品进行了测定,测定结果与标准值一致。该方法测定结果准确、可靠,可用于测定空气PM2.5中的Pb和Cd。     

Direct determination of Cd, Cu and Pb in wines and grape juices by thermospray flame furnace atomic absorption spectrometry

The applicability of thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) was evaluated for direct determination of Cu, Cd and Pb in wines and grape juices. The developed procedure does not require preliminary acid digestion of the samples. The optimum conditions for determination of Cu, Cd and Pb in wines were studied and the performance was compared to those typically obtained by flame atomic absorption spectrometry (FAAS). A sample volume of 150 microL was introduced into a heated nickel tube at a flow rate of 0.54 mLmin(-1) and 0.14 molL(-1) HNO(3) was used as sample carrier flowing at 2.5 mLmin(-1) for determining all analytes. The effect of ethanol concentrations on Cu, Cd and Pb absorbance signals were studied. All determinations were carried out by adopting optimized conditions and quantification was based on the standard additions method. Limits of detection (LOD) of 12.9, 1.8 and 5.3 microgL(-1) (n=14) for Cu, Cd and Pb, respectively, were obtained for wine samples (3sigma(blank)/slope, n=14). Relative standard deviations (R.S.D., %) of 2.7, 2.1 and 2.6 for Cu, Cd and Pb, were obtained (n=6) for wine samples. The values determined for grape juice samples were similar to these ones. The analytical throughput was 45 determinations h(-1) and accuracy was checked by addition-recovery experiments.     

微波消解-ICP-AES法测定塑料中Pb和Cd

采用微波消解法进行溶样,以ICP-AES法测定塑料中Pb和Cd的含量。Pb、Cd的回收率分别为96.0%~102.0、93.3%~105.0%。Pb、Cd测定结果的相对标准偏差分别为0.567%、1.19%(n=10)。Pb和Cd的检出限分别为0.02、0.005 mg/L。该方法适用于多种塑料中Pb和Cd含量的快速分析。     

Determination of Ba, Cd, Cu, Pb and Zn in saliva by isotope dilution direct injection inductively coupled plasma mass spectrometry

Trace elements in small sample volumes of saliva were determined by coupling a high efficiency direct injection nebulizer to inductively coupled plasma mass spectrometry and employing quantification by isotope dilution. Aliquots of 0.4 ml of human saliva were mixed with 0.1 ml of concentrated nitric acid and diluted to 2 ml with water. Sample solutions were spiked with an isotopic solution enriched in 135Ba, 112Cd, 65Cu, 206Pb and 66Zn. The amount of each isotope added to the samples and the measurement procedure were adjusted to attain precise analytical results calculated from the isotope ratios 135Ba/138Ba, 112Cd/114Cd, 65Cu/63Cu, 206Pb/208Pb and 66Zn/68Zn. Data acquisition for Ba, Cu and Zn isotopes was performed for a single sample injection of 50 microl and in another sample injection the Cd and Pb isotopes were measured. Concentrations ranging from 5.0 to 16 microg l(-1) for Ba, from 0.50 to 1.1 microg l(-1) for Cd, from 6.0 to 50 microg l(-1) for Cu, from 0.8 to 18.8 microg l(-1) for Pb and from 46.0 to 230 microg l(-1) for Zn were found in saliva samples. Detection limits of 0.11, 0.03, 0.40, 0.05 and 0.59 microg l(-1) were determined for Ba, Cd, Cu, Pb and Zn, respectively. The concentrations found by isotope dilution were in agreement with those of the completely digested samples quantified by external calibration. The direct analysis of 30 samples per hour was attained with the proposed procedure, avoiding time-consuming digestion steps, contamination risks and matrix effects.     

Nafion‐Coated Bismuth Film Electrodes for the Determination of Trace Lead and Cadmium in Herbal Medicines by Anodic Stripping Voltammetry

A novel analytical procedure for the determination of Pb(II) and Cd(II) in herbal medicines by differential pulse anodic stripping voltammetry (DPASV) on Nafion‐coated bismuth film electrode (NCBFE) was proposed and experimentally validated. Various experimental parameters, which influenced the response of the NCBFE to these metals in real samples, were optimized. The results showed that there were well‐defined peaks of Pb and Cd in herb samples at deposition potential of ?1.2 V and deposition time of 300 s. The analytical performance of the NCBFE was evaluated in the presence of dissolved oxygen, with the determination limits of 0.35 µg·L^?1 for Pb and 0.72 µg·L^?1 for Cd and recoveries of 87.8% –105.4% for Pb and 89.5% –108.5% for Cd obtained from different samples. The Pb and Cd concentrations in the studied samples have been also determined by graphite furnace atomic absorption spectrometry (GFAAS), suggesting that there was a satisfactory agreement between the two techniques, with relative errors lower than 6.5% in all cases. The great advantages of the proposed method over the spectroscopic method were characterized by its simplicity, selectivity and short analysis time, simultaneous analysis of different metals and cost‐efficiency.     

石墨炉原子吸收测定土壤中的Cd Pb

摘要：为了提升石墨炉原子吸收测定土壤样品中Cd和Pb的准确度和测试效率,对样品前处理和仪器测试等条件进行优化选择,确定了低温电热板消解样品时,硝酸、氢氟酸、高氯酸的三酸比例和复溶方式以及采用海光GGX-920型石墨炉原子吸收测定Cd和Pb的升温程序、样品和基体改进剂加入量等条件。应用选定方法条件分别对土壤标准物质GBW07403、GBW07449水系沉积物 GBW07309进行6次测定,测定值Cd的相对标准偏差RSD：2.49%~4.67%,相对误差RE：-2.31% ~ 2.22%,测定值Pb的相对标准偏差RSD：1.98%~ 2.54%,相对误差RE：-1.88% ~ 2.11%。此方法精密度和准确度均达到标准要求,是一种准确而快速的检测方法,适合大批量的环境样品检测。     

Preparation and characterization of porous calcium titanate-based coated glass fiber filter material and its application in determination of lead and cadmium ion concentrations in water

Glass fiber filter coated with a porous block adsorption agent of calcium titanate (GPCTO) was prepared by the citric acid sol-gel method, and characterized by X-ray diffraction, scanning electron microscopy, and FTIR spectrophotometry. Its Pb2+ and Cd2+ adsorption properties from water were studied. Adsorption and elution were investigated under different conditions, as were the thermodynamics and kinetics of adsorption, using Cd ion as representative. Calcium titanate may react with glass fiber, forming Si-O-Ti and B-O-Ti bonds and becoming a composite adsorbent. The Pb and Cd ions were quantitatively retained at pH 4-9; their adsorption capacities by the GPCTO were 199.72 and 19.68 mg/g, respectively. The isothermal data were described by the Langmuir equation. The dynamic data followed the pseudo-second-order kinetic model well. The enthalpy change (AH) of the adsorption process was 37.160 kJ/mol. At various temperatures, Gibbs free energy changes (delta G) were negative, and entropy changes (delta S) were positive. The activation energy (Ea) was 38.127 kJ/mol for the adsorption. Cd ion adsorption by the GPCTO was endothermic and spontaneous. The adsorbed Pb and Cd ions were completely recovered by elution with 2 M HNO3. The Pb+ and Cd2+ concentration factors were up to 200. The method has been applied to the preconcentration for flame atomic absorption spectrometric determinations of trace Pb and Cd ions in water samples. The recoveries were 95.2 to 102.4% for Pb and 92.2 to 98.0% for Cd.     

High-throughput determination of seven trace elements in food samples by inductively coupled plasma-mass spectrometry

A method was developed for high-throughput determinations of 7 elements in food samples, namely antimony (Sb), arsenic (As), cadmium (Cd), chromium (Cr), lead (Pb), mercury (Hg), and tin (Sn). The samples were digested by closed-vessel microwave-assisted digestion using concentrated nitric acid (HNO3) as the medium, followed by microwave- assisted evaporation to concentrate the sample solutions before dilution to the desired volume. The microwave-assisted evaporation procedure effectively reduced the final acid concentration to around 8% before analysis by inductively coupled plasma-mass spectrometry (ICP-MS). This reduction allows determination by ICP-MS to proceed without further sample dilution, which would affect the detection limit. The method was validated, and method recoveries for As, Cd, Cr, Pb, and Hg were within the certified ranges of the chosen certified reference materials. Recoveries of the 7 elements from spiked samples ranged from 93.1 to 103.6%. The standard uncertainties of precision for the 7 elements were between 3.1 and 4.3%. Interlaboratory comparison studies for As, Cd, and Pb gave z-scores ranging from -0.2 to 0.3.     

Biomonitoring method for the simultaneous determination of cadmium and lead in whole blood by electrothermal atomic absorption spectrometry for assessment of environmental exposure

The aim of this work is to propose a biomonitoring method for the simultaneous determination of Cd and Pb in whole blood by simultaneous electrothermal atomic absorption spectrometry for assessment of environmental levels. A volume of 200 microL of whole blood was diluted in 500 microL of 0.2% (wv(-1)) Triton) X-100+2.0% (vv(-1)) HNO3. Trichloroacetic acid was added for protein precipitation and the supernatant analyzed. A mixture of 250 microg W+200 microg Rh as permanent and 2.0% (wv(-1)) NH4H2PO4 as co-injected modifiers were used. Characteristic masses and limits of detections (n=20, 3s) for Cd and Pb were 1.26 and 33 pg and 0.026 microg L(-1) and 0.65 microg L(-1), respectively. Repeatability ranged from 1.8 to 6.8% for Cd and 1.2 to 1.7% for Pb. The trueness of method was checked by the analysis of three Reference Materials: Lyphocheck Whole Blood Metals Control level 1 and Seronorm Trace Elements in Whole Blood levels 1 and 2. The found concentrations presented no statistical differences at the 95% confidence level. Blood samples from 40 volunteers without occupational exposure were analyzed and the concentrations ranged from 0.13 to 0.71 microg L(-1) (0.32+/-0.19 microg L(-1)) for Cd and 9.3 to 56.7 microg L(-1) (25.1+/-10.8 microgL(-1)) for Pb.     

ICP-AES法测定锌阳极中的铝、镉、铁、铜、铅

通过分析高频功率、雾化压力、辅助气流量和泵速等试验条件，建立了ICP-AES法测定锌阳极中铝、镉、铁、铜、铅的方法。用该方法测定锌阳极中的铝、镉、铁、铜、铅，其RSD分别为0.17%、0.63%、2.7%、5.2%、2.5%，回收率分别为99.3%-101.2%，99.3%-100.3%、97.1%-102.2%、97.8%-102.9%。对锌阳极试样进行测定，该方法的测定结果与GB4951-85方法的测定结果基本一致。